Tender For Special Repairs Of Bldg No P-51 (Cook House) At New Klp Ac Depot, Acc&S Under Ge(N) Ahilyanagar.
Tender Value
42.32 Lakhs
Estimated cost
Bid Submission
08 Oct 2026
4 days left
EMD
85000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmednagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs Of Bldg No P-51 (Cook House) At New Klp Ac Depot, Acc&S Under Ge(N) Ahilyanagar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc.15cm thick below or above ground level. |
| 2 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc. |
| 3 | M&L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed. |
| 4 | M&L for Reinforced cement concrete (design mix) of M20 (20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete |
| 5 | M&L for Mild steel deformed bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 6 | M&L for non skid ceramic coloured tiles 8-10 mm thick as approved by GE (square/rectangular) area of each tile 600x600mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed |
| 7 | M&L for vitrified/ ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm, (600 x 600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 8 | .-Ditto- as per item No 7 above but on skirting and backing coat of 10 mm thick in CM 1:4 |
| 9 | M&L for coloured glazed ceramic tiles 300x450mm, 7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 10 | M&L for non skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 11 | M&L for 18-20mm thick machine cut kota stone slab in flooring,steps over 20 mm thick screed base in cement and sand (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge |
| 12 | M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar including 15 mm thick backing coat in cement and sand mortar (1:4) etc complete all as specified and directed by Engineer-in-Charge. |
| 13 | M&L for 15 -18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick Screed bed etc complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L for Rounding to edges full nosing of stone slabs one edge, such as in steps, cooking platform, and other similar situations completely all as specified and as directed by engineer in charge |
| 15 | M&L for Rounding to edges half nosing of stone slabs one edge, such as in steps, cooking platform, and other similar situations completely all as specified and as directed by engineer in charge |
| 16 | M&L for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge |
| 17 | Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified |
| 18 | M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius, built in CM 1: 6 complete all as specified |
| 19 | M&L for brickwork with subclass ‘B’ bricks half brick thick wall, straight or curved on plan exc 6m mean radius, built in CM 1: 6 complete all as specified. |
| 20 | Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed |
| 21 | M&L for rendering, 15 mm thick on stone/brick / concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed. |
| 22 | M&L for Rendering 10 mm thick on fair faces of brick work or on concrete surfaces in CM 1:6 finished even and fair without using extra cement including sagol finished complete all as specified. |
| 23 | M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed. |
| 24 | M&L for 1 mm wall care putty on walls complete all as specified and directed by Engg-in-charge. |
| 25 | M&L for Preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and Chalk whiting, on plastered surfaces, preparatory to distempering applying two coat oil bound distempering all as specified and directed. |
| 26 | M&L for complete removal of existing treatment, washing, rubbing down and stopping old distempered andapplying two coat of white washing on walls |
| 27 | .-ditto- all as per ser item No 26 above (here-in-before) but on ceiling. |
| 28 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surface. |
| 29 | M&L for preparing new plastered surfaces of walls and apply two coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffolding etc complete all as specified and directed. |
| 30 | .-ditto- all as per ser item No 29 above (here-in-before) but on ceiling. |
| 31 | M&L for preparing old plastered surfaces of walls and apply two coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffolding etc complete all as specified and directed. |
| 32 | .-ditto- all as per ser item No 31 above (here-in-before) but on ceiling. |
| 33 | S&F in repairs wash hand basin with pedestal vitreous China white, flat back or angle type of size 550 X 400 mm incl waste chain and plug and porcelain stopper, waste pipe, a pair of brackets, or erecting stand and PVC connection etc complete all as specified and directed by Engineer-in-Charge |
| 34 | S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply only 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 36 | Taking up or down 15 mm bore steel tubing and connections |
| 37 | .-Ditto- all as per ser item No 36 above but 20 mm bore tubing |
| 38 | Supplying and laying 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified. |
| 39 | .-Ditto. all as per ser item No 38 above but 20 mm bore tubing. |
| 40 | S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified. |
| 41 | S&F in repairs fancy type stop cock/ anglecock/ two way cock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F in repairs bib tap 15 mm dia, fancy type CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 43 | S&F of Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm etc complete all as specified and directed by Engineer-in-Charge. |
| 44 | S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed. |
| 46 | Supply only 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed. |
| 47 | Supply only PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified. |
| 48 | S&F in repairs PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed. |
| 49 | .-Ditto. all as per ser item No 48 above but as in trenches or floor |
| 50 | S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/ floor etc complete all as specifed and directed. |
| 51 | .-Ditto. all as per ser item No 50 above but as in trenches or floor |
| 52 | S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed |
| 53 | S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed |
| 54 | S&F PVC (SWR) vent cowl110mm bore |
| 55 | S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 2000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected including dismantling water tanks and removing to store etc complete all as directed. |
| 56 | Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. |
| 57 | Taking down chowkhats or frames not exc.1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge. |
| 58 | Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge. |
| 59 | S & F pressed steel door frame of size 100 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified. |
| 60 | S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated |
| 61 | S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing |
| 62 | S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing. |
| 63 | S&F in repair Auto closing hinges 35mm of o crank (KH-001) ir 8 crank (KH=002) openable at 110 degree for kitchen cabinet shutters fixed complete as specified and directed Please Enable Macros to View BoQ information |
| 64 | S&F in repair Auto closing hinges 35mm of o crank (KH-001) ir 8 crank (KH=002) openable at 110 degree for kitchen cabinet shutters fixed complete as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender