Tender For special Repair To Bldg No. Old-60/F (Guard House) At Jp Line And Office Complex & Stores Including Toilets In Bldg Nos. P-34 & P-35 (Main Office) Of Aro And Provn Of Boundary Wall Near Bldg No. P-436 At Mil Stn Alwar
Tender Value
42.56 Lakhs
Estimated cost
Bid Submission
09 Oct 2026
16 days left
EMD
86000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alwar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No. Old-60/F (Guard House) At Jp Line And Office Complex & Stores Including Toilets In Bldg Nos. P-34 & P-35 (Main Office) Of Aro And Provn Of Boundary Wall Near Bldg No. P-436 At Mil Stn Alwar
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick/stone masonry built in cement/lime mortar of any mix, including quoins, pillars, ashlar masonry and removal of debris, complete all as specified and directed. |
| 2 | M&L for brickwork with fly ash bricks conforming to IS 13757 (old size bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 3 | M&L for half-brick thick brickwork with fly ash bricks, straight or curved on plan to any radius, built in cement mortar 1:4, complete all as specified and directed. |
| 4 | Demolition of unreinforced cement concrete in ground floor and paving, not exceeding 15 cm thickness, below or above ground level, including removal of rubbish, complete all as specified and directed. |
| 5 | M&L for PCC 1:2:4 Type B-1 using 20 mm graded stone aggregate, 25 mm thick, as in sub-base, complete all as specified and directed. |
| 6 | Dismantling floor, hearth or wall tiling including cement mortar bedding but excluding backing, removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 7 | M&L for non-skid coloured ceramic tiles 300 x 300 x 7 mm thick in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed. |
| 8 | M&L for polished coloured vitrified ceramic tiles 10 mm thick, square/rectangular, light shade as approved, area of each tile not exceeding 0.36 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed. |
| 9 | M&L for glazed coloured ceramic tiles 450 x 300 x 7 mm thick in vertical surfaces, set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade, over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed. |
| 10 | M&L for polished coloured vitrified ceramic tiles 10 mm thick, square/rectangular, light shade as approved, area of each tile not exceeding 0.36 Sqm, in walls, dado, skirting etc., set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade, over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed. |
| 11 | M&L for 20 mm thick machine-cut granite tiles of approved type/shade, bedded and jointed with grey cement slurry and pointed with white cement admixed with pigment to match the shade, including cutting and polishing, over and including 20 mm thick screed bed in cement mortar 1:6, complete all as specified and directed. |
| 12 | M&L for machine-cut Kota stone slab flooring 18-20 mm thick over and including 20 mm thick screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade, including rubbing and polishing, complete all as specified and directed. |
| 13 | M&L for machine-cut Kota stone slabs 18-20 mm thick in steps, risers, dado, skirting, walls etc., over and including 20 mm thick screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade, including rubbing and polishing, complete all as specified and directed. |
| 14 | M&L for 75 mm thick PCC 1:3:6 Type C-1 using 20 mm graded stone aggregate as in plinth protection, finished fair and even, complete all as specified and directed. |
| 15 | Demolition of unreinforced cement concrete in ground floor and paving exceeding 15 cm thickness above ground level, including removal of rubbish, complete all as specified and directed. |
| 16 | M&L for 60 mm thick machine-pressed precast concrete interlocking paver blocks with grey cement and pigment, any approved shape and size, conforming to IS 15658, M-35 grade, laid over and including 25 mm thick sand bed, complete all as specified and directed. |
| 17 | M&L for 75 mm thick PCC 1:4:8 Type D-2 using 40 mm graded aggregate as sub-base of path/hardstanding, complete all as specified and directed. |
| 18 | Dismantling kerb stones including cement mortar bedding and removal of rubble, complete all as specified and directed. |
| 19 | M&L for factory-made precast cement concrete solid blocks in PCC 1:2:4 Type B-1 using 20 mm graded crushed stone aggregate, of required size, set in cement mortar 1:6, complete all as specified and directed. |
| 20 | Taking down cement plaster/cement lime plaster from PCC, stone or brick surfaces, including raking out joints, hacking for key and scrubbing down with water, complete all as specified and directed. |
| 21 | M&L for rendering 10 mm thick in cement mortar 1:6 on fair faces of stone masonry or concrete surfaces of walls, finished even and smooth without using extra cement, complete all as specified and directed. |
| 22 | M&L for rendering 15 mm thick in cement mortar 1:4 on stone wall surfaces or surfaces other than fair faces of brickwork, finished even and smooth without using extra cement, including integral waterproofing compound measured and paid separately, complete all as specified and directed. |
| 23 | Supply only integral waterproofing compound of approved make and quality, complete as specified and directed. |
| 24 | M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceilings, finished even and smooth without using extra cement, complete all as specified and directed. |
| 25 | M&L for rough-cast plaster on exterior walls comprising undercoat of cement and sand mortar 1:3 not less than 10 mm thick and, while in plastic state, application of rough-cast mixture consisting of crushed stone/fine gravel aggregate 6-12 mm size, coarse sand and cement in the ratio 1:1:1, finished even, complete all as specified and directed. |
| 26 | M&L for preparation of new surfaces and applying two coats of 100% premium acrylic exterior emulsion paint conforming to IS 15489, VOC less than 50 gm/litre, UV, alkali, fungal and dirt resistant, of approved shade, with silicon additives @ 1.43 litre/10 Sqm, over and including one coat exterior primer @ 0.90 litre/10 Sqm and 1 mm thick wall-care putty over prepared surface to achieve an even and smooth finish, complete all as specified and directed. |
| 27 | M&L for preparing newly plastered surfaces and applying two coats of oil bound distemper of approved shade over and including 2 mm thick wall-care putty to obtain an even and smooth surface, complete all as specified and directed. |
| 28 | M&L for preparation of new plastered/unplastered ceiling surfaces and applying three coats of whitewash, complete all as specified and directed. |
| 29 | M&L for preparation of old decorated/plastered wall surfaces including cornices, pilasters etc. and applying one coat of whitewash, complete all as specified and directed. |
| 30 | M&L for complete removal of existing treatment from stone/plastered wall surfaces and applying two coats of 100% premium acrylic exterior emulsion paint conforming to IS 15489, VOC less than 50 gm/litre, UV, alkali, fungal and dirt resistant, of approved shade, with silicon additives @ 1.43 litre/10 Sqm, over and including exterior primer @ 0.90 litre/10 Sqm and 1 mm thick wall-care putty over prepared surface, complete all as specified and directed. |
| 31 | M&L for complete removal of existing treatment from old wall surfaces including cornices, pilasters and other wall features by washing and rubbing down, and applying two coats of oil bound distemper of approved shade over and including 1 mm thick wall-care putty, complete all as specified and directed. |
| 32 | M&L for preparation of old plastered ceiling surfaces and applying one coat of whitewash, complete all as specified and directed. |
| 33 | Taking down chowkatts/frames with shutters, without taking shutters off the frame, not exceeding 1.50 Sqm each, and removing to store, complete all as specified and directed. |
| 34 | Taking down chowkatts/frames with shutters, without taking shutters off the frame, exceeding 1.50 Sqm but not exceeding 4.00 Sqm each, and removing to store, complete all as specified and directed. |
| 35 | Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and removing to store, complete all as specified and directed. |
| 36 | S&F 35 mm thick second-class hardwood factory-made panelled door shutter, two-panel type, with lock rail and 9 mm BWP commercial plywood or 12 mm veneered particle-board panels with commercial veneering on both faces, rails and stiles conforming to IS 1003 (Part I), kiln seasoned and chemically pressure treated, fixed to chowkatts, complete all as specified and directed. |
| 37 | S&F 35 mm thick second-class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass/gauze etc., without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members as specified in SSR Part I Section 8 Clause 8.24(a), supplied and fixed to chowkatts, complete all as specified and directed. |
| 38 | M&L for solid PVC door frame 50 x 47 mm made out of 5 mm plain coloured PVC sheet reinforced with MS square tube, supplied and fixed in openings complete as per manufacturer's specifications/drawings and as directed. |
| 39 | M&L for factory-made solid-panel PVC door shutter 30 mm thick comprising MS tube framework for top and bottom rails covered with heat-moulded plain coloured PVC C-channel, PVC sheet strips, lock rail and panels, assembled with suitable PVC beading and solvent cement and fixed to frame, complete all as specified and directed. |
| 40 | M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of pink primer, complete all as specified and directed. |
| 41 | M&L for preparation of old wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint of approved shade, complete all as specified and directed. |
| 42 | S&F galvanised mild steel wire cloth, 0.56 mm nominal dia wire and average aperture width 1.18 mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed. |
| 43 | S&F cold-rolled mild steel butt hinges 100 mm long, medium weight, complete all as specified and directed. |
| 44 | S&F anodised aluminium barrel tower bolts 150 mm long of extruded section, fixed complete all as specified and directed. |
| 45 | S&F anodised aluminium cast-type handles 150 mm long, fixed complete all as specified and directed. |
| 46 | S&F anodised aluminium alloy sliding door bolt 300 mm long with hasp and staple, fixing clips, fixing bolts and sliding bolt of sheet/cast/extruded aluminium alloy sections, complete all as specified and directed. |
| 47 | S&F in repair stainless steel drapery rod 25 mm dia in lengths directed, of approved finish, including decorative bowls at both ends and pair of powder-coated stainless steel brackets fixed to walls/beams with PVC Rawl plugs and steel screws, complete all as specified and directed. |
| 48 | S&F 300 mm helical/rat-tail door spring with MS sheet wing pattern including roller plate, complete all as specified and directed. |
| 49 | M&L for preparation of old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of red oxide primer, complete all as specified and directed. |
| 50 | Dismantling framed timber scantlings 40 Sqcm and over in section in any position, complete all as specified and directed. |
| 51 | S&F MS steel work in tubular trusses, tubular posts, purlins and rafters including specially shaped washers etc., butt welded, using RHS/SHS conforming to IS 4923, complete all as specified and directed. |
| 52 | M&L for framed steel work as in doors/gates of angle or other sections with gusset plates, rails and braces, drilled for fixing steel sheeting/covering and prepared for hanging/sliding, including hooks and hinges or steel hanging-door fittings, fastening and fixing and making good floor in PCC 1:2:4 Type B-0 to match existing, using Fe-410 Grade E250 Quality A steel, excluding steel sheeting/covering, running rails and guides, complete all as specified and directed. |
| 53 | M&L for flat iron holdfast 25 x 6 mm welded to angle iron door frame, complete all as specified and directed. |
| 54 | M&L for plain/chequered steel plates and channels, square cut or notched, including ordinary/countersunk holes but without attachments, Fe-410W Grade E250 Quality B, complete all as specified and directed. |
| 55 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of red oxide primer, complete all as specified and directed. |
| 56 | Dismantling asbestos cement corrugated/semi-corrugated sheets from roof coverings, complete all as specified and directed. |
| 57 | S&F pre-painted Galvalume aluminium-zinc coated GI-based corrugated steel sheets 0.50 mm thick, approved colour, tensile strength 550 MPa, as roof covering/wall cladding, fixed with self-tapping screws etc., complete all as specified and directed. |
| 58 | M&L for pre-painted Galvalume aluminium-zinc coated GI-based plain steel sheet, 0.50 mm thick, green colour, having minimum tensile strength 550 MPa, as in roof covering, wall cladding and eaves board, fixed with suitable self-tapping screws and wind ties, including necessary fixing accessories, complete all as specified and directed. |
| 59 | S&F anodised aluminium frames and other sections for doors, windows, ventilators and partitions, powder coated in approved colour with powder-coating thickness not less than 50 microns, with one or more rebates including joining cleats and fixing accessories, complete all as specified and directed. |
| 60 | S&F anodised aluminium window/door/ventilator shutters, side-hung type without sash bars, aluminium sections weighing 0.55 Kg/RM, powder coated in approved colour with coating thickness not less than 50 microns, including joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, peg stay 150 mm long, B-21 hinges 100 mm long and suitable handle, complete all as specified and directed. |
| 61 | S&F powder-coated anodised aluminium grill of approved pattern for windows, ventilators and doors, powder-coating thickness not less than 50 microns, complete all as specified and directed. |
| 62 | S&F stainless steel wire cloth of 0.36 mm nominal dia wire and average aperture width 1.40 mm, fixed with stainless steel wire staples, complete all as specified and directed. |
| 63 | S&F ordinary quality sheet glass 4.80 mm thick in squares not exceeding 0.50 Sqm each, complete all as specified and directed. |
| 64 | Taking up or down 15 mm steel tubing and connections including cleaning for refixing or removal to store, complete all as specified and directed. |
| 65 | Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal to store, complete all as specified and directed. |
| 66 | S&F medium-grade steel tubing 15 mm bore with all fittings, fixed to walls and/or laid in floors, complete all as specified and directed. |
| 67 | S&F medium-grade steel tubing 20 mm bore with all fittings, fixed to walls and/or laid in floors, complete all as specified and directed. |
| 68 | S&F in repair rotational-moulded polyethylene water storage tank, white, cylindrical vertical closed-top type, 500 litres capacity, including dismantling existing water tank, removing to store, hoisting and fixing new tank in position, complete all as specified in SSR Part I and as directed. |
| 69 | S&F in repair high-pressure PTMT ball valve 20 mm dia with epoxy-coated aluminium rod and high-density plastic ball, minimum weight 210 grams, screwed for iron pipe and fixed, including taking down existing ball valve of any type, complete all as specified and directed. |
| 70 | S&F brass/gunmetal globe or gate valve 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 71 | S&F in repair white vitreous china squatting pan, Orissa pattern, 580 x 440 mm with integral footrests, including connection to trap and flushing pipe and making good floor, complete all as specified and directed. |
| 72 | S&F in repair white vitreous china wash-down WC pan, pedestal pattern, including connections to drain/outgoing pipe, flushing pipe and anti-syphonage pipe, with white plastic WC seat and cover and CP/aluminised hinging device, complete all as specified and directed. |
| 73 | S&F in repair white vitreous china wash basin 550 x 400 mm, ISI marked, flat-back/angle-back type, excluding taps, waste chain and plug but including CI brackets and cutting/pinning ends of brackets or erecting stand, complete all as specified and directed. |
| 74 | S&F in repair white PVC low-level flushing cistern 10 litres capacity, ISI marked, syphonic action type, including inlet ball valve, float, handle, brackets and 32 mm dia LDPE/HDPE/PVC flush pipe, complete all as specified and directed. |
| 75 | S&F in repair stainless steel sink with draining board fabricated from 1 mm thick sheet, overall minimum size 915 x 460 mm with bowl 410 x 330 x 160 mm, including plug, washers, waste pipe, CI cantilever brackets and connecting union, complete all as specified and directed. |
| 76 | S&F in repair PVC connection 15 mm bore, 450 mm long, with two PTMT nuts, fixed between pillar tap and stop cock/iron pipe, complete all as specified and directed. |
| 77 | S&F in repair MS chromium-plated grating 100 mm dia, with or without hole for waste pipe, including fixing with cement mortar to floor/Nahani trap, complete all as specified and directed. |
| 78 | S&F in repair 15 mm dia fancy type cast copper alloy chromium-plated bib tap with crutch/butterfly handle, screwed down and screwed for iron pipe/brass ferrule, Jaquar OPP-15037PM or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 79 | S&F in repair 15 mm dia CP long-body pillar tap, fancy type, chromium plated, high pressure, with single-lever handle, long screwed shank and fly nuts, Jaquar OPP-CHR-15001PM or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 80 | S&F in repair 15 mm dia stop/angle valve with wall flange, fancy type, chromium plated, high pressure, with crutch/butterfly handle and screwed connections, Jaquar OPP-15053PM or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 81 | S&F in repair PTMT towel rail 600 mm long, minimum weight 190 grams, including CP brass screws and wooden/plastic cleats, complete all as specified and directed. |
| 82 | S&F in repair looking mirror 600 x 450 mm, bevelled-edge selected quality glass 5.5 mm thick, mounted on 6 mm thick commercial plywood with aluminium frame, fixed to wooden plugs with CP brass screws and cup washers, complete all as specified and directed. |
| 83 | S&F in repair brass chromium-plated wall mixer for mixing hot and cold water, screwed for 15 mm bore iron pipe and fixed, complete all as specified and directed. |
| 84 | S&F in repair hand spray/health faucet with lever control and flow rate 3.78 LPM at 3 bar pressure, Jaquar ALD-CHR-573GD or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 85 | S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints, laid in trenches or floors, complete all as specified and directed. |
| 86 | S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed. |
| 87 | S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints, fixed to walls/floors, complete all as specified and directed. |
| 88 | S&F in repair PVC (SWR) bends of any radius, 110 mm bore, complete all as specified and directed. |
| 89 | S&F PVC (SWR) vent cowl 110 mm bore, complete all as specified and directed. |
| 90 | S&F in repair 75 mm dia PVC (SWR) plain floor trap with grating, including jointing with solvent cement, complete all as specified and directed. |
| 91 | S&F in repair PVC (SWR) gully trap 125/110 mm, including setting and jointing with solvent cement, complete all as specified and directed. |
| 92 | S&F in repair PVC (SWR) 110 mm single junction (single Tee), equal or unequal, complete all as specified and directed. |
| 93 | M&L for writing letters or figures, block/Roman/italic/Indian letters not exceeding 30 cm high, complete all as specified and directed. |
| 94 | S&F in repair fancy-type chromium-plated shower rose 125 mm size, with or without swivel joint, including fixing to steel pipe/union, Jaquar OHS-CHR-1663 or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 95 | Dismantling wall and ceiling boards including fibre, pulp, insulation and AC boards/slabs/blankets of any thickness, including cover fillets and removing from site, complete all as specified and directed. |
| 96 | M&L for false ceiling complete with ArmGyp-FB ceiling tiles 595 x 595 mm, approved by GE, fixed with galvanised iron powder-coated inverted T/L sections forming concealed GI framework suspended from ceiling, including 4 mm dia galvanised wire, wall tapping screws, butterfly clips and hold-down clips; main Tee 39 x 24.4 x 0.8 mm, wall angle 22.2 x 22.2 x 0.65 mm and grid 0.61 x 0.61 m, complete as per manufacturer's instructions and as specified and directed. |
| 97 | Demolition of mud in roofs of any thickness including plastering/existing treatment, cleaning and preparation for further treatment and disposal of debris/rubbish to a distance exceeding 1 Km but not exceeding 1.5 Km, complete all as specified and directed. |
| 98 | M&L for PCC 1:2:4 Type B-0 using 12.5 mm graded crushed stone aggregate as roof padding, laid to minimum consolidated thickness 25 mm as levelling course and compacted to minimum slope 1:30, complete all as specified and directed. |
| 99 | M&L for 15 mm thick cement mortar 1:4 screed with waterproofing compound over green concrete surface, finished even and smooth without using extra lime/cement; waterproofing compound measured and paid separately, complete all as specified and directed. |
| 100 | M&L for applying evenly tack coat of industrial bitumen 85/25 @ 1.20 Kg/Sqm, including cleaning surface over bituminous primer, complete all as specified and directed. |
| 101 | M&L for APP-based polymeric waterproofing membrane, minimum weight 3 Kg/Sqm and minimum 3 mm thick, reinforced with polyester non-woven fabric weighing not less than 150 gm/Sqm, laid on primed surface by torch/forced application, complete all as specified and directed. |
| 102 | M&L for PCC 1:4:8 Type D-2 using 40 mm graded stone aggregate as bed concrete for 150 mm bore drain pipe, including packing under and haunching against sides of pipe after laying and testing, complete all as specified and directed. |
| 103 | M&L for 150 mm dia reinforced cement concrete pipes, Class NP2, laid and jointed complete with collars, complete all as specified and directed. |
| 104 | Excavation in trenches not exceeding 1.50 m wide and 1.50 m deep for foundations etc., and getting out in soft/loose soil, complete all as specified and directed. |
| 105 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed. |
| 106 | Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.50 m above starting point, complete all as specified and directed. |
| 107 | M&L for PCC 1:4:8 Type D-2 using 40 mm graded stone aggregate in foundations, filling and mass concrete, complete all as specified and directed. |
| 108 | M&L for PCC 1:3:6 Type C-2 using 20 mm graded stone aggregate in roof kerbs, rounded/chamfered edges and benching to manholes, complete all as specified and directed. |
| 109 | M&L for precast cement concrete 1:2:4 Type B-1 using 20 mm graded stone aggregate, set in cement mortar 1:6, as coping to brick masonry walls, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders, corbels, brackets etc., including weathering, rounded/chamfered angles, throating and necessary formwork, complete all as specified and directed. |
| 110 | M&L for precast cement concrete louvres/jallies 25 mm thick, measured solid, including mouldings but excluding frame, set in cement mortar 1:4, PCC Type B-0 1:2:4 using 12.5 mm aggregate, complete all as specified and directed. |
| 111 | S&F 50 mm thick steel fibre reinforced concrete (SFRC) manhole cover with iron frame, medium duty, conforming to IS 12592, minimum load-bearing capacity 3 tonnes/Sqm, square/rectangular/circular as required, complete all as specified and directed. |
| 112 | Removing building materials to a total distance up to 1.00 Km beyond the lead included in respective rates, including loading, unloading and stacking at destination, complete all as specified and directed. |
| 113 | M&L for broken stone hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 114 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified and directed. |
| 115 | Demolition of reinforced cement concrete roofs, floors other than ground floors, beams, staircases, landings, chajjas and similar suspended work, complete all as specified and directed. |
| 116 | M&L for RCC nominal mix Type B-1, 1:2:4 using 20 mm graded crushed stone aggregate, in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like, complete all as specified and directed. |
| 117 | M&L for TMT reinforcement bars 10 mm dia and over, cut to required length and bent to shape including cranking, spiral bending for column hoops, hooking ends and binding with annealed MS wire not less than 0.90 mm dia or securing with clips, complete all as specified and directed. |
| 118 | M&L for 50 mm thick sandstone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc., not exceeding 2 m length, punched dressed on exposed face and edges, self-faced on other side and set and pointed in cement mortar 1:4, complete all as specified and directed. |
| 119 | M&L for cutting out cracks to V-section in existing roofs/terracing, cleaning, wetting and grouting with cement and sand slurry 1:3, complete all as specified and directed. |
| 120 | S&F factory-made single-extruded WPC solid door/window/clerestory window frames/chowkatts 65 x 100 mm comprising virgin PVC polymer K-value 58-60, calcium carbonate, natural fibres and non-toxic additives, minimum density 750 Kg/Cum, screw withdrawal strength 2200 N face and 1100 N edge, minimum compressive strength 58 N/Sqmm, modulus of elasticity 900 N/Sqmm, Class-A resistance to spread of flame, termite/borer proof, water/moisture proof and fire retardant, fabricated with mitre joints and fixed with MS holdfasts/lugs or SS dash fasteners, complete all as specified and directed. |
| 121 | S&F factory-made single-extruded WPC solid decorative flush door shutter 30 mm thick comprising virgin polymer K-value 58-60, calcium carbonate, natural fibres and non-toxic additives, minimum density 650 Kg/Cum, screw withdrawal strength 1800 N face and 900 N edge, minimum compressive strength 50 N/Sqmm, modulus of elasticity 850 N/Sqmm, Class-A resistance to spread of flame, termite/borer proof, water/moisture proof and fire retardant, laminated with PVC foil of approved design on both faces and fixed with stainless steel butt hinges and SS screws; hinges measured and paid separately, complete all as specified and directed. |
| 122 | S&F stainless steel hinge-pin butt hinges 100 mm long, complete all as specified and directed. |
| 123 | S&F in repair stainless steel sliding door bolt 300 mm long with hasp and staple, bolt not less than 12 mm dia, including minimum six bolts and nuts, four on plate and two on staple, fixing clips and accessories, complete all as specified and directed. |
| 124 | S&F stainless steel barrel tower bolts of extruded section, 150 mm long, fixed complete all as specified and directed. |
| 125 | S&F stainless steel alloy handles 125 mm size, fabricated type, anodised/approved finish, ISI marked, complete all as specified and directed. |
| 126 | S&F stainless steel bow handle 150 mm size, oval type, stove-enamelled black, complete all as specified and directed. |
| 127 | S&F steel ventilator with top-hung shutter including hinges, steel peg stay and necessary fittings, including taking down existing ventilator, complete all as specified and directed. |
| 128 | Cutting holes in brick/stone walls not exceeding half-brick thickness, built in cement mortar, for inserting holdfasts and making good disturbed portions in cement mortar 1:3 or PCC 1:2:4 Type B-1 as required, complete all as specified and directed. |
| 129 | S&F solid PVC wall lining consisting of 5 mm thick decorative coloured laminated PVC sheet including solvent cement, fixed at site on PVC frame as per specifications/drawings, complete all as specified and directed. |
| 130 | S&F 5 mm thick PVC sheet fillet 35 mm wide for wall panelling, including fixing to wall to form PVC framework as per specifications/drawings, complete all as specified and directed. |
| 131 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 132 | S&F MS framework such as grills, gratings, angle frames, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, water-tank framework, cooler stands and similar work, with ends of bars shouldered/riveted or forged into spikes as applicable, conforming to Fe-290 Grade E-165, complete all as specified and directed. |
| 133 | M&L for flat iron as in clamps, holdfasts, wall ties, fan hooks, plain angle cleats for securing purlins to timber trusses/rafters, hooks and cleats welded to angle-iron door/window frames etc., complete all as specified and directed. |
| 134 | M&L for preparation of old painted steel/iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of approved shade, complete all as specified and directed. |
| 135 | Cutting chases, pinning in, making good facing where required and pointing in cement mortar 1:3 for concealed water tubing in brick walls, cutting not exceeding 10 cm girth, complete all as specified and directed. |
| 136 | S&F in repair white glazed vitreous china under-counter oval wash basin 560 x 430 x 195 mm, Jaquar FLS-WHT-5701 or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 137 | S&F in repair soap dispenser with metallic bottle, Jaquar ACN-CHR-1135N or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 138 | S&F in repair white ceramic vitreous china floor-mounted rimless single-piece WC, size 370 x 690 x 750 mm, S-trap 300 mm, including PP soft-close slim seat cover, hinges, dual-flush cistern fittings, fixing accessories and accessory set, Jaquar CNS-WHT-757NS300SPPSZ or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 139 | S&F in repair toilet paper roll holder with flap, Jaquar ACN-CHR-1153S or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 140 | S&F in repair vitreous china half-stall urinal, back-inlet and flat-back type, size 385 x 325 x 635 mm, including plugs, bedding against wall in cement mortar 1:2, 60 mm long brass screws, pointing around back, automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, Jaquar URS-WHT-13253N or equivalent approved make, complete all as specified and directed. |
| 141 | S&F in repair CP brass towel ring, Jaquar ACN-CHR-1121N or equivalent approved make, with 10-year warranty, complete all as specified and directed. |
| 142 | S&F brass CP fancy wall mixer with L-bends including provision for overhead shower and hand shower, for mixing hot and cold water, screwed for 15 mm bore iron pipe, including hand shower and flexible tube, Jaquar COP-CHR-273N or equivalent approved make such as Kohler/Marc, complete all as specified and directed. |
| 143 | M&L for cutting into existing manhole/septic tank for connecting new 100 mm bore drain pipe, including making good around pipe, rendering, cutting out existing benching, forming branch channel of half-round/three-quarter section in PCC 1:2:4 Type B-1, smooth finishing and reforming benching as required, complete all as specified and directed. |
| 144 | M&L for providing precast cement concrete louvres and jallies, 25 mm thick (measured solid), in cement concrete Type B0 (1:2:4) using 12.5 mm graded aggregate, including all mouldings but excluding frame, complete all as specified and directed. |
| 145 | M&L for cement concrete Type B2 (1:2:4), 40 mm graded aggregate, in walls or retaining walls, any thickness, size or shape, including pilasters, buttresses, columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified and directed. |
| 146 | M&L for preparation of new plastered wall surfaces by brooming down/wire brushing, scraping and complete removal of existing treatment, making good minor defects, applying chalk whiting as preparatory treatment and applying two coats of cement paint, white or tinted, complete all as specified and directed. |
| 147 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc., disconnecting and removing materials to store for safe custody or for taking credit as applicable, including making good disturbed surfaces of walls, floors, ceilings etc., complete all as specified and directed. Note: Credit for retrieved materials shall be made separately as per Schedule of Credit. |
| 148 | M&L for concealed point wiring with 1100 Volt grade, 1.5 Sqmm PVC insulated FRLS unsheathed multistranded copper conductor cable conforming to IS 694 and ISI marked, drawn in and including electrical grade PVC conduit of suitable size with all accessories in walls/ceilings/floors/roofs, sunk pressed steel/cast iron terminal boxes with 3 mm thick plastic laminated sheet top cover, including 1.5 Sqmm FRLS multistranded copper conductor earth wire connected to common earth dolly, complete all as specified and directed, for one light/fan point controlled by one switch. |
| 149 | All as per preceding point wiring item, for one 3-pin 5/6 Amp socket outlet on independent board, complete all as specified and directed. |
| 150 | All as per preceding point wiring item, for one 3-pin 5/6 Amp socket outlet on the same board, complete all as specified and directed. |
| 151 | All as per preceding point wiring item, for one bell/buzzer point controlled by one independent push button, complete all as specified and directed. |
| 152 | M&L for concealed point wiring complete for one 15/16 Amp socket outlet on independent board with FRLS PVC insulated unsheathed 2.5 Sqmm multistranded copper conductor single-core cable conforming to IS 694, drawn in and including PVC conduit of suitable size and accessories, factory-made pressed steel terminal box n less than 2 mm thick, painted internally and externally with two coats synthetic enamel over red oxide primer, 3 mm thick plastic laminated sheet top cover and 2.5 Sqmm green FRLS copper earth continuity conductor drawn in same conduit and connected to common earth/earth dolly, including one 15/16 Amp switch, complete all as specified and directed. |
| 153 | M&L for concealed point wiring complete for one 15/16 Amp socket outlet on independent board with FRLS PVC insulated unsheathed 4 Sqmm multistranded copper conductor single-core cable conforming to IS 694, drawn in and including PVC conduit of suitable size and accessories, factory-made pressed steel terminal box n less than 2 mm thick, painted internally and externally with two coats synthetic enamel over red oxide primer, 3 mm thick plastic laminated sheet top cover and 4 Sqmm green FRLS copper earth continuity conductor drawn in same conduit and connected to common earth/earth dolly, including one 15/16 Amp switch, complete all as specified and directed. |
| 154 | S&F ceiling fan regulator, electronic step type, suitable for 230 Volts single-phase supply, including connections and fixing, complete all as specified and directed. |
| 155 | Taking down sub-main wiring cable of any number of runs along with earth wire from existing concealed/surface conduit, including disconnecting and removing cable and offering credit as per Schedule of Credit, complete all as specified and directed. Note: Any number of runs of cable together with earth wire shall be measured as one unit length. |
| 156 | M&L for sub-main wiring with four runs of 6 Sqmm single-core PVC insulated copper conductor cable and one run of 6 Sqmm single-core PVC insulated copper conductor cable as earth continuity conductor, drawn through existing/provided PVC conduit, including connections and testing, complete all as specified and directed. Note: Four runs of 6 Sqmm cable together with one run of 6 Sqmm earth conductor shall be measured as one unit length. |
| 157 | S&F in repair piano type switch, 6 Amp, one-way, flush type, ISI marked, including connections and fixing, complete all as specified and directed. |
| 158 | S&F in repair bell push, 5/6 Amp, flush type, ISI marked, including connections and fixing, complete all as specified and directed. |
| 159 | S&F in repair socket outlet suitable for 2/3-pin plug, 5/6 Amp, flush type, 230 Volts, including taking down existing unserviceable socket of any type and connecting up, complete all as specified and directed. |
| 160 | S&F switch-socket combination outlet, 3-pin, 6/16 Amp, flush type, multipurpose, with fuse and neon indicator, ISI marked, including connections and fixing, complete all as specified and directed. |
| 161 | S&F surface type ceiling rose, Bakelite/PVC/polycarbonate, size 65 x 50 mm, three terminal, including connections and fixing, complete all as specified and directed. |
| 162 | S&F inverter rechargeable LED batten light complete with fixture, 3 feet long, 1 x 20 Watt AC, energy-saving type, backup up to 4 hours, lithium battery minimum 5600 mAh, battery life 500 or more recharge cycles and charging time 8-10 hours, including connecting with three-core flexible copper conductor cable of suitable size from ceiling rose and fixing complete. Make: Halonix/Havells/Philips/Wipro or equivalent approved make. |
| 163 | S&F in repair 10 Watt B-22 inverter rechargeable LED T-bulb suitable for 230 Volts AC supply, including necessary connections and fixing, complete all as specified and directed. Make: Philips/Halonix/Havells/Wipro or equivalent approved make. |
| 164 | S&F PVC/polycarbonate batten holder with cord grip cap suitable for pendant fitting, ISI marked, including connections and fixing, complete all as specified and directed. |
| 165 | M&L for taking down and refixing existing ceiling fan of 1200/1400 mm sweep, including repair/rewinding where required with super-enamelled copper winding wire of existing gauge, necessary insulation, varnishing, assembling, testing and putting into satisfactory working condition, complete all as specified and directed. |
| 166 | S&F in repair MCB distribution board, TPN, 8-way, double-door type, suitable for 415 Volts supply, including bus bars, neutral link, earth bar, DIN channel, internal interconnections, fixing and connections, complete all as specified and directed. |
| 167 | S&F in repair MCB distribution board, SPN, 8-way, double-door type, suitable for 240 Volts supply, with 200 Amp rated bus bar, neutral link, earth bar, DIN channel, internal interconnections, fixing and connections, complete all as specified and directed. |
| 168 | S&F in repair TPN MCB, 63 Amp, 10 kA breaking capacity, suitable for 415 Volts, 3-phase supply, including connections and fixing in existing DB/panel, complete all as specified and directed. |
| 169 | S&F in repair SPN MCB, 40 Amp, 230 Volts, single-phase, 10 kA breaking capacity, including connections and fixing in existing DB/panel, complete all as specified and directed. |
| 170 | S&F in repair SP MCB, 6 to 40 Amp, 230 Volts, single-phase, 10 kA breaking capacity, including connections and fixing in existing DB/panel, complete all as specified and directed. |
| 171 | S&F in repair electric bell, multi-music type, suitable for 230 Volts AC supply, including necessary connections and fixing, complete all as specified and directed. |
| 172 | M&L for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm thick buried directly in earth pit n less than 2.25 m deep, top edge of plate n less than 1.50 m below normal ground level, connected with 4 mm dia GI wire as earth lead using GI/steel bolts, nuts, check nuts and washers and welding at joints, including excavation and earthwork, 15 mm bore light grade GI protective pipe, GI/steel earth test point 75 x 75 x 25 mm, charcoal dust, common salt, PCC 1:2:4 Type B-1 chamber, MS angle iron frame 40 x 40 x 3 mm, 40 mm thick RCC cover Type B-1 reinforced with 6 mm dia bars @ 75 mm c/c both ways, 12 mm dia MS lifting handle, GI funnel with wire mesh and 20 mm bore light grade GI watering pipe, complete including connection, testing earth resistance and commissioning, all as specified and directed. |
| 173 | Supply, laying, jointing and testing XLPE insulated, armoured, heavy-duty LT underground electric cable with stranded aluminium conductor, 1100 Volt grade, 95 Sqmm, 3.5 core, laid in trenches/ducts, through pipes, under floors/roads or along poles, including uncoiling, laying, dressing and testing, complete all as specified and directed. Note: Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation/earthwork shall be measured and paid separately. |
| 174 | Excavating in trenches n exc 1.50 m wide and n exc 1.50 m deep for underground cables/foundations/shafts/manholes etc., n exc 10 Sqm on plan, and getting out in soft/loose soil, complete all as specified and directed. |
| 175 | Returning, filling in excavated soft/loose soil including spreading, levelling, watering and well ramming in layers n exc 25 cm thick, complete all as specified and directed. |
| 176 | Removing excavated soil/material to a distance n exc 50 metres and depositing where directed at a level n exc 1.50 metres above starting point, complete all as specified and directed. |
| 177 | M&L for brick protection over underground cable with fly ash bricks conforming to IS 13757, old-size bricks, width equal to length of brick, laid dry and flat and abutted with each other with gap between adjacent bricks n exc 10 mm, including taking down existing unserviceable brick protection, complete all as specified and directed. |
| 178 | M&L for dry sand cushioning to underground electric cable with screened and washed sand, including spreading, levelling and punning to provide required cover, complete all as specified and directed. Note: Thickness after punning shall be considered for measurement. |
| 179 | Supply, installation, testing and commissioning of factory-made, CPRI type-test certified LT feeder pillar box (KIOSK), outdoor, platform-mounted type, suitable for 415 Volts, 3-phase and neutral, 4-wire, 50 Hz AC supply, dust and vermin proof with IP-65 protection, fabricated from 3.15 mm thick CRCA MS sheet supported on 40 x 40 x 6 mm angle-iron framework, powder-coated finish, front and rear opening with aprons for cable entry, double-door shutters and locking arrangement including 65 mm Godrej Freedom lock with two keys; complete with 400 Amp insulated copper bus bars n less than 600 mm long mounted on porcelain insulators, internal power/metering wiring with PVC insulated FRLS multistranded copper conductor cable conforming to IS 694 of adequate size but n less than 4 Sqmm, installed with minimum 450 mm clearance above ground and PCC 1:4:8 Type D-2 foundation; Incoming: one No. 250 Amp, 25 kA, 4-pole, 440 Volt MCCB with magnetic setting and thermal release; one multifunction meter Class 1.0 with three-line LCD display, programmable CT ratio -/5A and suitable CTs, capable of indication/recording of current, voltage, PF, active/reactive/apparent power, run hours etc., Make HPL NEMFVIFPPE000 or equivalent L&T/Secure/Conserve; one set 22.5 mm dia LED indication lamps 240 Volts AC for three-phase availability; one set of four Nos. 400 Amp copper bus bars; Outgoing: one No. 160 Amp, 16 kA, 4-pole, 440 Volt fixed-type MCCB and four Nos. 100 Amp, 16 kA, 4-pole, 440 Volt fixed-type MCCBs, including all interconnections, earthing, hardware, labels, supports and accessories, complete all as specified and directed. |
| 180 | S&F LED security light luminaire, Draco Series, 20 Watt, 230 Volts, 50 Hz, including LED module and all necessary fixing accessories and connections, complete all as specified and directed. Make: C&S Cat Part No. LTESS20WLED or equivalent Crompton Greaves/Wipro. |
| 181 | S&F in repair street-light bracket fabricated to required shape and angle from 32 mm dia light-grade GI tubing/suitable size, length n less than 1.00 metre, suitable for fixing/holding security light fitting, including two Nos. MS flat-iron clamps 32 x 3 mm with bolts, nuts and washers and fixing complete all as specified and directed. |
| 182 | S&F LED recessed backlit panel light, 36/40 Watt, square type, size 2 feet x 2 feet, cool-white 6500K, aluminium housing, suitable for false ceiling, including connecting up with three-core flexible copper conductor cable of suitable size from ceiling rose and fixing complete all as specified and directed. Make: Halonix/Havells/Philips/Wipro or equivalent approved make. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysOct 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender