Tender For Improvement Of Water Supply Schme Pal Ur Town In Tehsil Pal Ur District Kangra (Hp). (Sh) Providing Supplying Errection Of 7.50 H.P Submersible Pumping Laying Jointing Of Rising Main Near Godrej Showroom Banuri.
Tender Value
2.34 Lakhs
Estimated cost
Bid Submission
19 Sep 2026
4 days left
EMD
4700
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Water Supply Schme Pal Ur Town In Tehsil Pal Ur District Kangra (Hp). (Sh) Providing Supplying Errection Of 7.50 H.P Submersible Pumping Laying Jointing Of Rising Main Near Godrej Showroom Banuri.
BOQ
| Sl. No. | Item Description |
| 1 | Providing, Supplying & errection of submersible pumping set of (KSB/Kalama/Kirloskar/Johnston/Cromption/BS) make conforming to BIS: 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrel case electric induction motor of same make as (manufacturer standard) conforming to BIS:9283-1979 (latest with upto date ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- |
| 2 | A Site Conditions:- |
| 3 | i) Total Head 56.28 |
| 4 | ii) Discharge required from each pump 5.70 LPS |
| 5 | iii) No. of pump required 1.00 sets |
| 6 | iv) Location of the site of installation of machinery The site is located at a distance of 12 Kms from Palampur |
| 7 | v) The altitude of installation Altitude of place is 900 m above MSL |
| 8 | vi) Rate Voltage 415+ 10% |
| 9 | viii) Type water and its source Clear Water |
| 10 | ix) Charactristics of water ---- |
| 11 | a) Ambient Temperature dig.c 20 dig.c b) Turbidity NTU 10 NTU c) Hardness 260 Mg/ltrs (as CaCO3) --- d) PH 7.5 --- e) Total soild Mg/Ltrs --- f) Others --- |
| 12 | x) Depth of Bore Well 60.00 mtrs |
| 13 | xi) LWL in Tube Well 1020.00 mtrs |
| 14 | xii) Dia of Bore 200 mm |
| 15 | Xiii) Maz draw down 6 mtrs |
| 16 | xiv) Static head in Mrs 15 metre |
| 17 | xv) Center line of level of pump 1010 metre |
| 18 | xvi) Discharge level of highest Point 1020 metre |
| 19 | xvii) Static head in Mrs 50 mtrs |
| 20 | xviii) Length of R/Main (Including Column) 40 Rmt. |
| 21 | xviii) Dia of rising main 80 Rmt. |
| 22 | xix) Limits of pump operation (-) 15% to (+) 10 % of total head at duty point |
| 23 | xx) R.P.M of pimp operation 2900 RPM (or to be specified) |
| 24 | xxi) Test run 8 hours continueously for 7 days |
| 25 | Providing and installation of 10 HP automatice panel including auto sarter , auto stop and restart facility schneider starter, automaticecally corrects incoming phase motor duty MC, LED , IND lights single/Three Phase preventer, timer, relay, selector switch auto and manually start stop facility, prevention of phase reversal, imbalance and overload and fixed with compatiblestarter including pannel board complete in all respect with in all lead and lift as per the satisfaction of Engineer-in-charge. |
| 26 | Providing & laying PVC insulated jointless flat water proof copper cable of Siemens/Fenolex/Gloster/ICC make conforming to BIS:1554(Part-1)1988 or latest with upto date ammendments of suitable size for the pump sets offered ( One cable carrying all three phases) including all other electrical equipment accessories such as thimbles, flexible, pipes, solder,nuts & bolts, cable glands etc. laid in pipes or tranches under floor. The type size & Make will be subject to approval of HPSEB authorities. In case of non acceptancy by HPSEB authorities it shall have to be replaced by the tenderer free of cost. |
| 27 | The type , size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. |
| 28 | On supply side of core coper cable 4.00 mm ( From HPSEB Meter to switch to starter) a) Turbidity NTU |
| 29 | Providing and fixing of high steel carbon rope size 5 milimetre square for holding of submersible pump set within all leads and lifts as per the direction of Engineer-in-charge. |
| 30 | Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make cast steel double flanged 80 mm dia sluice valve of class ASA-150 confirming to BIS-1414 (API-600)(to be provided on delivery side ) of equal size to one dia more than the dia of delivery of pump and capable of with standing nominal seat test pressure of 52 kg/cm² complete with in all respect as per the satisfaction of Engineer-in-charge. |
| 31 | Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make cast steel double flanged 80 mm dia swing check type reflux valve having bypass arrangement of class ASA-150 confirming to BIS-1868 (API-600)(latest edition ) to be provided on delivery side)of size one step higher than the delivery size of pump and shall be suitable for withstanding ding nominal seat test pressure of 52 kg/cm² complete with in all respect as per the satisfaction of Engineer-in-charge. |
| 32 | Laying, Column assembly of G.I/MSERW/UPVC/PPR pipes considering site requirements and having appropriate size in accordance with the delivery size of Pumping set. The pipe shall confrom to relevant BIS codes & capable of with standing the feid test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tepers/ reducers, flanges, rubber gaskets 3 mm thick nuts & bolts and any other fitting required at site and work shall be to the entire satifaction of Engineer in change. column assembly =80 dia G.I flanged pipe (medium grade) NOTE:- Actual laying to be done as per final drawings to be approved by the Engineer in charge. |
| 33 | Laying,Jointing and testing in trenches of galvanized iron pipe by way of circumfrentional butt welded 96% joints butt welded & 4% flanged pipes including cost of flanged bends of all degrees confirming to IS 1239-2004 (Medium class) with upto date ammendements) as specified below with plain end and capable of withstanding required test pressure in random lenght of 4 to 6 metres including specials short pieces bends, reducers tees etc. made from parent tube. The butt welded joints as per table below duly welded in three layes (one inner and two outer) with pipes at at both ends as per relevent BIS standards along with nuts and bolts of required sizes confirming to BIS 1364 (with upto date ammendments). The laying of pipe shall include all operational such as cutting welding, jointing, providing & fixing of fabrication of bends, tees required level including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respect to the satisfaction of Engineer-in-charge. The fabricated bends shall have three or four cuts having its radious not less than five times the dia of pipe. (Earth work in trenches to be measured and paid separatly). The welding electrodes shall be as per IS 814 of advani Overlikon/L&T or ISI marked make. a) 80 milimetre dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysSep 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender