Tender For Providing Additional Ac Units, Sets Camera Cat Cable And Incoming Ltug Cable In The Pre-Fabricated Workshop Building In Government Polytechnic College, Trichirappalli -22
Tender Value
15.19 Lakhs
Estimated cost
Bid Submission
06 Oct 2026
2 days left
EMD
16000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tiruchirappalli → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing Additional Ac Units, Sets Camera Cat Cable And Incoming Ltug Cable In The Pre-Fabricated Workshop Building In Government Polytechnic College, Trichirappalli -22
BOQ
| Sl. No. | Item Description |
| 1 | Supply and fixing of 1No.MS pillar box made up of 16SWG MS sheet for outer body and mains chamber with angle iron frame work for outer frames and intermediate supports for following mains chamber, bus bar arrangements and bottom supports. The pillar box should be mounted on suitable foundation concrete on ground with one coat of red oxide and two coats of synthetic enamel paint with lock and key arrangements and DANGER board and necessary superscriptions complete housing mains. |
| 2 | Supply and Laying of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. |
| 3 | Supply and fixing of brass cable gland for 3 1/2 X 185 sqmm PVC LTUG armoured cable with earth connection. |
| 4 | Supply and providing cable end termination of 3 1/2 X 185 sq. mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete |
| 5 | Supply erection, testing and commissioning of 2.0 TR (6000 K.cal/Hr) ABS Plastic Split type Air conditioner conforming to IS 1391 (Part-2) 1992 with Amdt No. 1 to 2 fitted with rotary compressor operating on refrigerant R-32/non CFC suitable for wall mounting for operation on 230V, 50HZ single phase AC supply with star rating of 3 star as per BEE specification and capable of performing the functions of CoolingDehumidifyingAir CirculatingFilteringThe installation works for the above split type AC units includes the following.1.Mounting / Fitting Indoor and outdoor units at their respective locations.2. Laying refrigerant pipeline of required length connecting not exceeding 3 metre distance and both units after drilling hole/holes in the wall if required.3. Insulating the suction pipe with expanded polyethylene foam 5mm tubing.4. Laying 15mm dia flexible PVC drain pipe to throw out the condensate water being formed within the indoor unit.5. Leakage testing the entire system unit.6. Charging refrigerant gas in the unit.7. Suitable electric wiring to be provided with 2.5 Sq mm PVC insulated copper wire between indoor and outdoor units up to 6 Mtrs length and up to switch within 3 Meters of location of indoor unit (Make: Carrier/Voltas/equivalent) |
| 6 | Supply of 5 KVA Electronic Automatic Voltage Stabilizer (Higher end) with Input Voltage range of 170 Volt – 270 Volt and Output Voltage range 200Volts to 240 Volts with High and Low Voltage cut off and 3 minutes time delay relay with demonstration |
| 7 | Supply and fixing of water drain pipe line (1\\" PVC pipe). |
| 8 | Supply and fixing of MS stand for fixing Outdoor unit. |
| 9 | Supply and laying of 5/8\\" and 3/8\\" copper refrigerant pipe of 0.8mm thick with 2.5 sqmm 3 core chord between indoor and outdoor unit. (Extra beyond 3 mts supplied with AC unit) . |
| 10 | Supply and installation of 4 Megapixel resolution Infrared Network Bullet Camera with IR Range upto 30 meters,120dB WDR,Video Compression in H.264/MJPEG format, Day & Night auto switch IR cut filter, IP67 Protection level with mounting Bracket included (Make and Model: Hikvision/ Dahua/ Equivalent). |
| 11 | Supply and laying of UTP Cat 6 camera cable through 25mm PVC rigid pipe concealed in the wall/ceiling with necessary connection and making good of the concealed portion with painting of suitable colour Make : Finolex or Dlink or equivalent |
| 12 | Sub switch Panel: Supply and Erection of 400A capacity Dust and Vermin Proof Cubical Panel Board made up of 16 SWG CRCA steel with supply and fixing of the following interior mounting fuse switches with HRC fuses arranged in two Horizontal rows with one switch over the other with a central bus bar chamber and two nos of Horizontal cable chambers at the two ends one on each side next to the fuse switch chamber and confirming to IE rules.EB INCOMER: 400A FP switch disconnector fuse units interior only with HRC fuse Double Break Switch -1 NoOUTGOING:250A TPN switch disconnector fuse units interior only with HRC fuse Double Break Switch -2Nos200A TPN switch disconnector fuse units interior only with HRC fuse Double Break Switch -2Nos125A TPN switch disconnector fuse units interior only with HRC fuse Double Break Switch -4 Nos(All the TPN Switch should be Siemens with Front Handle) Suitable The bus bar chamber will consist of suitable size of tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE Rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans. 2 Nos 25x3mm tinned copper flats should be provided all round the panel for earth bus.The fuse Switches should be connected with the phase and natural buses with suitable size of rigid copper flat/rod and each switch should be connected with the 2 Nos earth bus with 2 runs of No.8 SWG rigid Tinned copper rod with suitable lugs. Phase and neutral tinned buses should be tinned properly.The panel should have a separate metering chamber at the top side consisting of 0-600V Voltmeter with Selector Switch, 0-400A Ammeter with Selector Switch and C.T arrangement Pilot lamps, toggle switches, fuse unit (Siemens) indicator lamps should be provided with control switches and fuse unit The panel should be Powder Coat paint of approved colour, approved by the site officer and also the danger board . |
| 13 | Earthing as per the ISI specification with an earth electrode of 2.10metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mmx50mmx6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry. |
| 14 | Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection. |
| 15 | Supply and laying of 3 1/2 X 240 sq.mm PVC armoured LTUG cable in a existing trench |
| 16 | Supply and fixing of brass cable gland for 3 1/2 X 240 samm PVC LTUG armoured cable with earth connection |
| 17 | Supply and providing cable end termination of 3 1/2 X 240 sq.mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete |
| 18 | Supply and fixing of LT cable route indicator with suitable angle not less than 38mm x 38mm 6mm and 0.6mtr long excavation of earth to a depth of 0.6 mtr and concreting the ground level and making good of the ground as directed by the departmental officers. |
| 19 | Supply and fixing of 2 Nos. 6/16A two module socket, 2Nos 16A module switch on suitable module surface mounting Box (GI) with module cover plate (plastic) on wall with connections. (Higher end) |
| 20 | Supply and run of 2 of 4 sqmm PVC insulated SC unsheathed FRLS copper conductor of 1100V Grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sqmm PVC insulated sc unsheathed copper wire with painting of suitable colour. |
| 21 | Supply, Installation and termination of RJ 45 Cat-6 I/O Socket with, Back box, Face plate with surface mount. (Make:D link/Legrand/ Equivalent). |
| 22 | Supply, fixing and termination of Cat 6 UTP Patch cord (higher end) of 2 metre.Make:D link or ADC or Molex or Digilink or equivalent. |
| 23 | Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End |
| 24 | Supply and fixing of 65 mm dia. (2 -1/2\\") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 30W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed FRLS copper leads from SMC box to fitting and with painting of suitable colour |
| 25 | Coil earth to street light poles with No.8 SWG GI wire of 11.5metres of length in which 10metres of total length compressed into a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth. |
| 26 | Supply and laying of 4x10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 meter putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. |
| 27 | Supply and clamping of 4 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps |
| 28 | Supply and clamping of 4x10 sq.mm PVC LTUG armoured LTUG cable through 32mm dia G.I pipe on post or on wall with MS Clamps. |
| 29 | Supply and fixing of brass cable gland for 4X10 sq.mm PVC LTUG armoured cable with earth connection |
| 30 | Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable MS pipe on I beam or grider beam support and remaining wall portion in suitable MS pipe concealed in wall with MS accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End. |
| 31 | Supply and fixing of 100W High bay LED IP66 with suitable special type of MS clamps with PVC unsheathed copper leads from terminals to the fittings. (Higher end) |
| 32 | Supply and fixing of 450 mm wall mounting oscillating fan with suitable bolts and nuts complete with connection. (Higher end) |
| 33 | Supply and fixing of 1No 6A/16A 2module socket (higher end) concealed in suitable MS modular (GI) Box covered with modular white cover plate in flush with wall with earth connection |
| 34 | Supply and fixing of 1No 16A flush type control switch (higher end) concealed in suitable MS modular GI Box covered with modular white cover plate in flush with wall with earth connection |
| 35 | Supply and fixing of 65 mm dia. (2 -1/2\\") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 30W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed FRLS copper leads from SMC box to fitting and with painting of suitable colour |
| 36 | Supply and installation of 24 port Gigabyte semi-managed 10/100/1000 Mbps switch (higher end) with 24 port jack panel and necessary accessories. (Make: Netgear or Cisco or HP or equivalent) |
| 37 | Supply and installation of 16port Gigabyte semi-managed 10/100/1000 Mbps switch (higher end) with 24 port jack panel and necessary accessories. (Make: Netgear or Cisco or HP or equivalent) |
| 38 | Supply and installation 19\\" 9U three tier MS Rack for housing LAN Switches with top and Bottom Cable Entry provision along with necessary power distribution unit,cable manager, fan and Lockable Toughened Glass Door. |
| 39 | GST 18 % Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender