Tender For Hot Mixing Of Balance Roads In Phase 1A, I, Ii, Iii, Iv At Verna Industrial Estate.
Tender Value
4.55 Crore
Estimated cost
Bid Submission
18 Sep 2026
3 days left
EMD
9.11 Lakhs
Bank guarantee accepted
Document Fee
15000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Hot Mixing Of Balance Roads In Phase 1A, I, Ii, Iii, Iv At Verna Industrial Estate.
BOQ
| Sl. No. | Item Description |
| 1 | Supplying of laterite stone soling of size 150-200 mm size and murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power road roller including spreading, watering and consolidation of binding material etc.(Measurements shall be considered on finished item) . |
| 2 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3-wheeled steel/vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density.as per MORTH Specification 404By Manual MeansGrade - II |
| 3 | Providing and laying 50mm(consolidated thickness)full grout using granitic or basaltic stone of specified grading at 6.00 cu.m. per 100 sq.m. grouting with hot bitumen straight run bitumen(or with such bituminous material of grade and type as specified by the Engineer-in-Charge)at 5.0kg. per sq. m. binding with key aggregate of granitic or basaltic stone of specified grading at 1.5 cu.m. per 100 sq.m. including Providing and laying seal coat sealing the voids in a bituminious surface laid with F.E loader with 1 Cu.m. bucket capacity to the specified levels, grade and cross fall using Type A seal coat with 0.98 kg/sqm ofbitumen of grade as per MoRT&H specifications clause 513. |
| 4 | Cleaning of the existing black topped surface with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. etc. complete |
| 5 | Providing and applying tack coat with bitumen grade of 80/100 or bitumen emulsion using pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom as per MoRT&H specifications clause 503.Bitumen 80/100@ 0.375 kg/sq.m |
| 6 | Providing and laying dense graded bituminious macadam with 40-60 TPH Drum Mix type HMP producing an average output of 50 tonne per hour using crushed aggregates of specified grading, premixed with bituminious binder by specified percentage of weight of total mix and filler, transporting the hotmix to work site, with all leads laying with a hydrostatic /hydraulic paver finisher with sensor to control the required grade, level and alignment, rolling with smooth wheeled, vibratory or tandem rollers to achieve the desired compaction using antistripping agent complete as per MoRT&H Specifications Clause 507Grade-II (19mm nominal size) Bitumen @ 5% of weight of mixAntistripping agent @ 0.5% of bitumen content |
| 7 | Providing and laying 30 mm thick Bituminious/Asphaltic concrete with 40-60 batch type HMP producing an average output of 50 tonnes per hour using crushed aggregates of specified gradings Premixed with bituminious binder at 6.5 % by weight of total mix and fillerusing Antistripping agent transpoting the hotmix to work site with all leads and applying a tack coat @f 2.00 kg/10sq.m. with hot bitumen of 80/100 and laying with Mechanical Paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory or tandem rollers to achieve the desiredcompaction as per MORT&H specifications clause 509 and 503 Antistripping agent @ 0.5% of bitumen content |
| 8 | Raising side shoulders with hard murrum including spreading watering and consolidationMurrum from borow puit |
| 9 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC :35. The finished surface to be level uniform and freefrom streaks and holes as per MORTH Specification 803 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysSep 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender