Tender For Special Repairs To Bldg No. T-23 (Or Line) Under The Aor Of Age B/R-I Of Ge (S) Mamun
Tender Value
30.25 Lakhs
Estimated cost
Bid Submission
07 Oct 2026
19 days left
EMD
60500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pathankot → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Bldg No. T-23 (Or Line) Under The Aor Of Age B/R-I Of Ge (S) Mamun
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified & directed. |
| 2 | Demolition of cement concrete (unreinforced) or tiling etc in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed. |
| 3 | Demolition of cement concrete (unreinforced) or tiling etc in roof, floors (other than Ground floors), Beams, staircase, landing, chajjas and similar suspended work complete all as specified & directed. |
| 4 | Demolition of cement concrete (Re-inforced) of any description and in any position not otherwise specifically provided for. |
| 5 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including brushing with neat cement slurry @ 3.0 Kg of cement per Sqm complete all as specified & directed. |
| 6 | Taking down cement plaster/wall tiles including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed |
| 7 | Taking down existing roof treatment of any description incl mud phuksha or PCC pedding if any (any no. of layers) including removal of debries in low laying area exc 1.00 KM but n.exc 2.00KM complete all as specified and directed |
| 8 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each complete all as specified & directed. |
| 9 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each complete all as specified & directed. |
| 10 | Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each and refixing in same opening (incl easing and adhustment and minor repair) complete all as specified & directed. |
| 11 | M&L for Brickwork with Fly Ash Bricks (old size), straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified & directed. |
| 12 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid one side prelam and other plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and crew withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified & directed. |
| 13 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ choowkhat of size 50 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs fasteners shall be paid for separately) complete all as specified & directed. |
| 14 | S&F of 35mm thick single piesce Factory made wire gauge door shutters including of wire cloth (Steel & aluminium XPM) manufacturing by PVC sheets printed 5mm thick on both side on frame made out M.S tube 19 SWG, size 19mm x 19mm complete in all respect with lock rail and beutifed by PVC beading all around fixed with PVC solvent cement complete all as per Drawing No CEPZ/TD-378 Sheet 1/1 dated 27/12/2011 comlete all as specified and as directed. |
| 15 | S&F in repair factory made 25mm (+ 0.7mm) thick WPC cupboard shutter, shelf partitions, prelaminated one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cbm finish at all edges for making edges lipping/bending, complete all as specified and directed. |
| 16 | S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane complete all as specified and directed. |
| 17 | S&F for Hasp and staple 100 mm in size, aluminium anodised,including bolt to hinge plate and fixed with screws complete all as specified & directed. |
| 18 | S&F continuous (piano) hinges, mild steel, bright finish width of flaps (when open) 30 mm complete all as specified & directed. |
| 19 | S&F Stainless steel designer handle (heavy duty) of 100mm size, fixed to drawers or cupboard shutters complete all as specified & directed. |
| 20 | S&F Butt hinges 100 mm long, stainless steel, medium weight and fixed complete all as specified & directed. |
| 21 | M & L for Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed |
| 22 | S&F Aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed complete all as specified and directed. |
| 23 | S&F Aluminium, anodised, barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed. |
| 24 | S&F Aluminium, anodised, handles 125 mm of extruded section and fixed complete all as specified and directed. |
| 25 | S&F floor door stopper of 140mm long cover plate of aluminium alloy body and tongue anodised with hard drawn steel spring, fixed in floor complete all as specified and directed |
| 26 | S&F Mild steel, 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete fixed with screw or necessary welding to pressed steel door frame complete all as specified & directed. |
| 27 | S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples complete all as specified & directed. |
| 28 | S&F rubber lining fitted with aluminium powder coated strip, 100mm wide for door cill complete all as specified and directed. |
| 29 | S&F stainless steel peg set of six of size 400mmx30mmx3mm size fitted with machine screw and wooden and plastic cleats (minimum wt 190gms) complete all as specified and directed. |
| 30 | S&F as in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 guage with stainless steel brackets near to ends with stainless steel finials with adopter for 25 mm dia drapery rod at both ends complete all as specified and directed. |
| 31 | Supplied and fixed Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc. complete all as specified and as directed. |
| 32 | Supply & fixed Bib tap 15 mm bore long body, Brass CP, fancy type (long shank), with crutch or butterfly handle screwed down screwed for iron/PVC pipe or for brass ferrule and fixed complete all as specified. |
| 33 | Supply & fixed Stop valve /Angle valve (ISI Marked), fancy type, chromium plated with long shank and cup (concealed type). screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron /PVC pipe or for unions of 15 mm bore and complete all as specified. |
| 34 | Supply & fixed Soap dish (material SS finish, glossy) fixed to plugs with CP brass screws complete all as specified and directed. |
| 35 | Supply & fixed in repair Vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excl flushing cistern and flush pipe) but including provision concrete bedding CI floor trap etc.complete all as specified and directed. |
| 36 | Supply & fixed Push botton type PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle (incl brackets & flush pipe PVC 32 mm dia) capacity of 10 Litres complete all as specified & directed. |
| 37 | S & F corrugated waste pipe, 32 mm dia, suitable for WHBs/sinks/Urinal, including threaded PVC socket suitable for shank of waste coupling complete all as specified & directed. |
| 38 | S&F corner glass corner shelf quarter round with CP Brass Bracket, complete all as specified and directed. |
| 39 | Supply & fixed in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, floors or laid in trenches complete all as specified & directed. |
| 40 | Supply & fixed 110 mm bore PVC (SWR) bends any radius, with or without excess door complete all as specified & directed. |
| 41 | Supply & fixed in repair 110 mm bore PVC (SWR) vent cowl cap complete all as specified & directed. |
| 42 | Supply & fixed 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints , fixed to walss, laid in trenches or in floor complete all as specified & directed. |
| 43 | Supply & fixed 75 mm bore PVC (SWR) bend any radius, with or without excess door complete all as specified & directed. |
| 44 | M&L for Septic tank 50 Users designed to carry sewage and sullage water, complete including excavation and earth work in any type of soil, PCC 1:4:8 under foundation, RCC M-30 Design Mix in Roof Slab PVC rungs etc including Vent shaft , manhole openings with cover and making connection etc., of effective depth 1.5 metre and overall depth of 3 metre complete all as described and shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5. |
| 45 | Supply & laying UPVC sewage UDS ( under drainage system) pipes 160mm bore single socket, wall thickness not less than 4.5 mm type SN-4 (IS-15328) type 'A' having nominal ring stiffness should be 2 KN/m2 with one collar per length of pipe, and incl necessary returning filling and levelling to the affected portions, the UDS pipe should meet the pressure requirements as per IS 15328:2003 complete all as specified and directed |
| 46 | M&L for Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6 complete all as specified and directed . |
| 47 | M&L for Machine cut Kota stone slab flooring not less than 18-20mm thick (size of stone shall not less than 55cmx55cm), 75mm wide white marble border alround, laid over & including 15 mm thick screed base in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine complete all as specified & directed.. |
| 48 | M&L for Machine cut Kota stone slab not less than 15mm thick as in riser of steps, skirting, dado and pillar laid over & including 10 mm thick screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine complete all as specified. |
| 49 | M&L for coloured machine pressed precast rubber moulded concrete interlocking red/yellow paver block of any shape and size with 6-8 mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, m-35 Grade, laid dry over and including 50mm thick sand filling under paver, properly levelled etc, including taking out existing interlocking paver block complete all as specified and directed. |
| 50 | M&L for 25 mm thick (average thickness) PCC 1:2:4, type B-0 using 12.5mm graded stone aggregates as in floor by maintaing required gradient/undulation, finished even and fair without using extra cement complete all as specified and directed. |
| 51 | M&L for 75 mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in Sub-base to floor finishes, surface finished even and rough to receive top floor finish complete all as specified & directed. |
| 52 | M&L for rendering 5mm thick plaster in cement mortar 1:3 on concrete surfaces as in ceilings , chhajja, projection and similar isolated concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.. |
| 53 | M&L for rendering 10 mm thick cement plaster in CM 1:6 on other than fair face of brick work or concrete surface, finished even and smooth without using extra cement complete all as specified & directed. |
| 54 | Taking down cement plaster and decayed concrete of any description, upto tripple storey of building, from roof projection, chajja etc and making good the decayed portion with cement mortar 1 :3 mixed with water proofing compound as per manufacturers instruction or PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) including necessary form work and finally finished the surface with 15mm thick cement plaster in CM 1:3 complete all as specified and directed. |
| 55 | M&L for 75 mm thick cement concrete 1:3:6, type C1 (using 20mm graded agg) as in plinth protection finished even and smooth using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified & directed. |
| 56 | M&L for Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade with and including priming surface with chalk whitening complete all as specified & directed. |
| 57 | M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified & directed. |
| 58 | M&L for preparation new or previously untreated steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 59 | M&L for two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed |
| 60 | M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping, bed plates benching, slightly rounded or chamferred angles and throating including necessary form work complete all as specified & directed. |
| 61 | M&L for PCC 1: 1.5: 3, type A-0 using 12.5mm graded stone aggregates mixed with Waterproofing compound (WPC) @200ml/50Kg of cement as in levelling course on existing roof, rounded and chamfered on edges, and finished even and fair without using extra cement complete all as specified and directed. |
| 62 | M& L preperation of inaccessible roof surface by scrapping and properly cleaning the existing roof treatment in any number of layers upto original RCC roof top surafce. Apply first coat Fiber reinforced Elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index(SRI) of 100-110 , hsving minimum elongation of 350% tensile strength of 2.9 Mpa and shall have cracks bridging ability upto 2.5mm and shall resisit 10 bars of hydrostatic pressure reduce surface temperatureuoto 10 degree celsius with 33% dilution of priming coat. Laying of fiber mesh of 0.3 mm thickness weave in leno pattern having 45 gsm/Sqm and pasting it properly iwith overlap of 50mm and aloow it toodry.Apply second of undiluted coat @4.5 Ltr/Sqm. Apply third and final co for 10mm thick cement rendering in CM 1:E168at undiluted @0.45 ltr/sqm. Aplly third and final coat [email protected]/Sqm as directed by Engr in Charge.(a) M&L for 10mm thick cement rendering in CM1:3 and finishing the surface even and smooth before application of priming coat |
| 63 | S&F Wire netting made of stainless steel wire 0.71 mm dia with size of mesh 25mm fixed with tinned tacks of stainless steel wire staples complete all as specified and directed. |
| 64 | M&L for mild steel TMT bars, 8 mm dia in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed. |
| 65 | M&L for Precast reinforced cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in cover slab set in CM 1:6 complete all as specified and directed. Note : (Reinforcement shall be measured and paid separately). |
| 66 | Supply only liquid water proofing compound complete all as specified & directed. |
| 67 | M&L for Providing and injecting chemical emulsion for termite Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified & directed. |
| 68 | M&L for Providing and injecting chemical emulsion for Post Constructional along the external wall along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified & directed. |
| 69 | M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified & directed. |
| 70 | M&L for rendering 12mm thick plaster in cement mortar 1:4 on fair faces brick surfaces finished even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement, complete all as specified. |
| 71 | M&L in repairs for false ceiling of 7 to 8 mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or coloured) fixed using T grid/Cross-T/Wall angle/level clip & suspenders / hangers 4.00 mm dia GI wire (upto 120mm length) adjusting level fixed to roof slabs/ trusses of standard galvanised sections in a grid size of 600x600mm including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed. |
| 72 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified & directed. |
| 73 | M&L replacement for modular point wiring for one light/fan/bell point controlled by one switch complete with 1.5 Sqmm multistranded FRLS PVC insulated unsheathed, FRLS, multistranded copper conductor cable 1100 volts grade (red, yellow & blue) in and including medium duty non metallic rigid PVC concealed conduit 20 mm dia including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm single core FRLS PVC (green) insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete all as specified and directed.Note: The unit rate quoted include the cost of cutting chases in surfaces for conduits and fixing of sunken boxes and making good the distrubed surfaces to match the existing surfaces. |
| 74 | M&L for modular point wiring for one socket outlet 5 Amp 3/5 pin for independent board etc controlled by one switch with 1.5 Sqmm multistranded FRLS PVC insulated unsheathed, FRLS, multistranded copper conductor cable 1100 volts grade (red, yellow & blue) in and including medium duty non metallic rigid PVC concealed conduit 20 mm dia including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm single core FRLS PVC (green) insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete all as specified and directed.Note: The unit rate quoted include the cost of cutting chases in surfaces for conduits and fixing of sunken boxes and making good the distrubed surfaces to match the existing surfaces. |
| 75 | All as per description of serial item No. 73.00 here in before but for one 3/5 pin 5 amps socket outlet on same board with other switches. |
| 76 | M&L for modular point wiring but for one 15 Amp independant socket outlet using 2.5 Sqmm PVC insulated unsheathed, FRLS, multistranded copper conductor cable 1100 volts grade (red, yellow & blue) in and including medium duty non metallic rigid PVC concealed conduit 20 mm dia including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 2.5 Sqmm single core FRLS PVC (green) insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete all as specified and directed.Note: The unit rate quoted include the cost of cutting chases in surfaces for conduits and fixing of sunken boxes and making good the distrubed surfaces to match the existing surfaces. |
| 77 | S&F in repair modular switch, one module, 1 way, 10 Amps 240 volts complete all as specified and directed. |
| 78 | S&F in repair modular socket 6A, 240 volts 2 & 3 pin, 2 Module complete all as specified and directed. |
| 79 | S&F in repair modular switch, one module, 1 way, 16 Amps 240 volts complete all as specified and directed. |
| 80 | S&F in repair modular socket, 6A & 16A, 240 volts, 2 & 3 pin, 2 Module complete all as specified and directed. |
| 81 | S&F in repair modular step type fan regulator 120W, 240 volts, 2 Module, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 82 | S&F in repair modular step type fan regulator 120W, 240 volts, 2 Module, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 27 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender