Tender For Special Repair And Minor Works Under Age B&R-I And Age E&M-Iv Of Ge(S) Bathinda At Bathinda Mil Stn (2Nd Call) (Job No. Sr(B)-12 Of 26-27, Minor-08 Of 26-27, Minor-24 Of 26-27, Minor-07 Of 26-27 And Minor-11 Of 26-27)
Tender Value
46.79 Lakhs
Estimated cost
Bid Submission
01 Oct 2026
13 days left
EMD
93580
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair And Minor Works Under Age B&R-I And Age E&M-Iv Of Ge(S) Bathinda At Bathinda Mil Stn (2Nd Call) (Job No. Sr(B)-12 Of 26-27, Minor-08 Of 26-27, Minor-24 Of 26-27, Minor-07 Of 26-27 And Minor-11 Of 26-27)
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. |
| 2 | M&L half brick brick work with sub class `B' bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:4 etc complete all as specified and as directed. |
| 3 | M&L brick work with sub class `B' bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:6 etc complete all as specified and as directed. |
| 4 | M&L brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:4 but except bricks (old serviceable bricks to be used) complete all as specified and directed.Note : The rate includes for cleaning of old bricks |
| 5 | Demolition of cement concrete (unreinforced) including tiles of any description & terrazzo finish, etc. in ground floors/first floor of any thickness (below or above ground level) complete all as specified and directed. |
| 6 | Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed. |
| 8 | M&L non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed in CM 1:6 and including dismantling of old tiles/terrazzo finish etc, complete all as specified |
| 9 | M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, on vertical surfaces as in skirting etc. set and jointed in neat cement slurry/paste and pointed in white or coloured cement to match over and including 10mm thick plaster in CM 1:4 etc complete all as specified and as directed. |
| 10 | M&L for first quality, scratch free, straight cut/joint free, vitrified pavers for external use, 9-10mm thick, of size 300mm x 300mm, in floors etc over & including 15mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry & pointed with grout of matching shade of tiles, complete. |
| 11 | M&L Granite work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms etc like in cement mortar (1:4) including rounding of / moulding to edgesw (half round) of stone of any description including rubbing and polshing (Granite finish) pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15 mm thick Screed bed or bedding layer in CM 1:4 complete all as specified and directed. |
| 12 | Taking down chowkhats or frame n exc 1.50 Sqm each with shutters (W/out taking off shutters from the frames), etc complete all as specified and as directed. |
| 13 | Taking down chowkhats or frame exc 1.50 Sqm but n exc 4 Sqm each with shutters (W/out taking off shutters from the frames), etc complete all as specified and as directed. |
| 14 | Taking down shutters of any description exc 1 Sqm & nexc 2 Sqm each, etc complete all as specified and as directed. |
| 15 | Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in the same opening including easing and adjusting including renewal of unserviceable screws etc. complete all as specified and directred |
| 16 | Supply and fixing powder coated Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing,handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed . |
| 17 | S & F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 18 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portion) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gap at junctions, ie at top, bottom and sides with required EPDM rubber/neoprene gasket etc. complete all as specified and directed . |
| 19 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or fixed including with beads / fillets complete all as specified and directed. |
| 20 | M&L for preparing of new or previusly untreated painted wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 21 | S & F 2nd class hardwood, 35 mm thick plain framed panelled shutters (any number of panels) with with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both side. The size of rail & stiles as per IS :1003 (Part I), kiln seasoned and chemically preassure treated, etc complete all as specified and as directed. |
| 22 | S & F Mild steel Butt Hinges, 100 mm size, medium weight, cold rolled fixed with screws/welding to wooded/steel frames or chowkats, etc complete all as specified and as directed. |
| 23 | S & F 200 mm aluminium anodised, barrel tower bolts of extruded section etc complete all as specified and as directed. |
| 24 | S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 25 | S&F aluminium handles, cast type anodised 125 mm long complete all as specified and directred |
| 26 | S & F 300mm mild steel ordinary rat tail rod springs, including roller & roller plate, etc complete all as specified and as directed. |
| 27 | S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc 0.50 Sqm in each pane etc complete all as specified and as directed. |
| 28 | S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares n. exc 0.50 Sqm in each pane etc complete all as specified and as directed. |
| 29 | S & F 25mm dia stainless steel drapery rod with bracket incl wall and other side fancy knobs at both ends as approved by Engrineer-in-charge/GE including taking down old existing rod/pelmet with accessories complete all as specified and as directed. |
| 30 | M&L for preparation of new steel and iron surfaces of any description exc 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 31 | S & F in repair 4 lever brass mortise lock, vertical type of size100 mm complete all as specified and directed. |
| 32 | M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. |
| 33 | S&F Door closer hydraulically regulated, aluminium body (extruded section) designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 34 | S&F 12mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including necessary fixing/supporting arrangements like handle, cleats, heavy duty floor spring etc cutting to shape, drilling holes, design, and similar work as required including complete taking down of existing glass handles, hinges complete etc. and also including the firm for logo & sign complete all as specified and directed. Please Enable Macros to View BoQ information |
| 35 | S&F 12mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including necessary fixing/supporting arrangements like handle, cleats, heavy duty floor spring etc cutting to shape, drilling holes, design, and similar work as required including complete taking down of existing glass handles, hinges complete etc. and also including the firm for logo & sign complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender