Tender For Maintanance Works Arrangements For Amma Unavagam Building @ Thirupparankundram Bus Stand In Ward No-99.
Tender Value
4.64 Lakhs
Estimated cost
Bid Submission
28 Sep 2026
12 days left
EMD
4647
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Madurai → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Maintanance Works Arrangements For Amma Unavagam Building @ Thirupparankundram Bus Stand In Ward No-99.
BOQ
| Sl. No. | Item Description |
| 1 | Picking the existing cement plaster sutface. SOR-2024-25-P-- |
| 2 | Cleaning the Tiles Or Cut stones using mild hydrofloric acid and powder and water pressure |
| 3 | Plastering with cement mortar (1:5) 20mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications. |
| 4 | Paving the floor with Vitrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work. |
| 5 | Fabrication supply and fixing of fully paneled double leaf steel door made of 40x40x6mm MS angle for outer frame and shutter made out of 35x35x6mm MS angle with necessary stiffness 32x6mm and flats at 30cm interval and necessary cross diagonal MS flats. The shutter frame should be fully covered by 18G GR sheet and provided with required locking arrangements and one coat of red oxide paint and primer etc… |
| 6 | Supplying and Fixing of Stainless Steel Sink Size:600mm x 450mm x 200mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc. |
| 7 | Painting old wall surface with Two coat of Plastic Emulsion paint of approved quality including cleaning of plaster surface with soap soda and water by manual labour. |
| 8 | Painting two coats with Ready Mixed Enamel Paint over the Old iron works of approved quality and colour with out priming coat including the cost all materials etc., complete, in all floors. |
| 9 | Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. |
| 10 | Wiring with 2x1.5sq.mm. PVC insulated unsheathed FRLS SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch in flush with wall covered with hylem sheet of 3mm thick with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (SD 21) |
| 11 | Supply and Fixing of 48W LED Street Light Fitting with LED (LIGHT EMITTING DIODE) Higher End Philips / Havells / Equivalent |
| 12 | Supplying and fixing of 18W 4 Feet LED Fitting with LED |
| 13 | Supplying and fixing of 48” AC ceiling fan with 300mm down rod on the existing clamp with regulator with complete set |
| 14 | Supply of Gas Stove Three Burner Heavy Type. |
| 15 | Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum- Purifier to deliver Potable Water with World HealthOrganisation (WHO) Standards with following accessories.(a) MS Skid - 1 No.(b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set(c) Feed Pump 0.50 HP – 1 No.(d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings.The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. 50Lit Capacity |
| 16 | Construction of Inspection Chambers of following sizes with earth work for foundation with 25cm thick brick jelly cement concrete bed in C.M 1:4:10 using 40mm brick jelly for foundation brick work in C.M 1:6 for chambers, plastering with C.M 1:3 12mm thick benching, channelling, 75mm thick RCC loose slab covering in CM 1:2:4 mix using 20mm blue granite jelly including necessary reinforcement etc complete 60x60x60cm |
| 17 | Supply of , PVC pipes and Specials32mm CPVC Pipe |
| 18 | 25mm CPVC Pipe |
| 19 | 20mm CPVC Pipe |
| 20 | 32mm CPVC Coupler |
| 21 | 25mm CPVC Coupler |
| 22 | 20mm CPVC Coupler |
| 23 | 32mm CPVC Elbow |
| 24 | 25mm CPVC Elbow |
| 25 | 20mm CPVC Elbow |
| 26 | 32mm CPVC Tee |
| 27 | 25mm CPVC Tee |
| 28 | 20mm CPVC Tee |
| 29 | CP Screw Down Taps |
| 30 | 110 mm PVC (6 KSC) |
| 31 | 160mm PVC (6 KSC) |
| 32 | 110mm Elbow |
| 33 | 160mm Couplers |
| 34 | Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI Consider Alu. Partition Size 6.3m x2.4m Consider Alu. Section 2x38x2mm @ 1.174kg / m PLB exterior Grade 12 mm thick Glaass for partion 4 mm thick. |
| 35 | Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections. |
| 36 | Add GST 18% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender