Tender For Welcome And Comprehensive Maintenance In Officers Md Accn Under Age B/R-I Of Ge Saugor
Tender Value
25 Lakhs
Estimated cost
Bid Submission
03 Oct 2026
0 days left
EMD
50000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sagar → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Welcome And Comprehensive Maintenance In Officers Md Accn Under Age B/R-I Of Ge Saugor
BOQ
| Sl. No. | Item Description |
| 1 | M&L for one coats of white wash on old decorative wall surfaces including preparation of surface by brooming down with steel wire brushes scraping down moulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , cracks etc complete all as specified and directed. |
| 2 | M&L for one coats of white wash on old decorative ceiling surfaces including preparation of surface by, brooming down with steel wire brushes scraping down moulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , cracks etc complete all as specified and directed. |
| 3 | M&L for two coats of white wash on old decorative wall surfaces including preparation of surface by brooming down with steel wire brushes scraping down moulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , cracks etc complete all as specified and directed. |
| 4 | M&L for one coats of Distemper oil emulsion on old decorative wall surfaces including preparation of surface by brooming down with steel wire brushes scraping down moulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , cracks etc complete all as specified and directed. |
| 5 | M&L for two coats of Distemper oil emulsion on old decorative wall surfaces including preparation of surface by brooming down with steel wire brushes scraping down moulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , cracks etc complete all as specified and directed. |
| 6 | M&L for one coats of synthetic enamel paint on old wooden or wood based surfaces of any description, not otherwise descri-bed, over 10cm width or girth including preparation of surfaces complete all as specified and directed. |
| 7 | M&L for two coats of synthetic enamel paint on old wooden or wood based surfaces of any description, not otherwise descri-bed, over 10cm width or girth including preparation of surfaces complete all as specified and directed. |
| 8 | M&L for one coats of synthetic enamel paint on old Steel and iron surfaces of any description, not otherwise descri-bed, over 10cm width or girth including preparation of surfaces complete all as specified and directed. |
| 9 | M&L for two coats of synthetic enamel paint on old Steel and iron surfaces of any description, not otherwise descri-bed, over 10cm width or girth including preparation of surfaces complete all as specified and directed. |
| 10 | M&L for two coats of cement base wall care putty in two coats @ 1Kg/Sqm (0.5Kg in each coat) on new plastered surface of wall/ceiling by fully automatic airless spray machine as preparatory work to painting including cleaning surface before application of putty and necessary rubbing of puttied surface with appropriate size of sand paper so as to make the surface truly smooth, free from all dirt/ dust and made ready to receive the finishing coat of paint complete all as specified and directed.Make : Birla white / JK putty/ Berger |
| 11 | M&L for applying two coats of acrylic exterior emulsion paint over and including one coat of exterior primer on prepared surfaces of wall by fully automatic airless spray machine complete all as specified and directed.Make : Asian (Appex Altima)/ Berger(weather coat all Guard)/ Nerolac(Excel total)Note : (i) The emulsion used shall be of approved colour by GE diluted as per manufacturer's instructions |
| 12 | M&L for two coat of acrylic interior emulsion paint over and including one coat of interior primer by fully automatic airless spray machine on prepared surfaces of wall/ceiling complete all as specified and directedMake : Asian (Apcolite)/ Berger(self breath easy)/ Nerolac(nerolac Impression HD)Note : (i) The emulsion used shall be of approved colour by GE diluted as per manufacturer's instructions(ii) Contractor shall ensure washing floors, cleaning glass, joinery, electric fitting, etc after painting work with entire satisfaction of Engg-in-charge. |
| 13 | M&L for complete removal of existing treatment using mechanical scrapping machine and applying two coats of cement base wall care putty by fully automatic airless spray machine in two coats @ 1Kg/Sqm (0.5Kg in each coat) on of wall/ceiling surfaces as preparatory work to painting including removing of nails, making good holes, cracks etc cleaning surface before application of putty and necessary rubbing of puttied surface with appropriate size of sand paper so as to make the surface truly smooth, free from all dirt/ dust and ready to receive the finishing coat of paint complete all as specified and directed.Make : Birla white / JK putty/ Berger |
| 14 | M&L for one coats of weather proof extirior paint on old decorative wall surfaces including preparation of surface by brooming down with steel wire brushes scraping down moulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , cracks etc complete all as specified and directed. |
| 15 | S&F in repair purposely moulded looking mirror 5mm thick glass (width not less than 600mm) fixed with studs complete all as specified and directed.Make : Saint-Goblin/Modi Guard/Asahi India (AIS) |
| 16 | Taking down chowkhat or frame (without taking off shutter from the frame), area of opening exc 1.5 sqm and n'exc 4.00 sqm each, removing from the site complete all as specified and directed.Note:- In order to facilitate the taking down of chowkhat or frame with holdfasts, the cost of cutting holes or dismantling of brick/stone/concrete masonry work of any description in Jambs of existing opening or removing any other fixing arrangement and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B-1 as required so as to re-fix the holdfasts of new chowkhat or frame shall deemed included in quoted unit rates.(ii) Hold fast / fasteners shall be measured and paid separately in respective item hereunder |
| 17 | Taking down chowkhat or frame (without taking off shutter from the frame), area of opening n'exc 1.5 Sqm each, removing from the site complete all as specified and directed.Note:- In order to facilitate the taking down of chowkhat or frame with holdfasts, the cost of cutting holes or dismantling of brick/stone/concrete masonry work of any description in Jambs of existing opening or removing any other fixing arrangement and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B-1 as required so as to re-fix the holdfasts of new chowkhat or frame shall deemed included in quoted unit rates.(ii) Hold fast / fasteners shall be measured and paid separately in respective item hereunder. |
| 18 | Taking down shutters of any description, area exc 1 Sqm but n'exc 2.00 Sqm each complete all as specified and directed. |
| 19 | Taking down shutters of any description, area n'exc 1.00 Sqm each complete all as specified and directed. |
| 20 | M&L for Second class hard-wood in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed. |
| 21 | S&F 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 22 | M&L for 2nd class HW (Teak) glazed and skeleton shutters ( factory made), 35 mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, cla-use 8.24 (a); for doors supplied and fitted to chowkhats complete all as specified and directed.Note: (i) The glass and wire gauge shall be measured and paid separately under respective item here under. |
| 23 | S&F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single sideprelam colour PVC sheet, reinforced with M.S. Square tube including painting edges to match with prelam sheet, fixed in opening as per specification & drawing complete all as specified and directed. |
| 24 | S&F Factory made 30mm thick (stiles), Solid PVC Moulded Door Shutter with wood free EPS, with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, fixed in frame at site as per specification & drawing complete all as specified and directed. |
| 25 | S&F fixed type ventilators aluminium powder coated of frame size 50.80X 25.40mm,1.5 mm thick half portion will be fixed with 4mm thick frosted glass and half portion will be fixed with louvers with 4mm thick frosted glass with rubber gasket and aluminium beading ,aluminium wire mess 0.36 mm dia and width of aperture 1.45mm to be fixed over louvers portion only including necessary cutting holes on wall and fixing arrangements complete all as specified and directed.Note : Aluminium section(s) thickness shall not be not less than 1.50 mm. |
| 26 | S&F for powder coated aluminum glazed window, three track-sliding type using 1.80 mm thick aluminium open section having size of style & top rails 83x44mm, bottom rails 100x44mm including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading screws, anodised aluminium fittings complete and including glazing by using 5mm thick plain sheet glass and stainless steel wire mess of dia 0.36mm and aperture 1.4mm, complete all as specified and as directed. ((Note-glazed shutters glass thickness not less than 5.00 MM and wiremess shutter with SS wiremesh as approved by GE is also included. No extra payment will be made separately) |
| 27 | M&L for aluminium work with powder coated aluminium sections as in door (frame and shutters), any No of Panels, openable both side on pivot arrangment (Floor door spring and pivot set), glazing with 4.8 mm thick plain/ ordinary sheet glass fixed with rubber gasket and aluminum glazing clips, 2x Stainless steel Handle, locking arrangment, 01x Tower bolt and fixed in position with adiquate Number of fastners/ hold fast including cutting holes in wall/floor and making good (if required) complete all as specified and directed.Note :(X) Aluminium sections shall be powder coated and of folllowing sizses:- (A) FRAME :(i) Rectangular tube section 100x44x1.60 to1.8 mm thick(B) SHUTTERS(i) Styles 85 x 44.45 x 3mm thick section No- 4526(ii) Top rail 95.25 x 44.45 x 1.7 mm thick section No-4553 (iii) Middle/lock rail 83.50 x 44.45 x 1.7 mm thick section No-4565(iv) Bottom rail 114.3 x 44.45 x 2.82 mm thick section No-4529(v) Glazing clip 0.70 mm thick section N0-4407(vi) Handle: Stainless steel handle 200mm long of aproved design and pattern (vii) Tower bolt: 9.90 mm dia sheet and section Ano-40027, 200 mm long(viii) Mortic lock: 100 mm size 4 lever. Make : Godrej(Y) Floor door spring and pivot set shall be measured and paid seperatly. |
| 28 | S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 29 | S&F in repair 25mm dia stainless steel (202 Grade) curtain rod not less than 0.70mm thick with decorative end caps (Latoo) and brackets complete all as specified and directed.Note : In openings exceeding 1.2m wide, additional brackets shall be provided so as the distance between two consecutive brackets shall not exceed 1.2m. |
| 30 | S&F100mm long stainless steel butt hinges, 304 grade, heavy-duty, corrosion-resistant (rust preventive), polished / Bright (e.g., #8 Mirror Finish), fixed with stainless steel screws complete all as specified and directed. |
| 31 | S&F 200mm long stainless steel barrel tower bolt, 304 grade, heavy-duty, corrosion-resistant (rust preventive), polished / Bright (e.g., #8 Mirror Finish), fixed with stainless steel screws complete all as specified and directed. |
| 32 | S&F 125mm size stainless steel handle, 304 grade, heavy-duty, corrosion-resistant (rust preventive), polished / Bright (e.g., #8 Mirror Finish), fixed with stainless steel screws complete all as specified and directed. |
| 33 | S&F 300mm long stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, 304 grade, heavy-duty, corrosion-resistant (rust preventive), polished / Bright (e.g., #8 Mirror Finish), fixed with stainless steel nut & bolts and fixed complete all as specified and directed. |
| 34 | S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.45mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and directed. |
| 35 | S&F in repair 18 to 19mm thick marine ply wood, interior grade, laminated one side with 1mm thick coloured mica and other side with 1mm thikc white mica, as in cupboards, shelves, pelmets etc, cut to required size and fixed to frame complete all as specified & directed. |
| 36 | S&F in repair stainless steel Continuous (piano) hinges, width of flaps (when open)- 30mm, 304 grade, heavy-duty, corrosion-resistant (rust preventive), polished / Bright (e.g., #8 Mirror Finish), fixed with stainless steel screws complete all as specified and directed. |
| 37 | S&F 40mm dia brass, polished, bright finished cupboard knobs fixed with nut, screw and washer as etc. complete all as specified and directed. |
| 38 | S&F 100mm long stainless steel hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed. |
| 39 | S&F metal body magnatic ball catches with striking plate, heavy duty fixed with stainless steel screws complete all as specified & directed. |
| 40 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed |
| 41 | M&L for Brick work with sub- class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed |
| 42 | Demolition of cement concrete (unreinforced) in ground floors and pavings (below or above ground level), n exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 43 | M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 44 | M&L for 75mm thick PCC 1:3:6 type C-2, (using 40mm graded stone aggregates) as in plinth protection finishing surface even and smooth without using extra cement including providing construction joint (at an interval not more than 3.0m) and filled with bitumen and sand mortar in 1:3 complete all as specified and directed. |
| 45 | M&L for 25mm thick PCC (1:2:4) type B-0 (using12.50mm graded stone aggregate) as in levelling course to sub base, finished surface rough to receive the tiles complete all as specified and directed. |
| 46 | M&L for Dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), any description including removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 47 | M&L for full body vitrified ceramic coloured tiles in floors etc, 8 to 10mm thick, area of each tiles exc 0.36 sqm but n'exc 1.20 sqm (square/ rectangular) tiles, set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour/shade over and including 15mm thick screed bed layer in CM 1:6 complete all as specified and directed. |
| 48 | All as per item 47 above but as in Dado/skirting fixed over and including 10mm thick rendering in CM (1:4). |
| 49 | M&L for Non skid ceramic coloured tiles in floors etc, 7 to 8mm thick, area of each tiles exc 0.18 sqm but n'exc 0.38 sqm (square/ rectangular) tiles, set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour/shade over and including 15mm thick screed bed layer in CM 1:6 complete all as specified and directed. |
| 50 | M&L for digital glazed ceramic tiles, coloured tiles 600mm x 300mm x 6-7mm thick on vertical surfaces ie. as in skirting/dado etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15 mm thick screed in cement mortar (1:4) complete all as specified and directed. |
| 51 | M&L for 16 to 18mm thick Granite slab of any shade (table rubbed and polished), machine cut for floors / shelves in steps, jambs, pillars, window cills & cooking platforms laid over and including 15 mm thick cement mortar 1:4 bedding, pointing in white cement 1:2 using marble dust with admixture of pigment to match shade of the slabs, complete all as specified and directed |
| 52 | M&L for rounding to the edge of stone slabs one edges such as in steps, cooking platform and other similar situations complete all as specified and as directed. |
| 53 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed |
| 54 | M&L for rendering cement plaster, 15mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:4 mixed with and including liquid water proofing compound @ 200ml per 50 kg bag of cement complete all as specified and directed.Note : Water roofing compound shall be measured and paid separately in respective item of this BOQ, |
| 55 | M&L for rendering cement plaster, 15mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6, finishing surfaces even and smooth without using extra cement complete all as specified and directed |
| 56 | M&L for rendering cement plaster, 5mm thick on fair faces of brick work or concrete surfaces on ceilings in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed. |
| 57 | M&L for applying three coats of white wash on newly plastered ceiling surfaces including preparation of these surfaces complete all as specified and directed. |
| 58 | M&L for GI tubing 15 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors including taking down existing tubing of any description complete all as specified and directedNote : Cutting chases and making good shall be measured and paid separately under respective item here-in-after. |
| 59 | M&L for GI tubing 20 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors including taking down existing tubing of any description complete all as specified and directedNote : Cutting chases and making good shall be measured and paid separately under respective item here-in-after. |
| 60 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads or from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed. |
| 61 | M&L for glazing with 3mm thick sheet glass ordinary quality and with oil putty in square, nexc 0.5 sqm in each pane complete all as specified and as directed.. |
| 62 | S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.45mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and directed. Please Enable Macros to View BoQ information |
| 63 | S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.45mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender