Tender For Repair/ Replacement Of Roof Sheet, Plain Cement Concrete Hard Standing, Interlocking Paver Block, Ms Gate, Wpc Jalli And Other Connected Misc Work Under The Aor Of Age B/R Bhdc Under Ge (East) Delhi Cantt-10
Tender Value
49 Lakhs
Estimated cost
Bid Submission
01 Oct 2026
17 days left
EMD
98000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Replacement Of Roof Sheet, Plain Cement Concrete Hard Standing, Interlocking Paver Block, Ms Gate, Wpc Jalli And Other Connected Misc Work Under The Aor Of Age B/R Bhdc Under Ge (East) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | S&F in repair, in position Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of approved colour, having tensile strength of 550 MPA as in roof covering/cladding to wall, Chajja etc fixed with self tapping screws as specified, high tensile alloy steel trap sheet having 55 MPA yield strength and zinc (galvanized) + Aluminium combined, coating of 150 GSM/PM2(AZ-150) of 50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDEP polyester of 18 to 20 micron and back coat of 5 to7 micron Epoxy primer fixes, RMR 1040 profile width 1125 mm complete all as specified & as directed. |
| 2 | Description all as per item No 01.00 here in before but plain sheet as in ridge/valley/gutter complete all as specified & as directed. |
| 3 | S & F in repairs 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixe with coach screw and washer in roof, wall etc. complete all as specified and directed. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-charge. |
| 5 | Dismantling wood of any description Scantling / frame Work / trusses/purlin/ rafter/rails/ festenings /beam/posts/door frames etc of any size and shape complete all as specified and directed. |
| 6 | S&F mild steel rolled sections, Framed work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, using FE-290 (Gde-E-165) complete all as specified and directed. |
| 7 | S&F mild steel joist channel angle for posts and struts in fencing, gate, tank staging and manhole/drain cover including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 including demolition of old RCC/ CC manhole cover, complete all as specified and directed by Engr-in-Charge. |
| 8 | Demolition of brick work/stone bulder masonary built in cement mortar or cement lime mortar of any description and in any position all as specified. |
| 9 | M & L for brick work with sub-class B brick straight or curved on plan built in cement mortar 1 : 6 complete all as specified and directed |
| 10 | Taking down cement plaster/Grit plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc |
| 11 | M & L 15 mm thick rendering in cement mortar (1:4), on brick or concrete wall surface, mixed with water proofing compound @ 3% by weight of cement, finished fair & even without using extra cement complete all as specified and as directed. |
| 12 | Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge. |
| 13 | M&L preparation of new plastered wall surfaces and applying two coats of weather proof Exterior emulsion paint of colour & shade as approved (Colour scheme shall be as approved by the GE & user) over and including a coat of priming paint, over and including 3 mm thick cement based wall care putty complete all as specified and as directed. Make - Asian Apex Ultima or equivalent of make specified in PS. |
| 14 | M & L for washed stone grit plaster on exterior walls in two layers, under layers 12 mm thick cement plaster 1:4 (1 cement :4 coarse sand) following the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer with 15 mm thick cement plaster 1:½:2 (1 cement: ½ coarse sand:2 coloured marble stone chipping 10mm nominal size) including using Colour pigment & marble powder as required in ground in panels with groove all around as per approved pattern including scrubbing and washing the top layer with wire brushes and water to expose the stone chippings includind forming groove of uniform size 15mm wide and 15mm deep as per approved pattern complete all as specified and as directed. |
| 15 | Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified. |
| 16 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge. |
| 17 | Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floor, aprons etc and including disposal of all debris exc 1.5 KM not exc 5 Km. |
| 18 | M&L for 50 mm PCC type C -2 (1:3:6) using 40 mm graded crushed stone aggregate as in Sub base/levelling course complete all as specified and directed. |
| 19 | M&L for 20-25 mm thick machine cut kota stone slab flooring jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and incl 20 mm thick screed bed of CM 1:4 including rubbing and polishing complete all as specified and directed by Engr -in Charge. |
| 20 | M&L for 18-20 mm thick machine cut kota stone slab in riser, steps and skirting jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab laid over 15 mm thick screed bed of CM 1:3 including rubbing and polishing complete all as specified and directed by Engr-in-Charge. |
| 21 | M&L for chequered cement concrete tiles with grey cement & pigments, size 20cmx 20cm/ 30cmx30cmx 25 mm thick, set, jointed and pointed in neat cement slurry pigmented to match colour/shade of tiles as in floors etc.; laid over & including 20 mm thick screed bed or bedding layer in CM 1:6, etc complete all as specified and directed by Engr-in-Charge. |
| 22 | M&L for 100mm PCC type D -2 (1:4:8) using 40 mm graded crushed stone aggregate as in Sub base complete all as specified and directed. |
| 23 | M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour in any design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 24 | M&L for 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 25 | Providing and laying 40 mm thick precast cement concrete chequered tiles for footpath, of approved size, colour, pattern and finish, machine-made from cement and graded coarse/ fine aggregates, having uniform thickness and a chequered/non-slip surface, over a prepared base/bed of cement mortar 1:4 (1 cement : 4 coarse sand) of required thickness, including proper dressing, levelling, alignment and compaction of the base, laying of tiles to required line and level, cutting and fitting to required shape at edges and around obstructions, maintaining uniform joints, filling joints with cement slurry/mortar over and incl 20mm thcik screed bedding layer in CM 1:6, curing, cleaning and all other incidental works, complete in all respects as directed by the Engineer-in-Charge. |
| 26 | M&L for heavy duty coloured (approved colour) fully vitrified anti-skid paving tiles of size 400 x 400 mm and 11–12 mm thick, suitable for outdoor use, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry. Joints shall be 3–5 mm wide and pointed in coloured or white cement to match the shade of tiles, including cleaning of surface after laying, complete all as specified and as directed by Engineer-in-Charge. |
| 27 | M&L for heavy duty coloured (approved colour) fully vitrified anti-skid paving tiles of size 300x300 mm and 11–12 mm thick, suitable for outdoor use, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry. Joints shall be 3–5 mm wide and pointed in coloured or white cement to match the shade of tiles, including cleaning of surface after laying, complete all as specified and as directed by Engineer-in-Charge. |
| 28 | M&L for heavy duty coloured (approved colour) semi vitrified paving tiles of size 300 x 300 mm x 9 to 10 mm thick, set and jointed in neat cement slurry and pointed in coloured or white cement to match the shade of tiles over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed. |
| 29 | Excavation in post hole (similar hole) each N Exc 0.5 Cum getting out, returning filling and ramming earth or brocken rubble mixed with earth around in layer not exc 25 CM watering and removing surplus soil to a distance N Exc 50 M and making good surface complete all as specifide and directed. |
| 30 | Plain Cement Concrete Type C1 (1:3:6) (using 40 mm graded stone aggregate)in foundation filling and mass concrete complete all as specified and directed. |
| 31 | M&L for two coats of synthetic enamel paint over a coat of Red oxide primer on new Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 32 | M&L for one coat of synthetic enamel paint on old Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 33 | Providing, fabricating and fixing 24 mm thick WPC (Wood Plastic Composite) decorative jalli, suitable for outdoor application, manufactured through single extrusion process, comprising K-Value 58–60 (Suspension Grade) PVC resin, calcium carbonate and natural fibres (wood powder /rice husk/wheat husk) with non-toxic additives, having minimum density of 650 kg/cum, good screw holding capacity with minimum screw withdrawal strength of 2000 N (face) and 1100 N (edge), minimum compressive strength of 50 N/mm², modulus of elasticity not less than 850 N/mm² and resistance to spread of flame Class ‘A’ category, termite/borer free, water/moisture proof and fire resistant, of approved make manufactured by an ISO 9001:2015 certified company, cut to required size and fixed in position in MS angle frame of appropriate size including fabrication of MS frame by cutting, welding, grinding, alignment, levelling and plumbing complete, MS frame treated with one coat of red oxide zinc chromate primer and two coats of approved synthetic enamel paint suitable for exterior exposure, rate inclusive of cost of all materials, labour, tools, plants, scaffolding and sundries, complete in all respects and as directed by Engineer-in-Charge. (Make - Rajshri or Equivalent). Note:- The said item shall be fixed over boundary wall/ roof tops and in any other position as required on site. |
| 34 | S&F in repair of 75 mm thick factory-made SFRC medium duty (Steel Fibre Reinforced Concrete) manhole/drain covers of approved shape and size, including careful demolition and removal of existing/damaged manhole/drain covers, breaking the same into manageable pieces, lifting, loading, transporting and dumping/disposal of the demolished material at low-lying areas as directed by the Engineer-in-Charge, including all labour, tools, tackles and incidental works, complete in all respects as specified and directed. |
| 35 | S&F in repair stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including dismantling of existing MS/SS Grill complete all as specified and as directed. |
| 36 | M&L 75 mm thick PCC 1:3:6, type C1, using (using 20mm graded aggregate) as in Plinth protection and finished the surface fair & even without using extra cement, laid in panel , including filling the joints with sand mixed with bitumen in 1:1 ration complete all as specified and directed. |
| 37 | S&Fin repair Kerb stone of 300x300x100mm thick precasted plain cement concrete type B0 1:2:4 (using 12.5mm graded crushed stone aggregate) incl earth work for laying kerb stones. |
| 38 | M&L for complete removal of existing treatment from old decorated walls by scraping with mechanical sander of asian paints trucare wall sander or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scarping tools where mechnical removal is not possible complete all as specified and directed by Engr-in charge and applying two coats of weather proofing exterior emulsion paint (Apex Ultima Luxury emulsion of Asian or equivalent of approved make as approved by GE) incl one coat of exterior primer up to 5 story bldg by using smart periodical methodology (spray machine) complete all as specified and directed. Note:- rate quoted up to G+4 bldg including scaffolding. |
| 39 | M&L for preparation of pathway/Flooring (Over Interlocking/Chequired tile surface) or any type of surfaces old/New or any position and applying one coat of floor paint of superior quality complete all as specified and as directed. |
| 40 | Disposal of building rubbish/malba, similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading and disposal at an approved Municipal dumping ground outside Defence land (MoD land), for all leads and all lifts, complete all as specified and as directed by the Engineer-in-Charge.Notes:1. Photographic Evidence: The contractor shall submit clear photographic evidence in support of disposal of building rubbish/malba, similar unserviceable, dismantled or waste materials, indicating the condition of the site before loading, during transportation and after unloading at the approved Municipal dumping ground. The photographs shall preferably be geo-tagged and date-stamped and shall form part of the record for verification and payment purposes. 2. Certification by Engineer-in-Charge: Completion of whole work in this BOQ shall be deemed to have been achieved only after certification by the Engineer-in-Charge that no building rubbish/malba, similar unserviceable, dismantled or waste materials have been left at the site and that the site has been thoroughly cleared and cleaned to his satisfaction. 3. Each load shall comprise a minimum carrying capacity of 5.00 cubic metres (Cum). Payment under this item shall be made on a per-load basis for loads conforming to the above minimum capacity and duly verified by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender