Tender For special Repair To Jcos/Or Md Accn P-02, P-51, P-218 And P-255 And special Repair To Bldg No T-14 Of 135 Inf Bde Under Ge Roorkee
Tender Value
Ref. Documents
Estimated cost
Bid Submission
09 Oct 2026
13 days left
EMD
95700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Haridwar → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Jcos/Or Md Accn P-02, P-51, P-218 And P-255 And special Repair To Bldg No T-14 Of 135 Inf Bde Under Ge Roorkee
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet/ Chimney and removal of debris and rubbish out side MoD land complete all as specified and directed. |
| 2 | M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 3 | M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab complete all as specified and directed. |
| 4 | Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc. 100 mm) complete all as specified and directed. |
| 5 | Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness (below or above ground level ) including removal of rubbish out side complex (MoD land), complete all as specified and directed. |
| 6 | M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg). Plinth protection laid to a slope of 1 in 24 in alternate basis system. Each bay shall not exceed 3m in length 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed. |
| 7 | M&L for PCC (1:4:8) ty D-2 using 40mm graded stone aggregates as in levelling course/sub base of path, floor tiles in bathroom and WC complete all as specified and directed. |
| 8 | M&L PCC type B-1 (1:2:4) (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed |
| 9 | M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregates as in levelling course over RCC roof/floor slabs, cills, steps, parapets, filing in steel chowkats, copings, and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified & directed |
| 10 | Surface excavation n. exc 30cm deep and averaging 15cm deep and getting in soft/loose soil complete all as specified and directed. |
| 11 | Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n exc 1.50 m above the starting point complete all as specified and directed. |
| 12 | M&L for hard core of broken stone boulder of gage n.exc 63mm deposited, spread and levelled in layers n.exc 15 cm thick watered and rammed to a true surfaces complete all as specified and directed. |
| 13 | Supply and laying sand (20 mm thickness) for cushioning to interlocking paver block complete all as specified and directed. |
| 14 | M&L for 60 mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed. |
| 15 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 16 | M&L brick work with sub class \\"B\\" bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and directed. |
| 17 | M&L for Brick work with sub clas \\"B\\" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed. |
| 18 | Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipe up to 150 mm bore complete all as specified and directed. |
| 19 | S&F PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/ fixtures fixed on wall or in trenches or in floor complete all as specified and directed. |
| 20 | Ditto all as above but 75mm nominal outside diameter. |
| 21 | S&F PVC (SWR) vent cowl suitable for 75 mm pipe complete all as specified and directed. |
| 22 | S&F 110 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed |
| 23 | Ditto all as above but 75 mm bore. |
| 24 | S&F in repair PVC (SWR) floor trap/Nahani trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete complete all as specified and directed. |
| 25 | S&F PVC (SWR) reducers 110mm dia, complete all as specified and directed. |
| 26 | S&F in repair 100 mm pipe stack clamps out of 50mm x 5 mm flat iron including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed. |
| 27 | Ditto all as above but 75 mm bore pipe. |
| 28 | S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed. |
| 29 | Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed. |
| 30 | M&L coloured non skid tile 7 to 8mm thick (square/ rectangular) area of each tiles exc.o.06 sqm n exc, 0.18 sqm in floor etc. set and jointed with neat cement slurry and pointed in colur cement to match including 15 mm thick screed bed in cm (1:6) complete all as specified and directed. |
| 31 | M&L for joint free coloured glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 complete all as specified and directed. |
| 32 | S&F Vitrified Ceramic tiles 8 to 10 mm thick light shade/drak shade (square/rectangular) polished, area of each tiles exc 0.18 sqm n. exc 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement including 15 mm thick screed bed in CM 1:6 complete all as specified and directed |
| 33 | S&F Vitrified Ceramic tiles 8 to 10 mm thick light/dark shade (square/rectangular) polished, area of each tiles exc 0.18 sqm exc 0.36 Sqm, in vertical surface such as skirting and dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement including 10 mm thick back plaster in CM 1:4 complete all as specified and directed. |
| 34 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the premises complete all as specified and directed |
| 35 | M&L machine cut kota stone slab flooring 18-20 mm thick over cement screed base 20mm thick screed bed in bedding layer in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the the slab including grinding, rubbing and polishing complete all as specified and directed. |
| 36 | M&L kota stone mirror polished slab with uniform texture of 16-18 mm thick in trader of steps (to be flushed and provided with three Nos of grooves at the end on each step), riser of steps, skirting, dado and pillars in one single piece (size decided by GE) laid over and including cement screed 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, bevelled edge of corner etc complete all as specified and directed. |
| 37 | M&L for granite 16-18 mm thick (table rubbed and polished) in cooking platforms and laid over cement screed mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of front side if required at site complete all as specified and directed. |
| 38 | Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) and removal of rubbish out of defence land complete all as specified and directed. (Note : All roots of plant on either on wall or roof shall be removed and making good the disturbed surfaces. The rate quoted be the contractor shall be deemed to be included in the unit rates) |
| 39 | Demolition of Mud Phuska in roofs,any thickness including plastering and leeping of any thickness upto 30cm deep complete all as specified and directed.(Note: All roots of plant on either on wall or roof to be removed and making good the distributed surfaces. |
| 40 | M&L for 40mm thick brick tiles laid on 15mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on RCC surface complete all as specified and directed. |
| 41 | M&L for rendering 20 mm thick cement plaster in CM (1:3) finished even and smooth w/o using extra cement and using waterproofing compound on fair faces of brick work or concrete surfaces complete all as specified and directed. Note - WPC will be measured and paid for separately.) |
| 42 | Taking down old existing water proofing treatment from the top of RCC/arch slab, including taking down exsiting PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed |
| 43 | M&L for cleaning of concrete or plastered surfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed evenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thick APP modified polymeric water proofing membrane minimum weight 3.6 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat of bituminous aluminum paint @ 0.20 kg per Sqm complete all as specified & directed. |
| 44 | Taking down chowkhat or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed. |
| 45 | Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed. |
| 46 | S&F factory made pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC (1:2:4) Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 47 | S&F factory made pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 105x60mm made out of 1.25mm MS sheets including PCC (1:2:4) Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 48 | Cutting holes in brick walls exc half bk wall but n exc one bk wall built in cement mortar or cement lime mortar and stone walls built in lime mortar or for inserting holdfasts and making good dismantalled portion in CM (1:3) or cement concrete (1:2:4) type B1 as required complete all as specified and directed. |
| 49 | S&F MS work as in holdfasts, wind ties, plane angle cleats for securing purlins to wooden trusses or rafters etc complete all as specified and directed. |
| 50 | S&F factory made steel shutter shall be made out of angle iron 35x35x5mm and 3 nos 25x25x3mm as cross support in frame of door and covered with 1.00mm thick MS sheet, running welding with frame, with locking arrangement complete all specified and directed. |
| 51 | S&F 35mm thick factory made Glazed and skeleton shutters using second class hard wood, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 52 | S&F 30mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 53 | M&L for built in MS steel cup board with pressed steel frame of size 75 mmx45mmx1.25 mm th with pressed steel shutter 1mm th Godrej pattern fixed to masonry wall by hold fast made out of 25x3 mm flat iron including ms hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of ms peg set of 3 pegs including spray including locking arrangement painting with two coats of synthetic enamel paint over one coat of red oxide primer with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surface of frame & shutter and making good disturbed portion in PCC 1:2:4 complete all as specified and directed. |
| 54 | S&F factory made gauged shutter shall be made out of angle iron 35x35x5mm (outer frame) and 25x25x5mm (middle rail 2 nos, 150 mm apart from each other) and 1.0mm thick steel sheet covering on middle rail, 10mm Square bars @ 100mm C/C fixed vertical as grill complete with stainless steel fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide as shown on drawing all specified and directed by Engr-in-charge. |
| 55 | S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS -14856 complete all as specified and directed. |
| 56 | S&F FRP door frames three legged of cross section 90x45mm having single rebate 32mmx15mm. The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminated shall be 2mm thick, frame shall be covered with fiber glass from all sides ms flat iron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed. |
| 57 | S&F 100 mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin, complete all as specified and directed. |
| 58 | S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed. |
| 59 | S&F Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed. |
| 60 | Ditto all as above but 150 mm long. |
| 61 | S&F Extruded aluminium alloy handles, fabricated type, anodised of size 150mm size long complete all as specified and directed. |
| 62 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of 140mm long complete all as specified and directed. |
| 63 | M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 64 | M&L Preparation of new or previously untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 65 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified & directed |
| 66 | M&L for powder coated aluminium anodised window sliding type (3 shutters type) with sash bars, aluminium sections weighing 0.55 Kg/m(min) including stainless steel wire mesh, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame, including 5 to 6 mm thick plain glass and all as specified & directed by Engr-in-charge. (Note :- Weight shall be measured before fixing of glass and wire cloth). |
| 67 | M&L for powder coated (50 micron thick) aluminium ventilator fixed type (partly glazed and partly gauzed) with gasket, glazing clip etc, weight of frame not less than 0.55 Kg/RM and weight of shutter frame not less than 0.425 Kg/RM including necessary joining cleats,rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, including 3 to 4 mm thick pin headed glass complete all as specified and directed. (Note :- Weight shall be measured before fixing of glass and wire cloth). |
| 68 | S&F stainless steel (grade-304) grills made of hollow tubes section including welding, grinding, buffing polishing and making curvatures wherever required and fitting the same with necessary holdfasts/SS dash fastners with nut & bolts of required size, complete all as specified and directed. |
| 69 | S&F in repairs for 18mm thick Multi layer water proof ply wood fixed with screws to timber frame work for cabinet case both sides covered with and including cost of 0.8mm thick decorative laminates, Mica type 1 of surface finished, colour, pattern as approved fixed with approved adhesive and the thickness of the shutter is edge lipped by 18 mm width x 1 mm thick PVC sheet using solvent cement etc. including ,magnet, piono hinges, handles as required Nos complete all as specified and directed. |
| 70 | Ditto all as above but for 9mm thick |
| 71 | M&L Frame work as in door chowkhat with angle iron welded together ends of angle shouldered and fixed to opening and welding 3 Nos mild steel butt hinges, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhat( Butt hinges paid separately) complete all as specified and directed |
| 72 | Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MoD land) complete all as specified and directed. |
| 73 | M&L Rendering 5mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed. |
| 74 | M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed. |
| 75 | M&L Rendering 15 mm thick in CM 1:4 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) complete all as specified and directed. |
| 76 | Supply only liquid water proofing compound complete all as specified and directed. |
| 77 | M&L for preparing newly plastered surface of wall and applying two coats of oil bound distemper including a coat of 1 mm thick wall care putty with preparation of plastered surfaces complete all as specified and directed. |
| 78 | M&L for new plasterd surface applying two coats of distemper oil emulsion white or tinted over and including a layer of 3mm thick wall care putty on wall complete all as specified and directed. |
| 79 | M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and applying two coats of oil bound distemper, over and including a coat of 1 mm thick wall care putty with preparation of plastered surfaces complete all as specified and directed. |
| 80 | M&L for preparation of old decorated wall surfaces by complete removal of existing treatment on walls including cornices by broming down with steel brush, scrapping down smoke soot, moulds moss and efflorescent salts and trading oil and grease spots and applying two coat of Premium Acrylic Smooth exterior paint with Silicone additives of required shade over applied @1.43 ltr/10 sqm over and includling 2mm thick wall care putty and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified & directed |
| 81 | M&L for Preparing of new plastered surface of wall and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade over and includling 2mm thick wall care putty : New work (Two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified & directed |
| 82 | M&L for preparation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified and directed. |
| 83 | Ditto all as above but two coat on old ceiling surface. |
| 84 | Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed. |
| 85 | Ditto all as above but 20 mm bore |
| 86 | S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors/trenches etc complete all as specified and directed. |
| 87 | Ditto all as above but 20 mm bore. |
| 88 | M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed. |
| 89 | Dismantling of RCC/PVC water tanks exc 250 liters and n.exc 500 liters capacity of any condition or type complete all as specified and directed. |
| 90 | S&F white colour Rotational moulded polyethylene water storage tank 500 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and directed. |
| 91 | S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed. |
| 92 | S&F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed. |
| 93 | S&F in repair vitreous chinaware coloured wash hand basin (WHB) size 550mm x 400mm, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed. |
| 94 | S&F in repairs PVC duel action symphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve and float including brackets and flush pipe complete all as specified and directed. |
| 95 | S&F in repair stainless steel sink AISI 316 grade without drainage board of 1 mm thick with plug, washer and waste, including bedding in cement mortar to dwarf wall or including CP Waste, PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowlsize 410mm x 330mm x 160mm or more complete all as specified and directed. |
| 96 | S&F in repair Chromium plated tubular towel rail, 25mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and with hooks, brackets & end caps fixed with brass screws complete all as specified and directed . |
| 97 | S&F wall mixer with over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed. |
| 98 | S&F in repair Brass chromium plated shower rose 125mm size with CP breass arm not less than 240mm long complete all as specified and directed. |
| 99 | S&F in repair looking mirror 600x450mm beveled edge 5.5 mm thick selected quality glass, mounted on 6 mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washers complete all as specified and directed. |
| 100 | S&F in repair Stainless steel cromium plated Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 101 | S&F in repairs 15mm bore Pillar tap of Chromium plated high pressure screwed for iron pipe and fixed etc complete all as specified and directed. |
| 102 | S&F in repair, Sheet Glass Shelf/corner Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and directed. |
| 103 | S&F in repair Stainless steel 4 shelf wall mounted kitchen utensils rack, Dish rack with plate & cutlery stand of size 18x24 inches, fixed to wall plugs and chromium plated brass screws complete all as specified and directed. |
| 104 | S&F in repiars vitreous china squatting pan (Orissa pattern) long pan including provision of cement concrete (1:5:10) bedding fixed in repair size 580x440mm white with intergral footrest with 'P' or 'S' trap complete (excluding flushing cistern and flush) Complete all as specified and directed |
| 105 | S&F in repair stainless steel peg set of six of size 480x38x2mm complete all as specified and directed. |
| 106 | S&F in repair 15 mm dia stop cock/angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle,with long shank and cup flench screwed both ends for iron or for union complete all as specified and directed. |
| 107 | S&F in repair bib taps fancy type brass cromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 108 | S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM (1:4) to floor/ nahani traps etc complete all as specified and directed. |
| 109 | S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed. |
| 110 | M&L for cutting hole of 230x230x230mm four Nos in walls, filling with PCC (1:2:4) Ty B-1 using 12.5mm thick stone aggregate incl fixing of 1Nos angle iron of size 50mmx50mm x6mm in C shape supported with 02x50x50x6mm angle iron down side angular shape over all lenght approx 6.22 Rm each stand including running welding with other angle, incl 2 coat of synthetic enamal paint over a coat of red oxide primer complete all as specified and directed. |
| 111 | S&F in repair curtain rod Stainless steel fancy type curtain rod 20 mm dia incl Brackets and knobs complete all as specified and directed. |
| 112 | M&L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas, wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finihes with and incl material and labore in CM 1:4 mixed with WPC/PCC (1:3:6) type B0/Bk work in CM 1:4 as required at site and as directed by Engr-in-Charge |
| 113 | S&F in repair PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks/flushing cistern complete all as specified & directed |
| 114 | Dismantling of floor of WC and bath not exc 500mm deep and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.(c) M&L for a glass fiber reinforced acrylic modified cementitious coating system with base coat @ 1.50 Kg/Sqm glass fiber reinforcement and top coat with seal-107 @ 1.50 Kg/Sqm.(d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with as specified.(e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall.(f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.(g) The area of Each WC portion is n.exc 2.00 Sqm each.Note : The work will be executed by authorised manufacturers/ applicator. |
| 115 | M&L for repair to RCC chajja (irrespective size) by cleaning, replastering in cement mortar 1:3 mixed with integral water proofing compound over 40mm thick (average) PCC padding in CM 1:2:4 Type B-0 (mixed with water proofing compound) to a required gradient or slope as directed by Engr-in-Charge and the plaster will extended upto 300mm on wall/roof surface to avoid leakage/seepage. Junction of old and new plaster will be well bonded with application of water proofing compound. Drip course or groove of siae 25mm x 4mm will be provided at the edge of bottom surface of the chajja. (Note:- Rates for cement plaster, WPC, PCC and formwork and specilist labours etc required for full completion of item shall be deemed to be included in the rates quoted against this item of BOQ by the contractor). |
| 116 | M&L 15 mm thick rendering in CM 1:4 inside and outside wall of manhole, drain etc of brick work/concrete surfaces finished even and smooth (with out using extra cement) complete all as specified and directed. |
| 117 | M&L for PCC (1:3:6) type C-1 (20 mm graded aggregate) as in copping, surface channel, benching of manhole/drain etc slightly rounded or chamfered angles and throating, as directed incl finish the surfaces smooth without using extra cement complete all as specified and directed. |
| 118 | Excavating in post holes in soft/loose soil each n exc 0.5 cum, getting out, and returning filling in and ramming with concrete around, and removing surplus soil to a distance n exc 50 m complete all as specified and directed. |
| 119 | M&L PCC (1:3:6) type C-2 using 40 mm grade stone aggregate as in foundation , filling and mass concrete complete all as specified and directed. |
| 120 | M&L MS Steel work in roof tubular trusses/purline/column/nut bolts/ base plate including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240. |
| 121 | Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed. |
| 122 | S&F for pre-painted, galvalume aluminium zinc coating GI based profiled steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa AZ-150, as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 123 | S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa AZ-150 as in ridge, roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 124 | Dismantling structural steel work including doors, gates, railings etc, but excluding framed truss etc complete all as specified and directed. |
| 125 | Dismantling timber scantlings 40 sq. cm and over in section, framed work in any position complete all as specified and directed. |
| 126 | Dismantling of wall and ceiling board or insulation board (fibre, pulp, insulation etc) or insulation board/slabs/blankets any thickness including cover fillet and removal from site complete all as specified and directed. |
| 127 | M&L for Providing and fixing false ceiling of designer tiles(high pressure steam Cured) of 4mm thickness (as per IS:14862) of size 595x595mm and any one of the design in true horizontal level, suspended on inner locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grms, both side inclusive and black painted groove on all T webs) consisting of main “T” runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, 1200mm long spaced between main “T” at 600mm C/C to form a grid of 1200x600mm and secondly cross “T” of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of 1200x600mm panel to form grids of 600x600mm and wall angle 15x20x0.36mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized butterfly level clips, spaced at 1200mm c/c along main “T”, bottom exposed width of 15mm of all “T” sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5 mm width, all complete at all heights as per directions of EIC. |
| 128 | Dismantling and taking down carefully U/S copper/aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. |
| 129 | Dismantling and taking down carefully sub-main wiring/ service wire of any size including wooden batten etc and and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. |
| 130 | Dismantling and taking down carefully existing DB's any type and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. |
| 131 | M&L for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of GI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) as earth wire connected with main common earth dolly complete all as specified and directed for the following :-One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp complete all specified and directed. |
| 132 | One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way Piano type switch complete all specified and directed. |
| 133 | One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed. |
| 134 | One light point controlled by two No two way switch complete all as specified and directed. |
| 135 | All as per item No 131 here-in-before but wiring with 2.5 sqmm single core multi stranded copper conductor 1100 V grade PVC insulated FRLS-H but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm FRLS-H cable as earthwire complete all specified and directed. |
| 136 | S&F switch piano flush type white finish 5/6 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed. |
| 137 | S&F switch piano flush type white finish 5/6 Amps, single pole two way, 230 volts, 50 hz complete all as specified & directed. |
| 138 | S&F socket out let 2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed. |
| 139 | S&F switch piano flush type white finish 15/16 Amps single pole one way, 230 volts, 50 hz all as specified and directed |
| 140 | S&F socket out let 5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed. |
| 141 | M&L bell push AC, SP 240 volts flush type 5/6 Amps, 230 volts, 50 hz complete all as specified and directed. |
| 142 | S&F fan regulator socket type 100W, flush stepped type, electronic, compatible with BLDC fan complete all as specified and directed. |
| 143 | S&F in replacement of electric call bell ding dong type, AC, 240V, 50Hz complete all as specified and directed. |
| 144 | M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 145 | S&F lamp holder (Angular/Straight), insulated body, with back plate for batten fitting complete all as specified & directed. |
| 146 | S&F LED bulb 12 watt B-22 suitable for holder complete all as specified and directed. |
| 147 | S&F LED tube light batten 20 watts 4 fts extruded polycarbonate housing, translucent diffuser with LED light source, 2000 lumen, natural white ,surge protection range- 2KV, voltage protection range 120-280 VAC with intergrated driver and surge protection complete all as specified and directed. |
| 148 | S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9/10 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories complete all as specified and directed. |
| 149 | S&F in repair Ceiling fan complete with three blades down rod, accessories 230 V, 1200mm sweep with minimum air delivery of 210 CFM (BLDC) with remote operated complete all as specified and directed .Note: Old Ceiling fan to be deposited in MES store Yard |
| 150 | S&F in repair Exhaust fan Steel body AC single phase 230/240 Volt of size 300 mm sweep complete with louvers including making whole on wall to fix exhaust fan and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed.Note: Old exhaust fan to be deposited in MES store Yard |
| 151 | Ditto all as above but size 250mm sweep |
| 152 | S&F in repair water heater with temp regulator storage type of capacity 25 Ltr , five star rated AC sinle phase 230 volts 50 Hz, vertical mounting type with stainless steel inner tank of approved colour, with adjustable temperature, plug top and Hot and cold PVC connection complete all as specified and directed.Note: Old unserviceable geyser to be deposited in MES store yard. |
| 153 | S&F single pole & neutral plastic enclosure prewired power unit with 25 Amp rated MCB and 25 Amp rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board including taking down existing unserviceable plug & socket board of any description and making good with cement plaster, putty and paint to match with the existing surface all as specified. |
| 154 | S&F LED 30 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver, including bracket clamp and fixing accessories complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed. |
| 155 | S&F sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS-H) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed. |
| 156 | Ditto all as above but of size 4sqmm |
| 157 | S&F sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed. |
| 158 | S&F MCB, SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 159 | S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 160 | S&F of MCCB/MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar of capacity 125 Amps, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface. |
| 161 | S&F MCCB 100A, 15/16 KA, 4 Pole, 415 V, Ics=100% Icu, 50 Hz with fixed thermal magnetic release fixed in Vertical TPN complete all as specified and directed. |
| 162 | M&L for circuit/submain wiring with single core 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS) 1100Volts grade drawn through existing rigid PVC conduit for Inverter wiring complete all as specified and directed. |
| 163 | M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick burried directly in ground. (earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80 mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed .Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. |
| 164 | Dismantling & taking out old unserviceable LT UG cable & Supplying & laying in replacement of LT UG cable ( Conforming to IS 1554) ISI marked 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor in trenches/ducts/through HDPE pipe under roads of size 25 sqmm 4 core complete all as specifed and directed. Note;- The earth work shall be measured and paid seprately under appropriate item of Sch A. |
| 165 | Excavation in trenches not exc. 1.5 mtr wide and not exc 1.5 mtr depth in any type of soil (soft/loose/hard/dense soil) for laying/taking up/taking down of UG Cable/water pipes/ foundation of any size and type including levelling of bottom surface to required level all as specified and directed by Engineer-in-Charge |
| 166 | Returning filling in soft/disintegrated soil including spreading levelling watering and well ramming in layers n.exc 25cm each layer complete all as specified and directed. |
| 167 | M&L for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/ floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed. |
| 168 | S&F GI tubing light grade ISI marked of 50 mm bore dia in wall complete all as specified and directed. |
| 169 | Drilling and tapping GI water mains 50mm bore (in position) for branch connections of the internal dia 20mm, complete all as specified and directed. |
| 170 | S&F straight plain brass ferrules (or connecting screws) screwed both ends and fixed to water mains for tapping branch connection of 20 mm bore pipe, complete all as specified and directed. |
| 171 | Taking down existing unserviceable gate valve & Supply and Fix Gun metal gate valve, ISI marked, with iron wheel head screwed both ends for iron pipe, fixed in repairs complete of size 20 mm bore Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender