Tender For Construction Of Sheds 02 Nos. Of Adjacent To The Existing Upper Shed Of Sheet Metal Shop At Hvf, Avadi
Tender Value
68.47 Lakhs
Estimated cost
Bid Submission
01 Oct 2026
0 days left
EMD
1.28 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvallur → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Sheds 02 Nos. Of Adjacent To The Existing Upper Shed Of Sheet Metal Shop At Hvf, Avadi
BOQ
| Sl. No. | Item Description |
| 1 | Grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance not exceeding 50 m and clearing site (girth exceeding 30 cm and not exceeding. 100cm) |
| 2 | Excavating in hard/dense soil in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out. |
| 3 | Earth work excavation in trenches exceeding 1.5m and not exceeding 3.0 m in width and depth and getting out in hard/dense soil. |
| 4 | Demolition of cement Concrete of any description and in any position not otherwise specifically provided for (unreinforced) in of any thickness |
| 5 | M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering |
| 6 | Material and labour for sand filling under floors or in foundation including watering and consolidation. |
| 7 | M & L for P.C.C 1:3:6, C2 type using 40mm graded aggregated in foundation,grouting of steel structures, filling and mass concrete. |
| 8 | M & L for P.C.C type B2 1:2:4 using 40mm graded aggregated in foundation, filling and mass concrete |
| 9 | Supply and fixing of Glass dividing strips, 3mm, 22mm width of strip. |
| 10 | M & L for providing RCC design mix M20 Concrete (1:2:4) in Foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete |
| 11 | M & L for providing RCC design mix M20 Concrete (1:2:4) in Beams, cantilever bressummers, lintels over 1.5m span |
| 12 | M & L for flat Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surface |
| 13 | M & L for flat Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc. also splays between floors and beams for fair finished surface. |
| 14 | Supply and Fixing of mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, Bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 15 | Supply and fixing of mild steel reinforcement TMT bars 8mm dia to 6 mm dia, cut to length, bent to shape required, including cranking, Bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 16 | Material and labour for brick work built in CM 1:6 using sub-class ''B'' bricks ,straight or curved on plain exc 6m mean radius. |
| 17 | M & L for plastering in CM 1:4, 15mm thick on fair faces of brick work and concrete surfaces |
| 18 | Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel,trusses,purlin set manufactured out of minimum 0.75mm thick steel sheet as per design requirements. The Steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550Mpa) conforming to AISI specifications and IBC2009 for cold formed steel framing and construction and also as perIS:875-1987,ISO 800-1984 and IS:801-1975. The wind load shall be as per provisions of IS875(part-III). LGSFS frame shall be designed as per IS:801 using commercially available software such as Frame CADPro-11.7/STAADPRO- V8i/ArchiteKV2.5.16/Revit architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties,Light Duty Hold-ons, Twist Straps(to connect truss with wall frames), Strong Tie,Tie Rod,H-Brackets, Boxing Sections, L Shaped Angles for better structural stability. The framing section shall be cold form C type having minimum web 89mmx39mm flangex11mm lip in required length as per structural design requirement duly punched with dimple/slotat required locations as per approved drawings.The slots will be along center line of webs and shall be spaced minimum 250mm away from both ends of the member .The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self-drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTMB 633(13) or equivalent corrosion protection of gauge 10 & 12,TPI 16 and 8of length 20mm. The frames shall be fixed toRCC slab or Tie beam over Neoprene rubber using self-expanding carbon steel anchor bolt of dia as per approved drawings and design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT. The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above |
| 19 | Supply and fixing of Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping anti corrosive screws as specified. |
| 20 | S &F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping anti corrosive screws as specified . |
| 21 | M & L for painting to steel surfaces of any description, over 10cm in width or girth,with two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer including preparing new surfaces. |
| 22 | Supply & fixing of Steel windows for industrial buildings with centre hung shutters including brass pivots, catch spring and pulley wheel complete |
| 23 | S & F of 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane |
| 24 | S & F of Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops,hand made sliding bolts, etc conforming to Fe.290.Gde-E-165 |
| 25 | S& F of Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W(Gde-E- 250)quality-A |
| 26 | Material and Labour for Distempering on walls (OBD) two coats on newly plastered wall surfaces with priming plastered and other surfaces with alkali resistant priming paint. |
| 27 | Material and Labour for applying two coat of Exterior emulsion on external wall surfaces, priming paint including preparation of new surfaces. (Make:- ASIAN, NEROLAC, BERGER or suitable equivalent make) |
| 28 | Removal of excavated hard materials to a lead exceeding 250 m but not exceeding 500 m and depositing where directed. |
| 29 | Removal of excavated soil material to a lead exceeding 250m but not exceeding 500m and depositing where directed. |
| 30 | Returning, filling in hard/dense soil including spreading, levelling, watering and well ramming in layers not exc 25 cm. |
| 31 | Material and labour for Point wiring with PVC insulated unsheathed single core cable 1100V grade confirming to IS 694 multi strand copper conductor along with 2mm thick Instove enamelled STEEL conduit accessories run on wall or roof including M.S. switch box concealed in the wall(made out of 3mm thick sheet) and laminated sun mica sheet 3mm thick cover for housing the switches, regulators and plug socket etc. mount on a wall/roof etc. including same size copper earth continuity wire. a)one light point or one fan point controlled by one switch with cable 1.5 sqmm size. |
| 32 | Material and labour for Point wiring with PVC insulated unsheathed single core cable 1100V grade confirming to IS 694 multi strand copper conductor along with 2mm thick stove enamelled STEEL conduit accessories run on wall or roof including M.S. switch box concealed in the wall(made out of 3mm thick sheet) and laminated sun mica sheet 3mm thick cover for housing the switches, regulators and plug socket etc. mount on a wall/roof etc. including same size copper earth continuity wire. b)One 3 pin socket outlet 5 amps on the same board with other switches, with cables 2.5 sqmm size. |
| 33 | Material & Labour for 3 phase PVC/ Polycarbonate, isolated ceiling rose 5A, 230V, AC , three terminals. Make: ANCHOR/HAVELLS /KUNDAN or suitable equivalent make. |
| 34 | Material & Labour and connecting to the system flush type switches piano 6A single pole one way (Make:, ANCHOR/HAVELLS /PHILIPS/PANASONIC or suitable equivalent make. |
| 35 | Supply & fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps MCB. (Make: Legrand / Havells /Anchor or suitable equivalent make) |
| 36 | Supply & fixing and connecting to the system of Sheet metal enclosures with double door DB's when MCB'S to be used Triple pole & neutral 8way,415 V with 200 Amps rated busbar, (Make: Legrand/Havells / ABB or suitable equivalent make) |
| 37 | Supply & fixing 415 Volt,10KA 'C' curve MCB of TPN 40 To 100Amps in the MCB DB complete with connection testing and commissioning. (Make :Legrand/ Havells/ C&S or suitable equivalent make) |
| 38 | Supply & fixing 240 Volt,10KA 'C' curve MCB of single pole 6 to 32Amps in the MCB DB complete with connection testing and commissioning. Make Legrand/Havells/C&S or suitable equivalent make |
| 39 | Supply & fixing of sheet metal enclosures for DBs when MCBs to be used Single pole & neutral,8 way double door with 200 amps rated bus bar. |
| 40 | Supply and fixing amp rating 240 V 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 AMP current carrying capacity in the MCB DB complete with connection testing and commissioning. |
| 41 | Supply & Fixing of wiring for circuit/sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in STEEL conduit. a) 2x2.5 sqmm + 1x2.5 sqmm earth wire |
| 42 | Supply & Fixing of wiring for circuit/sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in STEEL conduit. b) 2x1.5 sqmm + 1x1.5 sqmm earth wire |
| 43 | Supply and fixing of exhaust fan, steel body AC single Phase. 230V of size 450 mm sweep heavy duty with blades, and frame and louvers (Make: Almonard/ Khaitan/ Crompton or Suitably equivalent make) |
| 44 | Material & labour for .XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 3.5/ core 35/ sq.mm , U.G. cable with XLPE insulated aluminum conductor. (Make : Havells/Finolex/Orbit /Polycab or Suitably equivalent make ) |
| 45 | Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. (Make: Havells/ Philips/ Wipro/ Bajaj/ CG/ Luker) or suitable equivalent make. |
| 46 | Supply & fixing of galvanised steel tubes, medium grade 25mm dia for ceiling fan down rod. |
| 47 | Supply and fixing LED lights fitting 2x 22W, 220V,AC decorative box type with driver, holder includingLED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make: Havells/ Philips/ Wipro/ Bajaj/ CG or suitable equivalent make. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender