Tender For Repairs To Flooring, Joinery, Plumbing, Sanitary Fittings, Roof, False Ceiling And Misc Works At Aerial Bay Under Ge(S) Diglipur.
Tender Value
40 Lakhs
Estimated cost
Bid Submission
10 Oct 2026
18 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
North and Middle Andaman → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Flooring, Joinery, Plumbing, Sanitary Fittings, Roof, False Ceiling And Misc Works At Aerial Bay Under Ge(S) Diglipur.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 2 | Dismantling of ceiling boards (fibre,pulp, insulation,etc.) of any thicknes, including cover fillets complete all as specified and as directed. |
| 3 | Demolition of cement concrete of any description and in any position (unreinforced) in ground floor/paving/plinth exceeding 15cm thick below or above ground level including removing of rubbish to out side MOD land complete all as specified and as directed. |
| 4 | Demolition of Reinforced Cement Concrete of any description and any position not otherwise specifically provided for and reinforcement cut as required to facilitate demolition including removing of rubbish to out side MOD land complete all as specified and as directed. |
| 5 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillors etc, but excluding aslar facing, dressed stonework and precast concrete article built in cement mortar including removing of rubbish to out side MOD land complete all as specified and as directed. |
| 6 | Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and as directed. |
| 7 | Dismantling wrought iron or mild steel or stainless steel work of any description not otherwise provided for complete. |
| 8 | Taking down cement plaster any description on brick or stone walls, roof plaster etc, including raking out joints,hacking for key, scrubbing down with water, complete all as specified and as directed. |
| 9 | Taking down chowkat or frames with shutters (without taking off shutters from the frames exc. 1.5 Sqm and n.exc. 4.0 Sqm each complete all as specified and as directed. |
| 10 | Taking down chowkat or frames with shutters (without taking off shutters from the frames n.exc. 1.5 Sqm each complete all as specified and as directed. |
| 11 | Taking down Chowkhats or frames exc. 1.5 sq. m but n.exc. 4 sq. m each complete all as aspecified and as directed. |
| 12 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern as in rainwater gutter/ roof coverings complete all as aspecified and as directed. |
| 13 | Resecuring or erasing and adjusting without taking down of shutter of any description exc. 1.0 sqm and n.exc. 2.0 sqm each including necessary screws and finishing the surface complete all as specified and as directed. |
| 14 | Taking down and refixing in the same opening of shutter of any description exc. 1.0 sqm and n.exc. 2.0 sqm each including necessary screws and finishing the surface complete all as specified and as directed. |
| 15 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 16 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as aspecified and as directed. |
| 17 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as aspecified and as directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 18 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as aspecified and as directed.Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 19 | S&F 1st class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed. |
| 20 | S&F 35mm thick Glazed and skeleton shutters, divided in to squares with plain, chamfered or rounded open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as aspecified and as directed. |
| 21 | S&F 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as aspecified and as directed. |
| 22 | S&F 100mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as aspecified and as directed. |
| 23 | Ditto as per item no 22 above but 150 mm long ditto |
| 24 | S&F 100mm long Butt hinges, medium weight, cold rolled stainless steel, and fixed complete all as aspecified and as directed. |
| 25 | S&F 100mm long Aluminium anodised, barrel tower bolts of extruded section complete all as aspecified and as directed. |
| 26 | Ditto as per item no 25 above but 150 mm long ditto |
| 27 | S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as aspecified and as directed. |
| 28 | S&F in aluminium alloy wire cloth 0.45 mm nominal dia of wire & average width of aperture 1.40mm and fixed with wooden beading and tinned tack or galvanised wire staples complete all as specified and as directed. |
| 29 | S&F 4mm thickness Sheet glass,ordinary quality and glazing with oil putty in square exc. 0.5 sq. m in each pane complete all as aspecified and as directed. |
| 30 | S&F in repairs 150mm long Aluminium anodised, barrel tower bolts of extruded section complete all as aspecified and as directed. |
| 31 | S&F in repairs Floor door stopper 150mm over all length of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as aspecified and as directed. |
| 32 | S&F in repair for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 33 | S&F in repair for Aluminium extruded section body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed |
| 34 | S&F anodised aluminium frame for doors, windows, partitions, ventilators with or more rebates including joining cleat for fixing etc, complete all as aspecified and as directed. |
| 35 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as aspecified and as directed. |
| 36 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 37 | M & L for powder coated aluminum grill of design No DG-104, 7.5mm thick sections of decogrill or of equivalent approved make with 1 mm thick 'F' sections of suitable size complete all as specified and directed |
| 38 | S&F Non AC plain building board 6mm thick ceiling fixed with size of grid 605X605mm, anodised aluminium snap grid (main/cross tee section) shall be supported at ends all along the wall with aluminium angle of size 40mmx25mmx2mm and The main and cross tees shall be jointed at junction/crossings with anodized aluminium angle bracket of size 15mmx15mmx1.5mm frame work for false ceiling with Hangers 6 mm dia. G.I. complete all as specified and as directed. |
| 39 | Repairs to Aluminum window replacing of worn out friction hinges, handles and tightening of corners complete all as specified and as directed. |
| 40 | Repairs to alumunum door shutters as touching on floor by removing the shutter and repalcing the defective hinges, tightening all screws and refixing the same complete for free movement of shutters complete all as aspecified and as directed. |
| 41 | M&L for 18 to 20 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as aspecified and as directed. |
| 42 | M&L for 18 to 20 mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on both face complete all as specified and as directed. |
| 43 | S&F in repairs 75mm Hasp and staple, aluminium anodised, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as aspecified and as directed. |
| 44 | M&L for granite (of any type) 20mm thick work ( table rubbed and polish to mirror finsh) in a steps, jambs, pillers, window sills, cooking platform and like in cement motor (1:4) including pointiong in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite stone with grinding and polishing over and including 15mm thick cement mortar CM (1:4) complete all as as specified and as directed. |
| 45 | M&L for Reinforced cement concrete in type B1 (1:2:4) (using 20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and kitchen platforms complete all as specified and as directed. |
| 46 | Use and Waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, kitchen platforms and similar work, not exceeding 200mm thick for fair finished surfaces of concrete complete all as aspecified and as directed. |
| 47 | M&L for mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for slabs ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 48 | S&F in repair for 15mm bore Chromium plated Fancy type Bip taps, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 49 | S&F in repairs for 15mm bore brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed. |
| 50 | S&F in repairs for 15mm bore fancy type stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as aspecified and as directed. |
| 51 | S&F in repair for 20mm bore gunmetal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as aspecified and as directed. |
| 52 | S&F in repairs for 25mm bore ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for brass ferrule complete all as specified ans as directed. |
| 53 | S&F in repairs vitreous China wash basin (WHB) of size 550mmX400mm white flat back,tap wastchain and plug and porciline stopper but including all connected items i.e. brackets and 15mm bore CP pillar tap cast copper alloy fancy type and PVC connections with PTMT nuts and washers for 600mm long pipe complete all as aspecified and as directed. |
| 54 | S&F in repair for 15mm bore CP pillar tap cast copper alloy fancy type swan neck screwed down high pressure, with long screwed shank and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 55 | S&Fin repair vitreous china wash down water closet pan EWC(pedestral pattern) white (excluding flushing cistern and flush pipe) with P or S trap and including plastic water closet seat cover white, closed pattern with flat bottom and cover including connection to drain and flushing pipe etc complete all as specified and as directed. |
| 56 | S&F in repairs vitreous china squatting pan “Orissa pattern\\" size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including provision of lime concrete bed, making good the disturb surface complete all as specified and as directed. |
| 57 | S&F in repairs for 10litre capacity low level flushing cistern, moulded from virgin poly propylene make parry ware brand slimline single flush complete all as aspecified and as directed. |
| 58 | S&F in repairs for plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hanging device complete all as aspecified and as directed. |
| 59 | S&F in repair for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as aspecified and as directed. |
| 60 | S&F in repairs for 600mm X 450mm bevelled edge mirror 6 mm thick of selected quality glass, mounted on 6mm thick AC building board or commercial pvc and fixed to walls with CP brass screws and washers complete all as aspecified and as directed. |
| 61 | S&F in repair for Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as aspecified and as directed. |
| 62 | S&F in repair for Soap dish holder, approximate size 160 x 160 x 90mm, any type, fixed to plugs with chromium plated brass screws complete all as aspecified and as directed. |
| 63 | Supplying and laying of 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls and ceiling or laid in floors including taking down complete all as aspecified and as directed. |
| 64 | Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls and ceiling or laid in floors including taking down complete all as aspecified and as directed. |
| 65 | S&F in repair for sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 66 | S&F in repair for stainless steel plate rack 1.1mm thick weight not less than 7kg/each of size 75cmx75cmx25cm or of nearby size as approved by GE complete all as specified and as directed. |
| 67 | S&F in repair for PVC waste coupling of 40mm dia half or full threaded complete all as aspecified and as directed. |
| 68 | S&F in repair for PVC connections 15mm size with PTMT nuts and washers for 600mm long pipe complete all as specified and as directed. |
| 69 | S&F in repair for 32 to 40 mm size 600mm long PVC waste pipe complete all as specified and as directed. |
| 70 | M&L for repair for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as aspecified and as directed. |
| 71 | S&F aluminium anodised Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc including taking down complete all as specified and as directed. |
| 72 | M&L for precast cement concrete solid block masonry exc. 10cm in width using PCC (1:3:6) type C-1 (using 20mm graded aggregate) set in cement mortar 1:6 complete all as specified and as directed. |
| 73 | M&L for 10mm thick in CM (1:6) rendering on brick or concrete surfaces finished even and smooth (without using extra cement), complete all as specified and as directed. |
| 74 | M&L for Preparing newly plastered surfaces of walls and applying two coats of distemper oil emultion on walls with applying plaster of paris putty of 1mm thickness over plastered surface to prepare surface even and smooth complete all as specified and as directed. |
| 75 | M&L for Plain cement concrete (1:2:4) type-B1 (using 20mm graded aggregate) 75mm thick as in plinth protection all as specified and as directed. |
| 76 | M&L for 40 mm thick plain cement concrete (1:2:4) type B1 (20mm graded stone aggregate) finished the surface even and fair complete all as specified and directed. |
| 77 | M&L for Vitrified Ceramic coloured tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles exc. 0.36 sqm and not exceeding 1.0 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screeding 15mm thick on floor surfaces in cement and sand mortar (1:6) complete all as specified and as directed. |
| 78 | M&L for Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screeding 15mm thick on floor surfaces in cement and sand mortar (1:6) complete all as specified and as directed. |
| 79 | Ditto as per item no 78 above but exc. 0.11 sqm but not exc. 0.18 sqm ditto |
| 80 | M&L for Glazed ceramic coloured tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including backing coat 10mm thick on wall surfaces in cement and sand mortar (1:4) complete all as specified and as directed. |
| 81 | Ditto as per item no 80 above but vertical surface 450x 300x 7 mm thick ditto |
| 82 | M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over of pink primer complete all as specifed and as directed. |
| 83 | M&L for preparation of old painted steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint on steel surfaces complete all as specifed and as directed. |
| 84 | S&F Pre-painted galvalume aluminum zinc coating AZ-150 GSM GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and as directed. |
| 85 | S&F Pre-painted galvalume aluminum zinc coating AZ-150 GSM GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/rain water gutter/valley gutter/cladding to wall, fixed with self tapping screws complete all as specifed and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender