Tender For Providing Upvc Partition Arrangements And Sink Arrangements In Ground Floor Red, Green Zone Wards In Tirunelveli Medical College Hospital At Tirunelveli
Tender Value
4.14 Lakhs
Estimated cost
Bid Submission
05 Oct 2026
5 days left
EMD
4150
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tirunelveli → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing Upvc Partition Arrangements And Sink Arrangements In Ground Floor Red, Green Zone Wards In Tirunelveli Medical College Hospital At Tirunelveli
BOQ
| Sl. No. | Item Description |
| 1 | Supply and installation of UPVC partitions with doors shall utilize UPVC profile sections with an outer wall thickness of 2.30mm (±0.2mm), featuring an outer frame of 74mm x 60mm x 56mm, a shutter of 104mm x 60mm x 66mm, a mullion of 72mm x 60mm x 36mm, a glazing bead of 35mm x 18mm, a 20mm multi-chambered hollow uPVC panel section of 150mm x 20mm, and a uPVC panel bead of 19mm x 16mm. All profiles of frames, sash, and mullion shall be reinforced, where required, with 1mm thick GI steel sections. The door will be equipped with 3D hinges for enhanced weight holding capacity, and security devices such as multipoint lock systems with a cylinder lock facilitated handle, all compliant with relevant specifications and departmental directives. Glazing or uPVC panels shall be 5mm thick Plain Toughened or uPVC panel grip, held by TPE (Grey) weather-sealed gaskets. All corners and mullion joints of the frame and sash shall be mitred cut and fusion welded without mechanical joints, with all welded joints neatly trimmed to a grooved nib finish, ensuring the finished products are free from sharp edges. The complete units shall be fixed into pre-finished openings by drilling and fastening through the outer frame using high-quality fasteners, and silicon sealant shall be applied to fill the gap between the wall and the frame for a leak- proof installation and completion etc., Complete and as directed by the department officers. |
| 2 | Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam.Installation: The profiles should be cut to length and welded 45 degrees. The window should be desinged such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug. |
| 3 | Supplying and fixing in position best quality approved make Stainless steel sink of size of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works] |
| 4 | Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia “B” class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). |
| 5 | Supplying, laying and jointing CPVC (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Above ground level - EWS |
| 6 | 25mm dia |
| 7 | 20mm dia |
| 8 | Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid. |
| 9 | 50mm dia |
| 10 | Supplying CPVC Specials of SDR 11 Conforming to IS 17546-2021 in water supply arrangements (both in internal and external water supply arrangements Since the labour for cutting, pasting, sundries have already been included under pipe line item of works, no separate provision for fixing PVC specials needs to be allowed. |
| 11 | 25mm dia CPVC Elbow |
| 12 | 20mm dia CPVC Elbow |
| 13 | 25mm dia CPVC Tee |
| 14 | 20mm dia CPVC Tee |
| 15 | 25mm dia CPVC Coupling |
| 16 | 20mm dia CPVC Coupling |
| 17 | Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. |
| 18 | 25mm dia |
| 19 | GST Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender