Tender For special Repair To Single Officer Living Building No P-78 Of 40 Fd And Other Sanctiond Work In The Area Of Agr Br-I At Bikaner Mil Stn Under Ge (N) Bikaner.
Tender Value
46 Lakhs
Estimated cost
Bid Submission
01 Oct 2026
13 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bikaner → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Single Officer Living Building No P-78 Of 40 Fd And Other Sanctiond Work In The Area Of Agr Br-I At Bikaner Mil Stn Under Ge (N) Bikaner.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of reinforced cement concrete to any thickness as in slabs, beams incl cutting of reinforcement as reqd at site complete all as specified and directed. |
| 2 | Demolition of lime Concrete to any thickness in any position incl all topping thickness (below or above ground level) complete all as specified and directed. |
| 3 | Dismantling Bricks (laid flat or on edge) or brick tiles in floors,roof, channels, kerbs, aprons, etc. (each layer) laid bedded and pointred in any type of mortar complete all as specified and directed. |
| 4 | Demolition cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 5 | Taking down cement plaster, any description on brick or stone or cement concrete walls including any tiles and raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 6 | Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost complete all as specified and directed. |
| 7 | Taking down shutter exc 1 sqm and not exc 2 sqm each and refixing in the same opening after rescuring or easing & adjustment complete all as specified and directed. |
| 8 | Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and romoving to store complete all as specified and directed. |
| 9 | Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish complete all as specified and directed. |
| 10 | Demolition of brick/stone masonry built in CM complete all as specified and directed. |
| 11 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 12 | M&L brick work with fly ash bricks straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed. |
| 13 | M&L half brick work with fly Ash bricks straight or curved on plan to any radius built in CM 1:4 all as specified and directed. |
| 14 | M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified. |
| 15 | M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately). |
| 16 | M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified. |
| 17 | M&L for Rendering 5 mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified. |
| 18 | M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular ) in floors ,area of each tile exc 0.11 sqm but n.exc. 0.18 sqm set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 20 mm thick screed plaster in CM 1:4 complete all as specified and directed |
| 19 | M&L Glazed ceremic colour tiles in vertical surfaces 300x600x7/8 mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete etc all as specfied and directed. |
| 20 | M&L for 7-8 mm thick light shade double charged Vitrified ceremic tiles (Square/Rectangular) polished ,area of each tiles exc 0.42 Sqm but not exceeding 1.00 Sqm as in floors over 20 mm thick screed in CM 1:4 jointed in neat cement slurrry and pointed in white cement grout to match the shade of existing surfaces complete all as specified and directed. |
| 21 | ditto as per Serial item no 20 above but with 10 mm thick in CM 1:4 as on vertical surface complete all as specified and directed. |
| 22 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified and as directed. |
| 23 | M&L for Granite (of any type and any colour)work 20mm thick( table rubbed and polished)in cooking plateform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab including cutting and polishing etc. complete all as specified and as directed. |
| 24 | M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement complete all as specified and directed. |
| 25 | Mild steel framed work such as grills, gratings, tank staging etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks, Angle frame,cooler stand and similar work conforming to Fe 290 Gd E-165 complete all as specified and directed. |
| 26 | M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 27 | M&L for TMT bars 6mm to 8mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia complete all as specified and directed. |
| 28 | M&L for TMT bars 5 mm to 10 mm dia in reinforcement, cut to length, bent to shape required as in stirrups and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 29 | M&L for reinforced cement conc M-25 Design mix as in slab supported on walls , beam, and columns in floors,roofs landings , balconies etc. complete all as specified and directed. |
| 30 | M&L for reinforced cement conc M-25 Design mix as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 31 | M&L for reinforced cement conc M-25 Design mix as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 32 | M&L for Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded cdrushed stone aggregate) as in chajjas incl necessary formwork and the like, complete all as specified and directed.. |
| 33 | Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete, complete all as specified and directed. |
| 34 | Form work to sides and soffits of roof beams incl supports over hangs etc finished rough complete all as specified and directed. |
| 35 | Form work to edges of concrete flats, breaks, conc railing nexc 200mm wide finished roughthick complete all as specified and directed. |
| 36 | Formwork to sides of square/Rectangular etc pillars, posts, struts, piers,columns, and stanchions rough finish complete all as specified and directed. |
| 37 | Supply only water proofing compound complete all as specified and directed. |
| 38 | Cleaning of surface of loose dust and grit and cement slurry etc. by means of wire brush dust removing and scrapper etc .Pot holes/cracks shall be repaired with cement admixed with polymer as per manufacturer instructions complete all as specified and directed. |
| 39 | Providing PCC coving /gola along vertical parapets of size 75 mm x 75 mm with concrete mix (1:2:4) type B1 using WPC of approved make etc complete all as specified and directed. |
| 40 | The surface shall be treated with PU Elastoseal primer with Epoxy primer to seal the pores and enhance the adhesion of the coating,supplying and applying single component waterproofing liquid membrane based on pure,elastomeric,polyurethane resin cold applied of spray/brush applied membrane with an elongation of (650%+,- 50 ) and tensile strength not less than 2 Mpa ,crack bridging ability not less than 2 mm.No leakage upto 5 bars of water pressure.shore hardness > 50 shore. The Minimum thickness to be applied shall be 1.5 mm,( overall )in two layers (each layer 750 micron) or as per manufacurer's instructions so as acheive thickness not less tha 1.5 mm complete all as specified and directed. |
| 41 | Providing and laying of protective Geotextile fabric 150 GSM over the entire membrane with proper overlaps of 75 mm complete all as specified and directed. Note :- For Roof Treatment process Make of PU Primer /Membrane :- SIKA/BASF,BERGER/STP FOSROC/ SAINT GOBIN /PIDILITE |
| 42 | Providing and laying SRI (Sun Resistance Index ) roof tiles (size 300x300x9-10 mm) with 20 mm thick cement plaster in CM (1:4) mixed with liquid WPC as per manufacturer's instructions confirming to required slope complete all as specified and directed. Note :- For Roof Treatment process Make of PU Primer /Membrane :- SIKA/BASF,BERGER/STP FOSROC/ SAINT GOBIN /PIDILITE |
| 43 | M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in mud stops or roof kerbs, etc complete all as specified and directed. |
| 44 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified and directed. |
| 45 | Supply and fixed Factory made solid PVC Moulded door shutter, 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm plain clour PVC sheet on back face, with wood free EPS, fixing as per specification & drawing complete all as specified and directed. |
| 46 | Supply and fixing of 100 mm But hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 47 | S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed. |
| 48 | S&F for 150mm size aluminium anodised handle of fabricated type and fixed complete all as specified and directed. |
| 49 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor overall length of cover plate 150 mm complete all as specified and directed. |
| 50 | Hacking out old broken glass (any thickness size quality or desc.)from wooden frames or stone conc. or brick surrounds glazed with putty or fixed with beads complete all as specified and directed. |
| 51 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 52 | S&F as in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 53 | S&F in repair 20 mm dia steel curtain rod chromium plated incl brackets, stops etc. complete all as specified and directed. |
| 54 | S&F aluminium haspen stapple incl bolt to hinge plate 100 mm long complete all as specified and directed. |
| 55 | S&F extruded anodised aluminium handle 100 mm long bright polished complete all as specified and directed. |
| 56 | S&F 18/19 mm thick single side Pre laminated PVC Boards suitablely fixed in kitchen cabinets/Cupboards,frames, partitions and shelves of built in cup boards,almirahs and similar work including suitable Piano hinges etc. of any finish complete all as specified and as directed. |
| 57 | M&L for welding in repairs n.exc 2.5 cm in length and not exceeding 6mm thick of metal complete all as specified and directed. |
| 58 | S&F powder coated aluminum frames/shutter ,other sections for doors , windows , ventilators with one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc, complete all as specified and directed. |
| 59 | S & F in repair aluminium glazing clip with rubber gasket of suitable size and thickness as required at site for fixing glass in aluminium door/windows complete all as specified and directed. |
| 60 | S&F sheet glass 5.5 mm thick ordinary quality & glazing with rubber gasket in squares exc 0.5sqm in each pane as in aluminium door/window/Ventilator etc. complete all as specified and directed. |
| 61 | S&F anodised aluminum American handle cast type 200mm for doors all as spfd. complete all as specified and directed. |
| 62 | S & F in repair for door closer hydraulically regulated , designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 KG and fixed complete all as specified and directed. |
| 63 | S&F in repair brass 4 lever mortice lock, vertical type size 100mm suitble for existing aluminium door complete all as specified and directed. |
| 64 | S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover, govering pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed. |
| 65 | Supply and laying of CPVC pipes (outer dia 20 mm) SDR 11 pipes & plain CPVC SDR 11 fittings on wall/ceiling or laying in floors including taking up or down of existing pipe / tubing complete all as specified and directed. |
| 66 | Supply and laying of CPVC pipes (outer dia 25 mm) SDR 11 pipes & plain CPVC SDR 11 fittings on wall/ceiling or laying in floors including taking up or down of existing pipe / tubing complete all as specified and directed . |
| 67 | M&L for RCC pillarrs in PCC 1:2:4 type B-1 set in cement mortar 1:4 moulded 100 x 100mm x 75cm long precast complete all as specified and directed. |
| 68 | M&L Providing cement concrete RCC jalli 35mm thick type B0 1:2:4 using 12.5mm graded aggregate (measured solid) including all mouldings but exc frame,set in CM (1:4) all as spfd complete all as specified and directed. |
| 69 | Jodhpur stone of roof slab self faced 1.5cm to 10 cm thick 25 to 35 cm wide hoisted and set jointed and grouted in cement and sand mortar 1:6 complete all as specified and directed. |
| 70 | M&L Sand stone slab 25-35mm thick as in chhajas, sunshade , man holes covers ,plateform etc. n exc 2 m in length punched dressed on face and along exposed edges,self faced on other side and set in cement mortar 1:4 incl. making chases in wall complete all as specified and directed. |
| 71 | M&L PCC 1:3:6 type C-2 using 40mm graded stone agg. ,50mm thick as in floors over stone patti slab etc. finished the surface even and fair complete all as specified and directed. |
| 72 | S&F in repair rotational mouleded polythene water storge tank any colour triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as specified of 500 ltr capacity include dismantling old water tank and remove from site complete all as specified and directed. |
| 73 | S&F in repair 20 mm dia of ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed, (minimum weight 20mm-210 gms) complete all as specified and directed. |
| 74 | S&F in repairs,stop cock with butterfly handle ,screwed both ends for iron pipe of dia 20 mm complete all as specified and directed. |
| 75 | S&F in repairs wall hung water closet ( size 510x365x380 mm) of superior quality including all fitting fixtures concealed cistern etc. complete all as specified and as directed. |
| 76 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including brackets & waste pipe etc complete all as specified and directed. |
| 77 | S&F in repair 15 mm bore Brass CP WHB/Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 78 | S&F in repair chromium plated Bib Tap, with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia complete all as specified and directed. |
| 79 | S&Fin repair 15mm bore PVC connection with PTMT nuts length 450 mm complete all as specified and directed. |
| 80 | S&F in repair fancy type chromium plated stop valve/Angle valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm complete all as specified and directed. |
| 81 | S & F in repairs health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connections complete all as specified and directed. |
| 82 | S&F CP toilet paper holder fancy type complete all as specified and directed. |
| 83 | S&F Towel ring of cast copper alloy chromium plated complete all as specified and directed. |
| 84 | S & F in repairs Chromium plated shower rose minimum125 mm size with or without swivel joints, any size, including fixing to steel pipe or unions complete all as specified and directed . |
| 85 | S&F 5 mm thick looking mirror of selected quality with and including stainless steel spacers any size as approved by Engrbevelled edge mirror of selected quality glass mounted on 6mm th AC building board or commercial ply complete all as specified and directed. |
| 86 | S&F in repair 32 mm size PTMT waste coupling (half or full threaded) and Brass CP bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing union and cap complete all as specified and directed. |
| 87 | S&F in repair CP soap dish 100x150mm complete all as specified and directed. |
| 88 | S&F PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints fixed with lubricants laid in trenches or in floors including taking down of existing CI/PVC pipe complete all as specified and directed. |
| 89 | S&F PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints fixed with lubricants laid in trenches or in floors including taking down of existing CI/PVC pipe complete all as specified and directed. |
| 90 | S&F PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints fixed with lubricants fixed to walls including suitable stack clamps including taking down of existing CI/PVC pipe complete all as specified and directed. Note: Pipe should be fixed through brackets keeping them 100 mm away from wall. |
| 91 | S&F PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints fixed with lubricants fixed to walls including suitable stack clamps including taking down of existing CI/PVC pipe complete all as specified and directed. Note: Pipe should be fixed through brackets keeping them 100 mm away from wall. |
| 92 | S&F PVC (SWR) vent cowl for 75 mm dia pipe complete all as specified and directed. |
| 93 | S&F PVC( SWR) bends (any radius) / Reducers/ Couplers/Sockets etc. 110 mm bore complete all as specified and directed. |
| 94 | S&F PVC( SWR) bends (any radius) / Reducers/ Couplers/ Sockets etc. 75 mm bore complete all as specified and directed. |
| 95 | S&F PVC(SWR) Branch pieces, single or Double T/Y, equal or unequal 110 mm bore complete all as specified and directed. |
| 96 | S&F PVC(SWR) Branch pieces, single or Double T/Y, equal or unequal 75 mm bore complete all as specified and directed. |
| 97 | S&F PVC(SWR) 75 mm bore floor trap plain with grating including jointing with solvent complete all as specified and directed. |
| 98 | S&F PVC(SWR) gully trap 125/110 mm setting and jointing with solvent complete all as specified and directed. |
| 99 | M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 100 | M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width & girth & applying one coat of synthetic enamel paint complete all as specified and directed. |
| 101 | M&L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width and grith and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 102 | M&L for for complete removal of existing treatment on walls etc, by scraping, sand papering or by using mechanical sander/grinder etc. and preparing surfaces and applying a coat of wall care putty and a coat of wall primer and two coat of oil emulsion distemper/OBD of approved tint on walls by using roller/spray machine complete all as specified and directed. |
| 103 | M&L for preparation of new plastered/putty surfaces by brooming down or steel wire brushing scraping down oil & greasy spots etc and applying two coats oil emulsion distemper/OBD paint of approved tint on walls over a coat of wall care putty and a coat of wall primer by using roller/spray machine over new surfaces etc complete all as specified and directed. |
| 104 | M&L for preparation of new plastered/putty surfaces by brooming down or steel wire brushing scraping down oil & greasy spots etc and applying one coat of primer and applying two coats oil emulsion distemper/OBD on ceiling of approved tint over new surfaces by using roller/spray machine etc all as specified and directed by Engineer-in-Charge. |
| 105 | M&L for preparation of new plastered/putty surfaces , brooming down or steel wire brushing etc applying two coat of exterior acrylic emulsion paint (weather coat ) of approved tint on walls a coat of wall care putty and a coat of wall primer by using roller/spray machine over new surfaces etc complete all as specified and directed. |
| 106 | M&L for for complete removal of existing treatment on walls etc, by scraping, sand papering or by using mechanical sander /grinder etc. and preparing plastered surfaces and applyinga coat of wall care putty and a coat of wall primer and two coat of exterior acrylic emulsion paint (weather coat ) of approved tint on walls by using roller/spray machine complete all as specified and directed. |
| 107 | Structural design for roof slab, beams, chajjas and other connected RCC members required to be reconstructed under this schedule with & including vetting of structural design from approved Govt Engineering College/NITTTR/CBRI, complete all as specified and as directed:Notes:(i) Tenderer shall cary out the site visit to ascertain the size of slab, other RCC members, arrangement of rooms, etc required for design purpose.(ii) Four sets of structural drawing shall be provided to GE by Contractor duly vetted as above. |
| 108 | M&L for 75mm thick PCC (1:4:8), type C2 using 40mm graded stone agg as in sub base of floors etc finished even and rough complete all as specified and directed. |
| 109 | Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade to IS 15658-2006 manufactured using grey cement and pigment complete all as spcified and directed. |
| 110 | M&L for 25 mm thick sand filling under floors, cushning under interlocking tiles or in foundations complete all as specified and directed. |
| 111 | Excavation in trenches not exc 10 Sqm on plan not exc 1.5 m deep and not exc 1.5 m wide , getting out in any type of soil complete all as specified and directed. |
| 112 | Returning filling in incl spreading levelling watering and well ramming in layers not exc 25cm thickness complete all as specified and directed. |
| 113 | Removing excavated soil to a distance n exc 50m and depositing at alevel not exc 1.5m above the starting point complete all as specified and directed. |
| 114 | M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregats as in bed to 150mm drain pies incl packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 115 | S&F Salt glazed stone ware drain pipe 150mm bore in trenches and jointed complete all as specified and directed. |
| 116 | M&L Brick work in cement mortar (1:4) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius complete all as specified and directed. |
| 117 | M&L Rendering 15mm thick in CM 1:4 concrete walls or stone masonary walls surfaces as in wall finishes even and smooth w/o using extra cement complete all as specified and directed. |
| 118 | M&L for PCC type B1 (1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like incl form work complete all as specified and directed. |
| 119 | M&L Precasted RCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in drain/ manhole covers set in cement mortar1:4 complete all as specified and directed.(Note : Slab covers shall be floated with surface vibrator,and over turfed base ,arrandement for turfed base has to be from contractors side) |
| 120 | M&L for preparation of new surfaces plastered by brooming down or steel wire brushing scraping down oil & greasy spots etc and applying and applying three coats white wash over new plastered surfaces complete all as specified and directed. |
| 121 | Surface excavation (not exceeding 30cm deep) and averaging 15 cm , getting out in soft / loose soil complete all as specified and directed. |
| 122 | M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete complete all as specified and directed. |
| 123 | M&L 40 mm thick for damp course to horizontal surfaces in cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate incl all necessary form work complete all as specified and directed. |
| 124 | S&F factory made mild steel Window/Ventilator box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking arrangement and one shop coat of red oxide primer complete all as specified and directed.Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided |
| 125 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n exe 0.5 sqm each pane complete all as specified and directed. |
| 126 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished smooth and even without using extra cement complete all as specified and directed. |
| 127 | M&L for hardcore of gauge nexc 63mm , deposited , spread and levelled in layers nex 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 128 | M & L Sand filling under floors or in foundations including watering and consolidation all as specified and directed. |
| 129 | M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges where directed and providing 6 mm thick joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand (all by weight) complete all as specified and directed. |
| 130 | M&L for 40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in plinth protection and chajjas complete all as specified and directed. |
| 131 | M&L for preparing new plastered surfaces and applying two coats of cement base paint on surfaces of walls complete all as specified and directed. |
| 132 | M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed. |
| 133 | M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed. (Note - Colour as approved By Garrision Engineer) |
| 134 | M&L steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240.complete all as specified and directed. |
| 135 | S&F Mild steel bolts of any length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed . |
| 136 | M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, ladders etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Gde Fe410-0 or Fe 310-o complete all as specified and directed. |
| 137 | M&L for 75mm thick PCC(1:2:4) type B2 as in floor laid in alternate panels finished even and smooth with out using extra cement complete all as specified and directed |
| 138 | S&F plates Fe-410-W(Gde E-250) quality A (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement complete all as specified and directed. |
| 139 | Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 140 | M&L for providing and laying 80mm thick factorymade chamfered edge cement concrete paveblock of M-35 grade with approved colourdesign & pattern as in footparth, parkslawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method usingPU mould, laid in required colour & patternover and including 50mm thick compactedbed of fine sand, compacting and properembedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand andcutting of paver blocks as per required sizeand pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 141 | Excavating in post holes (or similar holes) each not exc 0.50cum and getting out in loose /soft soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer not exc 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed. |
| 142 | M & L for PCC (1:3:6) type C2 using 40mm graded stone aggregate in foundation/filling and mass concrete complete all as specified and directed. |
| 143 | M&L two coat of cement base paint on newly plastered surface of walls including a priming coat of primer for preparation of surface complete all as specified and directed. |
| 144 | M&L Post and struts in fencing incl. cutting top to shape as directed , drilles holes, notching of wire etc. flat iron fillets for securing wiremess including all necessary drilling,welding,bilting or riviting etc and conforming to Fe 290 (Gde E-165) complete all as specified and directed. |
| 145 | S&F MS flat iron 50x6mm / 40x3mm to secure chain link fencing and wind ties for roof including securing bolts/screws complete all as specified and directed. |
| 146 | S & F mild steel Round bars 10mm dia and over Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde -E-165) cut to length, bent to shape required, including cracking, bending , hooking endsand fixing with nut bolt to angle iron post etc complete all as specified and directed. |
| 147 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc incl provision of binding wire complete all as specified and directed. |
| 148 | Supply only MS galvanised wire 3mm dia & Nominal mesh size of 50X50 mm as in chain link fencing etc complete all as specified. Note : weight of wiremesh will be decided through BOO ordered by GE |
| 149 | M&L for PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching includind weathering slightly rounded chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair and the like complete all as specified and directed. |
| 150 | Excavating over area, exc 1.5 m but not exc 3.0 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,beyond the first 1.5 m etc.getting out in soft /loose soil complete all as specified and directed. |
| 151 | S&F Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed . |
| 152 | M&L for 50mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) crushed stone aggregate as in stone roof slab as levelling course complete all as specified and directed. |
| 153 | S&F PVC (SWR) pipes 110mm bore single sockted in any length with PVC vent cowl complete all as specified and directed. |
| 154 | M&L for construction of Soakage wells of size 3.6 mtr dia and 6.0 mtr effective depth excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats complete all as specified and directed. (As per Drg BTD 830 Sheet 1/1) |
| 155 | Dismantling of RCC in Chajjas complete all as specified and directed. |
| 156 | M&L for 100mm thick Cement concrete 1:2:4 type B2 using 40mm graded stone aggregate in sub base complete all as specified and directed. |
| 157 | M&L Non skid Ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 158 | M&L coloured non skid Glazed earthenware tiles (Endura tile of Johnson or Equivalent) 149mmx 149mm (or 152.4mm x 152.4 mm) x 6mm or 300mmX300mmx10mm (size approved by the Engineer-in-charge) thick heavy duty endura tiles, in floors, parking etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement and sand mortar 1:6 complete all as specified and directed. |
| 159 | M&L for providing,Laying and fixing PPGI roof covering with aluminium zinc alloy coating of 150gm/Sqm in Mangalore Tile Pattern/Profile(The profile shall exactly resemble traditional mangalore tiles with distinct steps and ridges), having a total coated thickness of 0.50mm with a base metal strength of Minimum 550 Mpa conforming to IS 14246 and IS 1513. The sheet shall be fixed to the existing steel purlins/runners using self tapping screws with EPDM washers or heavy duty galvanised iron J Boltts,nuts and bitumen washers and sealing joints where necessary complete all as specified and directed. |
| 160 | M&L for providing,laying and fixing matching PPGI Steel Ridges and Hips in Mangalore tile profile/pattern with aluminium zinc alloy coating of 150gm/Sqm having a total coated thickness of 0.50mm with a base metal strength of Minimum 350 Mpa conforming to IS 14246. The ridge section shall have a minimum overall girth of 450mm and the sections shall be fixed with securely through the crest of the roofing sheet into the underlying structure purlins using self tapping screws fitted with EPDM Washers, including establisshing a minimum 150mm end lap between ridge/hip pieces, sealing of laps with silicone weather sealant to ensure a watertight joint complete all as specified and directed. |
| 161 | M&L for Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement but including liquid water proofing compound as per manufaturers instruction complete all as specified. Note :-water proofing compound will be paid seperately. |
| 162 | M&L for 75mm thick Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, , finished even and smooth using extra cement , laid in panels including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed. |
| 163 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete including all fittings as per architectural drawings complete all as specified and directed. |
| 164 | S&F of 4.8mm thick Sheet glass frosted on one side, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and directed. |
| 165 | S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel designer ceiling pre finished conforming to IS 14862 (type B category three) incl Powder coated GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete all as specified and directed. (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster) |
| 166 | Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 167 | M&L for 100 mm thick PCC 1:4:8 type D2 (using 40 graded stone aggregate) as in sub base complete all as specified and directed. |
| 168 | M&L for 100 mm thick PCC 1:2:4 type B2 (using 40 graded stone aggregate ) as in sub base complete all as specified and directed. |
| 169 | M & L for machine pressed precast concrete interlocking paver block colour rubber moulding any shape and size with Grey cement and pigment confirming to IS-15658-2006 of 80 mm thickness, M-40 grade complete all as specified and directed. |
| 170 | M&L providing precast cement concrete type B0 1:2:4 (using 12.5 mm graded stone aggregate) for coping including necessary formwork complete all as specified and directed. |
| 171 | Supply, laying and jointing GI tubes, medium grade 40 mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches/wall complete all as specified and directed. |
| 172 | S&F GI reducing Tee ,heavy duty , ISI marked , of any size to 40mm size for connection of 40 mm receiving pipeline from any size water supply line with all threading , jointing material ,testing and comissioning complete all as specified and directed. |
| 173 | S&F GI reducing Tee , heavy pattern 40mm X 25mm for branch connection complete all as specified and directed. |
| 174 | S&F for GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed. |
| 175 | S&F on walls and ceiling or laid in floor/in trenches and jointing GI tubes, 20 mm dia medium grade in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete all as specified and directed. |
| 176 | Cutting existing steel tubing for alterations or additions done in position without taking down for 100 to 20 mm dia pipe (Each cut measured) complete all as specified and directed. |
| 177 | S&F Gun metal gate valve 20mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed. |
| 178 | Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed. |
| 179 | Taking down old U/S existing DB SPN 8 way & TPN DB 4 way including MCB/MCCB/sheet metal Enclosure (Industrial plug socket) of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 180 | Taking down old U/S existing DB SPN 8 way & TPN DB 4 way including MCB/MCCB/sheet metal Enclosure (Industrial plug socket) of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender