Tender For special Repair To Bldg No T-22 (R/Oil) Of 389 (I) Sup Pl Asc & Of Bldg No P-85 (04 X Or Md Accn) Of 5685 Asc Bn (Mt) And Provn Of Cupboard For Mes Office At Mil Stn Haldwani Under Ge Ranikhet
Tender Value
43.26 Lakhs
Estimated cost
Bid Submission
08 Oct 2026
13 days left
EMD
86550
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nainital → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-22 (R/Oil) Of 389 (I) Sup Pl Asc & Of Bldg No P-85 (04 X Or Md Accn) Of 5685 Asc Bn (Mt) And Provn Of Cupboard For Mes Office At Mil Stn Haldwani Under Ge Ranikhet
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in but of any description and in any position not other wise specifically provided for complete all as specified and directed. |
| 2 | Demolition of brick work built in cement mortar all as specified |
| 3 | M&L for brick work with sub class `B’ bricks, straight on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 4 | M&L for brick work with sub class `B’ bricks, straight on plan to any radius in half brick thick walls, built in CM 1:4. |
| 5 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete. |
| 6 | M&L for Nominal mix RCC 1:2:4 type B-1, Slab supported on walls,beams and columns in floors,roof, landing, balconies,in type B1(20mm graded aggregate). |
| 7 | M&L for Formwork to soffits of suspended slabs such as roof slab, floor slabs landings and sgh finished surfaces of concrete flat. |
| 8 | M & L for mild steel TMT bars ,10mm dia and over , cut to length , bent to shspe required incl cranking , bending spirally for hooping for coloumns , hooking ends and bonding with (annealed) not less than 0.90 mm dia all a specified and directed |
| 9 | M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed of 15 mm thick 1:6 complete all as specified and directed by Engineer in charge. |
| 10 | M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl rounding off edges and bull noosing of all external edges over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge. |
| 11 | Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises |
| 12 | M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete |
| 13 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete. |
| 14 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete. |
| 15 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in skirting/dado or verticle surfaces with back coat of screed bed or bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified. |
| 16 | M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match with backcoat of screed bed or bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match complete all as specified.. |
| 17 | S&F Prayag hanging system and clamps support and holes with screws and back support rectangular mirror cabinet 400 X 500 (Cat No. 554) and fixed to plug with screws and cup washers complete all as apecified & directed |
| 18 | M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth. |
| 19 | Taking up or down GI Water Tubing 15mm dia (bore) including Connections and Fittings, segregating serviceable Pipes & Fittings and Stacking properly at Site(s) for re-use, complete all as specified and as directed. |
| 20 | -ditto- all as per Item No. 19 here–in–before, but for 20mm dia (Bore). |
| 21 | -ditto- all as per Item No. 19 here–in–before, but for 25mm dia (Bore). |
| 22 | Supply and Laying Steel Water Tubing 15mm dia (Bore), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed. |
| 23 | -ditto- all as per Item No. 22 here–in–before, but for 20mm dia (Bore). |
| 24 | -ditto- all as per Item No. 22 here–in–before, but for 25mm dia (Bore). |
| 25 | S&F in repair 15mm dia bib taps long body CP Brass with Capstanhead, screwed down, screwed for iron pipe of bore 15mm complete. |
| 26 | S&F brass 15mm Chromium plated Basin Mixer swan neck valve hot and cold screwed down for iron pipe complete . |
| 27 | S&F in repair Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 28 | S&F Brass chromium plated shower rose 125mm size with 225 mm Flange, swivel joints, including fixing to steel pipe or union complete all as specified and directed. |
| 29 | S&F Tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges all as specified. |
| 30 | S&F Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium plated bracket guard and SS railing complete all as specified and as directed |
| 31 | S&F Soap Dish Stainless Steel complete all as specified & directed. |
| 32 | S&F Peg Set of 6 Stainless Steel as approved by Engr-in-Charge. |
| 33 | S&F Corner Glass Shelf 300mm (with ABS Brackets) 300 x 600mm as approved by Engr-in-Charge. |
| 34 | S&F Brass CP Wall mixer for mixing hot & cold water (3 in 1) screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified. |
| 35 | S&F Towel Ring including necessary stain less steel screws, rawl plugs and washers complete all as specified and directed. |
| 36 | S&F Brass CP Sink Mixer swan neck with regular spout for mixing hot & cold water screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified |
| 37 | S&F stainless steel plate rack of stainless steel 1.00 mm thick of size size 24 x 30 x 10 inch of best quality including necessary stainless steel screws, rawl plugs and washers complete all as specified and directed. |
| 38 | Demolition and taking out cement mortar or lime concrete, brick bats from sunken floor portion complete all as specified and as directed. |
| 39 | M&L for 15mm thick cement plaster as in sunken portion of WC/Bath room using CM (1:4) on fair faces of concrete surfaces using WPC where ever required as per manufacturerer's instructions and finishing the surface even and smooth (using extra cement) etc. incl finishing even and fair complete all as specified NOTE -WPC shall be measured and paid separetely. |
| 40 | M&L for 40mm thick PCC 1:2:4 type B-0 as in Sunken Portion of WC/Bath room (using 12.5mm graded stone aggregate) complete all as specifed and directed. |
| 41 | M&L for cleaning surface of Sunken Portion of WC and applying a coat of bitumen primer @0.30 Kg/Sqm and thereafter applying a tack coat of industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and provn of APP based polymeric membrane minimum weighing 3.60Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (Wt not less than 150 gms/sqm) laid on bituminous surfaces by forced application over entire roof area, with side lap not less 100mm and end lap not less than 150mm complete all specified. |
| 42 | M&L for lime concrete with lime mortar 1:5:10 mix using 40mm graded brick coarse aggregate in sunken Portion of WC/bath room complete all as specified and as directed. |
| 43 | S&F in repair vitreous China squatting pan, Orissa pattern incl CI spun trap, size 580 x 440 mm white, with integral foot rests squat pattern closet also includes setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed. |
| 44 | S&F in repair PVC Flushing Cistern 10 litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS Brackets,CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed. |
| 45 | S&F vitreous china wash basin with pedestal, white, flat back, size 550mm x 400mm, including brackets, PVC waste pipe 32mm dia, waste coupling brass, chromium plated and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs complete all as specified and directed. |
| 46 | S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 47 | S&F in repair PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed. |
| 48 | S&F in repair for PVC (SWR) pipes 110 mm single socketed, in any length with rubber ring joints, fixed to walls including necessary clamps etc complete all as specified and as directed. |
| 49 | S & F in repair PVC (SWR) 110 mm pipes single socketed, in any length with rubber ring joints, laid in trenches including necessary clamps etc complete all as specified and as directed. |
| 50 | M&L for S&F in repair for PVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, fixed to walls including necessary clamps etc complete all as specified and as directed. |
| 51 | S & F in repair PVC (SWR) 75 mm pipes single socketed, in any length with rubber ring joints, laid in trenches including necessary clamps etc complete all as specified and as directed. |
| 52 | S & F in repair 75 bore PVC (SWR) bends any radius complete all as specified and directed. |
| 53 | S & F in repair 110 bore PVC (SWR) bends any radius complete all as specified and directed. |
| 54 | S & F in repair PVC (SWR) junction single 75 mm , (Single T) equal or unequal complete all as specified and directed. |
| 55 | S & F in repair PVC (SWR) junction single 110 mm , (Single T) equal or unequal complete all as specified and directed. |
| 56 | S & F in repair PVC (SWR) vent cowls 110 mm dia complete all as specified and directed.. |
| 57 | S&F in repair for PVC (SWR) floor trap 75 mm, plain with & including CP grating, including jointing with solvent cement complete all as specified and directed |
| 58 | Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete. |
| 59 | Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm each with shutters (without taking off shutters from the frames) complete. |
| 60 | Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 61 | Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately. |
| 62 | Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 65 x 125 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 63 | Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 65 x 100 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 64 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virginpolymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 65 | Providing and fixing 32mm thick Factory Made Wire Mesh Solid WPC Door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 20mmx40mm for stiles and 20mmx40mm for top, lock & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacturer. 20mmx40mm M.S. square tubes shall be covered with 6mm thick heat moulded \\"Rajshree\\" WPC prelaminated 'C' channel of size 30mm thickness, 140mm width out of which 125 mm shall be fiat and 15mm shall be bent in 90° angle on either side forming stiles & 6mm thick 165mm wide WPC sheet out which 150mm shall be flat and 15mm shall bent in 90° on the inner side to from top and bottom rail and 180mm wide WPC sheet out of which 150mm shall be flat and 15mm shall be bent in 90° on both side to from lock rail. 12 mm (6mm x 2) thick, 20mm wide cross WPC sheet as gap insert for top rail & bottom rail. Panel will be of Stainless Steel. wire mesh of 24 gauge to be fitted in by 'C' channel of size 32x10mm on the either side in the stiles. The inner side C channel is fixed by 20mm x 40mm M.S. tube on both sides with screws. The wire mesh in top, bottom & lock rail is sealed with 20mm x 40mm tube with Stainless Steel Wire mesh 12mm (6mm x 2) thick PVC strip of 20mm width is to be stuck & nails on both side of Stainless Wire mesh gauge interior at the top, bottom & lock rail. 10mmx20mm stainless steel pipe grill fix with M S Frame for support wire mesh as per selected design. An additional 6mm thick WPC strip of 22mm width is to be stuck on the interior side of 'C' channel using WPC solvent cement adhesive etc Complete all as specified and directed by Eng-in-charge |
| 66 | S&F Stainless steel sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extuded sections of stainless steel and fixed 300 mm long complete. |
| 67 | S&F 150 mm overall length floor stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed |
| 68 | S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed |
| 69 | S & F Stainless steel handle, cast type anodized 150mm size. |
| 70 | S & F 200 mm long stainless steel barrel tower bolts of extruded section complete all as specified and as directed. |
| 71 | S&F Butt hinges Stainless steel of 100mm long complete all as specified and directed. |
| 72 | S&F powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified. |
| 73 | Sheet glass 4.8mm thick tinted glass and glazing in squares complete. |
| 74 | S&F powder coated aluminium windows and ventilator shutters, side hung type without sash, aluminium sections weighing 0.55 Kg/m including necessary jointing cleat, glazing clips, rubber packing anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (01 Nos) hinges type B-21 100mm long (2 Nos) suitable handles (1 No) complete |
| 75 | S&F figured glass pin headed type and glazing with oil putty in square n. exc 0.5 sqm in each pane 3mm thick glass. |
| 76 | S&F Aluminium Powder coated designer grill of 5.5 mm dia and aperture of 75 mm fixed with and including aluminium powder coated flat section of size 50 x 1.5 mm and suitable aluminium anodised frame F/H section complete all as specified and directed. |
| 77 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed |
| 78 | S&F for door closer aluminium extruded section hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed Please Enable Macros to View BoQ information |
| 79 | S&F for door closer aluminium extruded section hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender