Tender For Paint, Sanitation, Motor Installation & Aluminium Partition Work In Ward Development Centre In Ward No 19.
Tender Value
5.74 Lakhs
Estimated cost
Bid Submission
26 Sep 2026
4 days left
EMD
11500
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dumka → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Paint, Sanitation, Motor Installation & Aluminium Partition Work In Ward Development Centre In Ward No 19.
BOQ
| Sl. No. | Item Description |
| 1 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 2 | Extra for cleaning the old surface by scrapping the entire old white wash or colour wash including cost of scaffolding all complete as per direction of E/I. |
| 3 | Distempering with 1st Quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound) content less than 50 gram/litre, of approved brand and manufaturer including applying additional coats wherever required to achieve even shade and colour 13.81.1 Old work (one or more coats) |
| 4 | Providing one coat of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I. |
| 5 | Providing one coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 6 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): 3 track Anodised aluminium (anodised transparent 1868, Minimum anodic coating of grade AC 15) |
| 7 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight notless than 10 kg/sqm) |
| 8 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides |
| 9 | Wiring for light point/ fan point/exhaust fan point/ call bell point with 1.5 sq. mm FR PVC Insulated Copper Conductor single core cable in face/recessed PVC conduit, with modular type switch, modular plate, suitable size PVC/ G.I. box etc. as required.a) Group C |
| 10 | Twin Control point wiring in PVC conduit, withmodular type switch:-Wiring for twin control point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way with modular switch, modular plate suitable GI box etc as required |
| 11 | Wiring for circuit/ sub main wiring along with earth wire with the following sizes PVC insulated copper conductor single core cable in surface/recessed PVC conduit as required. e). 2x2.5 sq mm+1x2.5 sq. mm. earth wire |
| 12 | e). 2x4 sq mm+1x4 sq. mm. earth wire |
| 13 | S/F power plug point with modular type accessories:-S/F suitable GI box with modular plac and cover in front on surface of in recess,including providing and fixing 3 pin 5/6 amps modular scoket outlet and 5/6 amps modular switch,connection,painting etc. as required |
| 14 | S/F power plug point with modular type accessories:-S/F suitable GI box with modular plac and cover in front on surface of in recess,including providing and fixing6 pin15/16 amps modular scoket outlet and 15/16 amps modular switch,connection,painting etc. as required |
| 15 | Supplying and fixing 2 pin 5 amps ceiling rose on the existing junction box/ wooden block including connection as reqd. |
| 16 | Supplying and fixing batten/angle holder including connection etc as reqd. |
| 17 | S/F rewireable double pole/TP&N switch disconnector :-Providing and fixing following DP/TP&N sheet metal switch disconnector fuse unit in the existing metal board with rewireable type fuses,including drilling holes in metal board,making connection.etc as required 63 amps,TP&N |
| 18 | Providing and fixing following capacity 2pole/4 pole ON/OFF-load changeover switches with side handla operation.in sheet enclosure in existing metal board including drilling holes in metal board,making connection,earthing the body etc as required. 63 amps, 4 pole |
| 19 | S/F following way three pole neutral, sheet MCB distribution board, 415 volts on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc as reqd. (But without MCB/RCCB/ Isolator)a) 4 way (4+12) , double door horizontal type |
| 20 | b) 6 way (4+18) , double door horizontal type |
| 21 | S/F following 6 amps to 32 amps rating 240 volts,10 KA, ‘C’ curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connection, testing and commissioning etc. as reqd. b) 6/32 amp,Single pole |
| 22 | S/F of the following size of exhaust fan including cutting the wall and fixing exhaust fan etc as required (a) 9”(230mm)metal exaust fan |
| 23 | S/F stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate |
| 24 | S/F 48”(1200mm) AC ceiling fan with all accessories etc. as reqd. |
| 25 | S/F 9/10 watt LED Bulb |
| 26 | S/F LED Flood light (30W) |
| 27 | Earthing with copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc |
| 28 | Extra for using salt and charcoal for pipe earth electrode as reqd. |
| 29 | Supplying laying 8 SWG copper wire at 0.50 meter below ground label for conductor earth electrode, including soldering etc. as reqd. |
| 30 | Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware ware urinal of Hindustan \\"Parry\\" or any other approved ISS make with 5 ltrs. Capacity C.I. Automatic fushing cistern of reliance for any other ISS approved make with all fittings with C.I. or RS brackets standard size G.I. flush pipe with fitting clamps 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 gms. 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. Flat back or standing corner (450X350mm) |
| 31 | supping fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I or R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I. 630X450 |
| 32 | Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specification and direction of E/I. (a) 20mm dia. |
| 33 | (b) 25mm dia. |
| 34 | Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. 15mm dia |
| 35 | Providing and fixing cp brass pilar cock weight not less then 350gm. C.I body brass spindle pillar cock of approved quality as per specification and direction of E/I |
| 36 | Providing and fixing cp brass long body bib cock of approved quality confirming to IS 1831 15MM |
| 37 | Supplying, materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I. |
| 38 | Angular stop cock L.T. |
| 39 | 32mm dia. PVC waste pipe 750mm long with cushion ( |
| 40 | 15mm C.P. Nipple with coupling |
| 41 | Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. Brass revolving fitting 3mm ply wood board and C.P. Hinges to fix with mirror 600 X 450mm |
| 42 | Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc. |
| 43 | P/F 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of E/I. |
| 44 | P/F Chlorinated ployvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipe & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the wall etc. 15MM |
| 45 | P/F on wall face unplasticised - Rigid P.V.C Rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110mm dia |
| 46 | P/F on wall face unplaqsticised- PVC moulded fitting/accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A, including jointing with seal ring confirming to IS:5382 leaving 10mm gap for thermal expansion, (i)Single Tee with door110x110x110mm |
| 47 | Single Tee without door110x110x110mm |
| 48 | Bend 87.5 degree110mm bend |
| 49 | Coupler110 mm |
| 50 | Providing and Placing on terrace (at all floor levels) (PVC) Polyethylene water storage tank ISI 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 51 | Supplying, installing in to the 200 mm /165mm Nominal dia bore well & commissioning of Suitable dia Submersible Motor pump set pump capable to discharge 0.75 LPS against a total head up to 85 mtrs of Kirlosker / Jyoti / KSB make as per IS 1520/1980 coupled with 220 V, single phase ,50 Hz AC and wet type winded submersible motor , including cost of32mm dia GM full way wheel valve 32mm dia NR valve heavy type MS Clamps -2 Nos etc as per requirement , all complete job as per direction of E/I with rope. 1.5 HP |
| 52 | P/F Chlorinated ployvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipe & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the wall etc. 32MM |
| 53 | Supplying, installing & commissioning of panel board suitable for the motor pump set as mentioned in the item No. - 5, having voltmeter, ammeter, phase indicating lamps, starters, main switch, fuses, inter connection in the panel board including cost of wires etc all complete job as per specification and direction E/I. |
| 54 | Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX/HEVELS make including all taxes royalty etc all complete job as per direction of E/ . |
| 55 | Supplying, & commissioning of 5 KVA Servo Stabilizer of Sen & Pandit or Pagaria or approved eqivalent make (Range 90 V - 300 V) single phase with cable, change over switch for Submersible Pump etc. all complete as per specification and direction of E/I. |
| 56 | providing 32 mm dia GI elbow confirming IS specifiction including cost of all material labours jointing material all complete job |
| 57 | supply and fixing G.I Reducing tee plain 32 mm dia. |
| 58 | GST 18% |
| 59 | LABOUR CESS 1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysSep 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender