Tender For Construction Of Alumni Canteen Behind Cit Building, Jamia Millia Islamia.
Tender Value
15.03 Lakhs
Estimated cost
Bid Submission
06 Oct 2026
20 days left
EMD
30069
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Alumni Canteen Behind Cit Building, Jamia Millia Islamia.
BOQ
| Sl. No. | Item Description |
| 1 | EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m._All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 4 | CEMENT CONCRETE (CAST IN SITU) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :_1:5:10 (1 cement: 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | REINFORCED CEMENT CONCRETE |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 8 | Foundations, footings, bases of columns, etc. for mass concrete |
| 9 | Suspended floors, roofs, landings, balconies and access platform |
| 10 | Shelves (Cast in situ) |
| 11 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level._Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level._Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 15 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. |
| 16 | All works upto plinth level_Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 17 | All works above plinth level upto floor V level_Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 18 | MASONRY WORK |
| 19 | Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement: 6 coarse sand) :_With Modular bricks |
| 20 | CLADDING WORK |
| 21 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels._Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble_Area of slab over 0.50 sqm |
| 22 | WOOD AND P. V. C. WORK |
| 23 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:_35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 24 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378)_250x16 mm |
| 25 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378)_200x10 mm |
| 26 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378)_125 mm |
| 27 | STEEL WORK |
| 28 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters._80x1.20 mm M.S. laths with 1.20 mm thick top cover |
| 29 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. |
| 30 | FLOORING |
| 31 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :_25 mm thick |
| 32 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 33 | ROOFING |
| 34 | 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay: 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat:_With common burnt clay F.P.S.(non modular) brick tile of class designation 10 |
| 35 | Providing gola 75x75 mm in cement concrete 1:2:4(1 cement :2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design :_In 75x75 mm deep chase |
| 36 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 37 | Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement: 4 fine sand)._Stone ware spout |
| 38 | FINISHING |
| 39 | 12 mm cement plaster of mix:_1:4(1 cement: 4 fine sand) |
| 40 | 15 mm cement plaster on rough side of single or half brick wall of mix:_1:4(1 cement: 4 coarse sand) |
| 41 | 6 mm cement plaster 1:3 (1 cement: 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. |
| 42 | Finishing walls with water proofing cement paint of required shade:_New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 43 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :_Two or more coats on new work |
| 44 | SANITARY INSTALLATIONS |
| 45 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 46 | Kitchen sink without drain board |
| 47 | 610x510 mm bowl depth 200 mm |
| 48 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 49 | Flexible pipe |
| 50 | 40 mm dia |
| 51 | Providing and fixing soil, waste and vent pipes : |
| 52 | 100 mm dia |
| 53 | Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 |
| 54 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 55 | 100 mm inlet and 100 mm outlet |
| 56 | Sand Cast Iron S&S as per IS: 1729 |
| 57 | WATER SUPPLY |
| 58 | Providing and fixing PPR Unions |
| 59 | PPR Union 25mm |
| 60 | PPR Union 32mm |
| 61 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 62 | 25 mm nominal dia Pipes |
| 63 | 32 mm nominal dia Pipes |
| 64 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 65 | 25 mm nominal bore |
| 66 | 32 mm nominal bore. |
| 67 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 68 | Providing and fixing PTMT bib cock of approved quality and colour._15 mm nominal bore, 86 mm long, weighing not less than 88 gms |
| 69 | Providing and fixing PTMT pillar cock of approved quality and colour._15 mm nominal bore, 107 mm long, weighing not less than 110 gms |
| 70 | Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms |
| 71 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour._15 mm nominal bore with 45 cm length |
| 72 | Modified Estimated Cost after using correction factor on DSR 2023 on account of GST @ 0.973 * 1391631 = 1354057 |
| 73 | Electrical Work |
| 74 | WIRING |
| 75 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc. as required._Group C |
| 76 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 77 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 78 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 79 | 4 X 16 sq. mm + 2 X 6 sq. mm earth wire |
| 80 | Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required. |
| 81 | Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 82 | Upto 450 mm sweep |
| 83 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 84 | MCCB, MCB & DB'S |
| 85 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required. |
| 86 | 125 A,36KA,FPMCCB |
| 87 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) |
| 88 | 8 way (4 + 24), Double door |
| 89 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 90 | Single pole |
| 91 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 92 | 100 A |
| 93 | EARTHING |
| 94 | Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt) as required. |
| 95 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 96 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 97 | MV CABLE JOINTING & END TERMINATION |
| 98 | Market Rate (M.R.) |
| 99 | Supplying of Trans air exhaust fan 300 mm High speed, 1300 RPM to 1380 RPM.70 Watts.Double Ball Bearing with 100% Copper winding.Metal body with 4 blades, powder-coated finish.Single phase 220 - 240 Volts AC 50Hz.Bird screen included, rust-proof, suitable for wall mounting. Crompton Greaves /Orient/Havells, make or as approved by Engineer In-charge etc. |
| 100 | Supply of Ceiling fan 1200 mm (But with-out regulator) capacitor type having service value >=5 complete with 30 cm down road, canopies, hanging shackle High speed, 320 r.p.m , 68 Watts ,Double Ball Bearing with 100% Copper winding.Metal body with 3 Aluminum blades, down rod, shackle, screws & nuts, powder-coated finish.Single phase 220 - 240 Volts AC. 50 Hz ,Orient New Breeze PSPO /Havells / Crompton greaves Make etc as reqd. or Eqiuvalent as approved By Engineer Incharge |
| 101 | Supply & Fixing 100 amp FP Enclosure ,Havells Make Suitble for Fixing of MCCB 100 Amp FP incomming & outgoing connection of cable Fixing Thimbling Including providing Anchor Dash Fasteners Suitble for Enclosure etc as requried . |
| 102 | Supplying of Exhaust fan 375 mm High speed, 900 RPM to 90 Watts./100 watt Double Ball Bearing with 100% Copper winding.Metal body with 4 blades, powder-coated finish.Single phase 220 - 240 Volts AC 50Hz included, rust-proof, suitable for wall mounting. Crompton Greaves /Orient/Havells, make or as approved by Engineer In-charge etc. |
| 103 | Supply Installation, Testing and Commissioning of 20-watt LED batten (typically 4 feet in length) with a PVC/Polycarbonate (PC) housing is a highly energy-efficient and lightweight lighting solution. It provides widespread, glare-free illumination, making it a standard choice for homes, office Philips / Havells /cromton , Make or Eqiuvalent as approved By Engineer Incharge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysOct 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender