Tender For Addition/Alteration And Special Repair To Certain Md Accn At Lekhapani Mil Stn Under Ge Dinjan No 2
Tender Value
2.27 Crore
Estimated cost
Bid Submission
19 Oct 2026
33 days left
EMD
3.02 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration And Special Repair To Certain Md Accn At Lekhapani Mil Stn Under Ge Dinjan No 2
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of unreinforced cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all complete. |
| 3 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. Brushing neat cement slurry with 3.0kg of cement per sq. metre |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work & precast concrete articles complete all as specified & directed. |
| 5 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water & removal of debris off the premises etc. complete all as specified & directed. |
| 6 | Demolition of reinforced cement concrete of any description n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.(Shelfs and chimneys) |
| 7 | Dismantling of plain or corrugated steel sheeting any guage, thickness including Nanital or similar pattern roof coverings complete all as specified and as directed. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete |
| 9 | Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 10 | Dismantling of boarding any description fixed in any position complete all as specified and directed. |
| 11 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5sqm each and making good to disturbed surfaces complete all as specified and as directed by the Engineer-in-Charge. |
| 12 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5sqm but not exceeding 4.0sqm each and making good to disturbed surfaces complete all as specified and directed by the Engineer-in-Charge. |
| 13 | Supply and fix, factory made pressed steel frames for doors with two rebates, of size 125mmx60mm, made out of 1.25mm thick sheet, including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed. |
| 14 | Supply and fix, factory made pressed steel frames for doors with one or more rebates, of size 105mmx60mm, made out of 1.25mm thick sheet, including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed. |
| 15 | Supply and Fixing Providing “RAJSHRI BRAND” factory made white colour 3- TRACK UPVC SLIDING WINDOW are made of UPVC extruded profiles with wall thickness of 2.3 mm ( + 0.2 mm ), Window profile with hollow section with multi chamber, Frame ( 109 mm x 52 mm ), Sliding sash ( 80 mm x 47 mm ), Sliding interlock ( One vertical length in each shutters ) ( 43.5 mm x 50.5 mm ), Glazing bead ( 22 mm x 4.5 mm ) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket,1.5 mm (+ 0.2 mm) thick, galvanized steel Frame ( 29 mm x 18 mm )2nos.,Sliding sash ( 28 mm x 17 mm ), Sliding mesh sash (29mmx13mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners. complete as per manufacture's specification and direction of Engineer-in-charge |
| 16 | Supply and fixing factory made uPVC white colour Two track two panels sliding glazed window upto 1.50m height made of (small series) frame 50 x 42.5 mm & sash 32 x 54 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.20 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. |
| 17 | S & F 5mm thick sheet glass, ordinary quality and glazingwith oil putty in square exc 0.5 sq. m in each pane .pane ® |
| 18 | Supply and Fixing Providing “RAJSHRI BRAND” factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi champhered frame sash and mullion (where ever requered) extuted profile duly reinforfed wit 1.2 +- 0.20mm thick galvanised mild steell section made from roll forming process of required length (shape & size according to uPVC profile ), uPVC estruded glazing beads of appropriate dimension , EPDM gaskit stainless steel (SS304 grade ) friction hinges zinc allow (white powder coated )casement handel G .I fasterner 100x8mm size for fixing frame to finished wall , plastic packers plastic caps and nessary stainless steel screws etc .profile and frame sash shel be mitered cut and fusion welded at all corners, mullion (if requered ) shal be also fusion weled icluding drilling of holes for fixing hardware and drainage of water etc after fixing of frame the gap between frame and adjacent finishesd wall shal be filled with weather proof silicon sealant over backer rod of requered size and approed quality all comlete as per approved drawing and direction of Engr-in-Charge . (Single / double rebete ) glass panes and siicone sealent.shall not be paid seperatly, with SS Friction hinges (300x19x1.9mm)made of small series frame 50x50mm mullion66x50mm & sash 47x68mm both having wall thikness of 1.9+-0.2mmand single glass panesglazing beadof appropriate dimnsion. |
| 19 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 20 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ S & F Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 21 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush Cup board door shutter of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 22 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shelves of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant fixed over stainless steel L shaped brackets which should withhold as average weight of 20-30 Kg and fixed with ecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 23 | S/F factory made Flush shutters 35mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete. |
| 24 | S/F factory made Second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. |
| 25 | S/F factory made Second class hardwood half glazed and half panneled door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, and half pannelwith 9mm BWP commercial ply etc complete. |
| 26 | S&F 75mm size aluminium anodiesd Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws. |
| 27 | S&F door seal aluminium rod with nylon brush of approved colour fixed to shutter with and incl 20 mm steel wooden screws complete all as specified and directed. |
| 28 | S&F Floor door stopper doubled leged of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor. |
| 29 | S&F MS Chroumium plated curtain rod 25 mm dia with and incl MS Chromium plated decorative round funnals on either end and provide a visually balanced appearance incl MS Chromium plated brackets fixed to wall with 30mm wooden steel screws and PVC rawal plug anchors and installation as fixed in repairs complete all as specified. |
| 30 | S&F 150 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed. |
| 31 | S&F 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed. |
| 32 | S&F 250mm length of bolt, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & as directed. |
| 33 | S&F 100mm butt hinges, type B-21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised & fixed to PVC door complete all as specified & as directed. |
| 34 | S&F mild steel 300mm size, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed. |
| 35 | S&F 125mm size stainless handles, cast type, anodized and fixed complete all as specified & as directed. |
| 36 | S & F 75mm Stainless steel chromium plated fancy type handle for cupboard/cabinets fixed with scres and nut complete all as specified and as directed |
| 37 | S&F 150mm size aluminium handles, cast type, anodized and fixed complete all as specified & as directed. |
| 38 | S&F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with fixed with steel wire staples complete all as specified & directed. |
| 39 | S&F 4mm thick frosted sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5sq. m in each pane complete all as specified and as directed. |
| 40 | S & F stainless steel soft close hydraullic clip concealed cabinet hinges fixed with stainless steel screw complete all as specified |
| 41 | S & F Stainless steel Magnetic door catcher Magnet of size 50x15mm fixed with stainless steel screw on shelf/sides wall and shutter complete all as specified and as directed |
| 42 | Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1, cutting exceeding half brick but not exceeding one brick complete. |
| 43 | M & L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete |
| 44 | Material & labour for false ceiling with GI frame work for EXPOSED GRID SYSTEM of grid size 600 mm x 600 mm, GI powder coating at bottom and comprising of GI perimeter wall angle with two equal flanges of 25 mm fixed to surrounding wall / partition using nylon sleeves and screws at 450 mm centre to centre. Main Tee 0.55 mm thick having 35 mm wide flange and 25 mm high web suspended from the soffit @ 1200 mm centre to centre with level clip with wire of 4 mm dia, Cross Tee - 1200, 0.55 mm thick having 35 mm wide flange and 25 mm high web inserted fixed into the slots of Main 'T' @ 600 mm centre to centre to form a grid of 1200 mm x 600 mm, Cross Tee - 600, 0.55 mm thick having 35 mm wide flange and 25 mm high web shall be placed perpendicular to the Cross Tee - 1200 to finally form a grid of 600 mm x 600 mm . complete all as per manufacturer instructions and all as shown on Drawing No. CESZ/2019/TD-42, Sheet No. 1/1. |
| 45 | S&F 4mm thick high pressure, oceanic pre-primed, self embossed, non asbestos fibre cement decorative board, water, termite and fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 2 to 3 mm dia GI wire hangers fixed with steel dash through fasteners from purlins with butterfly clips, hold down clips, with provision of ligh fixtures, air conditioning, diffuser and ducts, sprinkler, smoke detector etc. complete all as per manufacturer instructions and all as shown on Drawing No. CESZ/2019/TD-42, Sheet No. 1/1. |
| 46 | S/F Rolled mild steel sections conforming to Fe 410 (GdeE250 ) quality A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates complete. |
| 47 | M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 48 | M&LPre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 49 | M&L for 15mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 50 | S & F stainless steel sinks with drainage board made out of 1.00 mm thick sheet for kitchen with plugs, washers, waste pipes, including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm with bowl size 410mm x 330mm x 160mm, with and including PVC waste pipe and CP waste coupling 32 mm dia and making good to disturbed surfaces, fixed in repairs, complete all as specified. |
| 51 | M/LForm work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished flat surfaces of concrete complete. |
| 52 | M&L RCC 1:2:4 Nominal mix B-1(20mm graded aggregate) as in as in slab supported on walls beams & columns in floors, roofs, landings, balconies, canopies, deck slabs & in shelves & the like etc complete all as specified and directed |
| 53 | M&L TMT bars 8 to 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. |
| 54 | S&F framed work such as griils, grating, angle iron door frames etc., with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, laders, framed balusters, walk ways, railings frame work of RHS/SHS for water tanks and similar work conforming to Fe-290. Gde E-165 complete all as specified & as directed. (Balcony Railings) |
| 55 | M/L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 complete. |
| 56 | M&L for brick work with sub class old size 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete as specified and directed. |
| 57 | M&L for rendering 10.mm thick plaster in cm 1:6 on fair faces of brick work or concrete surfaces including finishing top even and fair complete all as specified & directed. |
| 58 | Rendering in two layers (10+5) 15 mm thick on brick or concrete surfaces in cement mortar (1:4) mixed with 3% of WPC in top layer and finished even and fair without using extra cement , including necessary scafolding and form works, upto first floor complete all as specified complete all as specified.(Note : WPC shall be measured and paid seperately) |
| 59 | M & L rendering 5 mm thick on ceiling in CM(1:3) finished even and smooth without using extra cement complete all as specified |
| 60 | Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed by Engineer - in -Charge.Note: The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required upto 7.00 Mtr height building. |
| 61 | M & L 75 mm thick, plain cement concrete 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection/pavings/shafts including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement, complete all as specified. Note: The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm. |
| 62 | M/L Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in Hardstanding/Footpath/shaft pavings , 75mm thick, finished even and fair complete. |
| 63 | M/LChequered cement concrete tiles with grey pigment cement and pigments in equal proportions and no pigments 200mm x200mm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15mm screed bed for laying floor finishes complete. |
| 64 | M/LCement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in surface channels and drains complete. |
| 65 | M/LExtra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete. |
| 66 | M/LPrecast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in in manhole perforated cover slab including necessary moulds and setting in cement mortar 1:4 complete. (reinforcement to be measured separately) |
| 67 | Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out soft/loose soil complete. |
| 68 | Returning, filling in excavated approved soil,(soft/loose soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete. |
| 69 | Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete. |
| 70 | S&F of 150 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors/ trenchs and making good all as specified. |
| 71 | Demolition of lime concrete/ lean concrete/ brick bats from sunken portion exc. 15 cm thickness (above ground level), including removal of rubbish outside MoD land, complete all as specified. |
| 72 | Roughening surfaces of sunken floor by sweeping clean and washing down with water to remove dust etc incl brushing neat cement slurry with 3.0 Kg of cement per sq metre and renderning 5mm thick in cement mortar 1:3 mised with water proofing compound as per manufacturers instruction and Applying evenly a coat of blown type bitumen at the rate of 1.5 Kg per sqm and blinding with clean dry sand @ 0.05cum per sqm and laying of black polythene film 150 micron thick laid over a coat of bitumen primer @ 0.30 to 0.5 Kg per Sqm in sunken surface complete all as specified and as directed Note : WPC Shall be measured and paid seperately |
| 73 | PCC (1:2:4), type B-1, using 20 mm graded mechanically crushed stone aggregates, as in padding concrete to sunken floor, covering to junction of floor and vertical walls including chamfering on edges, complete all as specified and directed by Engineer - in -Charge. |
| 74 | Supply only integral water proofing compound, complete all as specified. |
| 75 | Steel water tubes, 40 mm bore, light grade, galvanized, as in spout for sunken floor, fixed in wall, inside end fixed with wire netting and external beveled edge at 45 degree, complete all as specified and directed by Engineer - in -Charge. |
| 76 | Lean concrete (1:5:10), type E-2, using 40 mm brick coarse aggregate, as in sunken portion, complete all as specified and directed by Engineer-in-Charge. |
| 77 | M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.50mm graded stone aggregates), in sub base of floors, finished even & fair to receive bedding layer of cement mortar complete all as specified and directed. |
| 78 | M&L for glazed coloured ceramic tiles in vertical surface 450x300 x 7mm , set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles laid over & including 10 mm thick rendering as in backing wall plaster in cement mortar (1:4) complete all as specified & directed. |
| 79 | M&L for coloured Anti skid joint free ceramic tiles of 7mm to 8mm thick (Approx Size 300x300) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified & directed. |
| 80 | M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick (Approx Size 400x400) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified & directed. |
| 81 | M&L for coloured Matt finished joint finished ceramic tiles of 7mm to 8mm thick (Appx size 600mmx600mm) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified & directed. |
| 82 | M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in cement mortar 1:4 for vertical surfaces such as skirting etc complete all as specified & directed. |
| 83 | M & L Green Marble work 18 to 20mm thick (table rubbed and polished) in corner shelf design/Rectangle design fixed independently at Bath and Kitchen incl rounding the edges, like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed. |
| 84 | M&L for plain cement concrete (1:3:6), type C-1, (using 20mm graded crushed stone aggregates) as in bed block, blocks for holdfasts, filling in pressed steel door frames , benching slightly rounded or chamfered angles & throating etc including necessary use & waste of form work complete all as specified and directed. |
| 85 | M/LMachine cut Pre polished Kota stone slab flooring 18-20mm thick over 15mm thick cement screed of cement mortar 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. Note : (Kota stone to be fixed in staircase thread shall be of single piece) |
| 86 | M/LMachine cut Pre polished Kota stone slab flooring 18-20mm thick over 10mm thick cement screed of cement mortar 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing as in risers of steps, skirting, dado etc complete. Note : (Kota stone to be fixed in staircase thread shall be of single piece) |
| 87 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete |
| 88 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified |
| 89 | S&F PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed. |
| 90 | S&F PVC (SWR) pipes 75mm dia single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed. |
| 91 | S&F PVC (SWR) bends 110mm dia any radius provided with access door all as specified and directed. |
| 92 | S&F PVC (SWR) bends 110mm dia any radius with out access door all as specified and directed. |
| 93 | S&F PVC (SWR) bends 75mm dia any radius provided with access doorall as specified and directed. |
| 94 | S&F PVC (SWR) junction single, (single T) 110mm dia any radius provided with access door all as specified and directed. |
| 95 | S&F PVC (SWR) junction single (single T) 75mm dia any radius provided with access doorall as specified and directed. |
| 96 | S&F 150x150mm Salt-glazed stoneware gully traps, square or round mouthed, type `P' complete all as specified and directed |
| 97 | Taking up or down steel water tubing and connections, including cleaning for refixing or removal from site, for bore of pipes 15mm dia complete all as specified and directed. |
| 98 | S&F UPVC 15mm dia bore of pipes of pressure rating 10 kgf/Sqcm with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed. |
| 99 | Taking up or down steel water tubing and connections, including cleaning for re-fixing or removal from site, for bore of pipes 20mm dia complete all as specified and directed. |
| 100 | S&F UPVC 20mm dia bore of pipes of pressure rating 10 kgf/Sqcm with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed. |
| 101 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete. |
| 102 | S&F in repairs vitreous china squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor complete all as specified and directed. |
| 103 | S & F in repair vitreous china wash down water closet pan (pedestal pattern), white including connection to drain or outgoing pipe and to flushing pipe antisyphonage pipe etc with plastic water closet seat, black closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified & directed. |
| 104 | S&F in repairs Wash basins, vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and directed. |
| 105 | S & F brass bottle trap 7\\" complete all as specified and directed |
| 106 | S&F brass health faucet with 1 Mtr tube and hook complete all as soecified and directed |
| 107 | S & F in repairs 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed. |
| 108 | M&L 75mm dia PVC (SWR) floor trap/nahani trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 109 | S/F Stainless steel Grating doom 125 mm dia with waste hole of complete. |
| 110 | PVC connections of PTMT, non corrosive, with nuts & washers on both ends, 450 mm longs suitable for 15 mm bore, ISI marked, fixed in repairs, complete all as specified. |
| 111 | S&F 40 mm Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqm as in waste water pipes complete fixed in wall, ceiling or in floors all as specified & directed. |
| 112 | S&F in repairs 15mm bore dia stop valves / angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed. |
| 113 | S&F 15mm bore dia angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed. |
| 114 | S&F 15mm bore cast copper alloy, fancy type, chromium plated,concealed type long shank and cup screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed. |
| 115 | S/F in repairs Pillar taps, Long neck cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete. |
| 116 | S/F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete. |
| 117 | S/F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore suitable for fixing of washing machine complete. |
| 118 | S & F 5mm PVC sheet Mirror Cabinet of size 400 x 500mm as per cat Part No 554 of Prayag or equivalent complete all as specified and as directed |
| 119 | S & F 15mm bore sink cock Regular spout with long neck and flag complete all as specified and as directed |
| 120 | S & F wall mixer with L Bend with provision for over head shower complete all as specified and as directed |
| 121 | S & F 100mm chromium plated overhead shower ABS with Brass Arm 225mm and flange complete all as specified and as directed |
| 122 | S&F soap dish of stainless steel fixed to wall with chromium plated brass screws fixed in repair complete all as specified & as directed |
| 123 | S&F Brass chromium Plated towel rail 600mm long with brackets 20mm dia fixed to wall with chromium plated brass screws fixed in repair complete all as specified & as directed . |
| 124 | S&F Wall Mount Modern Kitchen Utensils Dish Rack Stainless Steel (31 x 10 x 30 Inches) |
| 125 | S&F in repair stainless steel peg set of 6 peg, 45 centimeter long, complete all as specified. |
| 126 | Dismantling water tanks exc 250ltr but not exceeding 500ltr capacity complete all as specified and as directed. |
| 127 | S&F rotational moulded polyethylene water storage tanks of 500 ltr capacity,(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I & as directed. |
| 128 | S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe & fixed (Minimum weight 210 gms) complete all as specified & as directed. |
| 129 | S/F in repairs 20mm Gun metal,globe or gate valve, with iron wheel head screwed both ends for iron pipe and fixed complete |
| 130 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) Exc 250 Ltr an Nexc 500 Ltr. |
| 131 | M & L Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. |
| 132 | Surface Preparation 1. Concrete surface must cleaned with wire brush/grinder to remove loose mortar and must be smooth, uniform, clean and dust free to receive the treatment. Concrete profile should be in the range of CSP 3-4. Preliminary Treatment 2. Any crack, construction joints shall be treated with Polymer modified repair mortar/ SC General purpose grout by proper grooving arrangement [10 x 5 mm] as per manufactures recommendation. 3. Block work joints, Block wall -slab interface to be packed with Polymer modified repair mortar/ SC General purpose grout. Treatment to continue up to full Hight of the planter wall. 4. Angle fillet - Making coving (50X50mm) using M20 Grade Concrete integral waterproofing Vitalia NEO admixed with additive 200 ml per bag of cement as per manufacturer’s specification 5. Testing by ponding water for 24-72 hours to identify surface defects min. 25 mm-100 mm, a. First Ponding Test to be on Structural Slab, b.. Second Ponding Test after waterproofing Treatment, c. Third Ponding Test after Screed laying Bore packing (Treatment steps given separately) 6. If any leak/dampness observed post water ponding Test, it needs to be pressure grouted with SmartCare General Purpose Grout. 7. Skim tape to be provided wherever dissimilar material ( Steel, PVC ) encountered, to overlap the coating. |
| 133 | Damp Roof Ultra Application: - Supplying and applying High build elastomeric waterproofing coating Asian Paints SmartCare DP Ultra is a fiber reinforced elastomeric liquid applied waterproofing membrane which id formulated with PU hybrid polymers and reinforcing acrylic polymers, Resists positive hydrostatic pressure of up to 10 bars, Effectively bridges cracks up to 2.5 mm, Reduction Provides surface temperature reduction up to 12 °C, Excellent resistance to water, UV rays and ageing, The consumption to be maintained is 10sqft/L |
| 134 | M/L Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete. |
| 135 | Complete removal of existing treatment on wall/ roof projections incl facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust loose paint etc by skilled labour complete all as specified and as directed |
| 136 | M & L for waterproof cement based putty @ 1 Kg (undiluted) per sq mtr(internal/External) of average thickness 1mm over the plastered / old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanicsm) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface free from dust etc by skilled labour as per following steps : -Step 1 : Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 Kg putty per minute.Step 2 : Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a max pressure 3300 PSIStep 3 : Allow 6-8 hrs time to dry the putty surfaceNote : (a) The work pertaining to periodical services and water proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by GE.(b) Cost of Scafolding upto 10 mtr height of building is included in this item.(c) The contractor shall upload along with the documents under cover I , Memorandum of understanding (MoU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.(d) Masking of waindow/doors during spray painting using polythine film will be included (e) Cleaning and clearing site of paint, mats etc included.(f) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against painting work after date of completion for the 05 years. |
| 137 | M & L for applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface scomplete all as specified and directed.Note : (a) Sanding of surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper mashking to carried before primer and paint application.(b) The work pertaining to periodical services and water proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by GE.(c) The contractor shall upload along with the documents under cover- I , Memorandum of understanding (MoU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.(d) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against painting work after date of completion for the 05 years. |
| 138 | M & L for one coat of acrylic water based exterior grade primer @ 0.9 ltr (undiluted/10 sqmtrs diluted with water 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.Note : (a) The work pertaining to periodical services and water proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by GE.(b) Cost of Scafolding upto 10 mtr height of building is included in this item.(c) The contractor shall upload along with the documents under cover- I , Memorandum of understanding (MoU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.(d) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against painting work after date of completion for the 05 years. |
| 139 | M & L for two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additive and color stay Techonology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/litre as per the LEEDS specifieecations, Anti Algal properties in two coats @ 1.79 ltr (Undiluted)/10 Sqm with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow spreed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface in both coats of paint complete all as specified and directed.Note : (a) The work pertaining to periodical services and water proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by GE.(b) Cost of Scafolding upto 10 mtr height of building is included in this item.(c) The contractor shall upload along with the documents under cover- I , Memorandum of understanding (MoU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.(d) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against painting work after date of completion for the 05 years. |
| 140 | M&L preparing new wood & wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed. |
| 141 | M&L for preparation of new or previously steel surfaces of any description, over 10 cm width or girth, not otherwise described and evenly applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 142 | M&L for preparation of New plastered surfaces of wall and applying three coat of white wash complete all as specified & directed. |
| 143 | M&L for preparation of old plastered surfaces of wall and applying three coat of white wash complete all as specified & directed. |
| 144 | M&L for preparation of New plastered surfaces of ceilings and applying three coat of white wash complete all as specified & directed. |
| 145 | M&L for preparation of old plastered surfaces of ceilings and applying one coat of white wash complete all as specified & directed. |
| 146 | M&L for preparation of New painted surfaces of steel of any description, not otherwise described, Nexc 10cm width or girth and applying two coat of synthetic enamel paint over a coat of Red oxide complete all as specified & directed. |
| 147 | M&L for preparation of old painted surfaces of steel of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed. |
| 148 | M&L Providing and injecting chemical emulsion for Post constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltrs per linear metre incl drilling and plugging holes and mnatch the existing floors using cement mortor 1:2 complete all as specified and directed. |
| 149 | M&L Providing and injecting chemical emulsion for Post constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole 300mm apart incl drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existisng floors complete all as specified and directed. |
| 150 | S&F RAJSHRI SOLID WPC JALISPECI FICATION OF 18 MM SOLID WPC BOARD - PLAINProviding \\"RAJSH RI\\" Brand Factory Made 1 8mrri thick 1 00% Solid WPC ( Wood polymer Composite ) JALI of required size comprising of virgin PVC resin of K Value 58-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by \\"RAJSH RI\\" an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC Jali to be fixed with stainless Steel butt hinges ( if required ) of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For Interiors / Kitchen shutters / Balcony & Internal Doors and Partitions. |
| 151 | Supply & Fixing mild Steel work in hollow square/rectangular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 4923 -1997 (Reaffirmed 2009) grade Yst.-310 complete all as specified and directed. |
| 152 | Taking down carefully (copper/aluminum) unsv point wiring complete of any type (batten/surface conduit or concealed) for light point, fan point, bell point ,socket point or power point including fixture and fitting such as switches , ceiling roses, pendants , regulators , sockets , light fitting etc. removing material to store for keeping in safe custody or for taking credit( credit for above items should be made as per conditions seperately) and making good the disturbed surfaces of wall/floor or ceiling to match with existing surface and finishing the surfaces with distemper/white washing/colour washing as per existing complete all as specified and directed. |
| 153 | Taking down ceiling fan any type and size and keep in safe custody for refixing after complition of work all as specified and as directed. |
| 154 | Taking down Exhaust fan any type and size and keep in safe custody for refixing after complition of work all as specified and as directed. |
| 155 | Taking down elctric meter any type and keep in safe custody for refixing after complition of work all as specified and as directed. |
| 156 | Taking down water heater/ geyser any type and any capacity and keep in safe custody for refixing after complition of work all as specified and as directed. |
| 157 | Taking down old submain wiring of any type/ core incl earth wire incl batten/ PVC conduit/ casing capping and making good the disturbed surface to match with the existing all as specifid and as directed. |
| 158 | Taking down old MCB DB of any type and size and making good the disturbed surface to match with existing all as specified and as directed. |
| 159 | Taking down old MCB (SP/SPN) of any type and size all as specified and as directed. Please Enable Macros to View BoQ information |
| 160 | Taking down old MCB (SP/SPN) of any type and size all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 33 daysOct 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 40 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender