Tender For Standing Order For Carrying Out General Civil, Work On Call Up Basis At Hbls Integrated Sugar Plant At Lauriya, West Ch Aran, Bihar.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
28 Sep 2026
15 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pashchim Champaran → Bihar
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Standing Order For Carrying Out General Civil, Work On Call Up Basis At Hbls Integrated Sugar Plant At Lauriya, West Ch Aran, Bihar.
BOQ
| Sl. No. | Item Description |
| 1 | EXCAVATION IN EARTH UPTO 1.5 M: Excavation for foundation upto required depth below existing ground level up to 1.5 m. depth in any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, trenches/plinth beam etccompacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete. The measurement of the excavation would be based on actual depth of excavation with applicable rate for different depths. |
| 2 | EXCAVATION - 1.5 TO 3 M: Excavation for foundation upto required depth below ground level in any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, foundation, trenches/plinth beam etc compacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete . The measurement of the excavation would be based on actual depth of excavation with applicable rate for different depths.EXCAVATION IN EARTH BETWEEN 1.5 TO 3 M |
| 3 | EARTH FILLING: Supply and filling imported earth of approved quality in layers not exceeding compacted thickness of 200mm incl. Watering ,ramming, compacting, and if required, rolling and re-rolling with power roller , mechanical compactors of 80KN- 100 KN capacity to achieve maximum compaction, all complete as per direction of Engg.-In-Charge. The earth should be free from weeds, grass and other objectionable debris. Black Cotton soil shouldn't be used. Measurement basis compacted thickness only. Rate shall include conducting compaction test as per tech spect. |
| 4 | PCC 1:4:8:Providing and laying PCC 1:4:8 using 40 mm and down size graded stone aggregates including machine mixing, providing formwork if required, placing, compacting by hand ramming , curing etc complete. |
| 5 | PCC 1:3:6: Providing and laying PCC 1:3:6 using 20 mm and down size graded stone aggregates including machine mixing, providing formwork if required, placing, compacting by hand ramming, curing etc complete. |
| 6 | PCC 1:2:4.: Providing and laying PCC 1:2:4 using 20 mm and down size graded stone aggregates including machine mixing, providing formwork if required, placing, compacting by hand ramming, mechanical vibrators, curing etc complete. |
| 7 | PCC WORK-1:1.5:3: Providing and laying PCC 1:1.5:3 using 20 mm and down size graded stone aggregates including machine mixing, providing formwork if required, placing, compacting by hand ramming, mechanical vibrators, curing etc complete. |
| 8 | RCC1:1.5:3-FOOTING/PILE CAP :Providing , mixing and placing REINFORCEMENT CEMENT CONCRETE 1:1.5:3 mix using 20 mm and down size graded crushed aggregate including providing and fixing necessary plywood /steel shuttering , scaffolding, bracing, machine mixing, compacting by vibrators, curing, hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. Concrete conforming to relevant specifications of IS 456 - Latest Edn. |
| 9 | RCC 1:1.5:3 -COLUMNS / BEAMS: Providing , mixing and placing REINFORCEMENT CEMENT CONCRETE 1:1.5:3 mix using 20 mm and down size graded crushed aggregate including providing and fixing necessary plywood /steel shuttering , scaffolding, bracing, machine mixing, compacting by vibrators, curing, hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. Concrete conforming to relevant specifications of IS 456 - Latest Edn. RCC 1:1.5:3 FOR COLUMNS / BEAMS |
| 10 | RCC1: 1.5:3ROOF SLAB/CHAJJA: Providing , mixing and placing REINFORCEMENT CEMENT CONCRETE 1:1.5:3 mix using 20 mm and down size graded crushed aggregate including providing and fixing necessary plywood /steel shuttering , scaffolding, bracing, machine mixing, compacting by vibrators, curing, hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. Concrete conforming to relevant specifications of IS 456 - Latest Edn. FOR ROOF SLAB & CHAJJA |
| 11 | RCC 1:1.5:3 FOR CULVERT SLAB: Providing , mixing and placing REINFORCEMENT CEMENT CONCRETE 1:1.5:3 mix using 20 mm and down size graded crushed aggregate including providing and fixing necessary plywood /steel shuttering , scaffolding, bracing, machine mixing, compacting by vibrators, curing, hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. Concrete conforming to relevant specifications of IS 456 - Latest Edn. RCC 1:1.5:3 FOR CULVERT SLAB |
| 12 | RCC 1:2:4 DRIVEWAY, WITHOUT DEWATERING:Providing and laying 150mm thick RCC driveway with 1:2:4 nominal mix using 20mm and down size crushed stone aggregates in panels using slotted MS channel shuttering, machine mixing, vibrating with screed board vibrator, pond curing for 14 days,Concreting shall be carried out as per IS 456 Rate shall also include providing approved quality polythene paper below the driveway, constructing horizontal and longitudinal vatas with 1:10 CM for curing, levelling depressions if any in the base with 20mm stone aggregates and stone dust..Testing of cube, reinforcement steel, stone aggregates, sand, cement etc. to be carried out by contractor at no extra cost.Tubing, ducting, trenching and other necessary embedded items in concrete shall be checked with architect/HPCL representative before concreting.Grooves shall be cut in the RCC driveway and same shall be filled with Bitumen at no extra cost.Rate shall be excluding reinforcement steel which shall be paid separately. but without vaccum dewatering and power trowelling with 1:2:4 nominal mix. |
| 13 | RCC 1:1.5:3 DRIVEWAY, WITHOUT DEWATERING:Providing and laying 150mm thick RCC driveway with 1:1.5:3 nominal mix using 20mm and down size crushed stone aggregates in panels using slotted MS channel shuttering, machine mixing, vibrating with screed board vibrator, pond curing for 14 days,Concreting shall be carried out as per IS 456 Rate shall also include providing approved quality polythene paper below the driveway, constructing horizontal and longitudinal vatas with 1:10 CM for curing, levelling depressions if any in the base with 20mm stone aggregates and stone dust..Testing of cube, reinforcement steel, stone aggregates, sand, cement etc. to be carried out by contractor at no extra cost.Tubing, ducting, trenching and other necessary embedded items in concrete shall be checked with architect/HPCL representative before concreting.Grooves shall be cut in the RCC driveway and same shall be filled with Bitumen at no extra cost.Rate shall be excluding reinforcement steel which shall be paid separately. but without vaccum dewatering and power trowelling with 1:2:4 nominal mix. |
| 14 | REINFORCEMENT STEEL: Supply ,fabrication, hoisting and placing in position HYSD reinforcement bars conforming to IS1786 -Latest Edition Minimum Grade FE 415 or higher grade TMT bars of same grade as per detailed drawing and specifications including cutting, bending, cranking and tying with 18 SWG black annealed binding wire complete. The rates shall be applicable for all heights and depths. Payment shall be made as per reinforcement drawings and with theoretical weights only including all authorised laps. No paymenst shall be made for chairs, spacers & hooks.Weight of Binding wire shall not be considered for payment. |
| 15 | BRICK MASONRY SUBSTRUCTURE: BRICK MASONRY WORKS :Providing and constructing following brick masonry in CM 1:5 using first quality bricks of Class designation 35 (35 KG / SQCM minimum) and conforming to IS-1077-1986 including providing all openings and projections , raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior to use and curing etc complete as per specifications. |
| 16 | BRICK MASONRY SUPERSTRUCTURE: BRICK MASONRY WORKS :Providing and constructing following brick masonry in CM 1:5 using first quality bricks of Class designation 35 (35 KG / SQCM minimum) and conforming to IS-1077-1986 including providing all openings and projections , raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior to use and curing etc complete as per specifications but for superstructure above Plinth level including scaffolding. |
| 17 | BRICK MASONRY:SUBSTR-OLD : same as ITEM 49RU000031, but using old bricks lying at site provided free of cost |
| 18 | BRICKMASONRY:SUPERST-OLD: same as ITEM 49RU000032, but using old bricks lying at site provided free of cost |
| 19 | BRICK ON EDGE: Providing & laying brick on edge for pathways with bricks having minimum crushing strength 75 Kg/Cm2 . Bricks shall be laid on edges as per the design pattern & instruction on 12mm thick cement mortar 1:6 bedding joints to be filled with mortar & Pointing in 1:3 cement mortar job includes raking the joints to 1 cm deep, soaking of bricks prior to use and curing etc complete as per specifications. |
| 20 | BRICK PITCHING: Providing & laying brick pitching with bricks having minimum crushing strength 35 Kg/Cm2 . Bricks shall be laid on flat as per the instruction on 12mm thick cement mortar 1:6 bedding joints to be filled with mortar & Pointing in 1:3 cement mortar job includes raking the joints to 1 cm deep, soaking of bricks prior to use and curing etc complete as per specifications |
| 21 | CEILING PLASTERING 6 MM THK: SMOOTH CEMENT PLASTER FOR CEILING / CHHAJA / ROOF BEAM : Providing and applying 6 mm thick plaster in CM 1:3 to ceiling and bottom surface of chajja using screened sand including finishing smooth and providing drip moulds at chajja edges and curing etc. complete. Rate shall include providing necessary scaffolding, chicken wire mesh at all joints of brick and concrete surfaces, with a minimum overlap of 150 mm in all directions and curing complete. No extra payment shall be made for additional thickness if required to achieve perfect line and level. |
| 22 | PLASTERING 6 MM THK: SMOOTH CEMENT PLASTER : Providing and applying 6 mm thick plaster in CM 1:3 over Masonary / Concretes using screened sand including finishing smooth complete. Rate shall include providing necessary scaffolding, chicken wire mesh at all joints of brick and concrete surfaces, with a minimum overlap of 150 mm in all directions and curing complete. No extra payment shall be made for additional thickness if required to achieve perfect line and level. |
| 23 | SMOOTHPLASTERING-12MM THK: Providing and laying 12mm thick smooth cement plastering in 1:4 CM in single coat to all the interior walls including providing necessary scaffolding, chicken wire mesh at all joints of brick and concrete surfaces with a minimum overlap of 150 mm in all directions and additional thickness if required to achieve perfect line and level, groove cutting without any extra cost. |
| 24 | PLASTERING 20MM THK: Providing and laying average 20 mm thick sand faced cement plaster in Two Coats including providing necessary scaffolding, chicken wire mesh at all joints of brick and concrete surfaces with a minimum overlap of 150 mm in all directions and additional thickness if required to achieve perfect line and level, groove cutting without any extra cost. Apply 12 mm thick coat of CM 1:4 mixed with approved make water proofing compound mixed as per manufacturer's specifications as 1st coat and leaving the surface rough. Apply 2nd coat of 8 mm thick of CM 1:4 and finishing the surface by rubbing with sponge till uniform texture is obtained. |
| 25 | CHAIN LINK FENCING : Supply and fixing of 10 SWG GI chain link fencing (as per Drawing No 123) to the angle iron post with 8 SWG GI hooks and nuts and railing with 14 SWG GI continuous wire (all details shall be as per enclosed drawing ) up to a height of 1.8 m from the ground level. Rate to include unrolling the bundle, erecting, tightening and fixing at 300 mm C-C on the vertical portion of the posts to every top and bottom railing with 14 gauge MS wire. Angle Post / Concrete Poles would be paid separately.(Refer attached Drawing) |
| 26 | CERAMICTILE- 600MMX600MM: CERAMIC TILE FLOORING: Providing and laying matt finish 1st quality Ceramic tiles of 8 mm thick of following size in flooring of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortar of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete. |
| 27 | CERAMICTILE- 450MMX300MM: CERAMIC TILE FLOORING: Providing and laying matt finish 1st quality Ceramic tiles of 8 mm thick of following size in flooring of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortar of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete. |
| 28 | CERAMICTILE- 300MMX300MM: CERAMIC TILE FLOORING: Providing and laying matt finish 1st quality Ceramic tiles of 8 mm thick of following size in flooring of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortar of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete. |
| 29 | CERMICTILEDADO (300MMX 200 MM): CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of 300 x 200 mm size (approved shade and make )First quality , free from crack fissures & flakes with straight edge s & perfect corners fixed at right angles as per the design and pattern, incldg. applying 12mm thick backing plaster in 1:4 CM and fixing the tiles with neatcement paste, finishing the joints with white cement mixed with colouring pigments to match the colour of tiles properly cured & finished in all respects etc. complete. |
| 30 | CERMICTILEDADO (300MMX 400 MM): CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of 300 x 400 mm size (approved shade and make )First quality , free from crack fissures & flakes with straight edge s & perfect corners fixed at right angles as per the design and pattern, incldg. applying 12mm thick backing plaster in 1:4 CM and fixing the tiles with neatcement paste, finishing the joints with white cement mixed with colouring pigments to match the colour of tiles properly cured & finished in all respects etc. complete.300mm x 400mm |
| 31 | CERMICTILEDADO( 300MMX 600 MM): CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of 300 x 600 mm size (approved shade and make )First quality , free from crack fissures & flakes with straight edge s & perfect corners fixed at right angles as per the design and pattern, incldg. applying 12mm thick backing plaster in 1:4 CM and fixing the tiles with neatcement paste, finishing the joints with white cement mixed with colouring pigments to match the colour of tiles properly cured & finished in all respects etc. complete.;300mm x 600mm |
| 32 | WHITE WASH: Providing and applying 3 coats of white wash to plastered and concrete surfaces including providing necessary scaffolding, surface preparation , mixing DDL binder, blue etc. complete as per IS: 712- Latest Edition. If additional coats are required to obtain uniform and smooth finish, the same shall be carried out at no extra cost. |
| 33 | OIL BOUND DISTEMPER : Providing and applying 2 coats ( first coat with brush and final coat with Roller) of OBD of approved make and shade on all surfaces and heights to give an even shade including primimg coat and full putty after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material and labour complete. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable. |
| 34 | White Wash: Providing and applying 3 coats of white wash/colour wash to plastered and concrete surfaces by milk lime providd by HBL with mixing glue etc.complete as directed including alll enabling work and patch work on surface, scaffolding etc.all complete |
| 35 | ACRYLIC EMULSION PAINT (INTERIOR GRADE): Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Acrylic Emulsion paint of approved make and shade on all surfaces and heights to give an even shade including primer and full putty (J K Cement / Birla White) after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material and labour complete. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable. |
| 36 | ACRYLIC EMULSION PAINT (EXTERIOR GRADE) : Providing and applying 3 coats of acrylic anti fungal cement paint including primer of approved make & shade to all the exterior surfaces as per manufacturer's specifications including providing necessary scaffolding, curing , etc. complete. If additional coats are required to obtain uniform finish, the same shall be carried out at no extra,cost as directed by Engineer In Charge. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable. |
| 37 | PLASTIC EMULSION PAINT: Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Plastic Emulsion paint of approved make and shade on all surfaces and heights to give an even shade including primer and compatible putty. Approved Make: Asian/Nitco / Nerolac. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable. |
| 38 | SYNTHETIC ENAMEL PAINT OVER STEEL/WALL/WOOD: Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and of required shades on wall to give an even shade including a primer coat. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable. |
| 39 | SYNTHETIC ENAMEL PAINT OVER STRUCTURAL STEEL:Providing and applying structural steel painting at all heights in Smoke Grey colour, comprising thorough surface preparation by mechanical cleaning/wire brushing to remove rust, dust, oil, and loose scales, followed by one coat of approved metal primer and two coats of approved synthetic enamel/epoxy finish paint in Smoke Grey shade, including all materials, labour, tools, scaffolding, surface preparation, touch-up after erection, and all incidental works complete as per the Engineer-in-Charge's instructions and manufacturer's specifications. |
| 40 | ALUMINIUM PAINT:Providing and applying two coats of approved aluminium paint over one coat of approved metal primer on structural steel surfaces, including surface preparation by wire brushing/cleaning, all materials, labour, tools, scaffolding, and incidental works complete as directed by the Engineer-in-Charge. |
| 41 | POP PUNNING: ON WALL & CEILING: Providing and applying Plaster of Paris(POP) punning on walls, ceilings, beams and columns to bring the surface in plumb line and level including making the surface smooth etc. complete. The rate shall include preparing the surface with POP and compatible putty to give a smooth finish as per approval of the Engg. -In-Charge. Rate to include cost of scrapping, neuro finish etc. complete if needed. |
| 42 | EUROPEAN TYPE W/C ( WALL/FLOOR) :Providing and fixing European type Water Closet (EWC) of vitreous china ceramic, white finish, complete with P-trap or S-trap as specified, dual flush concealed/close-coupled cistern with 3/6 litre flushing capacity, soft-close polypropylene (PP) seat cover and lid, concealed fixing arrangement, all necessary fittings, bolts, connectors, wax seal/rubber gasket, and making all connections complete. The WC shall conform to IS:2556, have a smooth glazed internal surface for easy cleaning, and a minimum ceramic wall thickness of 3 mm. The rate shall include all labour, materials, testing, commissioning, and incidental works complete. Approved makes: Hindware, Parryware, Cera, Jaquar, American Standard, Roca, or equivalent approved. |
| 43 | INDIAN TYPE W/C: Providing and fixing Indian Type Water Closet (Orissa Pan) of vitreous china, white colour, heavy-duty grade with minimum 10 mm wall thickness, anti-skid footrests, P-trap or S-trap as specified, flushing rim for effective cleaning, conforming to IS:771, complete with trap, fixing materials, connection to soil pipe, cement mortar bedding where required, testing and commissioning, including all labour and incidental works. Approved makes: Hindware, Parryware, Cera, Johnson Pedder or equivalent approved. |
| 44 | UPVC PIPE 15 MM DIA 4KG/SQCM: Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable conforming to IS 4985:2000/ IS 15328: 2003/ IS 13592: 1992 Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittings conforming to IS 14735: 1999/ BS 4514/ BS EN 1329, latest edition and other accessories including connections etc., complete as per drawings or as directed at site. Size 15 mm diameter. |
| 45 | UPVC PIPE 25 MM DIA 4KG/SQCM: Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable conforming to IS 4985:2000/ IS 15328: 2003/ IS 13592: 1992 Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittings conforming to IS 14735: 1999/ BS 4514/ BS EN 1329, latest edition and other accessories including connections etc., complete as per drawings or as directed at site. Size 25 mm diameter. |
| 46 | UPVC PIPE 40 MM DIA 4KG/SQCM: Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable conforming to IS 4985:2000/ IS 15328: 2003/ IS 13592: 1992 Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittings conforming to IS 14735: 1999/ BS 4514/ BS EN 1329, latest edition and other accessories including connections etc., complete as per drawings or as directed at site. Size 40 mm diameter. |
| 47 | UPVC PIPE 50 MM DIA 4KG/SQCM: Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable conforming to IS 4985:2000/ IS 15328 : 2003/ IS 13592 : 1992 Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittings conforming to IS 14735 : 1999/ BS 4514/ BS EN 1329, latest edition and other accessories including connections etc., complete as per drawings or as directed at site.50MM |
| 48 | CPVC PIPING (IS 15778)-(1/2'): Providing, laying, jointing, testing and commissioning 15 mm (1/2\\") CPVC pipe conforming to IS:15778, SDR-11 (or as specified), suitable for hot and cold water supply, including all required solvent cement, fittings (couplers, elbows, tees, reducers, unions, etc.), clamps/supports, cutting, threading where required, jointing, testing for leakage, and making good the damaged surfaces complete. Approved makes: Astral, Ashirvad, Supreme, Prince, Finolex, Ajay, or equivalent approved. |
| 49 | CPVC PIPING (IS 15778)-(1'): Providing, laying, jointing, testing and commissioning 25 mm (1\\") CPVC pipe conforming to IS:15778, SDR-11 (or as specified), suitable for hot and cold water supply, including all CPVC fittings (elbows, tees, couplers, reducers, unions, etc.), solvent cement, clamps/supports, cutting, jointing, testing for leakage, and making good complete. Approved makes: Astral, Ashirvad, Supreme, Prince, Finolex, Ajay, or equivalent approved. |
| 50 | 160MMDIA-PVC SWR PIPES: PVC SOIL / WASTE /RAIN WATER PIPE: Supplying and laying the PVC pipe (Astral/Ashirvaad/Supreme/Finolex) conforming to IS 13592:92 including plain or door type bends, shoes, offsets, clamps junctions, tees, etc, complete. Also including cutting, bending & supply and laying of 17 SWG annealed binding wire inside the Pipe for pulling cables in future. |
| 51 | 110 MM DIA- PVC SWR PIPES: PVC SOIL / WASTE /RAIN WATER PIPE: Supplying and laying the PVC pipe(Astral/Ashirvaad/Supreme/Finolex) conforming to IS 13592:92 including plain or door type bends, shoes, offsets, clamps junctions, tees, etc, complete. Also including cutting, bending & supply and laying of 17 SWG annealed binding wire inside the Pipe for pulling cables in future.110 MM DIA PVC PIPE. |
| 52 | 80 MM DIA PVC SWR PIPES: PVC SOIL / WASTE /RAIN WATER PIPE: Supplying and laying the PVC pipe(Astral/Ashirvaad/Supreme/Finolex) conforming to IS 13592:92 including plain or door type bends, shoes, offsets, clamps junctions, tees, etc, complete. Also including cutting, bending & supply and laying of 17 SWG annealed binding wire inside the Pipe for pulling cables in future. size 80mm diameter. |
| 53 | CABLE TRENCH EXCAVATION: Excavation in any type of soil including WBM/asphalt up to 600mm depth and 300mm wide including supply and laying 150mm thick sand on top and bottom of cable, supply and laying bricks laid flat on top, back filling trench etc. complete. (Refer attached Drawing) |
| 54 | RCC PRECAST COVER: Providing, casting, curing, transporting and fixing precast RCC cover slabs of approved size and thickness in M-25 grade reinforced cement concrete with Fe-500 TMT reinforcement, including all materials, centering/shuttering, vibration, curing, lifting hooks, transportation and fixing complete as per approved drawings and specifications.Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. |
| 55 | DISMANTLING RCC : Dismantling of RCC roof, beam, column including carting away debris. |
| 56 | FALSE CEILING: Providing & fixing false ceiling system of Trac 150 F exterior grade or approved equivalent of 0.5mm thick galvanised steel with stove enameled coil coated finish inter locking ceiling panels, carriers, suspension system and edge closure as per the following specification. Supplying and installation of exterior grade 150 F ceiling system comprising of 150 mm x 17 mm deep panels roll formed out of 0.5 mm galvanised steel with stove enameled coil coated finish. The panels shall be pre-treated and coil coated on one side in manufacturers standard colour shades as approved by the Architect/ Engineer in charge. The rear side of the panel shall be given a coat of primer and a wash coat while the finished side shall be given a coat of primer and finish colour coat in polyster paint for a min. dry film thickness of 20 microns, fixed on to the roll formed carriers 34.5 mm x 488 mm deep out of 6 mm thick Galvanised steed with prongs to hold panels in the module of 150 mm at maximum 1.2 mts. C/C. The carriers to be suspended from roof truss by rigid suspension angles as per manufacturer's recommendation. Panels shall be supplied in custom length upto maximum of 5 mts. Job also includes providing ceiling flashing using factory formed 0.5 mm thick Polyster coated galvanised steel material. Rate shall be including providing flashing to cover gap if any between illuminated banding and false ceiling. |
| 57 | PVC False CEILING:Providing and fixing of complete PVC false ceiling system at all levels and heights as per drawings or as directed by the Engineer-in-Charge, including supply and installation of all materials, labour, tools, scaffolding, wastage, and incidental works complete in all respects.The work shall include:Supply and fixing of rigid unplasticized PVC (uPVC) ceiling panels manufactured from 100% virgin PVC compound, thickness 7 mm to 12 mm or as specified in BOQ, hollow/solid type with tongue and groove system, of approved surface finish (plain/embossed/laminated/wood finish), colour and pattern as approved. Panels shall be non-corrosive, termite proof, moisture resistant, washable, fire-retardant, self-extinguishing, and UV stabilized where required.Providing and fixing galvanized iron (GI) suspended framework consisting of perimeter channels, main runners, intermediate channels, and cross members as per approved design, conforming to IS standards with minimum 120 GSM zinc coating (IS 277 or equivalent), including GI threaded rods/hangers, anchor fasteners, and adjustable suspension clamps. The framework shall be properly designed, rigid, leveled, and aligned using laser instruments.Fixing GI perimeter channels to walls with approved fasteners, and suspension system to RCC slab/structural members using approved anchors, including all required supports.Installation of GI grid at spacing not exceeding 600 mm c/c or as per manufacturer’s specifications.Fixing of PVC panels using interlocking tongue and groove system, secured to GI framework with suitable screws/clips ensuring proper alignment, level, and finish without gaps, undulations, or sagging.Making provision for all cutouts/openings for electrical fittings, light fixtures, AC diffusers, smoke detectors, sprinklers, speakers, etc., including edge finishing and reinforcement as required.Finishing, cleaning, removal of protective films, debris, surplus materials, and handing over of ceiling in fully completed and functional condition.Work shall be executed to a tolerance of ±3 mm over 2 m length, ensuring smooth, level, and defect-free surface. |
| 58 | Supply & installation Of Hand Pump: Complete work of providing and installing 1.5\\" dia borewell, including drilling/boring in all types of soil strata, supply and installation of PVC/GI casing and strainer pipes, gravel packing (if required), development and cleaning of borewell, and complete installation of hand pump set (India Mark II or equivalent) with piston, rod, cylinder, spout, handle, fittings, nuts & bolts, including all labour, tools, transportation, testing, and commissioning complete in all respects as per site requirement and direction of engineer-in-charge. |
| 59 | BOREWELL- 6'' DIA: Drilling of perfectly vertical bore hole of a diameter suitable to receive 150 mm nominal dia casing pipe up to desired depth below ground level i/c of the labour charge for transporting lowering and fixing of 150 mm dia meter MS/GI/UPVC casing pipe in side the bore hole i/c all work pertaining to drilling such as transportation installation and removal of drilling machine etc complete. In all type of collapsible strata consisting of soil clay sand moorum gravel boulder, rock etc. |
| 60 | SAND FILLLING:Supply and filling with clean silver / river sand of approved quality in layers of 150 mm each including spreading, compacting by hand ramming and watering etc, all complete as per direction of Engg.-In-Charge. Measurement basis compacted thickness only. |
| 61 | CEMENT PAINT: Providing and applying 2 coats of Water Proof Cement paint of SNOECEM INDIA make and of required shades on all surface and heights to give an even shade as per manufacturer specification and General specifications/guidelines given below: Paint shall be applied strictly as per the manufacturer's recommendation. Paint shall be brought in tin with sealed unbroken and shall be offered for verification to Site-in-charge before use. No thinner shall be used unless approved by Engg-in-Charge. The paint shall be applied by using brush, roller or spraying as directed. The paint etc. shall be applied only after proper surface preparation by removing all dirt, dust, mortar droppings, other foreign matter, loose scale by using brooms, wire brush, sand paper etc as per requirement and direction complete. All holes, cracks, patches etc shall be made good with material similar to that of the surface. The painting shall be applied in specified coats or more so as to obtain the desired finish. If additional coats are required to obtain uniform and smooth finish. The same shall be carried out at no extra cost. The job includes provision of scaffolding using safety precautions, curing etc as required. |
| 62 | Dismantling and Chipping in Old Plaster work |
| 63 | MS Pipe Grouting (1:1.5:3) with Job included Old MS Pipe Cutting & Transportation provided by HBL Plant. |
| 64 | FLAT BACK URINAL: : Supplying and fixing white coloured vitreous china flat back urinal with integrated overflow of Parryware make code C0501 or equivalent approved make |
| 65 | PVC Low-Level Cistern:Providing and fixing approved make 10 litre capacity PVC low-level flushing cistern complete with C.I./PVC brackets, flush pipe, fittings, internal flushing mechanism, float valve, overflow arrangement, connecting pipe, all accessories, including cutting and making good the walls/floor wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 66 | Cistern (Concealed / Wall Hung): Providing and fixing Concealed Dual-Flush Cistern suitable for wall-hung European Water Closet (EWC), comprising heavy-duty ABS concealed cistern with 6/3 L or 4.5/3 L dual-flush mechanism, galvanized powder-coated steel carrier frame/support system, chrome-finish flush actuator plate, inlet and outlet fittings, mounting brackets, connecting pipes, fasteners, and all accessories complete. The rate shall include installation, testing, and commissioning, complete in all respects. Approved makes: Geberit, Grohe, Jaquar, Hindware Artize or equivalent approved. |
| 67 | WASH BASIN(WALL HUNG):Providing and fixing Wash Basin of vitreous china/ceramic, white colour, approximate size 520 × 420 mm, with single or double tap hole as specified, integral overflow provision, chrome-plated pop-up waste coupling, complete with fixing brackets, screws, bolts, PVC waste pipe connection, and all necessary accessories. The basin shall conform to IS:2556 (Part 5). The rate shall include all labour, materials, testing, and commissioning complete. Approved makes: Hindware, Parryware, Cera, Jaquar, Roca, TOTO or equivalent approved. |
| 68 | BIB COCK (SHORT BODY):Providing and fixing 15 mm dia chrome plated brass bib cock, short body type, of approved make(Jaquar / Cera / Hindware), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, and washers, including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 69 | ANGLE COCK:Supplying and fixing brass angle cock (stop cock) of approved make (Jaquar / Cera / Hindware / Parryware), conforming to relevant IS specifications, complete with all fittings and accessories such as PTFE tape, wall flange, nipples, washers, testing, commissioning, and making good the surface wherever required, as directed by the Engineer-in-Charge. |
| 70 | BIB COCK (LONG BODY):Providing and fixing 15 mm dia chrome plated brass bib cock, long body type, of approved make(Jaquar / Cera / Hindware), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, and washers, including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 71 | BIB COCK (TWO WAY):Providing and fixing 15 mm dia chrome plated brass bib cock, two way type, of approved make(Jaquar / Cera / Hindware), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, and washers, including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 72 | ANGLE COCK(TWO WAY):Supplying and fixing Brass two-way angle cock (diverter type stop cock) of approved make(Jaquar/Cera/Hindware), conforming to relevant IS specifications, complete with all fittings and accessories such as PTFE tape, wall flange, nipples, washers, testing, commissioning, and making good the surface wherever required, as directed by the Engineer-in-Charge. |
| 73 | HAND SHOWER:Providing and fixing chrome plated brass health faucet (hand shower) of approved make(Jaquar / Cera / Hindware), complete with 15 mm dia angle cock, flexible PVC/SS braided hose pipe, wall hook/holder and all necessary fittings and accessories, including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 74 | WALL MIXER:Providing and fixing wall mounted mixer of approved make(Jaquar / Cera / Hindware), 15 mm dia, chrome plated brass, suitable for mixing hot and cold water supply, complete with all necessary fittings, wall flanges, connectors, and accessories, including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 75 | BASIN TAP:Providing and fixing 15 mm dia chrome plated brass basin tap (pillar cock type), of approved make(Jaquar / Cera / Hindware), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, washers, and connection to existing pipe line, including testing, commissioning, and making good the works wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 76 | BIB COCK (SHORT BODY):Providing and fixing 15 mm dia PVC bib cock, short body type, of approved make (Watertec / Finolex / Astral / Ashirvad or equivalent), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, washers, etc., including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 77 | BIB COCK (LONG BODY):Providing and fixing 15 mm dia PVC bib cock, long body type, of approved make (Watertec / Finolex / Astral / Ashirvad or equivalent), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, washers, etc., including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 78 | BIB COCK (TWO WAY):Providing and fixing 15 mm dia PVC bib cock, two way type, of approved make (Watertec / Finolex / Astral / Ashirvad or equivalent), conforming to relevant IS specifications, complete with all necessary fittings and accessories such as PTFE tape, nipples, washers, etc., including testing, commissioning, and making good the walls wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 79 | HAND SHOWER:Providing and fixing 15 mm dia PVC hand shower of approved make (Watertec / Finolex / Astral / Ashirvad or equivalent), conforming to relevant IS specifications, including all fittings and accessories such as PTFE tape, nipples, washers, etc., complete with testing, commissioning, and making good the wall wherever required, as directed by the Engineer-in-Charge. |
| 80 | WALL MIXER:Supplying and fixing plastic wall mixer for hot and cold water (2-inlet/3-inlet as required) of approved make(Watertec / Finolex / Astral / Ashirvad or equivalent), conforming to relevant IS specifications, complete with all fittings and accessories such as wall flanges, PTFE tape, nipples, washers, testing, commissioning, and making good the wall wherever required, as directed by the Engineer-in-Charge. |
| 81 | BASIN TAP:Supplying and fixing PVC basin tap (bib cock / pillar cock as required) of approved make, conforming to relevant IS specifications, complete with all fittings and accessories such as PTFE tape, nipples, washers, escutcheon plate, testing, commissioning, and making good the surface wherever required, as directed by the Engineer-in-Charge. |
| 82 | ANGLE COCK:Supply and fixing of 15 mm (½\\") heavy-duty PVC plastic bib cock of approved make(Watertec / Finolex / Astral / Ashirvad or equivalent), complete with all necessary fittings, PTFE tape, and accessories, including making watertight connections, testing, and commissioning, complete as directed by the Engineer-in-Charge. |
| 83 | ANGLE COCK(TWO WAY):Supply and fixing of 15 mm (½\\") 2-way angle cock of approved make(Watertec / Finolex / Astral / Ashirvad or equivalent), complete with wall flange, PTFE tape, and all necessary fittings and accessories, including making leak-proof connections, testing, and commissioning, complete as directed by the Engineer-in-Charge. |
| 84 | CONNECTION PIPE:Supplying and fixing of 15 mm (½\\") PVC braided flexible connection pipe of approved quality and make, suitable for hot and cold water supply, complete with brass nuts/ferrules at both ends, including making leak-proof joints, testing and commissioning, complete as directed by the Engineer-in-Charge. |
| 85 | Valve(1/2\\"):Supplying and fixing of 15 mm (½\\") PVC/Upvc full way valve / stop valve / gate valve of approved make, complete with necessary fittings, PTFE tape, and accessories, including testing and commissioning of leak-proof joints, complete as directed by Engineer-in-Charge. |
| 86 | Valve/NRV(1\\"):Supplying and fixing of 25 mm (1\\") PVC/Upvc full way valve / NRV / stop valve / gate valve of approved make, complete with necessary fittings, PTFE tape, and accessories, including making leak-proof joints, testing and commissioning, complete as directed by Engineer-in-Charge. |
| 87 | Valve(1/2\\"):Supplying and fixing of 15 mm (½\\") brass full way valve / stop valve / gate valve of approved make, complete with necessary fittings, PTFE tape, and accessories, including testing and commissioning of leak-proof joints, complete as directed by Engineer-in-Charge. |
| 88 | Valve(1\\"):Supplying and fixing of 25 mm (1\\") brass full way valve / stop valve / gate valve of approved make, complete with necessary fittings, PTFE tape, and accessories, including making leak-proof joints, testing and commissioning, complete as directed by Engineer-in-Charge. |
| 89 | CARPENTOR:Providing services of a skilled carpenter on a per-day basis for carrying out carpentry works including repair, fabrication, installation, fixing, dismantling, maintenance, and other allied carpentry works as directed by the Engineer-in-Charge. The rate shall include the cost of all hand tools, minor consumables, transportation, and incidental expenses required for satisfactory completion of the work. |
| 90 | PLUMBER:Providing services of one skilled plumber along with one helper on a per-day basis for carrying out plumbing works including installation, repair, maintenance, dismantling, leak rectification, replacement of sanitary and water supply fittings, pipe laying/jointing, testing, and other allied plumbing works as directed by the Engineer-in-Charge. The rate shall include the cost of all hand tools, minor consumables, transportation, and incidental charges required for execution of the work. |
| 91 | ART PAINTER:Providing services of one skilled Art Painter on a per day basis for execution of artistic painting works including writing of slogans, logos, murals, lettering, graphics, and decorative artwork, with all necessary tools, brushes, consumables, and incidental charges, complete as directed by the Engineer-in-Charge. |
| 92 | PROVIDING AND APPLYING WATER PROOFING: Providing and Apply Waterproofing: carrying out water proofing works wherever required as Per the Waterproofing Standards. Integral Cement Waterproofing Compound Confirming to IS 2645 and of approved make and manufacture enlisted by the site in-charge from time to time shall be used. The contractor shall bring the materials to the site in their original packing. The containers will be opened and the material mixed with dry cement in the proportion by weight,recommended by the manufacturers or as specifically described in the description of the item. care shall be taken in mixing, to see that the water proofing material gets well and integrally mixed with the cement and does not run out separately when water is added. Rate to include Additional 50mm PCC layer in 1:1.5:3 mix which is to be done to maintain the slop. |
| 93 | GLASS 8 MM: Supply and fixing 8mm plain glass including necessary beadings, putty, hardware etc. Rate to include removal old broken glass panels of doors, windows etc. |
| 94 | GLASS 6 MM: Supply and fixing 6mm plain glass including necessary beadings, putty, hardware etc. Rate to include removal old broken glass panels of doors, windows etc. |
| 95 | ALUMINIUM DOOR/WINDOW:PROVIDING & FIXING POWDER COATED (50 MICRON THICKNESS) ALUMINIUM DOOR/WINDOW/PARTITION WITH THE DOOR FRAME, DASH FASTNERS, LOCK, DOOR CLOSURE, TOWER BOLT, HINGES, HANDLE, STOPPER, RUBBER, PVC BEADING, GLAZING CLIP ETC COMPLETE IN ALL RESPECTS. (EXCLUDING CHOWKHAT). SECTION FRAME SIZE -100x40 (minimum 16 gauge or thicker as per requirement), TOP & BOTTOM HORIZONTAL MEMBERS OF DOORS ARE TO BE OF SIZE 100x40 MM (minimum 18 gauge or thicker as per requirement) LONG STANDING MEMBERS & HORIZONTAL BELT MEMBER ARE TO BE OF SIZE45X45 MM (minimum 18 gauge or thicker as per requirement). RATE TO INCLUDE MATERIAL, TRANSPORTATION, LABOUR, ACCESORIES, TOOLS & TACKLES ETC COMPLETE IN ALL RESPECTS. Item to include 5 mm thick float glass & particle board of approved make 12mm thick or ACP Panel board of approved brand and specifications. |
| 96 | Ply door :Providing and fixing factory made ISI marked flush door shutters conforming to IS:2202 (Part-I) solid core type, non-decorative (or decorative as specified), consisting of 1st class hard wood stiles and rails, core of block board construction, and commercial 3 ply BWR grade plywood face panels on both sides, including all necessary teak wood lipping on all edges, ISI marked stainless steel butt hinges with screws, fixing in position in existing chowkhat/frame, complete in all respects as per drawings and direction of Engineer-in-Charge. |
| 97 | WPC door :Providing and fixing factory-manufactured solid core Wood Plastic Composite (WPC) door shutter of approved make, size and thickness (25mm/30 mm/32 mm as specified), manufactured from high-density WPC material, waterproof, termite proof, borer proof, fungus resistant, and fire-retardant, with smooth finished surface suitable for painting or polishing as required, including providing and fixing ISI-marked stainless steel butt hinges (minimum 3 Nos. per shutter), stainless steel screws, approved quality handles, tower bolts, stoppers and other necessary hardware fittings, fixing to existing door frame or WPC door frame complete with proper alignment, adjustments, testing for smooth operation, and all labour, tools, tackles, consumables and incidental works, complete in accordance with approved drawings, relevant IS standards/manufacturer's specifications, and as directed by the Engineer-in-Charge. |
| 98 | WATER TANK 1000 LTRS. : Supplying and installation of 1000 litre capacity HDPE water storage tank of Sintex make or approved equivalent brand, conforming to relevant IS standards for rotational moulded polyethylene water storage tanks, including placing at designated location as per approved drawings. The work shall include making all necessary GI pipe connections for inlet, outlet, and overflow lines with required fittings such as sockets, unions, elbows, valves, clamps, and jointing materials, ensuring leak-proof connections. The scope also includes thorough cleaning, flushing, and disinfection of the tank before commissioning, testing for proper functioning, and handing over complete in all respects as per direction of Engineer-in-Charge. |
| 99 | Kerb stone:Providing, supplying and laying precast cement concrete kerb stones of M25 grade, size 300 mm × 150 mm × 1000 mm (Depth × Width × Length), at or near ground level, laid to the required line, level, grade and curvature on a prepared base, jointed with cement mortar 1:3 (1 cement : 3 coarse sand) with joints not exceeding 5 mm in width (except at approved sharp curves), including finishing of joints with or without grooves, providing drainage openings wherever required, curing, handling, loading, unloading, transportation, and all labour, tools, tackles and incidental works complete as per approved drawings, relevant IRC/MoRTH specifications and as directed by the Engineer-in-Charge. |
| 100 | DIS. OF BRICK MASONARY:Dismantling of brick masonry/PCC /RR masonry including carting away debris. |
| 101 | DOOR CLOSER:Providing and fixing Heavy duty door closer. of approved make size no. 2. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender