Tender For Special Repair For Power House (S-4) Building At installation Kardip, Kamorta. 8848/E8
Tender Value
13 Lakhs
Estimated cost
Bid Submission
09 Oct 2026
5 days left
EMD
26000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nicobars → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair For Power House (S-4) Building At installation Kardip, Kamorta. 8848/E8
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 2 | S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 3 | S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 4 | M&L for MS work as in Wind Tie in roof and MS structural works in trusses, etc with screwed ends including nuts, washers and mild steel plates for walls chimneys, roofs arches etc any kind rods and straining bolts conforming to Fe-290 Gde-165 complete all as specified . |
| 5 | Taking down roof trusses, coupled rafters or trussed beams including taking down trusses etc., for renewal of any defective members and reassembling for Clear span upto 4 meters complete all as specified and as directed. |
| 6 | Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats conforming to Fe-410W(Gde E-250) quality A complete all as specified and as directed. |
| 7 | M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and as directed |
| 8 | M&L for preparation of new or previously untreated steel surfaces of any description n.exc 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and as directed |
| 9 | Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for complete all as specified and as directed. |
| 10 | Supply and fix framed work such as grills , grating ,etc with ends of bars shouldered and or revated for forged in to spike, framed guard bars barred iron doors, ladders, balusters, walk ways raling framed work for water tanks similar work confirming to Fe-290 Gde E-165 complete all as specified and directed. |
| 11 | Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 Sqm each as doors, windows & ventilators etc. and removal from site complete all as specified and directed by Engr-in-charge. |
| 12 | Material and labour for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with shine pinned at joints, fixed to wall and making good to wall all as specified and directed. |
| 13 | Supply and fixing 2nd class hardwood factory made plain framed panelled shutters 35mm thick with lock rail and with panels of 12mm thick commercial veneered particle board veneers on both side or with 9mm thick BWP commercial ply, size of members of shutters as specified in IS 1003-Part-I, kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 14 | Supply and fix stainless steel Butt hinges stainless steel hinge pin and fixed 100mm size complete all as specified and directed. |
| 15 | Supply and fix extruded aluminium alloy handles, fabricated type, anodised 150mm size complete all as specified and as directed |
| 16 | Supply and fixing aluminium alloy,anodised, extruded section, barrel tower bolt 150mm long complete all as specified and as directed by Eng-in-charge. |
| 17 | Supply and Fixing 4mm thick ordinary quality glass with film cover, ordinary quality and glazing with oil and putty in square not exc 0.5 sqm in each pane complete all as specified and as directed. |
| 18 | Material and labour for Preparation of new wooden surface of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over pink primer including preparation of new wooden surface all as directed and as specified. |
| 19 | Demolition of brick work / stone boulder / PCC block masonary, built in cement mortar or cement lime mortar including all quoins, arches pillars, etc but excluding ashlar facing, dressed stone works, precast concrete articles and precast concrete block wallings complete all as specified and as directed. |
| 20 | M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 21 | Material and labour for 15 mm thick rendering on brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick using water proofing compound @3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directed.Note: Water proofing compound shall be measured separately. |
| 22 | Supply only integral water proofing compound all as specified and as directed. |
| 23 | Material & Labour for preparation of newly plastered surfaces of walls and applying two coats cement based paint over a coat of primer complete all as specified and as directed. |
| 24 | Material and labour for rendering 10mm thick in Cement Mortar 1:4 on fair faces of brick walls or on concrete surfaces, finished even and smooth,without using extra cement complete all as specified and directed. |
| 25 | M&L for digital design glazed ceramic coloured tiles in vertical surface of size of each tile 300 x 450 mm /350x250 mm and 7 to 8 mm thick fixed to set and joint in neat cement slurry and pointed in white or coloured cement to match the same complete all as specified and directed. |
| 26 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 27 | Material and labour for hard core with broken stone or boulders of gauge not exceeding 63 mm, deposited, spread, and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface all as specified and as directed. |
| 28 | Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork, complete all as specified and as directed. |
| 29 | Material and labour for roughening surfaces of old concrete by picking , sweeping clean and washing down with water to remove dust etc, complete all as specified and as directed. |
| 30 | Material and labour for 50mm thick plain cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in as in leveling course including use of form work as necessary complete all as specified and as directed. |
| 31 | Material and labour for chequered cement concrete tiles 30cm x 30cm x 25mm with grey cement and pigment, hydraulically machine pressed, set, jointed and pointed in neat cement slurry to match colour of tiles, over and including 15mm thick screed in CM 1:6 in floors complete all as specified and as directed. |
| 32 | Material and labour for Plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in copings, kneelers, apex stones,bed plates, kerbs, bed block for hold fast including necessary form work all as specified and as directed. |
| 33 | Supply and fix plastic dividing strips 1.5mm thick and 22mm wide all as specified and as directed. |
| 34 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators sockets etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc. |
| 35 | M&L point wiring complete with 1.5 Sqm sincle core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc, all as specified and as directed for the following :- |
| 36 | (a)One light point or one light point controlled by one switch |
| 37 | (b)One light point or one exhaust fan/ fan point controlled by one switch |
| 38 | (c) One 3 pin socket outlet 5 Amps on same board |
| 39 | (d) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board. Please Enable Macros to View BoQ information |
| 40 | (d) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender