Tender For Special Repair To P30a And P30b At 313 Coy Asc Sup Type F And Provn Of 10 X Security Lights With Poles And Adequate E And M Fitting At Various Loc In 261 Cedu 06 X Acs For Sigcen In 51 Sub Area Sig Pl Loc Under Ge Narangi
Tender Value
49.27 Lakhs
Estimated cost
Bid Submission
06 Oct 2026
9 days left
EMD
98540
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To P30a And P30b At 313 Coy Asc Sup Type F And Provn Of 10 X Security Lights With Poles And Adequate E And M Fitting At Various Loc In 261 Cedu 06 X Acs For Sigcen In 51 Sub Area Sig Pl Loc Under Ge Narangi
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced ) of any description & in any position not specifically provided for complete etc all as specified and as directed |
| 2 | Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed. |
| 3 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed |
| 4 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and as directed |
| 5 | Dismantling timber scantlings 40 sq. cm and over in section, in any position as in Framed work etc complete all as specified and as directed |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed |
| 7 | Demolition of brick work /stone masonry/PCC block masonry built in cement mortar of any description all as specified and directed. |
| 8 | Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each etc complete all as specified and as directed |
| 9 | Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4.0 Sqm each etc complete all as specified and as directed |
| 10 | Taking down cement plaster of any description hacking for key or raking out joint on old brick work/ stone /concrete surface etc complete all as specified and as directed |
| 11 | Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet) etc complete all as specified and as directed |
| 12 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons , laid bedded and pointed in any mortar etc complete all as specified and as directed |
| 13 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise etc complete all as specified and as directed |
| 14 | Taking up or down 15mm steel tubing and connections incl cleaning for refixing and removal to store etc complete all as specified and as directed. |
| 15 | Taking up or down 20 mm steel tubing and connections incl cleaning for refixing and removal to store etc complete all as specified and as directed. |
| 16 | Dismantling water tanks and removing to store (exc 500 and not exc 1000 ltr capacity) etc complete all as specified and as directed |
| 17 | Dismantling water tanks and removing to store (exc 1000 and not exc 2000 ltr capacity) etc complete all as specified and as directed |
| 18 | Demolition and breaking up drain pipes up to 100 mm dia bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar etc complete all as specified and as directed |
| 19 | Material and labour for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality-A etc complete all as specified and as directed |
| 20 | Material and labour for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe 410-W (Gde E- 250), Quality 'A' quality etc complete all as specified and as directed |
| 21 | Supply and fix pre-painted hot dip aluminium zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (total coated thickness), any patteren corresponding to IS 15965: 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour havingb yield strength of 550MPa as in roof covering/wall cladding, fixed with self tapping screws as complete all as specified and as directed. |
| 22 | Supply and fix pre-painted hot dip aluminium zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (total coated thickness), any patteren corresponding to IS 15965: 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour havingb yield strength of 550MPa as in roof covering/wall cladding, fixed with self tapping screws as specified and as directedNote: To be executed for provison of ridges and hips, valley etc complete all as specifed and as directed |
| 23 | Material and labour for 75 mm thick cement concrete type D- 2, 1:4:8 (40mm graded stone aggregate) as in sub base of flooing etc complete all as specified and as directed |
| 24 | Material and labour for cement concrete type B-0 1:2:4 (12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed |
| 25 | Material and labour for 75 mm thick PCC 1:3:6, type C-1, using 20 mm graded stone aggregates as in plinth protection etc, finished even and smooth without using extra cement complete all as specified and as directed. |
| 26 | Material and labour for forming constractin joint (Dummy joint) 65 mm deep X 10 mm wide filled with sealing compound grade 'A\\" etc, complete all as specified and directed. |
| 27 | Material and labour for Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes etc complete all as specified and as directed |
| 28 | Material and labour for Screed bed or bedding layer of mortar 20 mm thick in CM 1:3 for laying floor finishes etc complete all as specified and as directed |
| 29 | Material and labour for Rendering 10 mm thick in CM 1:4 for backing coat of tiles / dado etc complete all as specified and as directed |
| 30 | Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing incl cutting edges etc complete all as specified and as directed |
| 31 | All as per item No 30 above but as in skirting /dado / Vertical Surface etc complete all as specified and as directed. |
| 32 | Material and labour for Glazed ceramic coloured tiles (Glossy Finished) of size 600X600X7mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and as directed |
| 33 | Material and labour for Virified Ceramic tiles light shade double charged 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed |
| 34 | Material and labour for 20mm thick granite Granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like, in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab including grinding the edges half round etc complete all as specified and as directed |
| 35 | Material and labour Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 etc complete all as specified and as directed |
| 36 | Material and labour Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in Cm 1:4 etc complete all as specified and as directed |
| 37 | Material and labour for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed |
| 38 | All as per item No 37 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed |
| 39 | Cleaning the existing surface of concrete and reinforcements as obtained by wire brush including scrapping & cleaning with emery paper and washing down with water as required and Material and labour for applying “Solvent free epoxy concrete bonding agent” as per manufacturer’s instructions on old concrete surfaces for bonding with new concrete complete all as specified and as directed. |
| 40 | Material and labourfor two coats of “Epoxy zinc rich primer” as protective coat to expose surface of old and new reinforcement over 10 mm dia as per manufacturer's instructions complete all as specified and as directed. |
| 41 | Material and labour for RCC (Nominal mix) type A-1, 1:1.5:3 (20mm graded stone aggregate) as in Beams, cantilevers, bressummers, chajja, lintels over 1.5m span etc complete all as specified and directed. |
| 42 | Material and labour for RCC (Nominal mix) type A-0, 1:1.5:3 (20mm graded stone aggregate) as in Beams, cantilevers, bressummers, chajja, lintels over 1.5m span etc complete all as specified and directed. |
| 43 | Material and labour for providing reinforced cement concrete (1:1½: 3) type A0 (using 12.5mm graded stone aggregate) mixed with integral water proofing liquid admixture as per manufactures instructions as in columns, pillars, piers, posts and struts complete all as specified and as directed. |
| 44 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished concrete surfaces complete all as specified and as directed. |
| 45 | Use and waste of formwork to sides and soffits of beams, lintels, floors etc. for rough finished concrete surfaces complete all as specified and as directed. |
| 46 | Use and waste of formwork to parapet, RCC wardrobe and similar items for rough finished concrete surfaces complete all as specified and as directed. |
| 47 | Use and waste of formwork to sides and soffits of chajja, troughs etc for rough finished concrete surfaces complete all as specified and as directed |
| 48 | Use and waste flate formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all specified and as directed. |
| 49 | Material and labour for RCC type B1 nominal mix 1:2:4 (using 20 mm graded stone agrregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed. |
| 50 | Material and labour for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete / Stone masonry surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed |
| 51 | Material and labour for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) over 5 mm thick in CM 1:4 mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately |
| 52 | Material and labour for 1mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed |
| 53 | Material and labour for Preparing new plastered suface of walls and applying two coats of acrylic distemper , white or tinted over a coat of primer etc complete all as specified and as directed |
| 54 | Material and labour for Preparing Old plastered suface of walls and applying two coats of acylic distemper , white or tinted over a coat of primer etc complete all as specified and as directed |
| 55 | Material and labour for preparation old plastered surface of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance (Apex Ultima), dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. etc complete all as specified and as directed |
| 56 | All as per item no 55 above but new plastered surface of wall |
| 57 | Material and labour for preparing newely plastered surface of ceiling and applying two coats of acrylic distemper white or tinted over a coat of primer etc complete all as specified and as directed |
| 58 | Material and labour for preparing Old surface of ceiling and applying two coats of acrylic distemper white or tinted over a coat of primer etc complete all as specified and as directed |
| 59 | Supply and fix in repairs 7 to 8 mm hollow profile thickness thick PVC Coloured Sheet (any Shape, coloured, pattern as approved ) suitably placed in false ceiling /wallsincl making sunken side corner, design as directed etc incl grid work made of G.I./M.S. as per Mfd Instruction etc complete all as specified and as directed (Make - Rajashree/ Magama /Syntax or any other equivalent make as approved by GE) |
| 60 | Supply only water proofing compound (Liquid) complete all as specified and as directed. |
| 61 | Supply and fix Factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with double rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed |
| 62 | Supply and fix 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed |
| 63 | Supply and fix 18/19mm tthick Block boards, grade 1 quality, exterior grade, commercial type, Water proof, termite proof, fixed with screws to timber frame-work as in cub board shutter, shelves and Drawers etc complete all as specified and as directed |
| 64 | Supply and fix 0.90 mm thick decorative laminate coloured type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions etc complete all as specified and as directed |
| 65 | Supply and fix Stainless steel channel for drawers of sizes 600mm long and 46mm wide complete all as specified and as directed |
| 66 | Supply and fix Stainless steel auto closing concealed hinges 9.5 cranks for half overlay doors with opening angle 95* (14-32mm) with integrated overlay adjustment + 2.50mm & depth adjustment 4mm complete all as specified and as directed |
| 67 | Supply and fix 150mm size Extruded brass handles, fabricated type polishedl handle fit to modular section etc complete all as specified and as directed |
| 68 | Supply and fix 2nd class hard wood 25 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats etc complete all as specified and as directed |
| 69 | Providing and fixing factory made uPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm) exceeding 1 sqm but not exceeding 2 sqm. Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 70 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 71 | Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 72 | Providing and fixing factory manufactured commercial heavy-duty hollow steel security door of approved make, single leaf, size as specified, fabricated from minimum 1.6 mm thick CRCA steel sheet for door shutter with internal reinforcement, fully insulated/honeycomb core, welded construction, complete with minimum 1.6 mm thick pressed steel door frame of suitable section, fixed to masonry/RCC wall with MS holdfasts/anchor fasteners as required. The shutter shall be fitted with 3 Nos. heavy-duty stainless steel ball bearing butt hinges (minimum 125 mm), heavy-duty mortice lock with lever handles on both sides, tower bolts, door stopper, hydraulic door closer (where specified), rubber/neoprene gasket, all necessary screws, bolts, washers and accessories. The door and frame shall be treated with anti-rust zinc phosphate coating, one coat of epoxy primer and finished with powder coating/baked enamel finish of approved shade. The item includes all cutting, welding, grouting with non-shrink cement mortar, making good disturbed surfaces, alignment, testing, commissioning and all labour, materials, T&P, scaffolding and incidentals complete in complete all as specified and as directed |
| 73 | Providing and fixing heavy-duty stainless steel utensil storage rack for institutional kitchen/mess, fabricated from SS 304 grade stainless steel, comprising six-tier shelves with tubular frame, complete with cross bracing, adjustable nylon bushes, stainless steel fasteners and all accessories. The rack shall be fabricated from minimum 38 mm × 38 mm × 1.5 mm thick SS square tube for vertical members and 25 mm × 25 mm × 1.5 mm thick SS square tube for horizontal supports. Shelves shall be made of minimum 1.2 mm thick SS 304 sheet with folded edges and suitable stiffeners to carry heavy utensils. The item includes fabrication, welding, grinding, polishing (matte finish), transportation, placing in position, levelling and all labour, materials, tools and incidentals complete in all respects as directed by the Engineer-in-Charge.(Note :- Overall Siz 2400 mm (L) × 600 mm (D) × 1800 mm (H), Number of Shelves 6, Load Capacity - Minimum 100 kg per shelf) |
| 74 | Providing and fixing heavy-duty stainless steel utensil storage rack for institutional kitchen/mess using for fresh vegitables and fruits, fabricated from SS 304 grade stainless steel, comprising six-tier shelves of SS mesh bucket type with three compartment in each self with tubular frame, complete with cross bracing, adjustable nylon bushes, stainless steel fasteners and all accessories. The rack shall be fabricated from minimum 38 mm × 38 mm × 1.5 mm thick SS square tube for vertical members and 25 mm × 25 mm × 1.5 mm thick SS square tube for horizontal supports. Shelves shall be made of wire mesh jali of 1 mm or 2 mm dia SS 304 sheet with folded edges and suitable stiffeners to carry heavy utensils. The item includes fabrication, welding, grinding, polishing (matte finish), transportation, placing in position, levelling and all labour, materials, tools and incidentals complete in all respects as directed by the Engineer-in-Charge.(Note :- Overall Siz 2400 mm (L) × 600 mm (D) × 1800 mm (H), Number of Shelves 6 bucket type with 3 compartment in each self, Load Capacity - Minimum 50 kg per shelf) |
| 75 | Supply and fix 4mm thick sheet Figured glass, pin head type and glazing with oil putty in squares in not exc 0.5 sq.m in each pane etcc complete all as specified and as directed |
| 76 | Supply and fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staple etc complete all as secified and as directed |
| 77 | Supply and fix Brass barrel tower bolt 200 mm long of extruded section etc complete all as specified and as directed |
| 78 | Supply and fix 100 mm thick butt hinges, medium weight, stainless steel and fixed etc complete all as specified and as directed |
| 79 | Supply and fix 125 mm thick butt hinges, medium weight, stainless steel and fixed etc complete all as specified and as directed |
| 80 | Supply and fix 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed |
| 81 | Supply and fix 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed |
| 82 | Supply and fix aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed |
| 83 | Supply and fix in repairs vitreous china wash basin white, ovel type size 550 x 400mm excluding taps, waste, chain & plug and porcelain stopper but including brackets and including, 32 mm bore waste CP coupling and 32mm bore LDPE pipe 600 mm long and 15 mm bore 450 mm long PVC connection etc complete all as specified and directed. |
| 84 | Supply and fix in repairs 15 mm dia bore CP Bib taps, fancy type cera cat no F1005152 long body and fixed etc complete all as specified and as directed. |
| 85 | Supply and fix in repairs 15 mm dia bore CP piller taps, fancy type long body cera cat pat no F1005101 and fixed etc complete all as specified and as directed. |
| 86 | Supply and fix in repairs 15 mm dia bore CP fancy type long body Stop valves/ Angle cock cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed etc complete all as specified and as directed |
| 87 | Providing and fixing heavy-duty stainless steel sink for institutional/mess kitchen, multi campartment for washing vegitable, fruits etc, manufactured from 1.2 mm thick AISI 304 grade stainless steel with satin finish, overall size 1800 mm × 600 mm × 300 mm deep (or approved equivalent), comprising double bowls with integral drain board as specified, complete with stainless steel legs/frame of 40 mm × 40 mm × 1.6 mm square tubular sections, adjustable nylon feet, 40 mm stainless steel waste coupling, PVC waste pipe, inlet/outlet connections, all necessary brackets, fasteners, welding, polishing, cutting, fitting, testing, commissioning, and making good complete in all respects. |
| 88 | Supply and fix in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws etc complete all as specified and as directed |
| 89 | Supply and fix in repairs 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers etc complete all as specified and as directed. |
| 90 | Supply and fix in repairs Towel ring of PTMT fixed with and including chromium plated brass screw and wooden / plastic (Minimium weight 90 gms) etc complete all as specified and directed |
| 91 | Supply and fix GI Tubes, 15 mm dia bore of pies 'medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed |
| 92 | Supply and fix GI Tubes, 20 mm dia bore of pies 'medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed |
| 93 | Supply and fix rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 1000 ltrs incl 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic etc complete all as specified and directed |
| 94 | Supply and fix rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 2000 ltrs incl 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic etc complete all as specified and directed |
| 95 | Supply and fix in repairs 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve complete all as specified and as directed |
| 96 | Supply and fix in repairs 75 mm dia bore PVC (SWR) multi floor trap with grating including jointing with solvent cement etc complete all as specified and as directed |
| 97 | Supply and fix 110 mm PVC, SWR pipes, single socketed in any length with rubber ring joint laid in trenches or in floor etc complete all as specified and directed |
| 98 | Supply and fix 110 mm PVC, SWR pipes, single socketed in any length with rubber ring joint fixed to walls etc etc complete all as specified and directed |
| 99 | Supply and fix 75 mm PVC, SWR pipes, single socketed in any length with rubber ring joint laid in trenches or in floors etc complete all as specified and directed |
| 100 | Supply and fix 75 mm PVC, SWR pipes, single socketed in any length with rubber ring joint fixed to walls etc complete all as specified and directed |
| 101 | Supply and fix PVC bends (any radius) of 110mm dia with access door etc complete all as specified and as directed |
| 102 | Supply and fix PVC vent cowls of 110mm dia etc complete all as specified and as directed |
| 103 | Supply and fix PVC bends (any radius) of 75mm dia with access door etc complete all as specified and as directed |
| 104 | Supply and fix 75 mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door etc complete all as specified and as directed |
| 105 | Supply and fix 110 mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door etc complete all as specified and as directed |
| 106 | Supply and fix 110mm dia bore PVC (SWR) branch pieces, double (double Y) equal or unequal etc complete all as specified and as directed |
| 107 | Supply and fix 75 mm dia bore PVC (SWR) branch pieces, single (single Y) equal or unequal etc complete all as specified and as directed |
| 108 | Supply and fix PVC vent cowls of 110mm dia etc complete all as specified and as directed |
| 109 | Complete removal exising treatment (External/Internal wall) by means of wire brushing, sand paper, manually or mechanically up to visible of plastered surface incl rubbing and washing etc complete all as specified and as directed |
| 110 | Material and labour for preparation of old painted wooden surfaces of any description exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 111 | Material and labour for preparation of New wooden surfaces of any description exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed. |
| 112 | Material and labour for Preparation of old steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint etc complete all as specified and as directed |
| 113 | Material and labour for Preparation of new or previously un-treated steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed |
| 114 | Supply and fix in repairs stainless steel decorative curtain rod of 25 mm bore incl fancy finale caps cap (02 nos in each curtain rod) etc complete all as specified and as directed |
| 115 | Supply and fix in repair Brass Chromium Plated designer Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed |
| 116 | Material and labour Cutting chases, pinning in, making good to facingsin brick walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed pipe line etc. and making good, cutting exceeding 20cm girth etc complete all a specified and as directed |
| 117 | Material and labour for Hard core with broken stone or boulder of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick water and rammed to a true surfac etc all as specified and as directed |
| 118 | Material and labour Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and as directed |
| 119 | Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed. |
| 120 | Taking down ceiling/exhaust/wall fan including connection wires carefully and deposit to MES store in safe custody complete all as specified and as directed. |
| 121 | Material and labour for Point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in and including PVC Conceled Conduit with all accessories including fabricated MS/PVC terminal boxes fixed flush box and cover plate ( for modular Switch socket ) with wall surface for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as specified and as directed. |
| 122 | All as per item serial No 121 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches complete all as specified and as directed. |
| 123 | All as per item serial No 121 here-in-before but One socket outlet 3 pin 6 Amp on independent board complete all as specified and as directed. |
| 124 | All as per item serial No 121 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and as directed. |
| 125 | Supply and fix switch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and as directed. |
| 126 | Supply and fix modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed. |
| 127 | Supply and fix modular switch 1 way 16 amp, 1 module complete all as specified and as directed. |
| 128 | Supply and fix modular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed. |
| 129 | Supply and fix stepped type modular electronic fan regulator, two module size, flush type complete all as directed. |
| 130 | Supply and fix ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as directed |
| 131 | Supply and fix modular lamp holder ,PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. |
| 132 | Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 V complete all as specified and as directed. |
| 133 | Supply and fixing in repair LED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 134 | Supply and fix LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed/surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed. |
| 135 | Supply and fix in repair LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 136 | Supply and fix in repair/replacement MCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. |
| 137 | Supply and fix in repair/replacement MCB DB of sheet metal enclosure ip-43 double door SPN 8 way with bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate all as directed. |
| 138 | Supply and fix in repair/replacement MCCB four pole 100A, Icu 16KA, thermal magnetic, 415v AC complete all as specified and as directed. |
| 139 | Supply and fix in repair/replacement MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. |
| 140 | Supply and fix in repair/replacement MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. |
| 141 | Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 142 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep, 1400 rpm with blades, and frame and louvers complete all as specified and as directed. |
| 143 | Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including taking down excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 |
| 144 | Supply and fix in repair/replacement LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and directed. |
| 145 | Material and labour for building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed. |
| 146 | Material and labour for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dia non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 147 | Material and labour for wiring with 2 runs of 6 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith single run of 6 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old wiring and type of conduit complete all as specified and directed. Note: 2 run of 6 Sqmm cable and 1 run of 6 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 148 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 4 core complete all as specified and directed. |
| 149 | Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed. |
| 150 | Supply and spreading clean dry river sand in cable trenches as in cable cushioning complete all as specified and as directed. (Note: Punned thickness shall be measured and paid) |
| 151 | Material and labour for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified |
| 152 | Returning filling in including spreading, levelling, watering and well ramming in layers n.exc. 25cm complete all as specified and as directed. |
| 153 | Removing of excavated soil not exc 50cm & depositing where as directed at a level n.exc 1.5m above starting point complete all as specified and as directed. |
| 154 | Material and labour for cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in foundation complete all as specified and directed. |
| 155 | Material and labour for PCC 1: 3 : 6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in mass concrete including necessary form work for coping to the new/existing Steel Poles complete all as specified and directed. |
| 156 | Material and labour for XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10 sqmm 4 core laid in trenches /floor or fixed on wall/pole in including brass compression cable glands, terminal lugs etc, complete all as specified and as directed. |
| 157 | Material and labour for erection of steel tubular steel tubular swaged pole type 410 SP - 31 (9.00 metres long) including cast iron base plate, finial taper plug and and painted with two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 158 | Supply and fixing high-quality LED street Light with a minimum system lumen of 12600 Lm (+/-5%) and system wattage not exceeding 90W (+/- 5%) with a nominal system efficacy of ≥140 lumen/watt. The LED used shall have CCT of 5700K, SDCM ≤ 5 and CRI≥70. The housing should be made of LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast aluminium, to withstand extreme environments. The name of the brand should be embossed/engraved and should not be mentioned using sticker/screen printing. The product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be a minimum IP66 and impact resistance shall be IK10. The Luminaire should have a minimum 10KV/10KA SPD duly bolted in the Luminaire. The luminaire should be of Class B Serviceability. The Driver should be asphalt potted and should be a BIS approved driver. The driver shall have operating voltage of 120V to 270V, PF≥0.95 @ full load, THD≤10% @ full load. The driver should be capable to withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The luminaire driver, it’s SPD shall be of the same make/manufacturer as that of LED luminaires complete all as specifed and directed |
| 159 | Material and labour for connection of junction box to street light luminaire using wiring with two runs (P-N) of single core 1.5 Sqmm (nominal area) FR-LSH PVC insulated and unsheathed multi-stranded copper conductor cable 1100 volts grade and one run of FR-LSH PVC insulated and unsheathed multi-stranded copper conductor of size 1.5sqmm single core as earth continuity wire drawn through PVC conduit(Heavy grade) and tiding the same by aluminium strip with the pole complete all as specified and directed. (Two single core 1.5 Sqmm cable and one single core 1.5 Sqmm earth conductor cable and one run of PVC conduit shall be measured as one run). |
| 160 | Supply and fix CPRI (Tested) street light panel of suitable dimension outdoor type, powder coated,dust and vermin proof IP-55,prewired , operates on three phase made with 1.6mm thick CRCA sheet with locking arrangement duly painted. having auto/manual selector switch, including MS flat iron clamp (Clamp shall be 40X 5mm ), nuts bolts & washers for fixing arrangement with pole and connecting incoming/outgoing cable with suitable size of lugs and comprising the following.(i) MCB , Four Pole of capacity 32 Amps ,C-curve of breaking capacity 10kA-2 Nos ( one for I/C and another for O/G)(ii) Astronomical timer(Astro mini ) 110-240VAC, 1 Phase . Cat Part No. T2DDT7 of L&T or equivalent in Havells/C &S (iii) 3 Pole contactor of Current rating MNX 50 Amps , with inbuilt surge suppressor and RoHS compliant. (iv) LED type red indicator lamp (v) Auto/ Manual selector switch(vi)2A, SP, 10kA MCB- 01 Nos (For timer protection) |
| 161 | Material and labour for Manual boring under roads/hard standing by reqd T&P without disturbing the top surface of the road for throughing the cable in GI Pipe of n exc 80 mm dia all as specified and directed. |
| 162 | Material and labour for GI pipe light grade 40mm bore dia with all fittings to be laid in trenches or in floors,including taking down rusted one complete all as speciffied and as directed. |
| 163 | Supply and fix street light junction box of size 205 x 255 x 112mm made of high quality polycarbonate with IP-66 protection (Dust and vermin proof according to IEC-60529) Totally insulated made of halogen and silica free recyclable material having high quality gasket made out of polyurethane with MCB, DP, 10KA, 6 Amps to be fixed on Din rail , with locking arrangement with cable gland suitable upto 25 to 35 sqmm cable and necessary fixing arrangements such as clamps, nuts, bolts etc all as specified & directed by Engr-in-Charge. Make : Hensel Cat No -KF-1616B. |
| 164 | Material and labour earthing complete with galvanised steel earth plate electrode of size 600mm x 600mm x 6 mm thick burried directly in ground (Earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below ground level connected to galvanised earth lead by means of bolts nuts, check nuts and washers of galvanised iron or steel using GI strips 32 X 6mm as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earth test point all as specified or indicated including GI pipe 40mm bore(dia) for earth lead protection ' light grade', GI pipe 20mm Bore(dia) ' Medium grade' for watering including necessary excavation any type of soil, RCC chamber cover plate, wire mess, funnel, etc complete and testing on complete all as specified and directed. |
| 165 | Supply and install high wall split units indoor & outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating Inverter (INV) tech AC with complete copper coil, and ISEER 4.52 and 5 star rating of capacity of 2TR including copper pipe of required size , bracket fabricated using MS angle iron not less than size 50x50x6 cm including necessary nuts, plug tops, bolts washer etc as required at site for mounting outdoor unit of AC on wall complete all as specified and as directed. Make: Bluestar/LG/ HITACHI |
| 166 | Supply and fixVoltage stablizer for automatic operation. Single phase naturally air cooled indoor type & designed for input variation between 100 V to 280 V with output voltage stablized at 200 V to 240 V with accuracy of 2% and of current carrying capacity 5 KVA complete all as specified and as directed. |
| 167 | Supply and fix Sheet metal enclosure for with two pin and earth plug and socket complete with SPN MCB upto 32 Amps, 240 Volts capacity and tested on complete all as specified and as directed. |
| 168 | Material and labour for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit complete all as specified and as directed. |
| 169 | Material and labour for Sub main wiring with 2 runs of 6.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. Note: 2 run of 6 Sqmm cable and 1 run of 6 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 170 | Supply and fix factory made, sheet steel distribution boards, TPN, 4 Way, IP-43 double door,with provision for FP MCB as incomer and SP MCBs as outgoing complete and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. |
| 171 | Supply and fix MCB Tripple pole & neutral 40 to 100 Amps in accordance with IS/IEC 60898-1, 415 V, 50 Hz,10 kA,C-series rupturing capacity providing in DB complete all as specified and as directed. |
| 172 | Supply and fix MCB DB of sheet metal enclosure IP-43 double door SPN 8 way with 200 A rated bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. |
| 173 | Supply and fix MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. |
| 174 | Supply and fix MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. |
| 175 | Material and labour for plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m deep below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth lead wire 4 mm dia or 8 SWG bolted (with GI nuts, bolts & check nuts) and earth plate electrode at one end and connected to main switch board/ DBs etc. at the other, earth strip encased(protected) in and including 15 mm bore GI pipe medium grade with all fittings from top of electrode to main switch board/ DBs etc fixed with and including 25 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-2 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work complete all as specified and shown in electrical plate No 3 of SSR Pt-I. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysOct 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender