Tender For Repair/Maint To Certain B/R Works At Mes Power House Substation, Chiller Pionts And Other Installation And Certain Bldg In The Aor Of Age B/R Bhdc Under Ge (East) Delhi Cantt-10
Tender Value
45 Lakhs
Estimated cost
Bid Submission
01 Oct 2026
0 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint To Certain B/R Works At Mes Power House Substation, Chiller Pionts And Other Installation And Certain Bldg In The Aor Of Age B/R Bhdc Under Ge (East) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work built in cement mortar including all quoins, pillars etc, complete all as specified and as directed. |
| 2 | M&L brick work with sub class B bricks straight or curved on plan exc 6 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed. |
| 3 | Taking down cement plaster/Grit plaster on brick or stone walls etc. including raking out of joints, hacking for key, scrubbing down with water etc. of any description complete all as specified and as directed. |
| 4 | M&L 15mm thick rendering in cement mortar 1:6 on brick or concrete surfaces of walls, finished the surface fair and even complete all as specified and as directed. |
| 5 | M & L 15 mm thick rendering in cement mortar (1:4), on brick or concrete wall surface, mixed with water proofing compound @ 2% by weight of cement, finished fair & even without using extra cement complete all as specified and as directed. (Note: WPC shall be measured and separately under relevent item of this Schedule). |
| 6 | M & L 10 mm thick rendering in cement mortar (1:3) on ceiling surface, finished even & fair complete all as specified and as directed. |
| 7 | M&L preparation of new plastered wall surfaces and applying two coats of oil bound distemper over and including a coat of alkali resistant primer, and 3 mm thick cement based wall care putty complete all as specified and as directed. |
| 8 | M&L preparation of new plastered wall surfaces and applying two coats of weather proof Exterior emulsion paint of colour & shade as approved (Colour scheme shall be as approved by the GE & user) over and including a coat of exterior primer, and 3 mm thick cement based wall care putty complete all as specified and as directed. Make - Asian Apex Ultima or equivalent of make specified in PS. |
| 9 | M&L preparation of new plastered ceiling and applying two coats of white wash complete all as specified and as directed. |
| 10 | M & L for washed stone grit plaster on exterior walls in two layers, under layers 12 mm thick cement plaster 1:4 (1 cement :4 coarse sand) following the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer with 15 mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand:2 coloured marble stone chipping 10mm nominal size) including using Colour pigment & marble powder as required in ground in panels with groove all around as per approved pattern including scrubbing and washing the top layer with wire brushes and water to expose the stone chippings includind forming groove of uniform size 15mm wide and 15mm deep as per approved pattern complete all as specified and as directed. |
| 11 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed. |
| 12 | M&L 25 mm thick PCC 1:2:4, Type B1, using 20 mm graded stone aggregate, below tiles for levelling of existing surface complete all as specified and as directed. |
| 13 | M&L 7 to 8 mm thick, Non-skid coloured Ceramic tiles, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles, laid over & including 15mm thick screed bed or bedding layer of cement mortar 1:6 as in flooring complete all as specified and as directed. |
| 14 | S&F coloured glazed Vitrified Ceramic tile (Light shade/Double charged/Ultra charged ) 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floors, over 15 mm thick Screed bed in Cement Morter 1:6 for laying floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile complete. |
| 15 | M&L glazed coloured ceramic tiles, 600x300x7mm/450x350x7mm thick, in vertical surfaces such as skirting/ dado etc, set and jointed in cement slurry, laid over & including 10mm thick rendering/ backing coat in cement mortar 1:4, set, jointed and pointed in white cement mixed with colour pigment to match the shade of tile complete all as specified and as directed. |
| 16 | Taking down of chowkhat or frame (without taking off shutter from frame) area not exc 1.50 Sqm each including builder hardware fitting complete all as specified and as directed. |
| 17 | Description all as per item No 16.00 here in Before but area exc 1.50 Sqm & not exc 4.00 Sqm each complete all as specified and as directed. |
| 18 | Taking down shutters of any description area exc 1.00 Sqm but not exc 2.00 Sqm each leaf including builder hardware fitting complete all as specified and as directed. |
| 19 | S&F Mild Steel Framed work as in doors or gates of angle or other section using FE-290 (Gde-E-165) with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 20 | S&F 35 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 21 | S&F solid PVC moulded door frame of size 50x47mm, made out of 5mm thick one side prelaminated and other side plain colour PVC sheet & edges will be painted to match with prelaminated sheet, reinforced with MS square tube fixed with screw/plugs to brick walls complete all as specified and as directed. |
| 22 | S&F Factory made Solid PVC Moulded Door Shutter 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 23 | S&F 100mm size, mild steel butt hinges, cold rolled, medium weight, fixed with Stainless steel screws complete all as specified and as directed. |
| 24 | S&F in repair hydraulic door closer, Alu cast type fixed with aluminium door complete all as specified and directed. |
| 25 | S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed. |
| 26 | S&F 150mm size extruded aluminium alloy handles, cast type anodised complete all as specified and as directed. |
| 27 | S&F 200mm size extruded Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 28 | S&F Powder coated Anodised aluminium doors (sliding/hanging type) with frame size 101.60X44.45X 2.00 mm thick and shutter aluminium anodised and top rail 47.62X 44.45 X 1.50mm and style 47.5 x 44.5 x1.5 mm, lock rail 83.50X 44.45x1.50mm and bottom rail 150.00x44.50x2.50 mm incl necessary aluminium fittings like aluminium butt hinges 04 Nos, aluminium handles 150mm 02 Nos, aluminium tower bolts 200mm 01No, mortice lock 4 lever MS, hydraulic door closer of suitable capacity 01 No, aluminium door stoper 01 Nos, jointing cleats, glazing cleats,rubber packing, anodised aluminium shape beading, screws etc with panelling in two parts with 12mm thick prelaminated partical board in lower panel and 5mm thick tinted glass in upper panels incl all fittings& fixture, complete all as specified and as directed. |
| 29 | Supply, fabricating and fixing windows/Ventilator with frame of aluminium powder coated of extruded aluminium section two track with two sliding shutters with following sections (a) Frame section shall be 63.50 mmx38.10 mmx2 mm thick. (b) Two track bottom rail for sliding of shutters 61.85mm x 31.75mmx2mm thick. (c) Two track top section shall be 61.85mmx31.75mmx2mm thick(d) for sliding shutter handle& 'H' bottom section should be 40mmx(18mm+9)mmx1.45mm thick(e) sliding shutter to be provided with 5.5mm thick sheet glass( Modi/Saint gobain/tinted, plain, frosted (f) stainless steel wire clothes 0.36mm nominal dia of wire and average width of aperature 1.40mm complete all as specified and as directed |
| 30 | S&F 3.0 mm sheet glass, ordinary quality and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 31 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads |
| 32 | S&F in repair stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm, fixed with stainless steel screws complete all as specified and as directed. |
| 33 | Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floor, aprons etc and including disposal of all debris exc 1.5 KMtr not exc 5 Km. |
| 34 | M&L for 100mm PCC type D -2 (1:4:8) using 40 mm graded crushed stone aggregate as in Sub base complete all as specified and directed. |
| 35 | M&L for 50 mm PCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate as in levelling course even and rough complete all as specified and directed. |
| 36 | M&L for 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 37 | M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour in any design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 38 | M&L for chequered cement concrete tiles with grey cement & pigments, size 20cmx20cmx 25 mm thick, set, jointed and pointed in neat cement slurry pigmented to match colour/ shade of tiles as in floors etc.; laid over & including 20 mm thick screed bed or bedding layer in CM 1:6, etc. complete all as specified and directed by Engr-in-Charge. |
| 39 | M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base 15mm thick screed bedding layer in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and filling epoxy grout over it including rubbing and polishing complete all as specified.' |
| 40 | M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick backing coat in CM 1:4 and jointed with pigment to match the shade of the slab including rubbing and polishing complete all as specified |
| 41 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 42 | S&F mild steel rolled sections, Framed work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, using FE-290 (Gde-E-165) complete all as specified and directed. |
| 43 | Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings etc complete all as specified and directed. |
| 44 | S&F in repair, in position Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of approved colour, having tensile strength of 550 MPA as in roof covering/cladding to wall, Chajja etc fixed with self tapping screws as specified, high tensile alloy steel trap sheet having 55 MPA yield strength and zinc (galvanized) + Aluminium combined, coating of 150 GSM /PM2(AZ-150) of 50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDEP polyester of 18 to 20 micron and back coat of 5 to7 micron Epoxy primer fixes, RMR 1040 profile width 1125 mm complete all as specified & as directed. |
| 45 | Description all as per item No 44.00 here in before but plain sheet as in ridge/valley/gutter complete all as specified & as directed. |
| 46 | Dismantling Wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work etc complete all as specified and as directed. |
| 47 | S&F GRG (Glass fibre reinforced Gypsum) semi perforated 12 mm thick tiles of size 595 x 595 mm white colour of approved texture,design (Tegular) and patterns having moisture content less than 2%, humidity ressitance of 99% NRC 0.60 to 0.85 as per IS 8225:1987, Non combustible as per BS 476 Sub Head: 26.0 New Technologies and materials reflectance of 85% (Min) to be laid in true horizontal level suspended on interlocking metal 'T' grid of hot dipped galvanised iron section of 0.33 mm thick (galvanised @ 120grams per sqm including both sides) comprising of main 'T' runners of size 15 x 32 mm of length 3000mm,cross Tof size 15 x 32 mm of length 600mm to form grid module of size 600 x 600mm, suspended from ceiling using galvanised mild steel items(galvanised @ 80 grams per sqm ) i e 50mm long, 8mm outer diameter M-6 dash fasteners,6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x2 mm. Galvanised iron perimeter wall angle of size 24 x 24 x0.40mm thick of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and as directed. (Make- Dimond/ Armstrong/ Gyproc or Shera) Note: Contractor has to submit the drawing to the Engr-in-Charge and get the same approved before execution of GRG work. |
| 48 | M&L false ceiling using powder coated grid system of GI modular grid size 600 x 600 mm with runner 38x24x07 mm cross tee 25x24x0.7 mm and wall angle 24x24x7-8 mm thick PVC laminated Gypsum tiles of size 600 x 600 mm of different designs with rear side MPL film fitted in the grid, grid system hanges by 6 mm dia GI wire to purlin, trusses; RCC slab of the roof etc. with hold down clips, butterfly clips, height fixtures etc, complete all as specified and directed. |
| 49 | S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre (Size of grid 605X605 mm) complete all as specified and directed. |
| 50 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 51 | S&F 4 mm thick Non asbestos fibre cement building boards fixed to GI framework with screws complete all as specified and directed. |
| 52 | M & L in repair 20mm thick Granite slab (of any type) work (table rubbed and polished), in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & half curving the edges of granite stone slab, over and including 20mm thick screed in cement mortar 1:6 including demolition of old stone slab complete all as specified and as directed. |
| 53 | M&L for preparation of new or previously untreated wooden surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paints over and including one coat of pink primer complete all as specified and as directed.. |
| 54 | M&L for preparation of new or previously untreated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paints over and including one coat of red oxide primer complete all as specified and as directed. |
| 55 | M&L for preparation of old wooden surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paints over and including one coat of pink primer complete all as specified and as directed.. |
| 56 | M&L for preparation of old steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paints over and including one coat of red oxide primer complete all as specified and as directed. |
| 57 | M & L for preparation of old decorated wall surface and applying 2mm thick of wall care putty then scrubbing by sand paper to prepare a even surface and applying two coats of OBD of any colour as approved complete all as directed. Please Enable Macros to View BoQ information |
| 58 | M & L for preparation of old decorated wall surface and applying 2mm thick of wall care putty then scrubbing by sand paper to prepare a even surface and applying two coats of OBD of any colour as approved complete all as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender