Tender For Construction Work Of A Total Of 26 Duplex Buildings On Plot No. C-1 To C-26 (Plot Size-7.50 X15.00M) In Sector-8 Of Greater Bareilly Residential Scheme.
Tender Value
10.49 Crore
Estimated cost
Bid Submission
08 Oct 2026
23 days left
EMD
20.99 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bareilly → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Work Of A Total Of 26 Duplex Buildings On Plot No. C-1 To C-26 (Plot Size-7.50 X15.00M) In Sector-8 Of Greater Bareilly Residential Scheme.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.D.S.R. Item No. 2.8.1 |
| 2 | Earth Filling including cartageEarth work cutting on in embankment in ordinary soil earth work in embankment to be in 20cm layers including watering dressing and compacting the soil to achieve 95% proctor density and also including the surface required level and slops and also including lift 1.50m and lead 8km.D.S.R. No. 1.1.2 |
| 3 | Providing & laying cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.8 |
| 4 | C.C. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.3 |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriagefor all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 350 kg /cum All works upto plinth level RCC as in fdns and footings of colums and plinth beam and bases of column. DSR Item No. 5.33.1.1 |
| 6 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum (level 1 to lvl-5) D.S.R. Item No. 5.33.2.1 |
| 7 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominalsize derived from natural sources)..DSR Item No. 4.2.2 |
| 8 | Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an overall rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage and over lapping and hooks and authorised overlapping shall be measured . D.S.R. Item No. 5.22.1 |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for footings/PB, rough finished surface of conc. D.S.R. Item No. 5.9.1 |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for columns, pillers, piesr, abutment , post and strutsD.S.R. Item No. 5.9.6 |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantileversD.S.R. Item No. 5.9.5 |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roof , landings, balconies, acessess platformD.S.R. Item No. 5.9.3 |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.D.S.R. Item No. 5.9.2 |
| 14 | Brick work in foundation 1st class b/work in 1:4cement and couarse sand mortar in fdn and plinth incl. supply of all materials , labour and t& P required for proper completion of the workD.S.R. Item No. 6.2.1 |
| 15 | Brick work in SUPER STRUCTURE in 23 cm thk wall with 1:4 cement and coarse sand incl. all materials labour annd t&p etc. for proper completion of work.D.S.R. Item No. 6.4.1 |
| 16 | Class 150 Brick work in 1:3 cement and Coarse Sand of 1.25 finentss modulusbut in Parapet including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cms.D.S.R. Item No. 6.13.1 |
| 17 | 12 mm thk plaster (1:4) with cement & Coarse Sand (Fair Face)D.S.R. Item No. 13.4.1 |
| 18 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)D.S.R. 13.5.1 |
| 19 | Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80 |
| 20 | Finishing walls with Acrylic Smooth exterior paint of required shade :-New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10sqm.).D.S.R. Item No. 13.46.1 |
| 21 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.D.S.R. Item No. 13.45.1 |
| 22 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @0.75 ltr /10 sqmD.S.R. Item No. 13.48.1 |
| 23 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.1 Second class teak woodD.S.R. Item No. 9.1.1 |
| 24 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screwsD.S.R. Item No. 9.21.1 |
| 25 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)On one side onlyD.S.R. Item No. 9.22.1 |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new workD.S.R. 13.62.1 |
| 27 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete asper approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. D.S.R. Item No. 9.147.A1.1 Make : Fanesta(ii) Sites with structure height more than 20m for all wind speeds9.147.A1 Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (40 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre). |
| 28 | 6 mm thick clear heat strengthened glass(Make : as provided by Fenesta)DSR 2618 |
| 29 | Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: 20 mm Dia D.S.R. 1.21.1 (Rate: 128.00x0.755x0.97)=93.74 |
| 30 | Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: 25 mm DiaD.S.R. 1.21.2 (Rate: 145.00x0.755x0.97)=106.19 |
| 31 | Providing and fixing of junction box 200 x 250 mmPWD SI No 154 elctrical SOR 2018 |
| 32 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm(Make : Simpolo/Johnson)DSR 11.41A.1.3 |
| 33 | Antiskid tilesProviding and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size600 x 600 mm (Make : Simpolo/Johnson)DSR 11.41A.3.1 |
| 34 | Extra for grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm D.S.R. Item No. 11.48.2 |
| 35 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Make : Simpolo/Johnson)DSR 8.31 |
| 36 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.D.S.R. Item No. 11.55.1 |
| 37 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. D.S.R. Item No . 8.5 |
| 38 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite workD.S.R. Item No. 8.3.2 |
| 39 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 9.76 |
| 40 | Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 9.77 |
| 41 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: DSR 22.7.1(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofingcompound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 andapproved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.D.S.R. 22.7.1 |
| 42 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarsesand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase D.S.R 2021No 12.21.1 |
| 43 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. D.S.R. No.12.22.1 |
| 44 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finishof tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board Ground FloorD.S.R. ITEM No. 12.45.3 |
| 45 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).D.S.R. Item No. 10.28 |
| 46 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksD.S.R. Item No. 10.25.2 |
| 47 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white plastic seat and lidMake: JaquarD.S.R. Item No. 17.2.1 |
| 48 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap.Make: JaquarD.S.R. Item No. 17.7.4 |
| 49 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe : 32mm diaMake : Finolex/AstralD.S.R. Item No. 17.28.1 |
| 50 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. D.S.R. Item No. 17.31.1 |
| 51 | Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm nominal boreMake : JaquarD.S.R. Item No. 17.16A |
| 52 | Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms.Make: JaquarD.S.R. Item No. 17.71 |
| 53 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.110mm diameterMake : Finolex/AstralD.S.R. Item No. 12.41.2 |
| 54 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm Make : Finolex/AstralD.S.R. Item No. 12.43.2 |
| 55 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.Make : Finolex/AstralD.S.R. Item No. 12.44 |
| 56 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20mm dia nominal outer dia pipesMake : Finolex/AstralD.S.R. Item No. 18.7.2 |
| 57 | 25mm dia nominal outer dia pipesD.S.R. Item No. 18.7.3 |
| 58 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15mm dia nominal outer dia pipesMake : Finolex/AstralD.S.R. Item No. 18.8.1 |
| 59 | 20mm dia nominal outer dia pipesD.S.R. Item No. 18.8.2 |
| 60 | 25mm dia nominal outer dia pipesD.S.R. Item No. 18.8.3 |
| 61 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions15mm nominal bore.D.S.R. Item No.18.21.2.1 |
| 62 | Providing & fixing CP brass bib cock of approved quality conforming to IS 893115mm nominal boreMake : JaquarD.S.R. Item No. 18.49.1 |
| 63 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal boreMake : JaquarD.S.R. Item No. 18.53.1 |
| 64 | Providing and fixing gun metal gate valve with wheel of approved quality.25mm dia nominal boreMake : JaquarD.S.R. Item No. 18.17.1 |
| 65 | Providing and fixing gun metal gate valve with wheel of approved quality.20mm dia nominal boreMake : JaquarD.S.R. Item No. 18.17.1A |
| 66 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore Make : Jaquar D.S.R. Item No. 18.18.3 |
| 67 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Make : Finolex/AstralD.S.R. Item No. 18.48 |
| 68 | Providing & laying PVC Pipe 100mm diameterMake : Finolex/AstralPWD SOR 730A |
| 69 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern.Make : JaquarD.S.R. 17.5.4 |
| 70 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board510x1040 mm bowl depth 250 mmD.S.R. Item No. 17.10.1.1 |
| 71 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C Make: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.10.3 Electrical 2025 |
| 72 | Wiring for circuit/sub-main wiring along with earth wire with the following size of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-Charge 2X1.5 sqmm +1x1.5 sqmm earth wire D.S.R. Item No. 1.14.1 Electrical 2025 |
| 73 | 2X2.5 sqmm + 1x 2.5 sqmm earth wireMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.14.2 Electrical 2025 |
| 74 | 2X4.0 sqmm + 1x 4.0 sqmm earth wireMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.14.3 Electrical 2025 |
| 75 | 2X6.0 sqmm + 1x 6.0 sqmm earth wireMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.14.4 Electrical 2025 |
| 76 | Supplying and drawing co-axial TV cable RG-6 graded, 0.7 mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. Make: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.19 Electrical 2025 |
| 77 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. TV antenna socket outletMake: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.24.7 Electrical 2025 |
| 78 | Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. Make: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-Charge D.S.R. Item No. 1.25 Electrical 2025 |
| 79 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.Make: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.26 Electrical 2025 |
| 80 | Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module(75mm X 75 mm )D.S.R. Item No. 1.27.1 Electrical 2025 |
| 81 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connection etc. as required.D.S.R. Item No. 1.31 Electrical 2025 |
| 82 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,connection etc. as required. D.S.R. Item No. 1.32 Electrical 2025 |
| 83 | Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/woodedn block including connectionetc. as required. D.S.R. Item No. 1.33 Electrical 2025 |
| 84 | Supplying and fixing brass batten/angle holder including connectionetc. as required.D.S.R. Item No. 1.34 Electrical 2025 |
| 85 | Instalation,testing & commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLSCFL/LED lamps per fitting, complete with all accessories including connection etc. as required.D.S.R. Item No. 1.35 Electrical 2025 |
| 86 | Installation, testing and commissioning of prewired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. PVC insulated, copper conductor, single core cable etc. as required. D.S.R. Item No. 1.41 Electrical 2025 |
| 87 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. Including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.D.S.R. Item No. 1.45 Electrical 2025 |
| 88 | Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.D.S.R. Item No. 1.49 Electrical 2025 |
| 89 | Installation of exhaust fan in the existing opening, including making good the damage, connections, testing, commissioning etc. as required. upto 450 mm sweep.D.S.R. Item No. 1.50.1 Electrical 2025 |
| 90 | Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. D.S.R. Item No. 1.51 Electrical 2025 |
| 91 | Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, `C` curve including connections, painting etc. as required.D.S.R. Item No. 1.57 Electrical 2025 |
| 92 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Disect Current(BLDC) motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value(CM/M/W) minimum 6, Air delivery minimum 210 Cum/Min, 350 RPM(tolerance as per IS: 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise= 75 degree C(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.Make: Schneider / Crompton / Bajaj / or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 9.2.3 Electrical 2025 |
| 93 | Supplying and fixing following way, single pole and neutral sheet steel, MCB distribution board, 240 V on surface /recess complete with , tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge 12 way, Double doorD.S.R. Item No. 2.3.3 Electrical 2025 |
| 94 | Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge Single PoleD.S.R. Item No. 2.10.1 Electrical 2025 |
| 95 | Double Pole Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge Single PoleD.S.R. Item No. 2.10.3 Electrical 2025 |
| 96 | 6 Way TPN Make: Schneider/MDS Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge Single Pole D.S.R. Item No. 2.24.2 Electrical 2025 |
| 97 | Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required.Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-ChargeSingle PoleD.S.R. Item No. 2.11 Electrical 2025 |
| 98 | Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required. Make: As approved in U.P.P.W.D & C.P.R.I.D.S.R. Item No. 5.4 Electrical 2025 |
| 99 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) D.S.R. Item No. 5.9 Electrical 2025 |
| 100 | Supplying and Laying of 6 SWG G.I wire at 0.50 metre below ground level for conductor earth electrode, including connection / terminating with G.I. thimble etc. as required.Make: As approved in U.P.P.W.D & C.P.R.I.D.S.R. Item No. 5.7 Electrical 2025 |
| 101 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mmMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.10.7.1 Electrical 2025 |
| 102 | Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operatingvoltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -50C to 400C, internal surgeprotection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver &electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained tilllife ends, CCT 3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc.as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Wattoutput . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall besubmitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trimBGSLO Sleek Recess RD 9W WH LEDMake: Bajaj / Jaquar / Go Green or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.8.1.2 Electrical 2025 |
| 103 | LED Batten light (System lumen efficacy >135lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard DeviationColor Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm) 18- 22 WattMake: Bajaj / Jaquar / Go Green or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.8.11.1 Electrical 2025 |
| 104 | S/f of 340 mm wide x 101.6 mm deep(3.0\\") Concealed Box PWD SOR Item No. 1151c |
| 105 | Supply of 300mm dia sweep PVC body, 900±10% RPM Exhaust fan with guard and mounting arrangement.300mm sweep. Make: Bajaj / Usha/Atomberg |
| 106 | Providing, supplying, installing, testing and commissioning recessed LED downlight (12W, warm white, 3000K, die-cast aluminium body, IP20, BIS approved, Philips/Schneider/Wipro/Crompton or equivalent), complete with driver and all accessories.Make: Bajaj / Jaquar / Go Green |
| 107 | Providing, supplying and fixing 7/9 Watt LED Bulb, suitable for 230 V, 50 Hz AC supply, with required holder/base and all necessary accessories, including removal/replacement of existing bulb wherever required, connection, testing and commissioning, complete in all respects as per specifications and direction of Engineer-in-Charge.Make: Bajaj / Jaquar / Go Green |
| 108 | Providing and fixing recessed COB LED spotlight (7W–12W, adjustable beam, warm white) for feature walls and decorative panels, complete.Make: Bajaj / Jaquar / Go Green Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 23 daysOct 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender