Tender For 1) Repair And Maintenance Of Road From Kurseong Bye-Pass Towards Phusdhura Village (L=3.00 Km), 2) Repair And Maintenance Of P.B. Road From Kurseong Railway Station Upto Chandmari Fatak Dara (L=1.80 Km), 3) Thorough Repair And Maintenance Of Ti
Tender Value
10.76 Crore
Estimated cost
Bid Submission
19 Sep 2026
5 days left
EMD
21.53 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Darjeeling → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For 1) Repair And Maintenance Of Road From Kurseong Bye-Pass Towards Phusdhura Village (L=3.00 Km), 2) Repair And Maintenance Of P.B. Road From Kurseong Railway Station Upto Chandmari Fatak Dara (L=1.80 Km), 3) Thorough Repair And Maintenance Of Tindharia-Chunnabhatti Road (L=2.70 Km), 4) Thorough Repair And Maintenance Of Road From Dilaram To Bagora (L=2.50 Km), 5) Thorough Repair And Maintenance Of Road From Ambootia Godown Dhura Upto Baseri Village (L=2.20 Km), 6) Repair And Maintenance Of Road From Sebjay Gaon To Tribal Gaon, Sittong Iii (L=2.45 Km), 7) Repair And Maintenance Of Road From Kurseong Bye-Pass Road Towards Munsidhura Village, Karbia (500 M), 8) Repair And Maintenance Of Road From Thamdara To Rai Gaon (L=1.20 Km), 9) Repair And Maintenance Of Mercy Chowk To Gandhi Gram Village, Latpanchar (L=700M), 10) Repair And Maintenance Of The Connecting Lane Road From Gyanjyoti More Towards Pintail Village, Dagapur, Matigara Block, Gta, 11) Annual Maintenance Of Road Under The Jurisdiction Of The Division Accept For The Roads Listed Above ( Sl. No 1 To 10)
BOQ
| Sl. No. | Item Description |
| 1 | Repair and Maintenance of Road from Kurseong Bye-Pass towards Phusdhura Village (L=3.00 Km) |
| 2 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 3 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 4 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 5 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 6 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).i)On bituminous surface @ 0.20kg- 0.3kg /sqm. |
| 7 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 8 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 9 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 10 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 11 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 12 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 13 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 14 | Repair and Maintenance of P.B. Road from Kurseong Railway Station upto Chandmari Fatak Dara (L=1.80 Km) |
| 15 | Repairing Pot-holes with Bituminous Macadam (Grading - I, for compacted thickness of 80mm to 100mm)Filling Pot Holes with Bituminous Macadam using Mobile Hot Mix plant (6-10 TPH) with approved crushed aggregates of specified grading premixed with bituminous binder @3.3% by wt. of the total mix, transported to site and laid in the pot hole prepared before hand by cutting the edges to get a firm vertical face and by removing all the failed and loose materials including dust and applying tack coat evenly on the sides and on the surface as per specification, rolling the filled depression with 8- 10 tonne smooth wheeled roller to achieve the desired compaction, including the cost and carriage of stone aggregates and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of all operational staff, quality control except the cost of tack coat complete as per direction of Engineer-incharge.Payment to be made on the basis of the loose net volume of the stone aggregates used in the work. |
| 16 | Providing and laying 25 mm thick mastic asphalt wearing course with approved grade bitumen meeting the requirements given in table 500-39, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated fine-grained hard stone chipping of 13.2 mm nominal size at the rate of 0.005cum per 10 sqmand at an approximate spacing of 10 cm center to center in bothdirections, pressed into surface when the temperature of surfacesis not less than 100°C, protruding 1 mm to 4 mm over mastic surface, all complete as per clause 516 (Reference to MORT&H's specification clause 516 along with IRC:107). |
| 17 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).i)On bituminous surface @ 0.20kg- 0.3kg /sqm. |
| 18 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 19 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 20 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 21 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 22 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 23 | Thorough Repair and Maintenance of Tindharia-Chunnabhatti Road (L=2.70 Km) |
| 24 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 25 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 26 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 27 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 28 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).i)On bituminous surface @ 0.20kg- 0.3kg /sqm. |
| 29 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 30 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 31 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 32 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 33 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 34 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 35 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 36 | Thorough Repair and Maintenance of road from Dilaram to Bagora (L=2.50 Km) |
| 37 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 38 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 39 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 40 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 41 | Bituminous MacadamProviding and laying bituminous macadam with 100-120 TPH hot mix plant using crushed aggregates of specified grading premixed with approved bituminous binder @ 3.3% (min) for Grading -1 and 3.4% (min) for Grading -2 by weight of total mix , transported to site, laid over a previously prepared base with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction (Reference to MORT&H's specification clause 504).(i) for Grading I ( 40 mm nominal maximum aggregate size ) Layer Thickness 80-100mm |
| 42 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 43 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 44 | PCC 1:3:6 in FoundationPlain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days (Reference to MORT&H's specification 2100). |
| 45 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 46 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 47 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 48 | Retro-Reflectorised Traffic Signs:Providing and fixing of retroreflectorised cautionary, mandatory andinformatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick,when signs with maximum side dimensions do not exceed 600mm, or with aluminium sheeting 2.0mm thick when signs with maximum side dimensions exceeds 600mm, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801).60 cm equilateral triangle |
| 49 | Retro-Reflectorised Traffic Signs:Providing and fixing of retroreflectorised cautionary, mandatory andinformatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick,when signs with maximum side dimensions do not exceed 600mm, or with aluminium sheeting 2.0mm thick when signs with maximum side dimensions exceeds 600mm, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801).60 cm circular |
| 50 | Road Marking with Hot Applied Thermoplastic Compound withReflectorising Glass Beads on Bituminous SurfaceProviding and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes (Reference to MORT&H's specification 803). |
| 51 | Supplying & fixing of Raised Pavement Markers/Road Studs/Cats Eye made of polycarbonate moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 13635 kg tested in accordance to ASTM D 4280 Type H and compling to Specifications of Category A of MoR&TH Circular No. RW/NH/33023/10-97 - DO III Dt. 11.06.1997 & MoRT&H's specification for Road &Bridge Works (Fifth Rev.). Marker height shall not be less than 10 mm and shall not exceed 20 mm, width shall not exceed 130mm and with minimum reflective area of 13 sqcm on each side and slope to the base shall be 35 ± 5 degree. Fixing will be without nails but by using epoxy resin based adhesive as per manufacturer's recommendation including site clearence etc and complete as directed by the Engineer in Charge.The contractor will have to provide a test certificate from a reputablenational/international laboratory comforming the above specifications. |
| 52 | Thorough Repair and Maintenance of Road from Ambootia Godown Dhura upto Baseri Village (L=2.20 Km) |
| 53 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 54 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 55 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 56 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 57 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).i)On bituminous surface @ 0.20kg- 0.3kg /sqm. |
| 58 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 59 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 60 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 61 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 62 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 63 | Gabian Structure for Retaining Earth RIVER TRAINING & PROTECTION WORKS Providing and construction of a gabian structure for retaining earth with segments of wire crates of size 7 m x 3 m x 0.6 m ( 7.50m x 3.0m x0.6m ) each divided into 1.5 m compartments by cross netting, made from 4 mm galvanised steel wire @ 32 kg per 10 sqm having minimum tensile strength of 300 Mpa ( tensile strength 300-450 Mpa ) conforming to IS:280 and galvanizing coating conforming to IS:4826, woven into mesh with double twist, mesh size not exceeding 100 x 100 mm, filled with boulders with least dimension of 200 mm, all loose ends to be tied with 4 mm galvanised steel wire (Reference to MORT&H's specification 2503.3). |
| 64 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 65 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 66 | Repair and Maintenance of Road from Sebjay Gaon to Tribal Gaon, Sittong III (L=2.45 Km) |
| 67 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 68 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 69 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 70 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 71 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 72 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 73 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 74 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 75 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 76 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 77 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 78 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 79 | Hill Side Drain Clearance Removal of earth from the choked hill side drain and disposing it on the valley side manually as per the requirement of MORT&H's specification cl.3000. |
| 80 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 81 | Repair and Maintenance of Road from Kurseong Bye-Pass Road towards Munsidhura Village, Karbia (500 m) |
| 82 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 83 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 84 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 85 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 86 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 87 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 88 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 89 | Dry Rubble Flooring Construction of dry rubble flooring (shall be laid closely on the prepared base in one or more layers with appropriate bond) at cross drainage works for relatively less important works (Reference to MORT&H's specification 2506). |
| 90 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 91 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 92 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 93 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 94 | Repair and Maintenance of Road from Thamdara to Rai Gaon (L=1.20 Km) |
| 95 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 96 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 97 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 98 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 99 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 100 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 101 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 102 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 103 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 104 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 105 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 106 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 107 | Hill Side Drain Clearance Removal of earth from the choked hill side drain and disposing it on the valley side manually as per the requirement of MORT&H's specification cl.3000. |
| 108 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 109 | Repair and Maintenance of Mercy Chowk to Gandhi Gram Village, Latpanchar (L=700m) |
| 110 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 111 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 112 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 113 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 114 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 115 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 116 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 117 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 118 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 119 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200). |
| 120 | Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Granular material |
| 121 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 122 | Hill Side Drain Clearance Removal of earth from the choked hill side drain and disposing it on the valley side manually as per the requirement of MORT&H's specification cl.3000. |
| 123 | Retro-Reflectorised Traffic Signs:Providing and fixing of retroreflectorised cautionary, mandatory andinformatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick,when signs with maximum side dimensions do not exceed 600mm, or with aluminium sheeting 2.0mm thick when signs with maximum side dimensions exceeds 600mm, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801).60 cm equilateral triangle |
| 124 | Retro-Reflectorised Traffic Signs:Providing and fixing of retroreflectorised cautionary, mandatory andinformatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick,when signs with maximum side dimensions do not exceed 600mm, or with aluminium sheeting 2.0mm thick when signs with maximum side dimensions exceeds 600mm, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801).60 cm circular |
| 125 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 126 | Repair and Maintenance of the Connecting Lane Road from Gyanjyoti More towards Pintail Village, Dagapur, Matigara Block, GTA. |
| 127 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 128 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 129 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 130 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 131 | Bituminous MacadamProviding and laying bituminous macadam with 100-120 TPH hot mix plant using crushed aggregates of specified grading premixed with approved bituminous binder @ 3.3% (min) for Grading -1 and 3.4% (min) for Grading -2 by weight of total mix , transported to site, laid over a previously prepared base with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction (Reference to MORT&H's specification clause 504).(ii) for Grading II (19 mm nominal maximum aggregate size) Layer Thickness 50-75mm |
| 132 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 133 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work(Reference to MoRT&H's specification clause 304).Ordinary soilManual Means (Depth upto 3 m) |
| 134 | PCC 1:3:6 in FoundationPlain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days (Reference to MORT&H's specification 2100). |
| 135 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 136 | Dry Rubble Flooring Construction of dry rubble flooring (shall be laid closely on the prepared base in one or more layers with appropriate bond) at cross drainage works for relatively less important works (Reference to MORT&H's specification 2506). |
| 137 | Annual Maintenance of Road under the jurisdiction of the division accept for the roads listed above ( Sl. No 1 to 10) |
| 138 | Clearing Grass and Removal of Rubbish: By Manual MeansClearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area. (Reference to MoRT&H's specification clause 201) |
| 139 | Hill Side Drain Clearance Removal of earth from the choked hill side drain and disposing it on the valley side manually as per the requirement of MORT&H's specification cl.3000. |
| 140 | By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401Rate per cum for grading-III Material |
| 141 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 142 | Repairing Pot-holes with Bituminous Macadam (Grading - I, for compacted thickness of 80mm to 100mm)Filling Pot Holes with Bituminous Macadam using Mobile Hot Mix plant (6-10 TPH) with approved crushed aggregates of specified grading premixed with bituminous binder @3.3% by wt. of the total mix, transported to site and laid in the pot hole prepared before hand by cutting the edges to get a firm vertical face and by removing all the failed and loose materials including dust and applying tack coat evenly on the sides and on the surface as per specification, rolling the filled depression with 8- 10 tonne smooth wheeled roller to achieve the desired compaction, including the cost and carriage of stone aggregates and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of all operational staff, quality control except the cost of tack coat complete as per direction of Engineer-incharge.Payment to be made on the basis of the loose net volume of the stone aggregates used in the work. |
| 143 | Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer usingmechanical means (Reference to MORT&H's specification clause502). On WMM/WBM surface @ 0.70-1.0kg /sqm. |
| 144 | Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii)On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 145 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Case - I: Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 146 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Case - II : Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 147 | PLUM CONCRETE (1:3:6)Plain cement concrete of nominal mix (1:3:6 ) with coarse aggregate of which stone boulder of size 225 mm to 150mm of 60% of total dry volume to be placed in position as directed by Eng-in charge ,67% - 40 mm down single &33% - 20 mm down bazri , Coarse Sand ,Cement ( 53 grade ) mechanically mixed in 1:3:6 of rest volume and placed in position and compacted by any means as directed including cost of shuttering . |
| 148 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M15 |
| 149 | Add 18% GST Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysSep 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender