Tender For Provn Of 1X 250 Kva Transformer And Connected Cable Network At Raipur Lines Under Ge Jammu
Tender Value
32.43 Lakhs
Estimated cost
Bid Submission
07 Oct 2026
4 days left
EMD
65000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of 1X 250 Kva Transformer And Connected Cable Network At Raipur Lines Under Ge Jammu
BOQ
| Sl. No. | Item Description |
| 1 | Supply & erecting in truly vertical position steel tubular swaged poles 410 SP-55 (11.00 mtrs long) complete with 300 x300x 6 mm thick MS base plate continuously welded at bottom of pole and MS sheet 2 mm thick plug welded at top, bolts, nuts & screws including one shop coat of red oxide primer and internally bituminous painted including painting with two coats of aluminium paint and black and white strips 30 cm upto 1.5mtr height from top of coping in strips and anti climbing device complete all as directed by Engineer-in-Charge (Earth work & PCC shall be measured & paid for separately). complete all as specified and directed. |
| 2 | M&L for danger notice board/plate of 1.6mm thick mild steel sheet , vitreous enamelled white with letters, figures , and conventional skull and bone in signal red colour and fixed with MS clamps bolts approved size of HT 25cmx20 cm complete all as specified and directed. |
| 3 | Supply and Fixing of Route indicator showing detail with red colour \\" 11 KV DANGER \\"made up of mild steel plate of size 25 cm (l) x 20 cm (w) x 2 mm thickness welded to MS Flat 20 x 5 mm with overall length 45 cm complete with errection in ground with suitable PCC works along with UG cable paths to identify and exact routing of buried HT electrical cable complete all as specified and directed. |
| 4 | M&L Anti climbing device, spikes type, fabricated out of MS bars (round, square or flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the poles, spike welded to flat iron, including on primer coat, one under coat and two finishing coats of silver aluminium paint including preparation of surfaces, complete all as specified and as directed by Engr-In-Charge |
| 5 | Supply and fix lightning arrestor HT 11 KV expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp. complete all as specified. |
| 6 | M&L for earthing complete with galvanized steel plate earth electrode 60cmx60cmx6mm thick surrounded by char coal and salt buried directly in ground vertically in pit of depth not less then 2.25 mtr below ground level with top edge of the earth plate at depth of not less then 1.5 mtr below ground level surrounded from all sides by charcoal dust and common salt in alternate layers of 15 cm depth and earth plate electrode connected to galvanised earth strip of 32x6 mm dia by means of GI nuts bolts, check nuts and washers and connected to earthling test point drawn through 40mm dia GI pipe for protection of GI earth strip including 20mm dia GI pipe for watering GI funnel , PCC earth pit (1:3:6) type C-2 with CI frame and RCC cover all as shown in electrical Plate No 3 on SSR Part-I including testing all as directed by Engr-In-Charge. |
| 7 | S&F of Galvanised Iron strip of size 25x4 mm with saddles and fixing screws on porcelain insulator/spacer fixed at every 1 mtr length as lightening conductor for lightening arresters / GOD on HT poles incl necessary nut & bolts all as specified and directed by the Engr-in-Charge. |
| 8 | Supply and fix cable jointing kit for 11 KV grade cable for outdoor termination , heat shrink type, joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 95 sqmm. |
| 9 | Material & Labour of Cross arms bracing support clamps, back plate etc fabricated from structural steel section with bolts, nuts, washers,welding, bending cold or hot,drilling holes for bolts in any shape and size as directed or indicated and painted with one coat of red oxide primer and two coats of Silver paints, complete all as sepecified dirceted by Engr-in-charge. |
| 10 | Supply and fixing of switch air break gang operated triple pole mechanically operated from ground level, mounted on insulators and steel frame (12 insulator type) outdoor type suitable for vertical installation single break provided with locking arrangement consisting of MS channel, HT post top insulator with drop out fuses operating rod 25mm bore GI pipe medium grade confirming to relevant IS, current rating 200 Amp and voltage 11 KV including jumpering, lead of wire/cable as directed at site. complete all as specified and directed. |
| 11 | Supply, installation, testing and commissioning of transformer step down outdoor type copper wound , oil cooled IP-43 plinth mounted powder coated capacity 250 KVA CL-I with latest feature complete with standard fitted HT 11 KV 3 Phase LT 433 V 3 phase 4 wire, 50 C/S oil immersed naturally cooled externally cooling tube delta connection on primary HT 11 KV side and star connection on secondary LT 433 V with tapping at +/- 2.5% to +/- 5% & +/- 7.5% on HV side and to be charged by means of hand operated off load/tap changing gear including first filling of new transformer oil of dielectric strength not less than 60 KV with all fiiting and accessories such as LT box at LT side,silica gel,brather, oil level indicator, conservator tank with oil level indicator,drain out valve (oil tank), exhaust vent,air release valve, temp gauge and cast iron wheel etc complete Level-2 as per IS-1180(Part-1):2014, complete all as specified and directed. |
| 12 | Construction of Plateform for installation of transformer with and including Earth work, Brick work, PCC, RCC, Plastering, chain link fencing, gate etc all as shown in Drawing No CWE/TD-230/2021 Sheet 1/1 dated 23 Jun 2021, complete all as specified and directed. |
| 13 | M&L for Feeder Pillar Box outdoor type having thickness of 3.15mm and inner shell made out of 2mm thick MS sheet and MS angle section 50x50x6 mm mounted on PCC 1:2:4 type B-1 platform 60 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door system . “U” type gasket shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof complete with the following :-Incoming :- (a) MCCB , 500 Amps, 4P, 415V,35KA , Adj type - 01 Each, Al busbar of capacity 750 Amps - Set of four.Outgoing :- (a) MCCB , 160 Amps, 4P, 415V, 35KA , Adj type - 02 Each ( 01 Spare) , (b) MCCB, 63 Amps, 4P, 415V, 16 KA , Adj type - 08 Each ( 02 Spare) , LED indicator lamp set, RYB -01 Set.Multi Functional digital meter (A/V/PF/F) , CT Coils of suitable ratio as suitable size-01 Set. |
| 14 | Supply, laying, testing and commisioning HT underground cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire aromoured electric power cables (heavy duty) with aluminium stranded condutor served with an inner sheathing of PVC tape armoured with galvanized steel strip and overall PVC sheathed 11000 volts grade (earthed) of cross sectional area of size 95 sq mm 3 core complete as directed. |
| 15 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 400 sq mm 3.5 core complete all as specified. |
| 16 | All as per Description Srl Item No 15 but size 120 sqmm 3.5 core complete all as specified. |
| 17 | All as per Description Srl Item No 15 but size 35 sqmm 3.5 core complete all as specified. |
| 18 | Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth and getting out in soft/loose soil or hard/dense soil for taking up or laying of cable all as specified and directed. |
| 19 | Description all as per srl item No -18 above but depth exceeding 1.5 m and not exc 3.0 m complete all as specified . |
| 20 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cms. complete all as specified and directed. |
| 21 | Removing excavated material not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above starting point complete all as specified and directed. |
| 22 | Supply and laying un-reinforced precast concrete cable cover, class HVP, type 1 with peak size 300 mm x 180 mm x 40 mm complete all as specified and directed. |
| 23 | Bricks common burnt clay sub class 'B' old size for cable protection complete all as specified and directed. |
| 24 | Supply and laying dry river sand laid in trenches as cable cushioning and covering all as directed.Sand cushioning to under ground electric cable 8cm before laying and 15cm after laying the cable intrenches all complete all as specified and directed. |
| 25 | M&L PCC 1:2:4 type B1 using 20mm stone aggregate for coping of pole and stay assembly complete all as specified and directed. |
| 26 | M&L PCC 1:3:6 type C2 using 40mm stone aggregate for stay assembly complete all as specified and directed. |
| 27 | M&L PCC 1:4:8 type D2 using 40mm stone aggregate for pole foundation complete all as directed |
| 28 | M&L Cable jointing kit for 11000 Volts grade (E) cable outdoor termination heat shrinkable straight through joint complete with jointing material suitable for 3 core XLPE armoured aluminium joint conductor cable of size 95 Sqmm and jointing materails for making joints and testing complete all as specified and directed. |
| 29 | Taking down old UNSV cable (UG LT) of following size complete all as specified and directed. |
| 30 | (a) Old UNSV LT cable of size 35 Sqmm complete all as specified and directed. |
| 31 | (a) Old UNSV LT cable of size 120 Sqmm complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender