Tender For Periodical Services To Certain Otm Accn North Side And South Side Of Runway In Tech Area At Bhisiana Under Ge (Af) Bhisiana
Tender Value
25 Lakhs
Estimated cost
Bid Submission
03 Oct 2026
15 days left
EMD
50000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Periodical Services To Certain Otm Accn North Side And South Side Of Runway In Tech Area At Bhisiana Under Ge (Af) Bhisiana
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster/rough cast plaster from brick walls/soffits of roof projections & chajjas /ceilings etc. including racking out joints, hacking for key & scrubbing down with water etc including disposal of rubbish material to any distance out side MOD land complete all as specified and as directed. |
| 2 | Material and labour for 15mm thick cement plastering/ rendering in cement mortar (1:4) on any face of Brick walls or concrete surfaces, finished even and fair complete all as specified and as directed. |
| 3 | Material and labour for rendering/plastering 10-12 mm thick in CM (1:6) on any face of Brick walls or concrete surfaces, finished even and fair complete all as specified and as directed. |
| 4 | Material and labour for rendering/plastering 5 mm thick in CM (1:3) on concrete surfaces of ceiling, finished fair and even complete all as specified and as directed. |
| 5 | Supply and fixing chicken wire mesh ( Murga jali ) in cement plaster or over joints of RCC and brickwork or as per site requirement of 24 gauge & 10-13 mm mesh, width as required for construction joints, plastering work at joints wall & RCC, and chasing in brick work for electrical conduits or water supply pipes, including pegs/nails, binding wire as required for fixing/supporting arrangement before rendering / plastering etc. as per site requirement complete all as specified and as directed.Note: Rendering / plastering shall be measured and paid separately under respective item of BOQ |
| 6 | Material and labour for preparation of old treated surfaces (plastered / unplastered) of walls/pillars /cornices by remove / scraping down all loose treatment etc with using broom, wire brush or by any other mean and after preparing the surfaces applying one coat of white wash by using paint brush complete all as specified and as directed. |
| 7 | Material and labour for preparation of new plastered surfaces of ceiling by brooming down or by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash by using paint brush complete all as specified and as directed. |
| 8 | Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down or by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash by using paint brush complete all as specified and as directed. |
| 9 | Material and labour for preparation of old plastered surfaces of walls/pillars /cornices by brooming down or by sand papering or by any other mean and after preparing the surfaces applying two coats of white wash by using paint brush complete all as specified and as directed. |
| 10 | Material and labour for preparation of old plastered surfaces of ceiling by brooming down or by sand papering or by any other mean and after preparing the surfaces applying two coats of white wash by using paint brush complete all as specified and as directed. |
| 11 | Material and labour for preparation of existing treated surface of walls/pillars /cornices etc. by removing/scraping all loose paint, treatment, dust, dirt and other foreign matter using broom, paint brush, sand paper, wall sander or any other suitable means as required. The item includes filling of nail holes, pin holes and hairline cracks with approved putty wherever required and prepared to obtain a smooth and even finish. Thereafter, applying one coat of Oil Bound Distemper (OBD) of approved make and shade as per surface condition matching the existing, applying by using paint brush or roller brush complete all as specified and as directed. |
| 12 | Material and labour for preparation of existing treated surface of ceiling by removing/scraping all loose paint, treatment, dust, dirt and other foreign matter using broom, paint brush, sand paper, wall sander or any other suitable means as required. The item includes filling of nail holes, pin holes and hairline cracks with approved putty wherever required and prepared to obtain a smooth and even finish. Thereafter, applying one coat of Oil Bound Distemper (OBD) of approved make and shade as per surface condition matching the existing, applying by using paint brush or roller brush complete all as specified and as directed. |
| 13 | Material and labour for preparation of existing treated surface of ceiling by removing/scraping all loose paint, treatment, dust, dirt and other foreign matter using broom, paint brush, sand paper, wall sander or any other suitable means as required. The item includes filling of nail holes, pin holes and hairline cracks with approved putty wherever required and prepared to obtain a smooth and even finish. Thereafter, applying two coats of Oil Bound Distemper (OBD) of approved make and shade as per surface condition matching the existing, applying by using paint brush or roller brush complete all as specified and as directed. |
| 14 | Material and labour for preparing the surface and applying two coats of Oil Bound Distemper (OBD) of approved make and shade to walls/pillars /cornices surfaces (over any type of surface new or old prepared after complete removal etc.) over one coat of cement primer suitable for OBD, paint and primer applying by using paint brush or roller brush complete all as specified and as directed. |
| 15 | Material and labour for preparing the surface and applying two coats of Oil Bound Distemper (OBD) of approved make and shade to ceiling surfaces (over any type of surface new or old prepared after complete removal etc.) over one coat of cement primer suitable for OBD, paint and primer applying by using paint brush or roller brush complete all as specified and as directed. |
| 16 | Material and labour for complete removal of existing treatment of any type/description (any layer) from external/internal wall/ceiling surfaces, soffits/chajja/roof projection surfaces etc., by scraping steel patti and Mechanical sander/grinder machine having suction vaccum Bag (Smart periodical methodology), complete all as specified and as directed. |
| 17 | Material and labour for preparation of interior surfaces of walls/ceiling/soffits etc (over any type of surface new or old prepared after complete removal etc), applying acrylic putty is a water-based, Smooth, creamy paste (ready-to-use), white or off-white color (thickness from 1.0 to 1.5 mm as required for desired smoothness and levelling of surfaces in two layers), including sanding with wall sander after filling the putty in first coat/second coat to make surface smooth and ready for receiving further painting work complete all as specified and as directed.Notes : (i) The prepared surface after putty, the contractor will inform to the Engineer-in-Charge/GE for site inspection before applying further finishes. Further finishes work will start only after approval of the prepared surface from the Engineer-in-Charge through site order. |
| 18 | Material and labour for preparation of old previously treated surfaces of concrete / kerb stone or similar surface of any description not otherwise described over 10cm width or girth, by cleaning the dust and removing all loose particle with using clean cloths, brooms and dry paint brush etc and after preparing the surfaces applying two coat of synthetic enamel paint (1st quality) of approved tint/colour (one colour or alternative any colour black/white/yellow etc) complete all as specified and as directed. |
| 19 | Material and labour for preparation of old/new surfaces of concrete, hardstanding, chequered tiles, interlocking tiles or any other similar floor surface, irrespective of width or girth, by thoroughly cleaning the surface and removing dust, dirt and all loose particles by wire brushing, sweeping with brooms, air blowing, washing wherever required, etc., including removal of grass/vegetation along edges and disposal of all debris from site. After proper preparation of the surface, applying three coats, comprising one priming coat and two finishing coats, of approved all-weather floor protector paint, water-based and PU enriched, in approved colour(s), having high adhesion and high abrasion resistance properties, GreenPro certified, free from added Lead, Mercury and Chromium, with VOC content less than 100 g/L and complying with applicable GS-11 eco-standard requirements, having gloss level of 20–25 at 60° on glass plate when tested/applied at 300 micron DFT by box coater, complete all as specified and as directed by the Engineer-in-Charge.Notes : (i) One priming coat shall be applied by diluting the paint with water @ 500 ml water per litre of emulsion, followed by two finishing coats, each diluted with water @ 100–150 ml per litre of emulsion, or strictly as recommended by the manufacturer's technical data sheet/brochure. Coverage of primer and finishing paint shall be as per the manufacturer's approved technical literature/brochure.(ii) A minimum interval of 2 to 3 hours, or such longer duration as recommended by the manufacturer depending upon site/weather conditions, shall be maintained between successive coats to ensure proper drying, curing and adhesion of the complete paint system.Make: Berger – Weather Coat Floor Protector / Asian Paints – Apex Floor Guard / Nippon Paint – Pro Floor (WB), or equivalent approved make by GE. |
| 20 | Material and labour for Providing and applying two or more coats of textured paint/surface coating of approved make and shade over walls and other surfaces, after preparing the surface with a coat of water-based primer and 2–4 mm thick plaster of Paris (POP) running in strips/patches as required to provide a smooth and even surface, including all necessary surface preparation, making good imperfections and application of textured paint/surface coating to achieve the approved texture and finish, complete all as specified and as directed by the Engineer-in-Charge. |
| 21 | Material and labour for providing square/rectangular cement-plastered plates of required size at buildings, for writing/displaying building numbers, identification marks or other information, by applying 15 mm thick cement plaster/rendering in cement mortar (1:4) on any face of brick masonry walls or concrete surfaces, including preparation of new/existing surfaces, cleaning and removal of dust, dirt and loose particles, wetting, hacking/raking of concrete surfaces wherever necessary for proper bond, forming and finishing the plates to the required size and shape, finishing the plastered surface smooth, even and fair to receive lettering/painting, complete all as specified and as directed by the Engineer-in-Charge. |
| 22 | Material and labour for Obliterating old writing of any description, not exceeding 0.1 sq. m, with synthetic enamel paint to match existing work, complete all as specified and as directed by the Engineer-in-Charge. |
| 23 | Material and labour for marking Stops, commas, short lines, dashes, hyphens, brackets, etc. of size compatible with existing letters or figures with synthetic enamel paint complete all as specified and as directed. |
| 24 | Material and labour for Writing letters or figures with synthetic enamel paint (Block. Roman, Italic or Indian) not exceeding 30 cm high etc complete all as specified and as directed. |
| 25 | Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to matching with the existing, with using paint brush complete all as specified and as directed. |
| 26 | Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying two coats of synthetic enamel paint (1st quality) of approved tint/colour to matching with the existing, with using paint brush complete all as specified and as directed. |
| 27 | Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to matching with the existing, with using paint brush complete all as specified and as directed. |
| 28 | Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying two coats of synthetic enamel paint (1st quality) of approved tint/colour to matching with the existing, with using paint brush complete all as specified and as directed. |
| 29 | Material and labour for preparation of old steel and iron surfaces of any description, not otherwise described, not exceeding 10 cm in width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to matching with the existing, with using paint brush complete all as specified and as directed. |
| 30 | Material and labour for preparation of old painted wooden surfaces of any description, width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one or more coats of French polish complete all as specified and as directed by Engineer-in-Charge. |
| 31 | Material and labour for preparation of new surface of walls / Soffits of Chajjas / Roof Projections etc. by removing all loose dust/dirt using broom and applying two coats of premium quality water-based exterior emulsion paint based on 100% acrylic binder with silicone additives, having VOC content not exceeding 50 g/litre when tested in accordance with IS 101 (Part 2/Sec 2) and UV resistance conforming to IS 15489:2004 or latest revision, of approved brand and manufacture, in camouflage pattern using 4 to 5 approved colour shades as per pattern approved by the Engineer-in-Charge or match with adjoining surface. The paint shall have a coverage capacity of approximately 6.5 to 7.5 square metres per litre for two coats and shall be applied over one coat of alkali-resistant water-based exterior primer of the same make having a coverage capacity of approximately 11 to 14 square metres per litre per coat, the paint shall be applied by brush, roller or airless spray gun as directed by the Engineer-in-Charge, complete in all respects as specified and directed by the Engineer-in-Charge.Brand and Make of primer for external : - Seal O Primer of Berger / Smart Care Primero of Asian / Excel Alkali Prime of Nerolac / Weather Shield Alkali Bloc of DuluxBrand and Make of exterior acrylic emulsion paint: - Apex Ultima of Asian / Weather Coat antidust of Berger / Weather shield Protect of Dulux / Excel Mica Marble of NerolacNotes : (i) A minimum interval of 4 to 6 hours, or such duration as recommended by the manufacturer, shall be maintained between successive coats to ensure proper drying, curing and adhesion of the paint system. |
| 32 | Note For the all BOQ item(s) : Wherever the work is required to be executed at any height of the building, structure or hangar and/or at scattered locations, the quoted unit rate shall be deemed to be inclusive of all costs towards labour, materials, tools, plant, equipment, incidental arrangements, shifting and handling of materials, access arrangements and all other resources necessary for complete execution of the work at the required height(s) and locations, including provision of scaffolding, staging, working platforms, ladders, hoisting arrangements, safety equipment, protective measures and compliance with all applicable safety requirements, rules and regulations. No extra payment whatsoever shall be admissible on account of execution of the work at height or for any of the above arrangements. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysOct 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender