Tender For Lis Sheeri-Construction Of Cement Concrete Channel At Damaged Spots On Main Canal And Sub Minors At Spots, Jacketing Of Delivery Tanks And Providing Crate Work Near Supply Channel. (Amount Of Work:- Rs 237.14 Lacs)
Tender Value
2.37 Crore
Estimated cost
Bid Submission
13 Oct 2026
21 days left
EMD
4.75 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Baramulla → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Lis Sheeri-Construction Of Cement Concrete Channel At Damaged Spots On Main Canal And Sub Minors At Spots, Jacketing Of Delivery Tanks And Providing Crate Work Near Supply Channel. (Amount Of Work:- Rs 237.14 Lacs)
BOQ
| Sl. No. | Item Description |
| 1 | Electro Mechanical Works |
| 2 | Design, Supply, Installation, Testing and Commissioning of 20 Cusec, 43 m dynamic head Vertical Turbine pumping unit of lift Irrigation Scheme Sheeri-I as per following site conditions and specifications: Technical SpecificationsI. PUMP SPECIFICATION:1) Make: Kirloskar/Wilo/Flow more/Mather Platt or equivalent as per EOI of Superintending Engineer mechanical Circle Kashmir I&FC Department Srinagar.2) Model :To be quoted3) Type : Centrifugal Vertical Turbine pit mixed flow4) Discharge : 20 Cusec5) Total Dynamic Head : 43 meters 6) Pump power input at duty point :To be quoted 7) Water to be handled : Raw water containing silt 8) No. of stage: 2 9) Lubrication : Self water lubrication 10) Vibration Level: as per HIS 11) Noise Level: As per HIS 12) Sealing arrangement: Gland packed/Mechanical Seal/As per OEM 13) Discharge bend: below machine floor level 14) Pump efficiency at duty point without negative tolerance :85 % or above15) Speed (Rpm): 995 16) Diameter of Suction column pipe: To be quoted17) Diameter of Delivery : To be quoted 18) Material of Impeller : SS ASTM A351/ CF8M19) Material of Head shaft : SS AISI 410 / to be quoted20) Impeller key / Thrust ring/ retaine/ split ring/ shaft/ sleeves/coupling: SS 410 21) Material of Line shaft, column Shaft Bowl Shaft : SS AISI 410 22) Column pipe : Flanged column pipe fabricated out of MS plate of adequate thickness and length As per OEM 23) Material of Pump casing : Close fine grained cast iron confirming to IS-210 Grade-260 24) Strainer: Basket type MS Galvanised / to be quoted.25) Motor Stand/ Sole plate : MS as per IS 2062: 199226) Nuts and Bolts: High Tensile Steel/Carbon Steel27) Bowl assemblies Suction bellvand bowl shall be made :Close fine grained cast iron confirming to IS-210 Grade-260 28) Material of shaft sleeves :SS AISI 410 /as per OEM to be Quoted29) Impeller and wearing ring: SS ASTM A351/CF8M30) Discharge Head: MS Fabricated/ OEM II. Motor/Prime Mover Specifications:1) Type : Vertical Solid Shaft sq cage induction motor.2) Make : Kirloskar / ABB / Crompton/ equivalent make3) Speed : 995 rpm 4) Capacity : 452 HP5) No of phases : 03 phase 415 V + 10%, 50 Hz, AC supply.6) Winding : Copper wound squirrel cage7) Type of enclosure : TEFC8) Class of insulation: F9) IP Rating: 55.10) Duty type : S111) Motor efficiency: IE2 (95%)III. Pump unit shall be provided with suitable discharge head with proper stuffing box arrangement, non-reverse ratchet, coupling, sole plates, foundation bolts etc as per standard specification. The job also involves any welding work etc. required during installation of pumping unit at site shall be arranged by the firm itself. |
| 3 | Providing, fitting, testing and commissioning of 1 MVA Distribution transformer for LIS Sheeri-I11/ 0.433kV,1 Mva 3-Phase Distribution Transformer with Bimetallic Terminal Connectors Energy Level-2, (Copper Wound) and with LV Cable Box having detachable Aluminum Gland plate Transformers should have arrangements for vertical takeoff cable with OCTC (off ckt. Tap changer). Filling of transformer oil upto required level of the transformer.Make = Castrol, Servo, HP conforming to IS 335The Toil shall be filled in transformer at site |
| 4 | Supply Installation Testing and commissioning of 10 Ton Chain Pully Block with monorail for LIS Sheeri-I and having spur-gear configuration, enclosed load-bearing parts, an automatic load brake system, and carry an official ISI mark. Hand and load chains must be calibrated to provide a minimum 06-meter true vertical lift height. Unit must come integrated with a manual push/geared monorail travel trolley configured to sit tightly on the lower flange of the ISMB 300 bridge girder. (Approved makes: Induff, Globe, Pull-lift, or equivalent). The job also includes painting of ISMB beam by way removing/scrubbing old existing colour with the help of skilled painter , tools and tackles and then applying of metal primer coat then painting with two coats of A grade enamel yellow paint (preferable make: Neurolac, Berger, asian), All tools and tackles, skilled labour required for the completion of work shall be arranged by the firm it self. |
| 5 | Upgradation of 1 Mva Sub Station of LIS Sheeri-I of below mentioned Specification 1 Fabrication, supply, installation, testing & commissioning of 09 Mtr long M.S steel tubular poles (410 SP33) .. Each pole shall have suitable size of holes for accommodating nuts & bolts and base plate of suitable size fitted at the bottom for grouting. (pit depth = 1.35 Mtr) (02 No)2 Cement bottoming 1:2:4 mix as per Standards 0.5 cum per pole (02 Job)3 Supply, installation, testing of ISMC-75 channels with clamps, nuts & bolts, washers (9 feet x 7 no =63 feet = 19 mtr ) @ 6.8kg/mtr = 129.2kg + 15 kg nuts bolts clamps = 144.2 kg4 Providing and painting of one coat of red oxide paint and two coat of aluminum paint to MS pole. (02 job)5. Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required (06 No)5 Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required. (01 Set)6 Providing and fitting of 11 KV 200A 3-ph Gang operated Air Break Switch (01 Set)7 Providing of 11Kv DO Operating Rod (FRP) with min. 18 ft length (01 Job)8 Supply and erection of 200A horn gap fuse set suitable for 3 wire, 11 KV overhead lines. (01 Set)9 Providing and fitting of danger plate. (01 Job)10 Providing and fixing of anti-climbing device with clamps, etc. (02 Job)11 Providing and fitting of 0.5 ACSR with the help of skilled labor, tools & tackles. 150 Mtr12 Supplying and laying 25mm X 5mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (01 Job)13 Painting of old existing 1 Mva Transformer by way removing/scrubbing old existing color with the help of skilled painter, tools and tackles and then applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, Asian equivalent), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself. |
| 6 | Renovation/ upgradation to Existing 2000 Amp main control Pannel of LIS Sheeri-I having specifications as mentioned below: -1 Providing, fitting and testing of Main 2000 Amp ACB in Main Control panel, CN-CS 2000 of L&T/ Havells/ Schneider/ Equivalent make as per EOI of SE Mech. Circle Kmr. I&FC Department Srinagar 2000 A, 3 Pole, Breaking capacity 50 kA.2 Providing, fitting and testing of outgoing ACB for 20 cusec VT pumping unit in Main Control panel: CN-CS 800 C series fixed ACB of L&T/ Equivalent make as per EOI of SE Mech. Circle Kmr. I&FC Department Srinagar In 800 A, 3 Pole, Breaking capacity 50 kA with spreaders. (02 No)3 Providing, fitting and testing outgoing ACB for 10 cusec VT pumping unit in Main Control panel: CN-CS 630 C series fixed ACB of L&T/ Equivalent make as per EOI of SE Mech. Circle Kmr. I&FC Department Srinagar in 630 A, 3 Pole, Breaking capacity 50 kA with spreaders. (02 No)4 Providing, fitting and testing of 63 Amp MCCB in main control panel for Lightning. (01 No)5 Providing, fitting and testing of 96 mm analogue ammeters with selector switches and CT coil all complete 4 Nos.6 Providing, fitting and testing of 96 mm analogue voltmeters with selector switches all complete 4 Nos.7 Providing, fitting and testing of analogue frequency meter (45–55 Hz) 1 No.8 Providing, fitting and testing of 125 mm analogue ammeters with selector switches and CT coil all complete 1 Nos.9 Providing, fitting and testing of 125 mm analogue Voltmeter with selector switches all complete 1 Nos.10 Providing, fitting and testing of LED indications for phase for main control panel. (15 No)11 Replacement of damaged 1.5 sq mm copper control wiring with new one in main control panel with the help of skilled labor tools and tackles for the completion of work (15 mtr).12 Providing, fitting and testing of PVC wire ducts, ferrules, tinned copper lugs and terminal blocks.13 Painting of Main Control Pannel by way removing/scrubbing old existing color with the help of skilled painter, tools and tackles and then applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, Asian, equivalent), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself.14 Replacement of damaged Bus bar tapping, PVC wire ducts, ferrules, tinned copper lugs and terminal block in main control panel with new one with the help of skilled labor for the completion of job.Note: During the installation of new ACBs in main control panel any modification/New bus bar etc required during execution of work shall be arranged by the firm itself. |
| 7 | Copper Cable: Supply, installation, testing & commissioning of single core 630 sq mm XLPE insulated, and PVC outer sheathed copper cable to be laid from main control panel to voltage stabilizers to starters to 20 cusec pumping units . The job also includes the fitting of cable along the walls of the Pump house by using clamps and laid underground where ever necessary as per site requirement. The cable shall be thimble at each end with copper thimble using a crimping tool. The cable shall be of following specification Voltage: 1100V Insulation: XLPE insulated, PVC double sheathed Make of cable: Gloster/Havells/ Finolex /National/as approved in EOI SE Mechanical Kashmir Thimble: Dowell Make. |
| 8 | Supply, Installation, Testing & Commissioning of 600 KVA capacity copper wound voltage stabilizer at LIS Sheeri I of below mentioned specifications:i. Capacity: 600 Kva Three phaseii. Type: Manually controllediii. Cooling: Oil Coolediv. Make: Reputed makev. Input Voltage: 300-500 volts (phase to phase),200-270 volts (phase to Neutral)vi. Output Voltage: 415 volts +10 % (phase to phase)240 volts + 10 % (phase to Neutral) Suitable for: 100 % BALANCED vii. Application: Indoor typeviii. Phase: 3-Ph, 4 wiresix. Frequency: 50 HZ + 3 %x. Response time: Instantaneous (millisecond)xi. Mode of operation: Manualxii. Suitability: Suitable for all Power Factorsxiii. Duty Cycle: Continuous 24 Hrs.xiv. Efficiency: 98 % at full load.xv. Losses at No Load: As per standardsxvi. Losses at Full Load: As per standardsxvii. Laminations used: Imported low Losses CRGOxviii. Laminations – M4 Gradexix. Class of Insulation: Class-A. Greater Than 6 M ohmsxx. Break Down Strength: 500-volt AC for 1 minute (for whole unit)xxi. Transformer winding: Copper strip.xxii. Container: 2-3mm thick MS steel with enameled paintxxiii. Voltage regulator: 8/6 steps with suitable amperageADDITIONAL FEATURES:1 Earth fault protection.2 High Grade CRGO Lamination.3 99.9% pure copper.4 High efficiency.INSTRUMENT ACCESSORIES:1 Main “ON” indicating lamps in each phase.2 Voltmeter with input & output sides.3 Selector switch 03 no.4 Transformer Oil up to required level of the stabilizer Make = Castrol , Servo, Hp conforming to IS 335 The Toil shall be filled in stabilizer at siteGENERAL ARRANGEMENTS:The container shall have cooling radiators & mounted on sliding wheels, other fittings would include as follows: Lifting Lugs, Earthing Terminals-2 nos. Oil Level indicators, Rating Plate, Name plate, draining valve at appropriate place. The Job also include painting of voltage stabilizer by way applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, Asian ,equivalent ), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself. |
| 9 | Dismantling of 400 kva voltage stabilizers, opening top lid, taking out the voltage regulator and Core, checking all connection lead insulation and providing and fitting of new insulation wherever required for connection leads, refitting of voltage regulator and assembling voltage stabilizer properly after proper servicing/ repair. The job involves welding work to oil tank at leakage spots to make it leak proof. Connecting of leads of all incoming and outgoing connections and testing of Voltage Stabilizer at site on full load. The Job also include providing and fitting of new Voltmeter, Ampere meter having range (0-500) selector switch, phase indicating lamp, control wiring, bush rods both input and output. The Job also involves providing and filling of transformer oil / Type II inhibited oil conforming to IS 335 for Stabilizer up to required level and testing on full load. (Preferred make: Power oil/ Indian Oil Servo/ HPCL). The Job also include painting of voltage stabilizer by way removing/scrubbing old existing color with the help of skilled painter , tools and tackles and then applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, Asian), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself. |
| 10 | Supply, installation, testing & commissioning of 425 HP capacity fully automatic auto transformer starter of below mentioned specification.1 Providing, fitting and testing Main contractor assembly having a range not less than 1250 A, Make L&T/ABB/schneider/Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. (01 No)2 Providing, fitting and testing Delta contractor assembly having a range not less than 630 A, Make L& T/ABB/schneider Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. (01 No)3 Providing, fitting and testing Star contractor assembly having a range not less than 400 A, Make L&T/ ABB/schneider Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.(01 No)4 Providing, fitting and testing Thermal overload relay of suitable capacity MN series of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.(01 No)5 Providing, fitting and testing Motor protection relay of suitable capacity MN series of L&T/ ABB / Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. (01 No)6 Providing, fitting and testing Double timer assembly (electro pneumatic) having a range of 0 -60 second of L& T /ABB / Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. (01 No)7 Providing, fitting and testing Single phase preventer of suitable capacity with selectable under & over voltage of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.(01 No)8 Providing, fitting and testing Control MCB of suitable capacity amperes range.9 Providing, fitting and testing Electrolytic copper bus bar strips of suitable size & capacity duly tinned air insulated and mounted on suitable Bakelite insulation10 Providing, fitting and testing One number Digital/Amalog voltmeter 0-500V & one no. Ammeter digital/Analog type along with 3 No. CT coils having range 0- 500A fitted in each bus bar.Make L&T/ABB/AE/EE make.11 Providing, fitting and testing ON/OFF LED push button type RED & Green color of 5A-415V, 50HZ, L&T/ABB/Equivalent make.12 Providing, fitting and testing Frequency Meter, C.T coils and other accessories as per requirement/Design should be included.13 Providing, fitting and testing Complete internal wiring of the control panel for operating equipment by using adequate capacity single core copper wire of Havells/polycab/equivalent make. The wiring shall be fitted with plastic washers for identification of each wire at various joints.14 Panel for housing of all the equipment fabricated out 14 SWG gauge sheet metal of adequate size to house all the equipment with enough space to reach out to any equipment for repair/replacement. The panel shall have hinged door at the front with proper locking arrangements. The housing shall be provided with a base frame fabricated out of ISMC & welded /bolted at the bottom. The housing shall be provided with necessary cut out spaces for fitment of meters, push buttons actuator incoming & out coming connections. The panel shall be free standing, floor mounted, totally enclosed, vermin proof, the panel shall be RAL 7035/7032 Powder coated. The panel shall have air vents for proper ventilation. Auto Transformer coil shall be made out of 1st class electrolytic copper strips having suitable capacity for the above starter. The coil shall be provided with F class insulation tape. The coil shall have tapings taken out at 50%, 65% and 80% The Core of the auto transformer shall be fabricated out of 1st class silicon 90 grade pota sheets cut to size and then tightening of the same adequately. The auto-transformer tank shall be fabricated out of MS sheet of suitable thinness to make the tank leak proof. which shall have a lid at the top provided with holes for tightening the same of the tank. The tank shall have to be fitted at back side of the starter. o. Providing and fitting of high-grade low viscosity transformer oil (Make Castrol/Servo/ Hp) conforming to IS 335 up to the required level in the tank so that the auto- transformer coils get fully immersed. Adequate capacity electrolytic copper bus strips or cables shall be fitted for internal connections. |
| 11 | Electrification of Sheeri-I Pump House: |
| 12 | Providing and fitting of 1.5 sq. mm PVC insulated Copper wire of (Havells/anchor/ Polycab/Equivalent make) |
| 13 | Providing and fitting of PVC channel 1\\" size along with bend connections and other supports, square blocks, etc. |
| 14 | Providing and fitting of angle holders with ceiling rose. |
| 15 | Providing and fitting of 5 W LED bulbs (Havells/Eveready/syska or any other reputed make) |
| 16 | Providing, Fitting, Testing and Commissioning of 50-watt LED flood lights of Following Specifications.Specification:Type: LED flood lightMake: Havells/Crompton/Philips/Bajaj/ EquivalentRated Power: 50 watt.Mounting: WallIP Rating: IP65/66Body Material: AluminumUsage/Application: Outdoor |
| 17 | Providing and fitting of Switches (Anchors/SSK)06 A rating |
| 18 | Providing and fitting of lighting indicator (Anchor/ SSK) -06A rating |
| 19 | Providing and fitting of fan regulator with rotary step (SSK/Anchor) |
| 20 | Providing and fitting of 6A-2/3 pin-universal socket, 240V, 50 Hz, AC. |
| 21 | Enclosing box for switches (Topsun/ Anchor/ Equivalent) |
| 22 | Providing and fitting of 6 sq. mm PVC insulated Copper wire (Havells/anchor/ Polycab/Finolex/ Equivalent make) |
| 23 | Providing and fitting of SS combine box type at specified heating points. (Anchor/ SSK Equivalent) |
| 24 | Providing and fitting MCB 6A SP (Havells/Indo Asian/ Anchor/ Equivalent) for lighting circuits |
| 25 | Providing and fitting MCB 20A DP (Havells/Indo Asian/Anchor/ Equivalent) for heating circuit |
| 26 | Providing and fitting of 12-way MCB end box Benlo/ Anchor/ Havells/ SSK/ HPL/ Equivalent) |
| 27 | Providing, fitting and testing of ceiling fan \\"Orpat/Orient/bajaj/ Equivalent \\" make having sweep of 1200mn (48\\"). working on 230V, 50Hz, 16A.C. |
| 28 | Providing of korean blanket of ultra-soft and cozy double type for workers deputed at site having weight 8 kg |
| 29 | Providing of rechargeable 10W LED torch of Havells make for workers deputed at site |
| 30 | Tool Set: |
| 31 | Open Ended Spanner Set from 6x7 to 34x36- (Taparia/ Skil/ Stanley/ Equivalent) |
| 32 | Ring Spanner Set from 6x7 to 34x36 (Taparia/ Skil/ Stanley/ Equivalent) |
| 33 | Screw driver (2 in 1) short length (Taparia/ Skil/ Stanley/Equivalent) |
| 34 | Screw driver (2 in 1) long (Taparia/ Skil/ Stanley/Equivalent) |
| 35 | Club Hammer with handle (01 kg) (Taparia/ Skil/ Stanley/ Equivalent) |
| 36 | Heavy duty Pipe wrench 18\\" (Taparia/ Skil/ Stanley / Equivalent) |
| 37 | Heavy duty Pipe wrench 36\\" (Taparia/ Skil/ Stanley /Equivalent) |
| 38 | Grease gun (lever type 450 cubic capacity) |
| 39 | Supply of heavy duty 5.5 meter / 18 feet compact and foldable telescopic ladder having load bearing capacity 150 kg. |
| 40 | Providing and testing of hydraulic crimping tool with standard die sizes (min 10 nos.) from 25 to 500 sq mm (Jainsons/ Dowells/ Breeze Shears/Equivalent) |
| 41 | Sheeri-II |
| 42 | Supply, Installation, Testing and Commissioning of 30 Kw, 1465 RPM, 03 phase induction motor for 05 cusec Hz pumping unit no Ist at lift irrigation Sheeri-II of below mentioned specification of motor.1 Type: Horizontal type squirrel induction motor.2 Capacity: 30 KW3 Volt 380 +-15% 4 EFF 89%5 RPM 14656 Make: ABB/Kirloskar/Siemens/ as approved in EOI SE mechanical7 Class of Insulation: F type8 No of phases: 03 phase AC supply9 Winding Copper wound squirrel cage10 Type of enclosure: TEFC11 Coiling: Air cooled with fan mounting. The job includes all cost of material and labor, welding work for modification if any required for the fitment of the motor on existing base frame with new rubber tyre coupling set of suitable size for coupling of new motor with existing 05 cusec horizontal pumping unit no 1st at site. The job also includes the charge of providing of Palmative packing 5kg. |
| 43 | Supply, Installation, Testing & Commissioning of 400 KVA capacity copper wound voltage stabilizer at LIS Sheeri II of below mentioned specifications:1 Capacity: 400 KVA Three phase2 Type: Manually controlled3 Cooling: Oil Cooled4 Make: Reputed make5 Input Voltage: 270-460 volts (phase to phase), 200-270 volts (phase to Neutral)6 Output Voltage: 415 volts +10 % (phase to phase) 240 volts + 10 % (phase to Neutral) Suitable for: 100 % BALANCED 7 Application: Indoor type8 Phase: 3-Ph, 4 wires9 Frequency: 50 HZ + 3 %10 Response time: Instantaneous (millisecond)11 Mode of operation: Manual12 Suitability: Suitable for all Power Factors13 Duty Cycle: Continuous 24 Hrs.14 Efficiency: 98 % at full load.15 Losses at No Load: As per standards16 Losses at Full Load: As per standards17 Laminations used: Imported low Losses CRGO18 Laminations – M4 Grade19 Class of Insulation: Class-A. Greater Than 6 M ohms20 Break Down Strength: 500-volt AC for 1 minute (for whole unit)21 Transformer winding: Copper strip.22 Container: 2-3mm thick MS steel with enameled paint23 Voltage regulator: 8/6 steps with suitable amperageADDITIONAL FEATURES:1 Earth fault protection.2 High Grade CRGO Lamination.3 99.9% pure copper.4 High efficiency.INSTRUMENT ACCESSORIES:1 Main “ON” indicating lamps in each phase.2 Voltmeter with input & output sides.3 Selector switch 03 no.4 Transformer Oil upto required level of stabilizer Make = Castrol /HP/Servo conforming to IS 335The T-oil shall be filled in stabilizer at site.GENERAL ARRANGEMENTS:The container shall have cooling radiators & mounted on sliding wheels, other fittings would include as follows: Lifting Lugs, Earthing Terminals-2 nos. Oil Level indicators, Rating Plate, Name plate, draining valve at appropriate place. The Job also include painting of voltage stabilizer by way applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, Asian, equivalent), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself. |
| 44 | Renovation/ upgradation of existing 1000 Amp main control Pannel of LIS Sheeri-II having specifications as mentioned below: 1 Providing fitting and testing of 1000 Amp ACB in existing main control panel of L&T/Havells/Schneider/Equivalent as per EOI of SE make fixed type, having 3 Pole and breaking capacity 50 ka. (01 No) 2 Providing fitting and testing of 630 amp MCCB for 10 cusec Hz pumping unit in existing main control panel of Havells/L&T/Schenider/Equivalent make having 03 Pole and Breaking capacity 50 kA with spreaders etc. required during execution of work (01 No) 3 Providing fitting and testing of 800-amp MCCB for two 05 cusec Hz pumping unit (Heewan) in existing main control pannel of Havells/L&T/Schneider/Equivalent make having 03 Pole and Breaking capacity 50 kA with spreaders etc. required during execution of work (01 No)4 Providing fitting and testing of MCB: 63 A, 3 Pole , Breaking capacity 25 kA with spreaders . for lightning purpose (01 No)5 Providing fitting and testing of 100 Amp MCCB for in build FASD stater in Main control pannel for 05 cusec pumping units (fatehgarh) 03 pole having breaking capacity 36 ka make: L&T/Havells/ Standard or Equivalent (02 No)6 Providing fitting and testing of ML4, 3-pole contactor for in build FASD stater in Main control panel suitable to operate 415 V 50 Hz (Make L&T/Havells/Schneider) (04 No)7 Providing fitting and testing of ML3, 3-pole contactor for in build FASD stater in Main control panel suitable to operate 415 V 50 Hz (Make L&T/Havells/Schneider ) (02 No) 7. Providing fitting and testing MN5 thermal overload relay for in build FASD stater in Main control panel of specified relay range 45-75 A (Make: L&T or Equivalent) (02 No)8 Providing fitting and testing of Electro pneumatic timer assembly having a range of 0-60 sec of L&T/Havells/Schnieder. (02 No) 9 Providing fitting and testing 96 mm analogue ammeters with selector switches and CT coil all complete 6 Nos.10 Providing fitting and testing 96 mm analogue voltmeters with selector switches all complete 6 Nos.11 Providing fitting and testing analogue frequency meter (45–55 Hz) 5 No.12 Providing fitting and testing 125 mm analogue ammeters with selector switches and CT coil all complete 1 Nos.13 Providing fitting and testing 125 mm analogue Voltmeter with selector switches all complete 1 Nos.14 Providing, fitting and testing of LED indications for phase for main control panel. (15 No)15 Replacement of damaged 1.5 sq mm copper control wiring with new one in main control panel with the help of skilled labor tools and tackles for the completion of work (15 mtr).16 Painting of Main control panel by way removing/scrubbing old existing color with the help of skilled painter, tools and tackles and then applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, asian, equivalent), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself.17 Replacement of damaged Bus bar tapping, PVC wire ducts, ferrules, tinned copper lugs and terminal block in main control panel with new one with the help of skilled labor for the completion of job. Note: During the installation of new ACBs in main control panel any modification/ new bus bar etc. required during execution of work shall be arranged by the firm itself. |
| 45 | Supply, installation, testing & commissioning of 300 HP capacity fully automatic auto transformer starter suitable to operate 250 HP motor for LIS Sheeri-II of below mentioned specification.a. Providing, fitting and testing Main contractor assembly having a range not less than 450 A, Make L&T/ABB/schneider/Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.b. Providing, fitting and testing Delta contractor assembly having a range not less than 300A, Make L& T/ABB/schneider Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.c. Providing, fitting and testing Star contractor assembly having a range not less than 185 A, Make L&T/ ABB/schneider Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.d. Providing, fitting and testing Thermal overload relay of suitable capacity MN series of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.e. Providing, fitting and testing Motor protection relay of suitable capacity MN series of L&T/ ABB / Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.f. Providing, fitting and testing Double timer assembly (electro pneumatic) having a range of 0 -60 second of L& T /ABB / Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.g. Providing, fitting and testing Single phase preventer of suitable capacity with selectable under & over voltage of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar.h. Providing, fitting and testing Control MCB of suitable capacity amperes range.i. Providing, fitting and testing Electrolytic copper bus bar strips of suitable size & capacity duly tinned air insulated and mounted on suitable Bakelite insulationj. Providing, fitting and testing One number Digital/Amalog voltmeter 0-500V & one no. Ammeter digital/Analog type along with 3 No. CT coils having range 0- 500A fitted in each bus bar.Make L&T/ABB/AE/EE make.k. Providing, fitting and testing ON/OFF LED push button type RED & Green color of 5A-415V, 50HZ, L&T/ABB/Equivalent make.l. Providing, fitting and testing Frequency Meter, C.T coils and other accessories as per requirement/Design should be included.m. Providing, fitting and testing Complete internal wiring of the control panel for operating equipment by using adequate capacity single core copper wire of Havells/polycab/equivalent make. The wiring shall be fitted with plastic washers for identification of each wire at various joints.n. Panel for housing of all the equipment fabricated out 14 SWG gauge sheet metal of adequate size to house all the equipment with enough space to reach out to any equipment for repair/replacement. The panel shall have hinged door at the front with proper locking arrangements. The housing shall be provided with a base frame fabricated out of ISMC & welded /bolted at the bottom. The housing shall be provided with necessary cut out spaces for fitment of meters, push buttons actuator incoming & out coming connections. The panel shall be free standing, floor mounted, totally enclosed, vermin proof, the panel shall be RAL 7035/7032 Powder coated. The panel shall have air vents for proper ventilation. Auto Transformer coil shall be made out of 1st class electrolytic copper strips having suitable capacity for the above starter. The coil shall be provided with F class insulation tape.The coil shall have tapings taken out at 50%, 65% and 80% The Core of the auto transformer shall be fabricated out of 1st class silicon 90 grade pota sheets cut to size and then tightening of the same adequately. The auto-transformer tank shall be fabricated out of MS sheet of suitable thinness to make the tank leak proof. which shall have a lid at the top provided with holes for tightening the same of the tank.The tank shall have to be fitted at back side of the starter.o. Providing and fitting of high-grade low viscosity transformer oil (Make Castrol/Servo/ Hp) conforming to IS 335 up to the required level in the tank so that the auto- transformer coils get fully immersed. Adequate capacity electrolytic copper bus strips or cables shall be fitted for internal connections. |
| 46 | Upgradation of 630 kva Sub Station of LIS Sheeri-II of below mentioned Specification 1) Fabrication, supply, installation, testing & commissioning of 09 Mtr long M.S steel tubular poles (410 SP33) .. Each pole shall have suitable size of holes for accommodating nuts & bolts and base plate of suitable size fitted at the bottom for grouting.(pit depth = 1.35 Mtr) (02 No)2) Cement bottoming 1:2:4 mix as per Standards 0.5 cum per pole (02 Job)3) Supply, installation, testing of ISMC-75 channels with clamps, nuts & bolts, washers (9 feet x 7 no =63 feet = 19 mtr ) @ 6.8kg/mtr = 129.2kg + 15 kg nuts bolts clamps = 144.2 kg4) Providing and painting of one coat of red oxide paint and two coat of aluminum paint to MS pole. (02 job)5) Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required (06 No)6) Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required. (01 Set)7) Providing and fitting of 11 KV 200A 3-ph Gang operated Air Break Switch (01 Set)8) Providing of 11Kv DO Operating Rod (FRP) with min. 18 ft length (01 Job)9) Supply and erection of 200A horn gap fuse set suitable for 3 wire, 11 KV overhead lines. (01 Set)10) Providing and fitting of danger plate. (01 Job)11) Providing and fixing of anti-climbing device with clamps, etc. (02 Job)12) Providing and fitting of 0.5 ACSR with the help of skilled labor, tools & tackles. 150 Mtr13) Supplying and laying 25mm X 5mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (01 Job)14) Painting of 630 Kva Transformer by way removing/scrubbing old existing color with the help of skilled painter, tools and tackles and then applying one coat of epoxy primer and two coats of epoxy paint (preferable make: Nerolac, Berger, Asian, equivalent), All tools and tackles, skilled labor required for the completion of work shall be arranged by the firm itself. |
| 47 | Fabrication, providing and fitting of 300mm nominal dia. MS foot valve as per the below specifications: -1 Nominal diameter 300 mm2 Height 375mm3 Bell mouth 350 mm4 Sheet thickness 8 mm5 Seat plate thickness 16 mm6 No. of ports 1 7 Port diameter 300 mm8 Flap thickness 12 mmThe flaps to be hinged with SS hinge pin assembly having suitable counter weight and also a suitable washer/sole rubber gasket to be fixed with the flaps.A cylinder shaped MS strainer fabricated out of 16mm with a height of 300 mm built around equally spaced three horizontal rings ribbed vertically at a space of 25mm. the bottom of the foot valve shall be provided and fitted with steel section at above mentioned spaces. The job also includes the charge for dismantling of damaged /rusted foot valve from suction pipe by way of cutting rusted nuts and bolts and then fitting of new foot valve at same place by way of tightening new nuts and bolts, washers, welding work wherever required for the completion of work. Any modification like reducer, flanges etc. required during execution of work shall be arranged by the firm itself. The Job also include painting of one coat of red oxide paint and two coat of black bituminous paint with the help of painter, tool and tackles for the completion of work. |
| 48 | Supply, Installation, Testing and Commissioning of 250 mm dia VAG/AVK/ Kirloskar /Equivalent valve as per EOI of SE Mech, for lift Irrigation Scheme Sheeri-II of following Specification:Nominal Dia: 250mmBody: Cast Iron.Rating: PN-1.6Hinge Disc: Cast ironHinge Pin: AISI 410Body Ring: Leaded gunDisc Face: Natural Rubber.The job also includes the charge of Nuts, Bolts & Washer, matching flanges, welding work for fitting of valves, dismantling of unserviceable valves and other allied works required at site for the completion of work. The Job also include painting of one coat of red oxide paint and two coat of black bituminous paint. |
| 49 | Supply Installation Testing and commissioning of 05 Ton Chain Pully Block with monorail for pumping units at LIS Sheeri-II and having spur-gear configuration, enclosed load-bearing parts, an automatic load brake system, and carry an official ISI mark. Hand and load chains must be calibrated to provide a minimum 06-meter true vertical lift height. Unit must come integrated with a manual push/geared monorail travel trolley configured to sit tightly on the lower flange of the ISMB 250 bridge girder. (Approved makes: Induff, Globe, Pull-lift, or equivalent). The job also includes application of metal primer coat to entire gantry structure after proper surface preparation and then painting with two coats of A grade enamel black paint to vertical pole and yellow paint to Horizontal MB Beams. |
| 50 | Supply Installation Testing and commissioning of 2 Ton Chain Pully Block with monorail for suction side at LIS Sheeri-II and having spur-gear configuration, enclosed load-bearing parts, an automatic load brake system, and carry an official ISI mark. Hand and load chains must be calibrated to provide a minimum 06-meter true vertical lift height. Unit must come integrated with a manual push/geared monorail travel trolley configured to sit tightly on the lower flange of the ISMB bridge girder. (Approved makes: Induff, Globe, Pull-lift, or equivalent). The Job also include painting of one coat of red oxide paint and two coat of black bituminous paint to vertical post of gantry, working platform, suction pipes etc and two yellow coat to ISMB beam. |
| 51 | Electrification of Sheeri-II Pump House: |
| 52 | Providing and fitting of 1.5 sq. mm PVC insulated Copper wire of (Havells/anchor/ Polycab make/equivalent) |
| 53 | Providing and fitting of PVC channel 1\\" size along with bend connections and other supports, square blocks, etc. |
| 54 | Providing and fitting of angle holders with ceiling rose. |
| 55 | Providing and fitting of 5 W LED bulbs (Havells/Eveready/syska or any other reputed make) |
| 56 | Providing , Fitting, Testing and Commissioning of 50 watt LED flood lights of Following Secifications.Specification:Type: LED flood lightMake: Havells/Crompton/Philips/Bajaj/equivalentRated Power: 50 watt.Mounting : WallIP Rating : IP65/66Body Material : AluminumUsage/Application : Outdoor |
| 57 | Providing and fitting of Switches (Anchors/SSK/equivalent)06 A rating |
| 58 | Providing and fitting of lighting indicator (Anchor/ SSK/equivalent) -06A rating |
| 59 | Providing and fitting of fan regulator with rotary step (SSK/Anchor/equivalent) |
| 60 | Providing and fitting of 6A-2/3 pin-universal socket, 240V, 50 Hz, AC. |
| 61 | Enclosing box for switches (Topsun/ Anchor/equivalent) |
| 62 | Providing and fitting of 6 sq. mm PVC insulated Copper wire (Havells/anchor/ Polycab/Finolex /equivalent make) |
| 63 | Providing and fitting of SS combine box type at specified heating points. (Anchor/ SSK/equivalent) |
| 64 | Providing and fitting MCB 6A SP (Havells/IndoAsian/ Anchor/equivalent) for lighting circuits |
| 65 | Providing and fitting MCB 20A DP (Havells/IndoAsian/Ancor/equivalent) for heating circuit |
| 66 | Providing and fitting of 12-way MCB end box Benlo/ Anchor/ Havells/ SSK/ HPL/equivalent) |
| 67 | Providing, fitting and testing of ceiling fan \\"Orpat/Orient/bajaj/equivalent \\" make having sweep of 1200mn (48\\"). working on 230V, 50Hz, 16A.C. |
| 68 | Providing of Korean blanket of ultra-soft and cozy double type for workers deputed at site having weight 8 kg |
| 69 | Providing of rechargeable 10W LED torch of Havells make for workers deputed at site |
| 70 | Tool Set: |
| 71 | Open Ended Spanner Set from 6x7 to 34x36- (Taparia/ Skil/ Stanley/equivalent) |
| 72 | Ring Spanner Set from 6x7 to 34x36 (Taparia/ Skil/ Stanley/equivalent) |
| 73 | Screw driver (2 in 1) short length (Taparia/ Skil/ Stanley/equivalent) |
| 74 | Screw driver (2 in 1) long (Taparia/ Skil/ Stanley/equivalent) |
| 75 | Club Hammer with handle (01 kg) (Taparia/ Skil/ Stanley/equivalent) |
| 76 | Heavy duty Pipe wrench 18\\" (Taparia/ Skil/ Stanley/ equivalent) |
| 77 | Heavy duty Pipe wrench 36\\" (Taparia/ Skil/ Stanley /equivalent) |
| 78 | Grease gun (lever type 450 cubic capacity) |
| 79 | Supply of heavy duty 5.5 meter / 18 feet compact and foldable telescopic ladder having load bearing capacity 150 kg. |
| 80 | providing and testing of hydraulic crimping tool with standard die sizes (min 10 nos.) from 25 to 500 sq mm (Jainsons/ Dowells/ Breeze Shears/equivalent) |
| 81 | CIVIL WORKS |
| 82 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge; -. All kind of Soil |
| 83 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:2.9.1 All kinds of soil : |
| 84 | Spreading of sludge, dump manure or/and good earth in required thickness as per directions of officer in-charge (cost of sludge, dump manure or /and good earth to be paid separately) |
| 85 | Providing and laying in position dry stone soiling incl. cost of stones |
| 86 | Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centering and shuttering. All work up to plinth level with: 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) |
| 87 | Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centering and shuttering. All work up to plinth level with:1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) |
| 88 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level; - 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) |
| 89 | Centering and shuttering including strutting, propping etc. and removal of form work for: Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs andsteps etc. |
| 90 | 12mm Cement plaster of mix: 1:4 (1 cement: 4 fine sand) |
| 91 | Hand-packing stones in wire-crates; excluding cost of crates and stones |
| 92 | Supply of Quarry stones 2nd class. |
| 93 | Cost of crate |
| 94 | Carriage of material by Mechanical Transport including loading, unloading and stacking up to site of work. |
| 95 | Stone soiling Quarry for an avg. lead of 12 kms |
| 96 | Aggregate. 20mm for an average lead of 45 kms |
| 97 | Aggregate. 40mm for an avg. lead 45 kms |
| 98 | Sand for an Avg. lead15 kms |
| 99 | Cement for an avg. lead 10 km |
| 100 | Crates From avg. lead 8 km |
| 101 | Carriage of material by Mechanical Transport including loading, unloading and stacking up to site of work. |
| 102 | Stone soiling Quarry |
| 103 | Aggregate. 20mm |
| 104 | Aggregate. 40mm |
| 105 | Cement Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender