Tender For Tender For Supply, Installation, Testing And Commissioning Of Audio-Visual System At Auditorium, Ground Floor Of Nabard Head Office
Tender Value
2.60 Crore
Estimated cost
Bid Submission
06 Oct 2026
25 days left
EMD
5.20 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai Suburban → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Tender For Supply, Installation, Testing And Commissioning Of Audio-Visual System At Auditorium, Ground Floor Of Nabard Head Office
BOQ
| Sl. No. | Item Description |
| 1 | AUDIO SYSTEM |
| 2 | Equipment Type: Gooseneck MicrophoneSpecifications:Supplying, installation, testing and commissioning of Gooseneck Microphone as per following specification.Should have minimum length of 15\\" Should be a Condenser microphone and support cardioid polar pattern .Should have XLR / Modular type connector at base Should have Frequency response: Minimum 50 Hz – Maximum 17 kHz or better.Should have Sensitivity: Not less than --40 dBV/Pa (10 mV/Pa) or better.Should have Equivalent self-noise: 28 dB(A) or less.Should support Maximum sound pressure level: 120 dB SPL or more Should have Impedance 170 Ω or less.Should show status indication |
| 3 | Equipment Type: Gooseneck Microphone DocSpecifications:Supplying, installation, testing and commissioning of wired Gooseneck Microphone Base Station for podium as per following specification.Should have table mount for gooseneck mic item under Sr no # 1.01Should have wired mic inputShould have 3- pin XLR connector.Should have mic mute and unmute option from base station. |
| 4 | Equipment Type: Wireless Base TransmitterSpecifications:Supplying, installation, testing and commissioning of the base transmitter for Wireless Gooseneck Microphone as per following specification.Should be capable of being mounting on tableShould be supplied with same OEM lithium-ion rechargeable battery.Should have minimum operating minimum 8 operating hours or moreShould support mute / unmute button.Should supply with necessary accessories.Should be compatible and from the same OEM as Gooseneck Mic under Sr.no # 1.01Should be supplied with compatible Rechargable Batteries. |
| 5 | Equipment Type: Charging StationSpecifications:Supplying, installation, configuration, and commissioning of charging station as per following specification.Should support at least four or more charging slots to simultaneously charge multiple batteries or wireless base transmitters under Sr no # 1.03Should be fully compatible with the rechargeable batteries.Should be supplied with all required power adapters, cables, and connectors necessary for complete operation. |
| 6 | Equipment Type: Wireless Handheld Microphones with ReceiverSpecifications:Supplying, installation, testing and commissioning of the Wireless Handheld Microphone Transmitter and Receiver set as per following specification.Should have cardioid polar patternShould support frequency response of 50 Hz- 15 KHZ or betterShould support sensitivity of Not less than –54 dBV/Pa (2.0 mV/Pa) Should operate over a range of 100 m or more.Should include audio mute functionality.Should be supplied with lithium-ion rechargeable battery that support minimum of 8 hrs continuous operationShould support automatic frequency setup and synchronization Should be supplied with all accessories. Should be supplied with compatible Rechargeable Batteries.(Tenderer should supply 4 Handheld mic with suitable receivers. receiver can be single receiver unit or multiple units to fulfil the requirement) |
| 7 | Equipment Type: Charging StationSpecifications:Supplying, installation, testing and commissioning of the Wireless Handheld Microphone Battery Charging Station as per following specification.Should be Desktop or rack-mountable multi-bay charger suitable for rechargeable batteries.Should support minimum 4 charging slots to simultaneously charge multiple batteries or wireless handheld transmitters Should be fully compatible with the rechargeable batteries used under Sr no #1.05Should be supplied with all required power adapters, cables, and connectors. |
| 8 | Equipment Type: Mic AntennaSpecifications:Supplying, installation, testing and commissioning of the Active Mic Antenna as per following specification.Should be from the same OEM as Wireless Microphone Receiver under Sr.no #1.03Should be active directional, log-periodic antenna designed for use with wireless microphone receiver systems.Should operate over a frequency supporting wireless handheld mic under Sr.no #1.05 and wireless gooseneck base transmitters under S.no #1.03Should include selectable or variable RF gain to compensate for cable loss, with available gain settings up to +10b or moreShould operate power supplied via coaxial cable from the receiver, antenna distributor, or external power supply.Should be suitable for ceiling mounting .Shall be supplied with mounting hardware, power cables, and interconnects as required for complete installation and operation.Should Supply with Antenna Booster and Antenna Splitter.(Tenderer should provide complete solution using Antenna, Antenna Booster and Antenna Splitter to fulfil the requirement) |
| 9 | Equipment Type: Mic Antenna cableSpecifications:Supplying, installation, testing and commissioning of the Antenna Cable as per following specification.Should be compatible with Mic Antenna under Sr.no #1.07Should be of coaxial type with a characteristic impedance of 50 Ω or better, suitable for use with UHF band antenna systems.Should be RG-58 or of superior specification to ensure minimum signal loss and optimal RF performance.Should have low attenuation characteristics and shall be properly shielded to minimize interference and signal degradation over the specified length.Length of cable should min 20 - 25m |
| 10 | Equipment Type: Audio DSPSpecifications:Supplying, installation, testing, and commissioning of a digital signal processor as per following specification.Should have Minimum 16 analog mic/line channels and 8 Output channels onboard or through expander box Inputs shall support +48 V phantom power for condenser microphones.Outputs shall be balanced line-level.Should support AEC on 16 channels hardware-based or available through license from same OEM If AEC is license-activated, the required license(s) must be supplied with the system Should have Integrated USB audio interface or an expander USB box for conferencing applications (Microsoft Teams, Zoom, etc.).Should be of Open-architecture DSP supporting routing, mixing, EQ, dynamics, delay, and logic.Runtime operation shall be license-free once deployed.Should be Rack-mountable |
| 11 | Equipment Type: Column LoudspeakerSpecifications:Should be a professional column array loudspeaker system with controlled vertical coverage and wide horizontal dispersion.Shall consist of multiple high-performance LF and HF drivers to achieve even frequency response and extended bandwidth.Should have Frequency response for low frequency of not more than 95 Hz and high frequency response not less than 15 kHzShould have sensitivity Minimum 85 dB SPL (1 W @ 1 m) or higher.Should be capable of delivering 110 dB SPL peak or higher for full-range reproduction without audible distortion.Should have Horizontal coverage: 100° or betterVertical coverage: Adjustable or beam-steerable; should support mechanical or electronic control to aim sound precisely at the audience area .Should be Slim, column-type enclosure constructed from metal or high-density composite materials Shall include adjustable wall-mount brackets |
| 12 | Equipment Type: Stage monitor Speaker Specifications:Supplying, installation, testing, and commissioning of Stage monitor Speaker as per following specification.Should be 2-way active 12\\" loudspeaker with LF and HF compression driver.Should support minimum 500 W RMS and minimum 1000 W peak or higher capability.Should have frequency response of minimum 40 Hz – 20 kHz or betterShould have minimum 125 dB SPL peakShould have Nominal horizontal dispersion of minimum 95° Should have Vertical dispersion of 40°, with consistent off-axis response.The enclosure shall be of suitable for fixed installation and floor-monitor capability |
| 13 | Equipment Type: Front Fill SpeakerSpecifications:Supplying, installation, testing, and commissioning of Front Fill Speaker as per following specification.Should be a compact two-way passive point-source loudspeaker for fixed installation.Should have Low-frequency transducer: Minimum one 8-inch driver, or multiple drivers having combined equivalent low-frequency driver size not less than 8 inchesShould have High-frequency transducer: compression driver or dome tweeter with constant-directivity horn.Should have Frequency Response of minimum 60 Hz – 20 kHz or better.Should have Nominal Impedance of 8 ohms.Should have minimum 220 W continuous powerShould have Peak Power: upto 500 W.Should support minimum of 115 dB SPL peak valueShould have horizontal coverage angle of minimum 120° .Should have vertical coverage angle of minimum 50° Supplied with mounting hardware and connection accessories necessary for installation on wall |
| 14 | Equipment Type: Delay Speaker Specifications:Supplying, installation, testing, and commissioning of Delay speakers (in ceiling) as per following specification.Should have Low-frequency transducer: minimum 5 inch diameter.Should have Frequency Response of minimum 60 Hz – 20 kHz or better.Should have Nominal Impedance of 8 ohms.Should have minimum 120 W continuous powerShould have Peak Power: up to 300W.Should support minimum of 110 dB SPL peak valueShould have Nominal horizontal coverage of minimum 100° .Should have Nominal vertical coverage minimum 100° Supplied with mounting hardware and connection accessories necessary for installation on wall |
| 15 | Equipment Type: Power AmplifierSpecifications:Supplying, installation, testing, and commissioning of Power Amplifier as per following specification.Should have minimum 4 amplifier channels, each capable of delivering at least 1000 W per channel at 4 Ohm / 8 Ohm / 70V / 100V, and shall be adequately rated to drive the Column Speakers Sr. No.# 1.10 , Subwoofer Sr. No. # 1.16 and Front Fill Speakers Sr.no # 1.12 as specified in the BoQ, whichever power requirement minimum to drive speakers, without compromising system performance.Should be capable of operating in low-impedance (8 Ω) as well as constant-voltage (70 V / 100 V) loudspeaker configurations. Should have Frequency response: 20 Hz–20 kHz Should have THD: ≤0.4%Should have Rack-mount design , forced-air cooling, universal 100–240 V AC.Should include Power supply and accessories for mounting in Rack |
| 16 | Equipment Type: Power AmplifierSpecifications:Supplying, installation, testing, and commissioning of Power Amplifier as per following specification.Should have Channels & Power: Minimum 4 channels, each capable of at least 600 W RMS per channel @ 4 Ohm/8 Ohm / 70V /100 V or shall be adequately rated to drive the Delay Speakers Sr. No.# 13 as specified in the BoQ, whichever power requirement minimum to drive delay speakers, without compromising system performance.Should be capable of operating in low-impedance (8 Ω) as well as constant-voltage (70 V / 100 V) loudspeaker configurations. Should have Frequency response: 20 Hz–20 kHz Should have THD: ≤0.4%Should have Rack-mount design (1U/2U), forced-air cooling, universal 100–240 V AC.Should include Accessories: Power cable, mounting hardware |
| 17 | Equipment Type: SubwooferSpecifications:Supplying, installation, testing, and commissioning of minimum 18inch Subwoofer as per following specification.Should have Frequency Range 40Hz–1kHz or better.Should have Transducer Power : 4000W peak; Max SPL 135dB peak or better. Should have Sensitivity 90 dB or better.Should be Powder coated perforated steel Grille with acoustically transparent black foam backing or better ; Should have nominal impedance of 8 Ohm |
| 18 | Equipment Type: Audio MixerSpecifications:Supplying, installation, testing, and commissioning of Audio Mixer as per following specification.Should Professional analog audio mixer with built-in DSP effectsShould have Minimum 24 input channels (16 Mono Mic/Line + 4 Stereo or better)Should have Low-noise microphone preamps with 48V phantom power for minimm of 10 micsShould have Minimum 3-band EQ on each mono channel with sweep able mid-frequencyShould have Built-in compressor on minimum 8 input channelsShould have Minimum 6 AUX outputs and 4 Group busesShould have Built-in digital effects processor with reverb, delay, chorus, etc.Should have USB interface for audio recording/playbackShould have Frequency response: 20Hz – 20kHzShould have Balanced XLR main outputs and line level outputsSuitable for installed AV applications |
| 19 | VIDEO SYSTEM |
| 20 | Equipment Type: Active LED Videowall Specifications:Supply, Installation, testing and commissioning of Active LED display system as per following specification and Size.Screen 1Should be minimum 148 inch diagonal - (H x 3240 mm + W x 1920mm) - Resolution Support upto 768 x 1296 or better.Should support Portrait and Landscape mode both.Screen 2 Should be minimum 293 inch diagonal - (H x 3240 mm + W x 6720 mm) - Resolution Support upto 2688 x 1296 or better.Screen 3Should be minimum 148 inch diagonal - (H x 3240 mm + W x 1920 mm) - Resolution Support upto 768 x 1296 or better.Should support Portrait and Landscape mode both.General Specification for Active LED Should be suitable for indoor installation, Technology either SMD or MicroLED , with pixel of 2.5 mm.Should have brightness of minimum 600 nits and higher.Should provide wide viewing angles of minimum 150° Horizontal and 150° Vertical or better.Shall include controller / processor supporting up 4K input signals and customer resolution both which is suitable to match diagonal size of LED display.Should be front-serviceable for module and power replacement.Should be suitable for 16 × 7 operation.Should have modules rated lifetime ≥ 100,000 hours.Should have have IP / network-based monitoring and control.Should come with mounting structure / mounting brackets from same or third party compatible OEMShould come with compatible Controller from same or third party OEM with suitable sending & receiving cards to support minimum resolution.Should have control port for control from control processor #4.04Should supply 5% of spare modules of LED wall. |
| 21 | Equipment Type: Active LED StructureSpecifications:Supply, Installation, testing and commissioning of Overall Active LED mounting Structure.The mounting structure shall be fabricated using a combination of Mild Steel (MS) and high-quality engineered wood (BWR/BWP grade plywood or equivalent) to provide adequate strength, rigidity, and finishing.Structure should incorporate a minimum 300 mm high base pedestal from the finished floor level to facilitate installation, maintenance, cable routing, and proper load distribution.The primary load-bearing framework shall be fabricated from MS rectangular/square hollow sections or equivalent structural steel members of suitable thickness, designed based on structural calculations.The steel framework shall be finished with anti-rust treatment, zinc-rich primer, and powder coating or epoxy paint for long-term corrosion protection.A continuous wooden back support panel shall be provided to facilitate secure mounting of the LED cabinets and associated accessories. The wooden panel shall be fixed firmly to the steel framework.The structure shall be designed to maintain proper alignment and flatness of the LED display without visible deformation or vibration.Tenderer Should calculate weight of over all proposed Active LED with 10% buffer weight and design the LED base structure. |
| 22 | Equipment Type: Side DisplaysSpecifications:Supplying, installation, testing, and commissioning of wall Mount Display as per following specification.Should have Screen size: 65\\"diagonalShould have Native Resolution: UHD/4KShould have Brightness: minimum 500 nitsShould support minimum of 16/7 operation hoursShould have Viewing angle: 178 x 178 minimum vertically and horizontallyShould have minimum (02) HDMI input, (01) USB ,(1) Audio Out Should have (01) RJ45 Ethernet LANShould support Landscape Orientation Should have (01) RS232 and (01) RJ45 for control of display from control Processor Sr. no #4.04 |
| 23 | Equipment Type: Swivel Display Wall MountSpecifications:Supplying, installation, testing, and commissioning of Swivel Display Mount as per following specification.Should support screen size of 65\\" Should support VESA mount of upto 600 x 400mmShould support load capacity suitable for the item under Sr.no # 2.03Should support at least 45 degrees swivel opeartionShould be suitable for mounting the Display in Landscape mode |
| 24 | Equipment Type: Front Wall DisplaysSpecifications:Supplying, installation, testing, and commissioning of fixed Wall Mount Display as per following specification.Should have Screen size: 98\\"diagonalShould have Native Resolution: UHD/4KShould have Brightness: minimum 500 nitsShould support minimum of 16/7 operation hoursShould have Viewing angle: 178 x 178 minimum vertically and horizontallyShould have minimum (02) HDMI input, (01) USB, (1) Audio Out Should have (01) RJ45 Ethernet LANShould support Landscape Orientation.Should have (01) RS232 and (01) RJ45 for control of display from control Processor Sr. no # 4.04 |
| 25 | Equipment Type: Fixed wall mount bracket Specifications:Supplying, installation, testing, and commissioning of Fixed Display Wall Mount as per following specification.Should support screen size of 98\\" Should support VESA mount of upto 1000 x 600mmShould support load capacity suitable for the item under Sr.no # 2.05Should support quick and easy installationShould have locking prevents for accidental pop out of mount.Should have safety screws to prevent unauthorised screen removal. |
| 26 | Equipment Type: Digital Signage PlayerSpecifications:Supplying, installation, testing, and commissioning of Digital Signage Player as per following specification.Should support Video Output: HDMI 2.0 supporting up to 4K UHD resolution(3840×2160) @ 60 HzShould support Video Codecs: H.265 (HEVC) and H.264 (AVC)Image Formats: JPEG, PNG, BMP, WebP Should have Network Connectivity: 10/100 Mbps Ethernet (RJ-45)Should support Storage: microSD slot for content.Should come with min 64 GB SD card from same OEM or third party OEM compatible Operation: Fanless, solid-state design for 16 / 7 reliabilityShould support Control Options: Ethernet /USB/GPIO/Serial or equivalentShould support content upload via local network through PC /Laptop without any application. |
| 27 | Equipment Type: Confidence Monitor Specifications:Supplying, installation, testing, and commissioning of Confidence Monitor as per following specification.Should have Screen size: 43\\"diagonalShould have Native Resolution: UHD/4KShould have Brightness: minimum 500 nits.Should support minimum of 16 / 7 operation hoursShould have Viewing angle: 178 x 178 minimum vertically and horizontallyShould have minimum (02) HDMI input, (01) USB, Should have (01) RJ45 Ethernet LAN Should have (01) RS232 and (01) RJ45 ports for control of display from control Processor Sr. no # 4.04 |
| 28 | Equipment Type: Low profile trolleySpecifications:Supplying, installation, testing, and commissioning of Low profile trolley as per following specification.Should be a Low-profile mobile AV equipment trolley suitable for under-display or table placement.Should have Construction of Heavy-duty steel or aluminium frame with durable powder-coated finish.The Design should be Compact, low-height structure for discreet installation (maximum height ≤ 500 mm).Should have wheels and rotating mechanism for rotating display upto minimum of 55 degrees or moreShould support Cable Management with Integrated concealed pathways for signal and power cable routing.Should be suitable for item number Sr no # 2.08 |
| 29 | Equipment Type: PodiumSpecifications:Supplying, installation, testing, and commissioning of Podium as per following specification.Should be constructed from high-quality plywood or MDF with natural veneer or laminated wooden finish, suitable for auditorium use.Should be aesthetically elegant, matching the auditorium interior décor.Should have a slanted top surface for reading or placing notes, along with an edge beading to prevent items from sliding.Should have topp surface with provision to mount two gooseneck microphone (standard XLR female connector type).Should have provision to mount an HDMI transmitter & USB-C Transmitter faceplate under Sr No # 2.11 Should have internal cable routing and concealed wiring channels for audio-visual and electrical connections.Should have a lockable access panel or rear door shall be provided for maintenance and equipment access.Should have include a built-in shelf or compartment for storing AV interfaces, amplifiers, or accessories.The structure shall be rugged and stable, designed for long-term institutional or auditorium use.The finish shall be scratch-resistant, heat-resistant, and stain-resistant, ensuring durability and easy maintenance.The base shall include rubber or nylon feet to avoid floor scratches and provide grip.Dimensions shall be approximately 1100–1200 mm (H) × 600–700 mm (W) × 450–550 mm (D) or as per approved layout.The podium shall be factory-finished and pre-wired, ready for integration with auditorium audio-visual systems.Should have whells at the base for easy movementAll metal parts, if any, shall be powder-coated and rust-resistant.Tenderer need to submit data sheet and Images of podium and prior approval from Consultant and Office in Charge before ordering. |
| 30 | Equipment Type: HDMI & USB-C Transmitter Wall plateSpecifications:Supplying, installation, testing, and commissioning of HDMI & USB-C Transmitter Wall plate as per following specification.Should be 2-input transmitter for digital video and audio extension over twisted-pair cable.Should have 1 × HDMI input Should have 1 × USB-C input supporting DisplayPort Alternate Mode for video and audioShould have Automatic input selection between HDMI and USB-CSupports support video resolutions up to 4K Should be HDCP compliantShould be Full compatibility with HDMI 2.0 standardsShould support Up 4K video transmission upto minimum 40 meter.Should support 1080p transmission upto minimum 70 meter.Shall support Power over Cable (PoC) or Power over HDBaseT (PoH) — powered from compatible receiver under Sr.no # 2.12Suitable for flush or surface mounting either on floor box or in Podium.Should be supplied with mounting hardware and accessories |
| 31 | Equipment Type: HDMI ReceiverSpecifications:Supplying, installation, testing, and commissioning of HDMI Receiver as per following specification.Should be digital AV receiver for HDMI / USB-C signal extension over twisted-pair cable and from same OEM as HDMI & USB-C transmitter faceplate under Sr.no # 2.11Should have 1 × Twisted-pair input (RJ45 or shielded connector) for video, audio, and control signal reception from compatible transmitter # 2.111 × HDMI output supporting video resolutions up to 4KShould be HDCP compliantShould be Full compatibility with HDMI 2.0 standardsShould support Upto 4K video transmission upto minimum 40meter.Should support 1080p transmission upto minimum 70 m Compact, low-profile receiver suitable for tabletop, rack shelf, or behind-display mounting.Supplied with power adapter suitable to provide power to item # Sr No # 2.11 |
| 32 | Equipment Type: HDMI Matrix SwitcherSpecifications:Supplying, installation, testing, and commissioning of HDMI Matrix Switcher as per following specification.Compact, rack-mountable 8×8 HDMI matrix switcher for AV distribution applications.Should have 8 × HDMI inputs, 8 × HDMI outputs Should be Fully non-blocking switching matrix — any input routed to any or all outputs simultaneously.Should Supports resolutions up to 4K @ 60 Hz (4:2:0).Should be HDCP compliant on all inputs and outputs.Should com with HDMI 2.0b standardShould have Selectable audio breakaway / de-embedding to external audio system via analog or addiotnal hardware device.Should have (01) RJ45 ports for control from control Processor Sr. no # 4.04Supplied come with necessary power pack Should support manual operation via integrated front button panel |
| 33 | Equipment Type: Wireless Presentation systemSpecifications:Supplying, installation, testing, and commissioning of Wireless Presentation System as per following specification.Should support 4K output resolutionNative iOS mirroring via Airplay, Windows & Android mirroring via Miracast, as well as Chromebook mirroring.Should have at least 2 nos. of simultaneous user screensSupporting application for IOS, Windows, Android devices to be includedShould provide HDMI out with embedded audio output on HDMI Content encryption to be AES-128 or 1024 bit or WEP 1024Should support presentations through in built WIFI routerShould include Two dongle or connect adaptor (Type C and HDMI) Should include power supply unit & appropriate mounting kit Should have Ethernet (RJ45) for control from control processor Sr. no # 4.04 |
| 34 | Equipment Type: HDMI TransmitterSpecifications:Supplying, installation, testing, and commissioning of Wired HDMI Transmitter as per following specification.Should be Compact, single-input HDMI transmitter for point-to-point extension over twisted-pair cable (HDBaseT or equivalent).Should have 1 × HDMI input and HDCP compliant.Should have 1 × Twisted-pair output (RJ45 or shielded connector) for connection to compatible HDMI receiver under Sr.no # 2.16Supports resolutions up to 4K Should support Upto 4K video transmission upto minimum 40meter.Should support 1080p transmission upto minimum 70 mShould be Powered via PoC / PoH (Power over Cable) from HDMI receiver under Sr.no #B-14, or local 24 V DC power adapter.Supplied come with power adapter & mounting hardware. |
| 35 | Equipment Type: HDMI ReceiverSpecifications:Supplying, installation, testing, and commissioning of HDMI Receiver as per following specification.Should be Compact, single-input HDMI receiver for point-to-point extension over twisted-pair cable (HDBaseT or equivalent).Should have 1 × HDMI output and HDCP compliant.Should have 1 × Twisted-pair output (RJ45 or shielded connector) for connection to compatible HDMI transmitter under Sr.no # 2.15Supports resolutions up to 4K Should support Upto 4K video transmission upto minimum 40meter.Should support 1080p transmission upto minimum 70 supplied come with power adapter & mounting hardware. |
| 36 | Equipment Type: HDMI wall plate receiverSpecifications:Supplying, installation, testing, and commissioning of HDMI wall plate receiver as per following specification.Should be Compact, single-Output HDMI receiver for point-to-point extension over twisted-pair cable (HDBaseT or equivalent).Should have 1 × HDMI output and HDCP compliant.Should have 1 × Twisted-pair inpurt (RJ45 or shielded connector) for connection to compatible HDMI transmitter under Sr.no #2.15Supports resolutions up to 4K Should support Up to 40 m (130 ft) for 4K signals.Should support Up to 70 m (230 ft) for 1080p signals (using CAT6A or higher).Supplied receive power from Compatible transmitter under Sr no # 2.15 |
| 37 | Equipment Type: HDMI Distribution AmplifierSpecifications:Supplying, installation, testing, and commissioning of HDMI Distribution Amplifier as per following specification.Should Have 1x HDMI input.Should have 4x HDMI output.Should support resolution upto 4K60 4:2:0 and HDR signal ready.Should Have EDID management system.Should Have HDCP management system. |
| 38 | CAMERA SYSTEM |
| 39 | Equipment Type: PTZ Camera (Audience View)Specifications:Supplying, installation, testing, and commissioning of PTZ Camera for Audience View as per following specification.Should support 1080p resolutionShould support Minimum Optical Zoom of 30X Should have HDMI Video Outputs Should minimum 20 preset positions Should have control interface of Ethernet or equivalent with necessary convertor (if required ) to control from control processor Sr No # 4.04Should support Image Sensor: Minimum 1/2.8 CMOS Sensor or betterShould have Horizontal field of view of minimum 60 degrees or betterShould come with suitable wall mount from same or third party OEM |
| 40 | Equipment Type: PTZ Camera (Presenter View)Specifications:Supplying, installation, testing, and commissioning of PTZ Camera for Presenter View as per following specification.Should support 1080p resolutionShould support Minimum Optical Zoom of 12X Should have HDMI Video Outputs Should support minimum 20 preset positions Should have control interface of Ethernet or equivalent with necessary convertor (if required ) and control from control processor Sr No # 4.04Should support Image Sensor: Minimum 1/2.8 CMOS Sensor or betterShould have field of view of minimum 70 degrees or betterShould come with suitable ceiling mount from same or third party OEM |
| 41 | Equipment Type: Camera ControllerSpecifications:Supplying, installation, testing, and commissioning of Joystick as per following specification.Should support upto minimum four PTZ CamerasShould have VISCA / ONVIF/PELCO or equivalent protocols with Sr No # 3.01 and 3.02Should have control interfaces via IP and compatible with Sr No # 3.01 and 3.02Should have auto backlight keysShould support PAN / tilt / zoom / focus control to control cameras under Sr No # 3.01 and 3.02 |
| 42 | Equipment Type: Muli viewer & RecorderSpecifications:Supplying, installation, testing, and commissioning of Multiview & Recorder as per following specification. Should support minimum 03 HDMI inputs Should support window layout like PIP , Side by Side window or more layoutShould have internal storage or external storage of up to minimum of 80 GBShould have external storage of recording over FTP/SFTP and Ethernet port for fast transfer of DataShould have HDMI output with embedded audioShould have control over RS232 and Ethernet via control processor under #Sr No 4.04Should be compatible with streaming server installed in premisesShould have Video along with audio outputsShould support recording up to minimum 1080p 60/30 fps |
| 43 | CONTROL SYSTEM |
| 44 | Equipment Type: Wireless Touch PanelSpecifications:Supplying, installation, testing, and commissioning of Wireless Touch Panel as per following specification.Should have Display of Minimum 11-inch multi-touch capacitive display with resolution ≥ 2360 × 1640 pixels.Should have Processor: Minimum A16 Bionic chip or equivalent with Neural Engine.Should have Memory: Minimum 128 GB storage, 6 GB RAM.Should support Connectivity via Dual-band Wi-Fi 6 (2.4 / 5 GHz)Should support Bluetooth 5.2 or higherShould have USB-C port or better for charging and dataShould have Battery Life of Minimum 9 hours continuous operationProvides USB-C interface and anti-slip base.Should come with power adapter Should come with GUI app from control system Sr No # 4.04 |
| 45 | Equipment Type: Docking StationSpecifications:Supplying, installation, testing, and commissioning of Docking Station as per following specification.Should be a Tabletop Dock / Charging Station compatible with Wireless Touch Panel Sr No # 4.01 Should have a Design that provides secure placement and continuous charging of the tablet.Provides USB-C / Lightning charging interface and anti-slip base.Includes power adapter and cable management.Should have Table Enclosure / StandShould have Heavy-duty tabletop mount for permanent or semi-permanent installation.Should Allows tilt adjustment and cable concealment.Should have Aesthetic finish suitable for boardroom / meeting room use. |
| 46 | Equipment Type: Wireless Access PointSpecifications:Supplying, installation, testing, and commissioning of Access Point as per following specification.Wireless Access Point from same OEM as Network Switch item Sr No # 4.05Should have 1G interfaceShould include power supply or POEShould include ceiling mount from same OEM or Custom |
| 47 | Equipment Type: Control ProcessorSpecifications:Supplying, installation, testing, and commissioning of Automation Processor as per following specification.Should have Minimum 8 GB FlashShould support Minimum of 2 GB SDRAM Should have LAN port with industry standard Ethernet communications and Dual NIC supportShould have Built in Web server & licenses/software for wired and wireless touch panel under Should have Minimum (3) RS-232 portsShould have Minimum (4) IR/serial port Should have Minimum (2) Low Voltage relay ports Should have Minimum (4) I/O ports Should include power supply unit & appropriate mounting kit |
| 48 | Equipment Type: Network SwitchSpecifications:Supplying, installation, testing, and commissioning of Network Switch as per following specification.POE Support: Should Support 48 port 300 watts or minimum require to drive all POE based devicesShould have support for 4 x 10GBASE-X SFP+ uplinksShould support multicast, IGMP snooping (V2 & V3), QoS, Jumbo framesShould be able to create separate VLAN for audio, video & controlShould be able to handle Bandwidth requirement for all the connected devicesShould come with necessary Power cable & power supply to be included while quotingShould be compatible & meets the requirement of AVoverIP, Dante, AES67 |
| 49 | Equipment Type: AV RackSpecifications:Supplying, installation, testing, and commissioning of Rack as per following specification.42U equipment rack with front glass door, power distribution box, internal fans, wheels etc. complete with all accessories.Floor standing with castor wheels & locking provision.Fully wired with power distribution and vent to suit forced Air via FanLockable front door made of glass with provision for opening the rack from minimum 4 sidesVented top Cover and bottom covers with cable entry cut-outs.19” angle for rack mounting with provision for recessing mounting angleRemovable side panels with slam latchesFans (Minimum 04 EA.) for cooling of fully populated rackDoor operated CFL light for rackHardware kit including necessary channels for fixing, the supplied equipment inside the rack & bars for cable managementPower Distribution Unit (PDU) with spike guard sufficient enough to supply AC power to all the equipment’s housed inside rack. The PDU should be supplied with industrial universal socket. |
| 50 | Equipment Type: Floor BoxSpecifications:Supplying, installation, testing, and commissioning of Floor Box as per following specification.Floor Box should be of Type: Recessed floor box for AV and power connectivity.Should have Construction of Heavy-duty metal body with stainless-steel or brushed aluminium cover.Should have Lid with Flip-open type with cable exit slot and soft-close mechanism.Should have Configuration of 2 × Power sockets (230 V AC, 6/16 A) , 3 × Data (RJ-45) ports for Transmitter and receiver & 2 x XLR(audio) portsElectrical sockets should of Universal type, ISI-approved, shutter-protected.Data ports should be Suitable for Cat-6A termination.Should have XLR ports: 3-pin female connectors for balanced audio.Should include complete accessories with back box, faceplate, and fixing screws.Compliance: Conforms to relevant electrical and safety standards |
| 51 | Equipment Type: Capture CardSpecifications:Supplying, installation, testing, and commissioning of Capture Card as per following specification.Should have HDMI input and USB 3.0 OutputShould support min 1080p resolutionShould come with necessary power supply and accessories |
| 52 | Installation Equipment |
| 53 | Equipment Type: HDMI CablesSpecifications:Supplying, installation, testing, and commissioning of min 3ft HDMI Cable as per following specification.Should Support 4K60 resolutionShould Support Color Sampling 4:2:0 or higher HDMI Type-A connector (male), gold plated |
| 54 | Equipment Type: HDMI CablesSpecifications:Supplying, installation, testing, and commissioning of min 6ft HDMI Cable as per following specification.Should Support 4K60 resolutionShould Support Color Sampling 4:2:0 or higher HDMI Type-A connector (male), gold plated |
| 55 | Equipment Type: HDMI CablesSpecifications:Supplying, installation, testing, and commissioning of min 25ft HDMI Cable as per following specification.Should Support 4K60 resolutionShould Support Color Sampling 4:2:0 or higher HDMI Type-A connector (male), gold plated |
| 56 | Equipment Type: USB CablesSpecifications:Supplying, installation, testing, and commissioning of 6 ft USB-C patch cable (USB-C Male to USB-C Male). as per following specification.Should support USB Type-C to USB Type C Male to Female Cable Should be USB 3.2 type and supports data transfer rate up to - 10 GBbpsCable should features high quality Shielded Twisted Pair (STP) constructionLength: 6 feet. |
| 57 | Equipment Type: USB CablesSpecifications:Supplying, installation, testing, and commissioning of 6 ft USB-A patch cable (USB-A Male to USB-B Male). as per following specification.Should support USB Type-A to USB Type B Male to Female Cable Should be USB 3.2 type and supports data transfer rate up to - 10 GBbpsCable should features high quality Shielded Twisted Pair (STP) constructionLength: 6 feet. |
| 58 | Equipment Type: USB CablesSpecifications:Supplying, installation, testing, and commissioning of 6 ft USB-A patch cable (USB-A Male to USB-B Male). as per following specification.Should support USB Type-A to USB Type B Male to Female Cable Should be USB 2.0 type and supports data transfer rate up to - 10 GBbpsCable should features high quality Shielded Twisted Pair (STP) constructionLength: 6 feet. |
| 59 | Equipment Type: USB CablesSpecifications:Supplying, installation, testing, and commissioning of 6 ft USB-C patch cable (USB-A Male to USB-C Male). as per following specification.Should support USB Type-A to USB Type C Male to Female Cable Should be USB 3.2 type and supports data transfer rate up to - 10 GBbpsCable should features high quality Shielded Twisted Pair (STP) constructionLength: 6 feet. |
| 60 | Equipment Type: Speaker CableSpecifications:Supplying, installation, testing, and commissioning of Speaker Cable (2.5 sq.mm)2 core 2.5 sq. Mm/ 14 AWG PVC insulated copper conduction loudspeaker cable |
| 61 | Equipment Type: Audio/Control CableSpecifications:Supplying, installation, testing, and commissioning of Control and Microphone/Audio Cable as per following specification.Single shielded twisted pair, 20 AWG, tinned copper conductorsNon plenum 2 core PVC insulated copper conduction microphone cable |
| 62 | Equipment Type: CAT6 cableSpecifications:Supplying, installation, testing, and commissioning of STP/ CAT-6 Cable as per following specification.Cable shall be optimized for use in digital video over twisted pair application |
| 63 | Equipment Type: Cables & Connectors |
| 64 | Non AV Material |
| 65 | Equipment Type: Conduit Specifications:Supply Installtion, testing and commissioning of fixing of conduit as per the location mentioned on ceiling/wall as per tender drawings and under supervision of project engineerShould be approved quality PVC.Should be minimum 25mm in diameter.Should be free from Cracks, Bends and defect. Tenderer to visit site and consider lumpsum cost of over all conduiting work of Auditorium |
| 66 | Equipment Type: Raceway Specifications:Supply Installation, testing and commissioning of laying of Raceway as per the location mentioned in the tender drawings and under supervision of project engineerShould be corrosion resistant material.Should be minimum 100mm in dimension. Tenderer to visit site and consider lumpsum cost of over all raceway work of Auditorium |
| 67 | Equipment Type: Electrical Cable Specifications:Supply Installation, testing and commissioning of Electrical cable and power points as per the location given in tender drawings and under supervision of project engineer. Tenderer to visit site and considered electrical cable and power as per suggestion from proposed Active LED OEM.Tenderer can use 1.5 sq mm electrical cable or better for AV hardware equipment's |
| 68 | Equipment Type: Electrical Power Plug PointsSpecifications:Supply Installation, testing and commissioning of Electrical 6 amp or better power socket with switch.Should be India Standard.Location of power socket as per tender document.Tenderer to visit site and provide power socket count and should use 1.5 sq mm cable for standard AV power and 16amp for Rack power and should be Indian type 6amp and 16amp. |
| 69 | Equipment Type: Interior Civil Work Specifications:Supply Installation, testing and commissioning of Civil interior work as per the guideline given in tender document and site visit.Tenderer should visit the site and quote civil work cost as per site condition. |
| 70 | Lighting System |
| 71 | Equipment Type: LED Parcan lightSpecifications:Supply, installation, testing and commissioning of LED Light Fixture suitable for professional lighting applications as per following specifcation.Should Have High-quality LED Light SourceShould have minimum 100W LED Light.Should have Colour warn white temperature of minimum 3000K.Should have Colour Rendering Index of ≥ 95Should have Power Cable 3 Core Copper PVC Insulated CableShould be compatable with DMX Channel ModeShould have Beam Angle Adjustable and Selectable Beam AngleShould have Smooth dimming from 0 - 100 electronic. |
| 72 | Equipment Type: LED BLINDER LIGHTSpecifications:Supplying, Installation, Testing & Commissioning of Professional LED Wash Effect Light with all required accessories, as per following specifications:Should have Minimum 3 × 100W LED sourceShould have Color Temperature of minimum 3200K.Should have Color Rendering of ≥ 95Should have Power Input of 230V AC.Should have Beam Angle of minimum 40°Should Illuminate minimum 8,000 Lux at 2 meters distance with specified beam angleShould have Smooth dimming from 0 - 100 electronic. |
| 73 | Equipment Type: 54 x 3W PAR RGBW LIGHTSpecifications:Supply, installation, testing and commissioning of RGB LED Light suitable for professional stage applications as per following specification.Should have LED RGBW light sourceShould have Multiple RGBW LED lights arrangement for uniform colour .Should consumption minimum 100W of power.Should have colour mixing system of RGBW (Red, Green, Blue & White) colour mixingShould have minimum of 230V AC power using 3 core copper cable.Should be compatable with DMX channel mode and support minimum 8 DMX channels.Should have Beam Angle of minimum 15° |
| 74 | Equipment Type: LED 200W PROFILE LIGHTSpecifications:Supplying, Installation, Testing & Commissioning of 200W LED Spot Light for professional stage applications as per the following specification.Should have high Power Single COB LED SourceShould provie 200W LED power.Shoul d have color temperature of mimimum 3000K to 3200K.Should have color rendering index (CRI) miminum 90 Should have minimum of 230V AC power using 3 core copper cable.Should be compatable with DMX channel mode and support minimum 3 DMX channels.Should have Smooth dimming from 0 - 100 electronic.Should provide approx 20,000 lux at distnace of minimum 2 meter. |
| 75 | Equipment Type: 54 x 3W PAR 3200K LIGHTSpecifications:Supply, installation, teting and commissioning of 120W professional stage application as per following specification.Should have high efficiency LED light source with multiple individual LED with warm white light.Should have color temperature of minimum 3000 k with warm white output.Should have color rendering Index (CRI) mimimnum 90.Should have minimum of 230V AC power using 3 core copper cable.Should be compatable with DMX channel mode and support minimum 1 DMX channels.Should have Beam Angle of minimum 15° with narrow beamShould provide minimum 7,000 lux at distnace of minimum 2 meter.Should have Smooth dimming from 0 - 100 electronic. |
| 76 | Equipment Type: LED MOVING HEAD LIGHTSpecifications:Supplying, installation, testing and commissioning of 150W LED Moving Head Light for stage application as per following specifcation.Should have high power LED source minimum 150W Cool White LEDShould support power consumption minimum 150W.Should have minimum of 230V AC power using 3 core copper cable.Should have Beam Angle of minimum 2°Should be suitable for long throw applications usig high intensity output.Should be compatable with DMX channel mode and support minimum 2 DMX channels.Should have motorized colour wheel with minimum 14 colours plus open position or betterShould have Gobo System, gobo wheel with minimum 14 gobos plus open position or betterShould have motorized rotating prism system with multi-facet prism effect (8/16 facet or equivalent)Should have Smooth dimming from 0 - 100 electronic. |
| 77 | Equipment Type: C-CLAMPSpecifications:Supply, installation, testing and commissioning of C Shape clamps for stage application as per following specifcation.Should have MS material threaded Galvanized lock key,Should have plastic glass filled nylon moulded M6 key.Should have receptacle minimum 28mm standard TV spigot.Should have safety MS galvanized chain with pin. |
| 78 | Equipment Type: Safety BondSpecifications:Supplying, installation, testing, and commissioning of Safety bond with lock as per following application.Should have 1.5 meter long clip 1.5 Mtr Long.Should have twisted pair of GI wire rope, with minimum 2mm / 3mm Thickness with sleeve to be fixed around the grid to avoid fall of the material in case if the \\"C\\" clamp is not locked properly. Should take load of minimum 150Kgs. |
| 79 | Equipment Type: Identification Name PlateSpecifications:Supplying, installation, testing, and commissioning of 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish. |
| 80 | Equipment Type: FIXED STAGE LIGHT BARSpecifications:Supplying, installation, testing, and commissioning of Light bar of 10 meters with lock as per following specifcation.Should be made using MS materisl, 40NB class B pipe with dual barrel construction.Should be treated with chemical to keep them rust free.Should have minimum 40x75x40 cable trenching arrangement.Should have dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength(Tenderer to visit site and take correct measurement as per the site condition and select light bar based on selected OEM) |
| 81 | Equipment Type: FIXED FOH LIGHTING BARSpecifications:Supplying, installation, testing, and commissioning of Fixed FOH Light Bar, as per following specifcation.Should have minimum 14 meters of length.with 101 degree curve.Shoul dbe MS40NB Class B pipe with dual barrel Should be treated with chemical to keep them rust free.Should have minimum 40x75x40 cable trenching arrangement.Should have dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength(Tenderer to visit site and take correct measurement as per the site condition and select light bar based on selected OEM) |
| 82 | Equipment Type: LIGHTING JUNCTION BOXSpecifications:Supplying, installation, testing, and commissioning of Junction box, as per following specifcation.Should be MS material fabrication.Should have 4 way 10A, 250v AC connection.Should be box type made up of 22SWG for LED lighting fixture with pipe clamp.Junction box should be from same OEM as lights as under Sr no# 7.01 to 7.10 |
| 83 | Equipment Type: SPLITTER & CONSOL JUNCTION BOXSpecifications:Supplying, installation, testing, and commissioning of consol Junction box, as per following specifcation. Should be MS material fabrication.Should have 4 way 10A, 250v AC connection.Should have option to put rocker switch to power up splitter and console.Consol junction box should be from same OEM as lights as under Sr no# 7.01 to 7.10 |
| 84 | Equipment Type: DMX Signal IN Junction BoxSpecifications:Supplying, installation, testing, and commissioning of MS Fabricated 5 pin DMX Signal IN Junction box as per following specifcation.Should have option of 5 pin DMX female socket.Should be 22 SWG CRCA material. Should have pipe clamp and grid arrangement for fixing for wall/floor.Should have black polyester powder coated.junction box should be from same OEM as lights as under Sr no# 7.01 to 7.10 |
| 85 | Equipment Type: DMX Signal OUT Junction BoxSpecifications:Supplying, installation, testing, and commissioning of MS Fabricated 5 pin DMX Signal Out Junction box as per following specifcation.Should have option of 5 pin DMX female socket.Should be 22 SWG CRCA material. Should have pipe clamp and grid arrangement for fixing for wall/floor.Should have black polyester powder coated.Junction box should be from same OEM as lights as under Sr no# 7.01 to 7.10 |
| 86 | Equipment Type: DMX Signal Loop Junction BoxSpecifications:Supplying, installation, testing, and commissioning of MS Fabricated 5 pin DMX Signal loop Junction box as per following specifcation.Should have option of 5 pin DMX female socket.Should be 22 SWG CRCA material. Should have pipe clamp and grid arrangement for fixing for wall/floor.Should have black polyester powder coated.Junction box should be from same OEM as lights as under Sr no# 7.01 to 7.10 |
| 87 | Equipment Type: Power Distribution BoxSpecifications:Supplying, installation, testing, and commissioning of Lighting Distribution Board as per following specifcation.Should be CRCA material.Should be chemically treated to keep rust free.Should be powder coated with Matt texture finish consists of R, Y, B Indicator lamp, for the junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing Distribution box should be from same OEM as lights as under Sr no# 7.01 to 7.10 |
| 88 | Equipment Type: Auxiliary Marshalling BoxSpecifications:Supplying, installation, testing, and commissioning of 100W LED Light as per following specifcation.Should have single COB light source.Should have colour temperature of minimum 3000K Should have color rendering Index (CRI) mimimnum 90.Should have minimum of 230V AC power using 3 core copper cable.Should be compatable with DMX channel mode and support minimum 5 DMX channels.Should have Beam Angle of minimum 11°Should provide minimum 30,200 lux at distnace of minimum 2 meter.Should have Smooth dimming from 0 - 100 electronic. |
| 89 | Equipment Type: SPLITTER Specifications:Supplying, installation, testing, and commissioning of DMX splitter asper following specifcation.Should have minimum one 5 Pin DMX In socket Should have 8 Nos 5 Pin DMX Out socketShould have In and out signal.Should have LED Indicator for check the signal flow in output.Should be standard 19” cabinetShould be black epoxy polyester powder coated texture finish. |
| 90 | Equipment Type: CONSOLESpecifications:Supplying, installation, testing, and commissioning of Digital Lighting Console.Should be from same OEM as light fixure.Should have minimum 1000 DMX channel.Should have LCD Screen for easy navigation.Should be DMX xompatible.Should be capable of control upto 96 moving LED lights and other LED lights.Should have multi functional faders. |
| 91 | Equipment Type: XLR MALE/FEMALE CONNECTORSSpecifications:Supplying, installation, testing, and commissioning of 5 Pin XLR Termination plug Should made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resister with 0.25Watt for signal termination. |
| 92 | Equipment Type: XLR TEMINATION PLUGSpecifications:Supplying, installation, testing, and commissioning of 5 Pin XLR Termination plug Should made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resister with 0.25Watt for signal termination. |
| 93 | Equipment Type: POWER CABLESpecifications:Supplying, installation, testing, and commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm. |
| 94 | Equipment Type: DMX SIGNAL CABLESpecifications:Supplying, installation, testing, and commissioning of DMX Signal 2 OR 4 core + Ground shielding Cable with CE mark for the Signal network. |
| 95 | Equipment Type: Cable RacewaysSpecifications: Supplying, installation, testing, and commissioning of MS perforated tray as per following specifcation.Should be minimum Size 40 x 75 x 40mm & 1.6 mm.Should undergone through 7 tank process with various chemical treatment to keep them rust free, Shoud be epoxy polyester powder coated with Matt black texture finish along with clamping arrangement. |
| 96 | Equipment Type: InternalEarthingSpecifications:Supplying, installation, testing, and commissioning of Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under our scope. |
| 97 | Providing Comprehensive Annual maintenance Contract and provision of Resident Engineers at NABARD Head Office as per terms and conditions specificied in the tender |
| 98 | CAMC ChargesComprehensive AMC for 4 years from the completion of Defect Liability Period as per terms and condition of Tender4th Year (1% of Total SITC Charges) - will be auto-populated by taking into account the cost quoted in sections - 1 to 7 above |
| 99 | CAMC ChargesComprehensive AMC for 4 years from the completion of Defect Liability Period as per terms and condition of Tender5th Year (3% of Total SITC Charges) - will be auto-populated by taking into account the cost quoted in sections - 1 to 7 above |
| 100 | CAMC ChargesComprehensive AMC for 4 years from the completion of Defect Liability Period as per terms and condition of Tender6th Year (5% of Total SITC Charges) - will be auto-populated by taking into account the cost quoted in sections - 1 to 7 above |
| 101 | CAMC ChargesComprehensive AMC for 4 years from the completion of Defect Liability Period as per terms and condition of Tender7th Year (5% of Total SITC Charges) - will be auto-populated by taking into account the cost quoted in sections - 1 to 7 above |
| 102 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 1st YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) |
| 103 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 2nd YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) |
| 104 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 3rd YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) |
| 105 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 4th YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) |
| 106 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 5th YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) |
| 107 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 6th YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) |
| 108 | One OperatorVisit per Day on Call basic for duration of 7 years ( 3 years DLP + 4 years) Per Day charge for 7th YearShould be minimum technical qualification for AV nd Lighting,Should have minimum of 2 years of experience of working as AV Engineer with sound knowledge of AV devices.Should be available 4hr or before the event and check entire system in advance.Suould be able to rectify the problem and make system workable. Should be available for entire event throuout a day and operate AV devices as per requirement of NABARD.. In case if required the resource should be available on weekends or national holidays.(Tenderer to provide per day visit charges of operator) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender