Tender For Provn Of Seating Arrangement With Shed At Various Places At Nts (Svp), Teylerabad And special Repair Of Main Gate And Sentry Post At Marcos (Pbr), Teylerabad Under Ge Minniebay, Sri Vijaya Puram ( 8883/E8)
Tender Value
46 Lakhs
Estimated cost
Bid Submission
05 Oct 2026
19 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Seating Arrangement With Shed At Various Places At Nts (Svp), Teylerabad And special Repair Of Main Gate And Sentry Post At Marcos (Pbr), Teylerabad Under Ge Minniebay, Sri Vijaya Puram ( 8883/E8)
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and 15cm deep and getting out in soft/loose soil complete all as directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil complete all as specified. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified. |
| 4 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified. |
| 5 | M&L for PCC 1:4:8 type D-2 (40mm graded) as in foundation filling and mass concrete cComplete all as specified. |
| 6 | M&L precast cement concrete block masonry with solid block, exc 10cm in width in PCC type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified. |
| 7 | M&L for rendering 15mm thick cement plaster on fair faces of concrete block masnory in CM 1:4 (with river sand) mixed with WPC as per manufacture' s instructions, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be measured and paid seperately Note : Water proofing compound shall be measured seprately. |
| 8 | Supply only Liquid water proofing compound |
| 9 | M & L for complete removal of existing treatment and preparation of plastered wall surfaces using mechanical means and removing all fungus, black stains, algae etc and applying two of 100% Premium Acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of WHITE colour with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over old surfaces complete all as specified and as directed by Engineer-in-Charge. Make :- Asian Paints (Apex Ultima), Berger (Weathercoat long life flexo), Nerolac (Excel Total), Shalimar Paints (Weatherpro+ Super Luxury Emulsion). |
| 10 | M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete as specified as directed. |
| 11 | M&L for PCC 1:4:8 type D-2, 100 mm thick using (40mm graded) as sub base Complete all as specified. |
| 12 | Providing and laying vitrified parking tiles of sizes (400X400) of 10-15 mm thickness conforming to IS 15622 in all colors and shades in outdoor floors and skirting meant for parking of cars and trucks, grouting the 3 mm width joints using epoxy grout mix of 0.70 kg of organic coated filler of desired shade including filling/grouting and finishing set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 13 | M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed. |
| 14 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed. |
| 15 | M & L aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering. |
| 16 | M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161- 1979 grade St.-240 complete all as specified and directed. |
| 17 | M & L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed. |
| 18 | M&L for plain cement concrete 1:3:6, Type C-2 using 40mm graded crushed stone aggregate finished even and smooth without using extra cement as in post holes / post placers etc., and plinth protection complete including formwork as required complete all as specified and directed. |
| 19 | S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410 W (Grade E-250) quality A complete all as specified and directed. |
| 20 | S & F Mild steel screw bolts (machine made) of any dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n.exc. 10 cm long complete all as directed. |
| 21 | M&L for Preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed. |
| 22 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as directed. |
| 23 | Supply and fixing stainless steel powder coated bench of SS -304 grade for seating capacity of 03 person at one time of size 1800mm x 680mm x780mm all as specified and directed by Engineer-in-charge. |
| 24 | Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specifed and directed. |
| 25 | M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed. |
| 26 | Dismantling plain or corrugated steel sheeting, any gauge, for roof coverings in small patches all as specified and directed. |
| 27 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complet all as specified and as directed. |
| 28 | M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 29 | Demolition of precast concrete block walling built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed. |
| 30 | M & L for rendering 15 mm thick in cement mortar 1:4 on concrete or brick masonry surfaces and finishing the top surface even and fair complete all as specified and as directed. |
| 31 | M&L for rendering 10mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth complete all as specified and as directed. |
| 32 | M&L preparing newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of primer and including applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed. |
| 33 | Taking down chowkats or frames exceeding 1.5 sq.m and not exceeding 4 sqm each with shutters without taking off shutters from the frames and removing off site etc complete all as specified and as directed. |
| 34 | Taking down chowkats or frames not exceeding 1.5 Sqm (with shutters & grill (if fixed) without taking off shutters from the frame) complete all as specified and directed. |
| 35 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 36 | M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 37 | Supply only sheet glass, 4.8 mm ordinary quality and glazing with oil putty in square in n.exc 0.5 sq.m in each pane complete all as specified and as directed |
| 38 | Supply only HDF boards, 12 mm thick medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and as directed. |
| 39 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 40 | M & L RCC M-30 (nominal mix) as in beams, tie beam, gable beam cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. |
| 41 | Formwork to sides and soffits of floor or roof beams, tie beam, gable beam, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. |
| 42 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 43 | M&L TMT bars 5 to 8 mm mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia as in stirrups complete all as specified and directed. |
| 44 | Dismantling boarding, of any description, fixed in any position with nails complete all as specified and directed. |
| 45 | Supply and fixing Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including 10m thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of G.I frame work as per specification and drawing complete all as specified and directed. |
| 46 | Providing, supplying, fabricating and fixing Aluminium Composite Panels (ACP) of exterior grade, consisting of two aluminium skins of minimum 0.50 mm thickness each bonded to a fire-retardant mineral-filled core, with overall panel thickness of 4 mm, finished with 25 micron PVDF (Kynar 500/Hular 5000) coating on the external face and service coating on the internal face, in approved colour and shade, UV resistant and weatherproof, suitable for facade / cladding sealants, cutting, bending, routing, fixing in true line and level, allowing for thermal movement, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge, including all labour, materials, tools, accessories, scaffolding and incidentals, with minimum 10-15 years manufacturer warranty, complete in all respects. |
| 47 | M & L for preparation of old or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specifed and as directed. |
| 48 | S & F in repair Vitreous China urinals, bowl decorative type type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) |
| 49 | S&F in repairs stop valves/angle valve cast copper alloy chromium plated with long shank and cup fancy type screwed down high pressure screwed both ends for pipe or union fixed for 15mm bore,including necessary cutting and making good wall or floor tiling to match existing(tiles to be paid supplied only rates) etc complete all as specified and as directed. |
| 50 | Supplying and Laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with outer dia 20mm including taking down complete all as specified. |
| 51 | Supply only PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed. |
| 52 | S&F in repairs PVC flexible waste pipe heavy duty of 32 /40 mm for wash hand basin and Kitchen sink complete all as specified and directed. |
| 53 | S & Fixed in repair for 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or tin floors complete all as specified and directed. |
| 54 | S & F for 110 mm dia pvc (SWR) bend any radius complete all as specified and directed. |
| 55 | M&L for taking down carefully existing aluminium point wiring (light, fan, socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed. |
| 56 | M&L for taking down carefully existing old DBs and making good disturbed surfaces of walls to match the existing surfaces complete all as specified and as directed |
| 57 | M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified and as directed. Please Enable Macros to View BoQ information |
| 58 | M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender