Tender For Upgradation Of Toilet Block Near Smbk-05 At Lebong Under Age (I) Darjeeling
Tender Value
9.70 Lakhs
Estimated cost
Bid Submission
06 Oct 2026
3 days left
EMD
19400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Darjeeling → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Upgradation Of Toilet Block Near Smbk-05 At Lebong Under Age (I) Darjeeling
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of plain or corrugated steel sheeting of any gauge & thickness from roof, gutter etc incl Nainital or similar pattern roof coverings, complete all as specified and as directed by Engineer-in-charge. |
| 2 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge. |
| 3 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., complete all as per specified and as directed by Engineer-in-charge. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge. |
| 5 | M&L for 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes, complete all as specified and as directed by Engineer-in-charge. |
| 6 | S&F coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles, complete all as per specified and as directed by Engineer-in-charge. |
| 7 | M&L for 10 mm thick rendering in CM (1:3) on stone masonary surface or surface other than fair face of brickwork, complete all as per specified and as directed by Engineer-in-charge. |
| 8 | S&F Glazed ceramic coloured tiles of 450x300x7/8mm thick tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as per specified and as directed by Engineer-in-charge. |
| 9 | S&F chequered cement concrete coloured tiles 30cm x 30cm x 20 mm thick set, jointed and pointed in neat cement slurry with grey cement and no pigment cement, complete all as per specified and as directed by Engineer-in-charge. |
| 10 | Taking down chowkat or frame not exceeding 1.5 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge. |
| 11 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening complete all as per specified and as directed by Engineer-in-charge. |
| 12 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed by Engineer-in-charge. |
| 13 | S&F 75 mm long medium weight, cold rolled mild steel butt hinges, complete all as specified and as directed by Engineer-in-charge. |
| 14 | M&L for 125 mm long aluminium pressed handles, cast type anodised, complete all as per specified and as directed by Engineer-in-charge. |
| 15 | S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge. |
| 16 | Demolition of brick work built in any cement mortar complete all as specified and as directed by Engineer-in-charge. |
| 17 | M&L for brick work with fly ash bricks (old size), straight or curved on plan to any radius in half brick thick walls, built in CM (1:4), complete all as specified and as directed by Engineer-in-charge. |
| 18 | M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in in CM (1:6), complete all as specified and as directed by Engineer-in-charge. |
| 19 | Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge. |
| 20 | M&L 10 mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces and finished the surface even & smooth without using extra cement complete all as per specified and as directed by Engineer-in-charge. |
| 21 | M&L rendering 15 mm thick on fair faces of brickwork in cement mortar 1:4 on other than fair faces of brick work using WPC @ 3% by weight of cement (WPC to be measured and paid separately) finishing even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge. |
| 22 | Supply only integral water proofing compound confirming to IS complete all as per specified and as directed by Engineer-in-charge. |
| 23 | M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge. |
| 24 | M&L for preparation of old decorated plastered or unplastered surfaces of walls including brooming down or steel wire brushing, scrapping down smoke scoot, mould, moss and efflorescent salt, trading oil and greasy spots and applying two coat of white wash, complete all as per specified and as directed by Engineer-in-charge. |
| 25 | M&L for preparing new plastered surfaces and applying two coats of cement based paint on walls over a coat of alkali resistant primer, complete all as per specified and as directed by Engineer-in-charge. |
| 26 | M&L for preparation of old decorated plastered or unplastered surfaces of wall, cornices etc by brooming down or steel wire brushing, scrapping down, smoke soot, moulds, moos efflorescent and trading oil and greasy spots and applying two coats of cement base paint (white or tinned), complete as specified and as directed by Engineer-in-charge. |
| 27 | M&L for preparation of old steel surfaces of any description not otherwise described over 10cm girth or width and applying one coat of synthetic enamel paint, complete all as per specified and as directed by Engineer-in-charge. |
| 28 | Taking out old existing galvanised iron water mains 15 mm bore (including all fittings) with spigot and socket ends and fittings for re-use in the work and removing unserviceable pipes and fittings from site complete all as per specified and as directed by Engineer-in-charge. |
| 29 | Taking out old existing galvanised iron water mains 20 mm bore (including all fittings) with spigot and socket ends and fittings for re-use in the work and removing unserviceable pipes and fittings from site complete all as per specified and as directed by Engineer-in-charge. |
| 30 | S&F GI tube 15 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge. |
| 31 | S&F GI tube 20 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor, complete all as specified and as directed by Engineer-in-charge. |
| 32 | S&F in repair gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe of 20 mm bore including dismantling unserviceable one, complete all as specified and as directed by Engineer-in-charge. |
| 33 | S&F in repairs 20mm ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 20mm- 210 gms) and fixed in position complete all as per specified and as directed by Engineer-in-charge. |
| 34 | S&F in repair 15 mm bore bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge. |
| 35 | S&F in repair 15 mm bore CP basin mixer for mixing hot & cold water with capstin head screwed down high pressure with or with out littered 'H' or 'C' with long screwed shank and fly nuts screwed down for iron pipe, complete all as per specified and as directed by Engineer-in-charge. |
| 36 | S&F in repair Chromium plated fancy type 15 mm bore stop cock/Angle stop cock cast copper alloy, with crutch or butterfly handle, screwed down, high pressure screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer-in-charge. |
| 37 | S&F in repair PVC connection 15mm dia size with PTMT nuts of length 450mm, complete all as specified and as directed by Engineer-in-charge. |
| 38 | S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms), complete all as specified and as directed by Engineer-in-charge. |
| 39 | S&F in repair Soap dish, vitreous China white, approximatesize 160x 160x90mm fixed to plugs with chromium platedbrass screws, complete all as per specified and as directed by Engineer-in-charge. |
| 40 | M&L for 100mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as per specified and as directed by Engineer-in-charge. |
| 41 | Dismantling water tanks of capacity exc. 500 and not exc. 1000 ltrs, complete all as per specified and as directed by Engineer-in-charge. |
| 42 | S&F rotational moulded polyethylene water storage tanks double layered ISI Marked (cylindrical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position all as specified and directedin SSR Pt I. |
| 43 | S&F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580mm x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and as directed by Engineer-in-charge. |
| 44 | S&F vitreous China wash down water closet pan (pedestal pattern) with seat cover white with 'P' or 'S' trap, including and flushing pipe etc complete including making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing specifications as specified (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed by Engineer-in-charge. |
| 45 | S&F in repair plastic water closet seat cover (any colour to match the EWC) closed pattern with flat bottom and cover, complete all as per specified and as directed by Engineer-in-charge. |
| 46 | S&F cast iron 'P' trap 100 mm bore, complete all as per specified and as directed by Engineer-in-charge. |
| 47 | S&F in repair PVC 10 ltr capacity low level flushing cistern white with inlet ball valve float and braket, complete all as per specified and as directed by Engineer-in-charge. |
| 48 | Supply only 32 mm bore PVC flush pipe for flushing cistern, complete all as per specified and as directed by Engineer-in-charge.Note - Rate of fixing is included in serial item no. 47. |
| 49 | Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge. |
| 50 | M&L for providing 75mm thick PCC 1:3:6 type C2 (40mm graded aggregate) as in plinth protection and paving finishing the surface even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge. |
| 51 | M&L for PCC (1:4:8) type D2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge. |
| 52 | M&L cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in surface channels and drains, complete all as specified and as directed by Engineer-in-charge. |
| 53 | M&L for plain cement concrete (1:2:4), type B1 (using 20mm graded stone aggregate) as in coping, benching and the like incl weathering. slightly rounded and throating etc, complete all as specified and as directed by Engineer-in-charge. |
| 54 | Demolition of reinforced cement concrete of any description and in any position not otherwise specificied provided for, complete all as per specified and as directed by Engineer-in-charge. |
| 55 | M&L for precast cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge. |
| 56 | M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge. |
| 57 | Dismantling of cast iron pipe jointed in cement mortar and taking out of trenches 100mm bore (Excavation to be measured and paid separately) complete all as specified and as directed by Engineer-in-charge. |
| 58 | S&F 100mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches complete all as specified and as directed by Engineer-in-charge. |
| 59 | All as per serial item No. 58 above but pipe is fixed on wall. |
| 60 | S&F cast iron cowls 100mm bore complete all as specified and as directed by Engineer-in-charge. |
| 61 | S&F 100mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge. |
| 62 | S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100mm bore pipe, complete all as specified and as directed by Engineer-in-charge. |
| 63 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge. |
| 64 | Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as per specified and as directed by Engineer-in-charge. |
| 65 | Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge. |
| 66 | M&L for 150mm dia (internal) salt glazed stone ware drain pipes (Grade A) ISI Marked as in sewage lines laid in trenches and jointed complete all as specified and as directed by Engineer-in-charge. |
| 67 | M&L for concrete bed to 150mm dia SWG/RCC drain pipe including packing under & haunching against the sides of pipes with concrete after they are laid & tested in PCC (1:3:6) type C2 (using 40 mm graded crushed stone aggregate)complete all as specified and as directed by Engineer-in-charge. |
| 68 | Taking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators etc and separating serviceable fittings for reuse in the same work and removing unserviceable fittings and fixtures with wiring cable, battens, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc all complete all as specified and directed complete all as per specified and as directed by Engineer-in-charge. |
| 69 | Taking down DB's including MCB's etc., complete all as per specified and as directed by Engineer-in-charge. |
| 70 | Taking down carefully unserviceable sub main wiring of any size / core / type including making good the disturbed surfaces, complete all as specified and as directed by Engineer in Charge. |
| 71 | M&L for Point wiring with PVC un-sheathed and PVC insulated cable with stranded copper conductor FRLSH cable 1.5 Sq mm size 1100V grade in and including PVC casing caping double lock type of size not less than 25X16mm including one No. 1.5 Sq mm single core PVC insulated copper cable for continuous earth wire (green coloured) connected to earth dolly complete for one light /Bell point controlled by one 5 Amp switch one way including factory made PVC modular box sutaible for switch/sockets etc ISI marked and making good disturbed surface of walls & floors etc., complete all as specified and as directed by Engineer in Charge. Note - Wiring shall be circuit type and Nos of conductor in conduit shall be taken as per relevant IS Code. |
| 72 | All as per serial item No. 71 above but for One socket outlet, 3 pin 5/6 Amps, independent Board. |
| 73 | M&L for Point wiring with PVC un-sheathed and PVC insulated cable with stranded copper conductor FRLSH cable 2.5 Sq mm size 1100V grade in and including PVC casing caping double lock type of size not less than 25X16mm including one No. 2.5 Sq mm single core PVC insulated copper cable for continuous earth wire (green coloured) connected to earth dolly complete for socket outlet 15/16 Amps on independent board including factory made PVC modular/ non modular box sutaible for switch/sockets etc ISI marked and making good disturbed surface of walls & floors etc., complete all as specified and as directed by Engineer in Charge. Note - Wiring shall be circuit type and Nos of conductor in conduit shall be taken as per relevant IS Code. |
| 74 | M&L for modular switch one way 10 Amps, 1 module, 240 Volts, complete all as specified and as directed by Engineer in Charge. |
| 75 | M&L for modular socket, 6 Amps - 2/3 pin combined 2 module, 240 Volts, complete all as specified and as directed by Engineer in Charge. |
| 76 | S&F Modular Socket, 6A/16A - 2/3 pin combined, 2 module, 240 Volts, complete all as specified and as directed by Engineer in Charge. |
| 77 | S&F Modular Switch 1 way, 16 Amp, 1 Module type, universal, 240 volts, complete all as specified and as directed by Engineer in Charge. |
| 78 | M&L for modular white cover plate with frame, 3 module, 240 Volts, complete all as specified and as directed by Engineer in Charge. |
| 79 | M&L for modular white cover plate with frame, 8 module, 240 Volts, complete all as specified and as directed by Engineer in Charge. |
| 80 | Supply and fix ceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body, complete all as specified and as directed by Engineer-in-charge. |
| 81 | S&F in repair wall mounted LED Tube light fitting 10 watt surface mounted general purpose LED Batten in Extruded Aluminium housing including making connections with 2 core flexible copper wire 0.50 sqmm from ceiling rose after fixing fitting in position at site on 02 Nos new PVC blocks, complete all as specified and as directed by Engineer in Charge.Make - Havells Cat part No. - LUMILINEPLUSNEOBS10WLED865SPCSSIND or makes as mentioned in \\"List of Makes\\" of Particular Specification of the Tender Documents. |
| 82 | S&F in repair of LED surface mounted decorative Bulk Head fittings 10 watts duly fixed on suitable PVC/ wooden Box and connection, complete all as specified and as directed by Engineer in Charge.Make : Cat Part No. RUGBYGENXFTS10WLED865SSYMBOPC of Havells or makes as mentioned in \\"List of Makes\\" of Particular Specification of the Tender Documents. |
| 83 | M&L for sub-main wiring with two single core 4.0 Sqmm PVC (FRLSH) insulated multistranded flexible copper conductor cable 660/1100 volts grade down in through non-metalic PVC casing caping (25x16 mm) with and including PVC insulated 4.0 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly, complete all as specified and as directed by Engineer in Charge. Note : Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid as one unit. |
| 84 | S&F in repair of Sheet Metal Enclouser, Double door DB, 240 volts, 8 way with 200 Amps rated bus bar Single pole & neutral (SPN) fixing on suitable rectanguler block, duly prewired with thimble of incoming and outgoing wires in DB and good finish to the old disturbed surface, complete all as specified and as directed by Engineer-in-Charge. Note - Taking down to be measured under serial item no. 69. |
| 85 | S&F MCB Single Pole (SP), B-Curve, 230 volts of capacity 6-32 Amp, 10 KA, complete all as specified and as directed by Engineer-in-Charge. |
| 86 | S&F MCB Single Pole & Neutral (SPN), C-Curve, 230 volts of capacity 40-63 Amp, 50 Hz, 10 KA fixed with lugs/thimbles, complete all as specified and as directed by Engineer-in-Charge.Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysOct 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender