Tender For Certain Misc Repair Of Office Building, Air Crew Room, Tech Bldg, Hangers, Hard Standing And Connected Works At Army Avn Sqn (Uh) Under Age B/R-I And Age E/M-I Of Ge 865 Ews
Tender Value
83.42 Lakhs
Estimated cost
Bid Submission
08 Oct 2026
0 days left
EMD
1.50 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
leh → Ladakh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Certain Misc Repair Of Office Building, Air Crew Room, Tech Bldg, Hangers, Hard Standing And Connected Works At Army Avn Sqn (Uh) Under Age B/R-I And Age E/M-I Of Ge 865 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in ground floor and paving exc. 15cm thick below or above ground level, complete all as specified and/or as directed by Engr-in-Charge. |
| 2 | M&L for 100 mm PCC 1:3:6 type C-2 using 20mm graded aggregate as in floor of hard standing finished even and smooth without using extra cement, complete all as specified and/or as directed by Engr-in-Charge. |
| 3 | M&L for cement concrete work in pavement / hard standing of flexural strength 40 kg/sqcm in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less, complete all as specified and/or as directed by Engr-in-Charge. |
| 4 | Supply only polyester triangular fibres as secondary reinforcement in all type of concrete and mortar, complete all as specified and/or as directed by Engr-in-Charge. |
| 5 | M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' for 100mm thick concrete, complete all as specified and/or as directed by Engr-in-Charge. |
| 6 | Removing of demolition material not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and/or as directed by Engr-in-Charge. |
| 7 | Taking down shutters of any description area exceeding 1 sqm and not exc. 2 sqm each, complete all as specified and/or as directed by Engr-in-Charge. |
| 8 | S&F for 35mm thick 2nd class soft wood plain framed paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supply and fixed to chowkats, complete all as specified and/or as directed by Engr-in-Charge. |
| 9 | S&F mild steel butt hinges, medium weight cold rolled 100mm size, complete all as specified and/or as directed by Engr-in-Charge. |
| 10 | S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and/or as directed by Engr-in-Charge. |
| 11 | S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed, complete all as specified and/or as directed by Engr-in-Charge. |
| 12 | Dismantling floor, hearth or wall tiling including wall cement mortar, bedding (but not backing) and rubbish off premises, complete all as specified and/or as directed by Engr-in-Charge. |
| 13 | M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11 sqm and not exc 0.18 sqm in floor etc. set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the screed bed with CM (1:6) 15mm thick laying floor tiles, complete all as specified and/or as directed by Engr-in-Charge. |
| 14 | M&L for glazed ceramic coloured tiles in vertical surfaces 350mm x 250mm x 7mm / 450mm x 350mm x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:4) in dado/skirting tiles, complete all as specified and/or as directed by Engr-in-Charge. |
| 15 | M&L for 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in sub base of floor, complete all as specified and/or as directed by Engr-in-Charge. |
| 16 | S&F 500 litre capacity rotational moulded polyethylene water storage tank inner and out white, two layers ISI marked (Cylindrical vertical, with closed top), hoisted with threaded cap and fixed in position all as specified in SSR Part I including all accessories (i.e. GI nipple etc.), including provn of 20/25 mm dia spout for connecting inlet, outlet, over flow and washout pipes and including dismantling water tanks and removing to store exc. 250 litre and not exc. 500 ltrs capacity, complete all as specified and/or as directed by Engr-in-Charge. |
| 17 | S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gm/ 20mm-210gm/ 25mm-455gm/ 40mm- 690 gm), complete all as specified and/or as directed by Engr-in-Charge. |
| 18 | S&F in repair 25mm outer dia PPR ball valve (brass insert) conforming to ISO 2000 high pressure with epoxy coated aluminium rod and high density plastic ball screwed for PPR pipe or for union and fixed as per requirement of site, complete all as specified and/or as directed by Engr-in-Charge. |
| 19 | S&F in repair vitreous china wash down water closet (pedestal), white (EWC) excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including connection to drain pipe and to flushing pipe antisyphonage pipe etc. complete all as specified and/or as directed by Engr-in-Charge. Make : Cera/Jaquar/Kohler or equivalent as approved by GE. |
| 20 | S&F in repair one piece EWC of size 700 x 380 x 770 mm with built in cistern vitreous china wash down water closet (pedestal), white (EWC) including plastic seat of same colour of WC, closed pattern with flat bottom and cover and mild steel chromium plated hinging device fixed in repair connection to drain pipe and to flushing pipe antisyphonage pipe etc. including PVC fitting P or S trap for 100mm bore of pipe fixed, complete all as specified and/or as directed by Engr-in-Charge. Make : Cera/Jaquar/Kohler or equivalent as approved by GE. |
| 21 | S&F 25mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacturer's instructions and as directed by Engineer in Charge including taking up or down 25 mm bore steel tubing / PPR pipe and connections and set aside for re-use or removal to store. |
| 22 | S&F 32mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacturer's instructions and as directed by Engineer in Charge including taking up or down 32 mm bore steel tubing / PPR pipe and connections and set aside for re-use or removal to store. |
| 23 | S&F in repairs 750 mm long, 32/ 40 mm dia, PVC plain waste pipe for sinks / wash hand basins, complete all as specified and/or as directed by Engr-in-Charge. |
| 24 | S&F in repairs 40mm waste coupling of CP brass for sink and wash hand basin (half or full threaded ), complete all as specified and/or as directed by Engr-in-Charge. |
| 25 | S&F in repairs vitreous china wash basin white flat back size 550 x 400 mm excluding tap, waste, chain and plug and porcelain stopper but including cutting and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and/or as directed by Engr-in-Charge. Make : Jaquar/Cera or equivalent as approved by GE. |
| 26 | S&F in repair fancy type 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and/or as directed by Engr-in-Charge. |
| 27 | S&F in repairs 10 litre capacity PVC valveless symphonic action type, flushing cistern (ISI marked), low level, white, with inlet, ball valve, float and handle including bracket & flush pipe of polyethylene of low or high density or high density or PVC, 32mm dia for low level cistern, complete all as specified and/or as directed by Engr-in-Charge. |
| 28 | S&F in repair acrylic PVC bathroom cabinet of size 550 x 400 mm with openable shutter fixed with looking mirror of selected quality and with suitable shelves inside the cabinet of superior quality as approved and directed by Engr in Charge. |
| 29 | S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and/or as directed by Engr-in-Charge. Make: Cera/Jaquar or equivalent as approved by GE. |
| 30 | S&F in repair CP towel ring of dia 200mm fixed with and including screws and wooden/plastic cleats, complete all as specified and/or as directed by Engr-in-Charge. |
| 31 | S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and/or as directed by Engr-in-Charge. |
| 32 | S&F in repair CP floor gratings 150mm dia, complete all as specified and/or as directed by Engr-in-Charge. |
| 33 | S&F in repair fancy type glass corner self with CP brackets etc., complete all as specified and/or as directed by Engr-in-Charge. Make: Jaquar or equivalent as approved by GE. |
| 34 | S&F chromium plated brass soap dish (oval shape) to walls (size not less than 125mm long) complete fix to wall, complete all as specified and/or as directed by Engr-in-Charge. |
| 35 | S&F in repair toilet paper holder with flat recessed type stainless steel fixed with screws, complete all as specified and/or as directed by Engr-in-Charge. Make : Hindware/Jaquar or equivalent as approved by GE. |
| 36 | S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and/or as directed by Engr-in-Charge. Make : Cera/Jaquar/Hindware or equivalent as approved by GE. |
| 37 | S&F in repair WC plastic seat cover of size 490 x 370mm complete with all acessories, complete all as specified and/or as directed by Engr-in-Charge. |
| 38 | Dismantling plain or corrugated steel /fibre sheeting any guage thickness including nanital or similar pattern, complete all as specified and/or as directed by Engr-in-Charge. |
| 39 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and/or as directed by Engr-in-Charge. |
| 40 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws at appropriate height / level, complete all as specified and/or as directed by Engr-in-Charge. Note : Height approx 9m from floor level incl provision of hydra as per site requirement. |
| 41 | S&F fibre glass reinforced translucent plain sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and/or as directed by Engr-in-Charge. Note : Height approx 9m from floor level incl provision of hydra as per site requirement. |
| 42 | Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or as directed by Engr-in-Charge. |
| 43 | S&F MS rolled sections in main and cross beams, hip and jack rafters; purlins where connected to common rafters running rails and guids for sliding doors; fixed with angle cleats or other connecting plates and similar work conforming to Fe-290, Gde-E-165, complete all as specified and/or as directed by Engr-in-Charge. |
| 44 | S&F mild steel hand rails, flat iron, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bas for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed including all necessary drilling bolting or riveting etc. and similar work conforming to Fe 290 Gd E 165, complete all as specified and/or as directed by Engr-in-Charge. |
| 45 | M&L for two coats of synthetic enamel paint to steel surface over a coat of red oxide primer exc. 10 cm width or girth incl preparation of new surfaces, complete all as specified and/or as directed by Engr-in-Charge. |
| 46 | M&L for PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation filling and mass concrete, complete all as specified and/or as directed by Engr-in-Charge. |
| 47 | M&L for cement concrete type B-2,1:4:8 (40mm graded aggreate) 75 mm thick as in sub-floors, sub-bases, floors and pavings etc., complete all as specified and/or as directed by Engr-in-Charge. |
| 48 | M&L forming contraction (dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in floor surface of hard standing, complete all as specified and/or as directed by Engr-in-Charge. |
| 49 | S&F structural steel works as in tubular roof trusses, purlins, rafter, vertical posts, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular pipe, channel or flat sections) including distance pieces, cleats, riveting incl. bending and welding, conforming to Fe-410W Gde E-250 quality A, complete all as specified and/or as directed by Engr-in-Charge. |
| 50 | S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessary, gusset plates, cleats, MS flat, MS plate, rivetting etc. not exc. 10 kg each brackets, conforming to Fe 290 Gde E-165, complete all as specified and/or as directed by Engr-in-Charge. |
| 51 | M&L for angle iron as in fencing post, incl. cutting tops to shape as directed, drilling holes, notching for wire etc., flat iron fillets (for securing wire mess) incl. all necessary drilling, bolting or reveting etc., complete all as specified and/or as directed by Engr-in-Charge. |
| 52 | Supply only chain link MS galavanised fencing, complete all as specified and/or as directed by Engr-in-Charge. |
| 53 | Dismantling chain link fencing/expanded metal or mesh not exceeding 4kg/sqm fixed in steel, wood fillets, concrete post etc. of any description, complete all as specified and/or as directed by Engr-in-Charge. |
| 54 | Fixing only chain link fencing including line wires and mesh size type of standards, rails, straining bolts etc. size of mess 100mm x 100mm, 4mm dia wire, complete all as specified and/or as directed by Engr-in-Charge. |
| 55 | M&L for mild steel round bars 10mm dia and over cut to length bent to shape required and fixing as required in fencing, complete all as specified and/or as directed by Engr-in-Charge. |
| 56 | M&L for 40x6mm flat iron as in ties, incl cutting tops to shape as directed, drilling holes, notching for wire etc, complete all as specified and/or as directed by Engr-in-Charge. |
| 57 | S&F MS bolts machine made with hexagonal or square head one end and screwed the other or screwed both end not exc. 5 cm long 12mm dia, complete all as specified and/or as directed by Engr-in-Charge. |
| 58 | M&L for preparation of existing treatment on steel / CGI sheets of any description and applying two coats of synthetic enamel paint (galvanisation should be removed if required), complete all as specified and/or as directed by Engr-in-Charge. Note : Height approx 9m from ground level. |
| 59 | M&L for sand filling (50 mm average thickness) under floors in foundations and for laying Interlocking paver blocks including watering and consolidation, complete all as specified and/or as directed by Engr-in-Charge. |
| 60 | Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc. laid dry and pointed, complete all as specified and/or as directed by Engr-in-Charge. |
| 61 | M&L for machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment conforming to IS 15658-2006 of 60 mm thickiness M-35 grade, complete all as specified and/or as directed by Engr-in-Charge. |
| 62 | Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and/or as directed by Engr-in-Charge. |
| 63 | M&L for pre-cast cement concrete (20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonry with solid blocks exc.10cm in width and setting in cement mortar 1:6, complete all as specified and/or as directed by Engr-in-Charge. |
| 64 | M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including taking down, complete all as specified and/or as directed by Engr-in-Charge. |
| 65 | Supply only integral liquid water proofing compound.Make : Pidilite/Sika. |
| 66 | M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of chalk whiting, complete all as specified and/or as directed by Engr-in-Charge. |
| 67 | Demolition of stone slabs and tiles of any description or thickness in floors aprons etc. laid bedded and pointed in any mortar, complete all as specified and/or as directed by Engr-in-Charge. |
| 68 | M&L for chequered cement concrete tiles 30cm X 30cm X 20mm thick, set, pointed and jointed in neat cement slurry in floors polished with grey cement and pigments laid over 20mm thick cement screed base (1:6), complete all as specified and/or as directed by Engr-in-Charge. |
| 69 | Taking down carefully and refixing by mechanical means, steel hanger door shutters leaf of size 5.50x4.00m and keeping aside on the ground, repairing the parts/members of door, including minor repairs, welding as required greasing and removing unserviceable members, unserviceable CGI/PGI sheets, pully nut and bolts etc., complete all as specified and/or as directed by Engr-in-Charge. |
| 70 | Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface, complete all as specified and/or as directed by Engr-in-Charge. |
| 71 | Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover including PVC insulated unsheathed solid 1.5 sqmm copper conductor cable as continuous earth lead, complete all as specified and/or as directed by Engr-in-Charge. |
| 72 | One light point/fan controlled by one way switch. |
| 73 | One switch socket outlet 6 Amps, 230 volts point on independent board. |
| 74 | One switch socket outlet 6 Amps, 230 volts point on same board. |
| 75 | All as per Srl item No 71 above, but using cables 4 sqmm size. |
| 76 | Supply and replacement of switch piano flush button single pole 6 Amps 230 volts one way, complete all as specified and/or as directed by Engr-in-Charge. |
| 77 | Supply and replacement of switch socket outlet two in one 5 pin 6 Amps flush type 230 volts, complete all as specified and/or as directed by Engr-in-Charge. |
| 78 | Supply and replacement of switch socket combination outlet multi purpose 5 pin 6 Amps and 16 Amps 230 volts, complete all as specified and/or as directed by Engr-in-Charge. |
| 79 | Supply and replacement of ceiling rose, surface bakelite three terminals, complete all as specified and/or as directed by Engr-in-Charge. |
| 80 | S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 volts 12 ways, complete all as specified and/or as directed by Engr-in-Charge. |
| 81 | S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 volts 08 ways, complete all as specified and/or as directed by Engr-in-Charge. |
| 82 | S&F in replacement of MCB SPN 63 Amp 240 Volts AC ISI marked, complete all as specified and/or as directed by Engr-in-Charge. |
| 83 | S&F in replacement of MCB SP 6-32 Amps 240 Volts 50 Hz, complete all as specified and/or as directed by Engr-in-Charge. |
| 84 | S&F only in replacement of LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and/or as directed by Engr-in-Charge. |
| 85 | Taking down old unserviceable high bay light and supply and fix in replacement of LED high bay light fitiing 150 watt 230 Volt AC outdoor type with high pressure die cast aluminium using heat resistant complete with driver, lamp cracket with impact and corosion resistant including thermal management in multiple optics complete with IP65/66 protection at any height as per site condition (including provision of Hydra as per site requirement), complete all as specified and/or as directed by Engr-in-Charge. |
| 86 | Taking down old aviation obstruction lights and supply and fix in repacement of aviation obstruction lights fitting 5.8 watt 230 volt AC outdoor type with aluminium alloy material red in colour lux level is at 1 meter 32 lux operating, temperature -100 to 600 degree celsius with IP65/66 protection to be fixed on top of hanger / bldg of any height, complete all as specified and/or as directed by Engr-in-Charge. |
| 87 | M&L for sub-main wiring with two single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4.00 sqmm 1100 volts grade and including non metallic rigid 25 mm dia PVC conduit caping with all fittings and fixing accessories and including PVC insulated unsheathed, multistranded copper conductor cable of size 4.00 sqmm for earth continuity conductor and including taking down old unserviceable sub main wiring, complete all as specified and/or as directed by Engr-in-Charge. |
| 88 | M&L for sub-main wiring with two single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 10 sqmm 1100 volts grade and including non metallic rigid 25 mm dia PVC casing caping with all fittings and fixing accessories and including PVC insulated unsheathed, multistranded copper conductor cable of size 10 sqmm for earth continuity conductor and including taking down old unserviceable sub main wiring, complete all as specified and/or as directed by Engr-in-Charge. |
| 89 | Taking down old unserviceable industrial plug & socket and supply & fix industrial socket with box for capacity 63 A, 3P+N+E, 415 volts with IP 66 protection, complete all as specified and/or as directed by Engr-in-Charge. |
| 90 | S&F in replacement of exhaust fan, steel body AC single phase 230V of size 300mm sweep with blades, frame and louvers, complete all as specified and/or as directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender