Tender For Executive Engineer Jsv Division Nadaun
Tender Value
7.65 Lakhs
Estimated cost
Bid Submission
26 Sep 2026
7 days left
EMD
15303
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hamirpur → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Executive Engineer Jsv Division Nadaun
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation trenches etc. in all kinds of soil such as pick jumper work blasting soft or hard rock chiselling insoft/hard rockahiselling in soft/hard including wedging out a rock where blasting is prohibited and stacking the excavted soil up to all lead clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidatio of all as laser by and watering and then disposing surplus excavated earth as directed by the Engineer-in-charge in all leads and lifts |
| 2 | Providing and laying in pusition cement concrete of specified grade excluding the cost of cr and shuttering - All work up to plinth level: 1:3:6 (1 Cement: 3 marse sand): 6 graded stone aggregate 40 mm nominal size) the cost of cratering |
| 3 | Providing and laying cement concrete 1:4:8(1 cement 4 sand graded stone aggregate 40 mm N/size)and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts as per direction and to the entire satisfaction of the Engineer-in-charge |
| 4 | Providing and laying cement concrete 1:1.5:3(1cement:1.5sand.3 graded stone aggregate 20mm nominal size) finishing with curing complete (excluding the cost of form) work in |
| 5 | Foundation, Footing, Bases of columns & the like & the mass concrete within all leads and lifts as per the direction of Engineer-in-charge. |
| 6 | Wall any thickness but not less than 0.10sts thickness) attached pillasters buttresser plinth & string courses etc. from top found Jevel upto floor two level |
| 7 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centering, shuttering strutting and propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for insitu reinforced concrete and plain (Vertical) |
| 8 | Vertical surfaces such as walls(any thickness) partitions and the like including attached pilasters, buttresses, plinth and string courses etc. upto floor two level and the like complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge. |
| 9 | Bending binding and placing Tor steel reinforcement for the work including fixing in position including cost of binding wire upto all floor level as per direction and to the entire satisfaction of Engineer in charge |
| 10 | laying, jointing & testing in trenches GMS/MS Tubes (L/M class) tube fittings (Earthwork in trenchses to be measured & paid for separately) 125mm |
| 11 | Providing and Fixing of CI. Sluice valves Leader/Kirloskar make of following diameter with hand wheel as per 15:14846-2000 (Class PN-16) (including brass spindle as per 2906-1984 complete with bolts nuts, rubber insertion etc. and as per direction and to the entire satisfaction of the Engineer-in-charge. |
| 12 | 125mm (PN 1.00) |
| 13 | Construction chamber for sluice valevewith CI Surface box 100mm tip dia,160mm bottom dia & 180mm deep (inside) with chained LID RCC top 1:2:4 mix (1cement 2 sand:4 grade stone aggregate 20mm nomial size) 100mm thick foundation concrete 1:5:10 mix (1cement:5 sand:10grade stone aggregate 40mm nominal size )& inside plastering with cement mortor 1:3 (1cement:3sand) finished with floating coat of neat cement /i/c curing complete :600*600*750mm inside size wih 150mm thicks walls of RCC 1:2:4 (1cemen :2 sand:4 grade stone aggregate 20mm nominal size) complete withform work& reinfocement with 6mm bars at not exceeding 150mm centres both Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysSep 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender