Tender For special Repair To Avoid Leakage And Seepage Of Jcos/Or Single Living Accn Of Bldg No. P-216, P-217, P-220, P-238, P-240, P-241, P-242, P-205, P-206, Lgo-27 And Lgo-28 Of 17 Jat At Shillong Cantt And Provn Of Overhead Covered Pathway And Pr
Tender Value
45.51 Lakhs
Estimated cost
Bid Submission
08 Oct 2026
3 days left
EMD
91020
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Khasi Hills → Meghalaya
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Avoid Leakage And Seepage Of Jcos/Or Single Living Accn Of Bldg No. P-216, P-217, P-220, P-238, P-240, P-241, P-242, P-205, P-206, Lgo-27 And Lgo-28 Of 17 Jat At Shillong Cantt And Provn Of Overhead Covered Pathway And Provn Of Retaining Wall With Interlocking Tiles And Shed Infront Single Jcos Accn Of 101 Area Sig Coy And Provn Of Operator Room In Conf Halll Under Ge Shillong
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 22-Sep-2026 | BOQ CORRIGENDUM | BOQ | 01-Oct-2026 |
| 2 | 01-Oct-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 08-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed. |
| 2 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc, n exc 10 sqm on plan and and getting out in soft/loose soil complete all as specified and dorected. |
| 3 | Returning, filling in including spreading levelling, watering and well ramming in layers n.exc 25cm thick in soils complete all as specified and directed. |
| 4 | Removing excavated material to a distance n. exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 5 | M&L for PCC 1:4:8 Mix, type D-2 (using 40mm graded crushed stone aggregate) as in foundations, fillings and mass concrete complete all as specified and directed. |
| 6 | Taking down chowkat or frame area exc 1.5 Sqm but n.exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed. |
| 7 | Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles, all as specified. |
| 8 | Dismantling unframed wooden work as in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed. |
| 9 | Dismantling wall and ceilling boards of any description including cover fillets complete all as specified and directed. |
| 10 | Dismantling boarding any description fixed in any position with nails complete all as specified and directed. |
| 11 | Cutting openings of old masonry walls built in cement mortar through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for under pinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and directed. |
| 12 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre using Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified to recieve 12mm thick calcium silicate board complete all as specified and as directed . |
| 13 | M&L for Seamless 12mm thick calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of faceboard with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) incl any sunk or raised shape or design complete all as specified and directed. |
| 14 | S&F Gl frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mmm c/c using GI wire of 4mm thickness GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and directed . |
| 15 | S&F 4mm thick E Board 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and directed. |
| 16 | S&F 2nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 13 and n.exc. 25 sqcm complete all as specified and directed. |
| 17 | S&F 2nd class SW boarding 20mm thick fixed with nails in eaves board plained one side with butt joint complete all as specified and directed. |
| 18 | M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid ,rounded or chamfered, put together with glue pinned at joints , supplied and fixed complete all as specified and directed. |
| 19 | S&F 35mm thick premium teakwood ornamental designer door shutters of solid core construction of design and colour as approved by GE incl french polishing as approved complete all as specified and directed. |
| 20 | S&F 18/19 mm thick block boards, grade I quality, exterior grade, commercial type, fixed with screwed to tmber frame work fixed with screws to timber frame complete all as specified and directed. |
| 21 | S&F 12 mm thick block boards, grade I quality, exterior grade, commercial type, fixed with screwed to tmber frame work fixed with screws to timber frame complete all as specified and directed. |
| 22 | S&F 1.5 mm thick decorative laminates type 1 of surface finish color and pattern as approved fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. |
| 23 | Providing and fixing PVC edge lipping, of approved make, colour, shade and thickness, to the exposed edges of kitchen cabinet shutters, drawers, shelves and other cabinet components, using approved adhesive, including cutting, fitting, pressing, trimming, rounding/chamfering of edges and making the surface smooth and neat, complete in all respects all as specified and directed. |
| 24 | S&F powder coated sliding type (min powder coating 50 micron) anodised aluminium frame for doors, windows & ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed |
| 25 | S&F powder coated(powder coating min 50 micron) anodised window and ventilator shutters two or three track sliding type or side hung/ without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete all as specified and directed. |
| 26 | S&F powder coated (powder coating min 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 27 | S&F 12 mm thick particle board preleminated on both side decorative choice etc complete all as specified and directed |
| 28 | S&F double action floor spring hydraulically regulated made up of aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed |
| 29 | S&F brass (extruded section body) door closer hydraulically regulated design No 2 etc universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed |
| 30 | S&F in repair of Mortice lock of 100mm size vertical type 4 lever etc complete all as specified and as directed etc complete all as specified and as directed |
| 31 | S&F W- hinges 75 mm medium weight, stainless steel and fixed complete all as specified and directed. |
| 32 | S&F Butt hinges 125mm, medium weight, stainless steel, and fixed complete all as specified and directed. |
| 33 | Supply and fix Extruded brass bow handles, of 150 mm size, fabricated type, polished complete all as specified and directed |
| 34 | S&F extruded brass designer handles fabricated type anodised of size 100 mm complete all as specified and directed. |
| 35 | S&F brass barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed. |
| 36 | S&F ball bearing / telescopic drawer channel of size 500 mm long complete all as specified and directed. |
| 37 | S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in all as specified and directed |
| 38 | S&F 6 lever Brass Matt finish door handle of 200mm long with 1xmortice lock, 1xstriker plate, 1xsquare shank including keys and all other necessary accessories fixed , colour and design as approved by GE complete all as specified and directed. |
| 39 | S&F 4.80 mm thick sheet glass quality and glazing fixed to aluminium frame n.exc 0.50 sqm complete all as specified and directed. |
| 40 | S&F 4.80 mm thick sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and directed. |
| 41 | S&F 8 mm thick sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and directed. |
| 42 | S&F Brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) 300mm size and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed. |
| 43 | Taking down cement plaster of any description on brick or stone walls etc. including raking out joint, hacking for key, scrubbing down with water etc incl patches of any size complete all as specified and directed. |
| 44 | M&L for 15mm thick rendering in cement mortar 1:4 on brick or concrete surfaces including rendering on fins , fascias, chajjas, parapets etc. and finishing the surfaces even and fair without using extra cement complete all as specified and directed. |
| 45 | M&L for 10mm thick rendering in cement mortar 1:6 on brick or concrete surfaces including finishing the surfaces even and fair without using extra cement complete all as specified and directed. |
| 46 | M&L for Precast cement concrete block masonry with solid block exc 10 Cm in width with PCC, type C1 (1:3:6) using 20mm graded crushed stone aggregate) and setting in CM 1:6 complete all as specified and directed. |
| 47 | M&L Precast cement concrete block masonry with solid block , not exc 10 Cm thick, type C1 (1:3:6) (using 20mm graded crushed stone aggregate) with plain or interlocking joints and setting in CM 1:4 complete all as specified and directed. |
| 48 | S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tenssile strength of 550 Mpa as in roof covering / cladding including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, complete all as specified and directed. |
| 49 | S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tenssile strength of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed. |
| 50 | M&L for 25 mm thick Cement concrete type B-1, 1:2:4 Mix (using 20 mm graded crushed stone aggregate) used over sub base to recd floor tiles complete all as specified and directed |
| 51 | M&L for Virified Ceramic tiles 9-10 mm thick dark shade (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00Sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified and directed. |
| 52 | All as per Item No 51 above here–in–before but on vertical surfaces such as skirtings and risers to steps etc. over 10mm thick rendering in CM 1:4 as in backing coat complete all as specified and directed. |
| 53 | M&L for 10mm thick coloured WPC/Charcoal louvers panel fixed with ply or metal base stuck sheet suitably placed in false ceiling/wall panelling, grid made of Aluminium /G.I./M.S. or wooden fillets or fixing with suitable adhesive or as per manufacturer instruction as per specification and drawings complete all as specified and directed. |
| 54 | M&L for 18/20mm thk granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and incl pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite over and including 20 mm thick cement screed bed in CM 1:4 complete all as specified and directed. |
| 55 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking plateform, and other similar situation complete all as specified and directed. |
| 56 | M&L for 75 mm thick cement concrete 1:2:4 Mix, type B-2 (using 40mm graded crushed stone agg) as in plinth protection finished even and smooth without using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified and directed. |
| 57 | Excavation in post holes each n.exc. 0.5 cum in soft/loose soil getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layer n.exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 mtr and making good surface complete all as specified and directed. |
| 58 | M&L Cement concrete type B-1, 1:2:4 (Using 20mm graded crushed stone aggregate) as in sub base,foundation filling and mass concrete etc.complete all as specified and directed. |
| 59 | S&F steel work as in tubular , rafters, purlins, posts and similar work (round/square/rectangular shape of pipes as approved by Engr-in-charge ) trusses of semi circle/ curved shape up to height 6 mtr including post special shaped washers, gusset plates etc complete using ERW or induction butt welded tubes conformining to IS 1161-1998 garde St-240 complete all as specified and directed. |
| 60 | Supply and Fix half round PVC rain gutter of dia 150 mm including jointing members , clamps, bolts and nuts fixed with eaves board or wooden any wooden or metal members complete all as specified and directed. |
| 61 | S&F 150 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and directed. |
| 62 | S&F PVC (SWR) bends 150mm dia complete all as specified and directed. |
| 63 | S&F MS framed work such as grills, gratings, etc with ends of bars, shouldered and/ or riveted or forged into spikes framed guard bars, barred iron doors, ladders, framed balusters, walk way, railing and framed work of water tanks and similar work confirming to Fe 290 Gde E-165 complete all as specified and as directed. |
| 64 | M & L for preparation of new plastered/concrete surfaces of walls, providing 1 mm thick of white wall care putty or cement paste to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint complete all as specified and directed. |
| 65 | M&L for preparation of new steel surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat red oxide primer complete all as specified and directed. |
| 66 | M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 67 | M&L for preparation of plastered or unplastered old decorated surfaces of walls by washing rubbing down and stopping of any external painted surfaces and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller incl filling of holes and cracks with suitable material like cement or plaster of paris etc complete all as specified and as directed. |
| 68 | M&L for preparation of new plastered/concrete surfaces of walls and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller etc complete all as specified and as directed. |
| 69 | M&L for providing PCC coping, using cement concrete1:2:4 Mix, type B-1 (using 20mm graded crushed stone aggregate) including necessary form work complete all as specified and directed. |
| 70 | M&L for 100 mm thick cement concrete 1:3:6, type C-2 (using 40mm graded agg) as in floor finished even and smooth without using extra cement complete all as specified and directed . |
| 71 | M&L for 15 mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified by Engr-in-Charge. |
| 72 | M&L for 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as s[ecified and directed. |
| 73 | S&F PVC (SWR) bends 75mm dia complete all as specified and directed |
| 74 | Dismantling floor, hearth , wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 75 | Red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 76 | M & L for hardcore of broken brick/stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified and directed. |
| 77 | M&L for walling of random rubber masonry, uncoarsed, well bounded, bedded and solidly hearted built in cement mortar 1:4 complete all as specified and directed. |
| 78 | M&L for plain cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) as in roof kerbs / pavings or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 79 | M & L PCC 1:3:6 type C-1 (20 mm graded crushed stone aggregate) as in bond stone set in CM 1:4 complete all as specified and directed. |
| 80 | Extra over stone walling for hammer dressing to face stones and with maximum depression on face beds from straight edge held against the dressed surface n exc. 40mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and directed. |
| 81 | Flush Pointing to random or polygonal rubble, uncrushed or brought upto course in CM 1:3 complete all as specified and directed. |
| 82 | M&L for 100mm thick PCC 1:4:8 type D-2 as in sub base finished even and rough complete all as specified and directed. |
| 83 | M&L for vitrified ceramic tiles dark shed (exterior grade), 10 mm thick(square /rectangular), polished, area of each tile n exc 0.36 sqm in floor etc , laid over and including 15 mm thick screed bed 1:6 ,set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and directed. |
| 84 | M&L for 60mm thick coloured, machine pressed precast concrete rubber moulded interlocking paver block any shape and size confirming to IS 15658-2006, M-40 grade with grey cement and and pigment complete all as specificied and directed |
| 85 | M & L for sand filling under floors or in pavings including watering and consolidation complete all as specified and directed.. |
| 86 | Supply & fix PVC SWR conduit pipes 110 mm dia in any length with rubber ring joints laid in trenches or in floor or as in weep holes complete all as specified and directed. |
| 87 | M&L for preparation of new plastered/concrete surfaces of walls and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller etc complete all as specified and directed. |
| 88 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 89 | M&L for a) Surface Prep: Ensure the RCC roof is clean, dry, and free from loose material, dust, or oil.b) Crack Repair: Seal cracks with Sikadur-20 Crack Seal or a similar sealant.c) Primer Application: Apply a suitable primer (like Sikalastic-11 Primer W) to enhance adhesion.d) Base Coat: Apply the first Sikalastic-560, generous coat with the help of roller.e) Reinforcement: While the base coat is still wet, embed Sika Reemat/Fleece-120 (fiberglass reinforcement) into the coat to enhance tensile strength.f) Top Coat: After the first coat has dried (typically touch-dry), apply a second of Sikalastic-560, top coat of the liquid membrane in a perpendicular direction to the first coat to ensure 100% coverage.g) The entire item to be executed through certified specialist firm/expert person with warranty of 5 yrs. |
| 90 | M&L for repair to damaged roof after complete removal existing treatment including padding, cleaning. the surface using wire brush brooming down and applying the following treatment all as directed in order of precedence as stated:-(a) Applying one coat of bituminious primer. (Note:- Bituminous primer shall be 'TANK MASTIC' manufactured by M/S STP Ltd or \\"EMUFALTE\\" Manufactured by M/s Texsa India Ltd)(b) Supply and laying 3 mm thick APP based polymeric membrane of approved manufactured with weight not less than 3.00 Kg/Sqm reinforced with non-woven polyester febric weight not less than 150 gms per Sqm. Polymeric membrance shall be taken to a height of 75mm (minimum) and than inserted inside the groove of parapet wall and shall be finished by a membrance flashing. Note:- Laying APP based polymeric membrane shall be done torch on method as per manufacturers instructions |
| 91 | M&L for 5mm thick plastering in CM with nano filler 1: Cement 1: Sand 3 on concrete surfaces as in sides of column, lintel, beam, chajja, facia railing, RCC, wardrobe etc including finish the surface even and fair without using extra cement complete all as specified and directed.Note: Nano material shall be measured and paid separately. |
| 92 | M&L for 20mm thick plastering in CM with nano wall filler 1: Cement 1: Sand 4 in two layers, top layer mixed with integral water proofing liquid admixture as per manufacturers instruction on brick or concrete surfaces of wall finished the surface fair and even complete all as specified and directed.Note: WPC& Nano material shall be measured and paid separately. |
| 93 | M&L for 15mm thick plastering in CM with nano wall filler 1: Cement 1: Sand 6 on fair face of brick or concrete surfaces, finished the surface fair and even and smooth without using extra cement complete all as specified and as directed.Note: Nano material shall be measured and paid separately. |
| 94 | Supply only nanotechnology based elastomeric hydrophobic powder/admixture(EHP) powder for cement plaster and concrete complete all as specified and directed. |
| 95 | M&L for PCC 1:2:4 Mix, Type B0 (using 12.5 mm graded crushed stone aggregate) as in levelling course, haunching, coping and similar works of over RCC roof surface including rounded or chamferred on edges etc complete all as specified and directed. |
| 96 | Repair to sunken per 1 sqm area including taking down plater/rendering, cleaning, sweeping removing dust and mud, or water, scoring sunken surfaces of bathroom/toilet etc and filling or levelling of roof surface by using concrete (1:2:4, with WPC over 0.90mm polythene sheet) CM 1:3 rendering and neeru finish to plastering as specified and make sure sunken is water proof by ponding of 48hrs complete all as specified and directed. |
| 97 | M&L for non skid ceremic white tiles 7 to 8mm thk area of each tile exc 0.06 sqm but n exc 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to mortar.Laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified and directed |
| 98 | M & L Glazed ceramic Coloured Tile 300x450x7mm/300x600x7 mm thick in Skirting, Dados, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Colour Cement to match laid over and including a backing coat of 10mm thick CM 1:4 screed, complete all as specified and directed. |
| 99 | Dismantling of plain or corrugated steel sheeting any guage thickness including nainital or similar pattern roof covering complete all as specified and directed. |
| 100 | Dismantling wrought Iron or mild steel work of any description not other wise described complete all as specified and directed. |
| 101 | M&L for roof truss (framed) trussed, purlin etc of angle or other section for refixing of sheets and similar works complete of Gde Fe-290 (Gde E-165) complete all as specified and directed. |
| 102 | M&L for preparing newly plastered or unplasterd surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed. |
| 103 | M&L for applying 1 mm thick plaster of paris over plastered surfaces to prepare the surface even and smooth complete all as specified and directed. |
| 104 | Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan point controlled by one, one way switch complete all as specified and directed. |
| 105 | Description all as per Srl item No 104 here in before but for socket outlet point 5 Amp on same board. |
| 106 | Description all as per Srl item No. 104 here in before but for socket outlet point 5 Amp on Independent board. |
| 107 | Description all as per serial item No 104 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified and directed. |
| 108 | Supply and fixing modular switch 1 way 6 A with cover plate and frame 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. |
| 109 | Supply and fixing modular switch 1 way 16 A with cover plate and frame230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. |
| 110 | Supply and fixing modular sockets with cover plate and frame 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and directed. |
| 111 | Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module with cover plate and frame 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. |
| 112 | S & F LED Luminaries 600mm x 600mm 36 watt, 220 V, AC recessed type with hifg efficiency PMMA diffuser soft galre free light complete with driver, holders and LED lamps suitable for roof ceiling including connecting up with 3 core flexible wire complete all asspecified and directed. |
| 113 | S&F lamp holder, insulated body, with back plate for batten fitting complete all as specified and directed. |
| 114 | Supply and fix in repairs LED lamp 7 Watt B22 base Color Temp 6500 K complete including taking down old unserviceable one complete all as specified and directed. |
| 115 | Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. |
| 116 | Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed |
| 117 | Supply and fix in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's.complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 01, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Oct 08, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 daysOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysOct 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender