Tender For Maintenance Of Special Armed Force Office Building By Plastering In Inside & Outside, Woodwork In Doors & Windows , Painting Inside And Outside Including Water Supply Pipe & Sanitary Fittings Etc. At A.D.Nagar, Agartala
Tender Value
Ref. Documents
Estimated cost
Bid Submission
07 Oct 2026
23 days left
EMD
19500
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Maintenance Of Special Armed Force Office Building By Plastering In Inside & Outside, Woodwork In Doors & Windows , Painting Inside And Outside Including Water Supply Pipe & Sanitary Fittings Etc. At A.D.Nagar, Agartala
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing The surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc. complete as per direction of the Engineer-in – charge |
| 2 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-in – charge. 25 mm average thickness |
| 3 | Dismantling W.C. Pen of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in – charge |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level : 1:2:4( 1 Cement : 2 fine sand :4 graded well burnt brick aggregate 20 mm nominal size) |
| 5 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-in – charge. Bars upto 12 mm diameter |
| 6 | Providing & fixing super lates-302(SBR based) water proofing expert (Dr. Fixit ) over R.C.C slab with 3(three) component by mixing super latex, water & cement at 1:4:7 or as per Manufacturer recommendation in/c cleaning the roof surface with wire brushed & with cleaned water before application & curing the chemicals by sprinkling water for 3-5 days after application of water proofing components complete as per direction of the Eng-in charge and technical recommendation of the manufacturer |
| 7 | Providing, mixing and applying SBR polymer (of approved make0 modified Cement mortar in proportion of 1:4( 1 cement: 4 fine sand with polymer minimum 2% by wt. Of cement used) as per specifications and as per direction of the Engineer-in-charge. 25 mm average thickness in 2 layers |
| 8 | Providing and applying cement slurry on old CC/RCC/Brick works in joints to receive new and fresh CC/RCC/Brick works including roughening and cleaning the old surface as required complete as per direction of the Engineer in charge |
| 9 | 12mm ement plaster of mix (i) Cement mortar 1:4(1 cement : 4 fine sand) |
| 10 | Taking out doors, windows and clerestory window shutters (Steel or wood) including stacking within 50 metres lead : of area 3 sqm and below |
| 11 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : (i) Of area 3 sqm and below |
| 12 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : (i) Local Teak Wood |
| 13 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 X 12 mm for fixing panelling and or glazing as per direction of Engineer- In-Charge. (i) Local take Wood (a) 35 mm thick shutters |
| 14 | Providing and fixing panelling or panelling and glazing in panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for peneled or panelled and glazed shutters 25 to 40 mm thick. (i) Local Teak Wood 16 mm thick |
| 15 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:- In grating, frames, guard bar, railing, brackets, gates and similar works, all complete |
| 16 | Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diamerer bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 17 | Providing and fixing factory made UPVC door frame made of UPVC extrude, section having an overall dimension, as below (tolerance +/- 02mm corners of the door frame to be joined with galvanized brackets and stainless screws, joint mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 x 19mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge, (i) Extruded section Profile size 48 x 40 mm |
| 18 | 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59 x 24 mm and wall thickness 2 mm = 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised MS tube of size 20 x20 mm and 1 mm + 0.1 mm wall thickness, The lock rail made up of “H” Section, a UPVC hollow section of size 100 x 24 mm and 2 mm + 0.2 mm wall thickness fixed to the shutter styles by means of plastic/ galvanised MS “U” cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and I mm + 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-In Charge,(for W.C. and Bathroom door shutter) |
| 19 | 6 mm cement plaster of mix : (i) Cement mortar 1:3 (1 cement : 3 fine sand) |
| 20 | 12 mm cement plaster of mix in/c. Neat cement punning (i) Cement mortar 1:4 (1 cement : 4 fine sand) |
| 21 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 22 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. (i) For thickness of tiles 10 mm to 25 mm |
| 23 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC cement less than 50 grams/ litre, of approved brand and manufacture to give an even shade (Payment shall be made after submission of Test Certificate issued by the Manufacturer) : New work (two or more coats) over and including water thibbable priming cost with cement primer |
| 24 | Distempering with 1st quality washable acrylic distemper of approved brand and manufacture and of required complete as per direction of the Engineer in charge |
| 25 | Providing and laying App ( Atactic polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen @ 0.40 litre/sqm by the same membrane manufactured of density at 25’C, 0.87 – 0.89 kg/litre and viscosity 70 – 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23’C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction ad 60/80N. Softening point of membrane not less than 150’C. Cold flexibility shall be upto- 2’C when tested in accordance with ASTM, D – 5147 as per direction of the Engineer-in-Charge. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane as required as per direction of the Engineer-in-charge. (i) 3 mm thick |
| 26 | Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture (Payment shall be made after submission of Test Certificate issued by the Manufactured) : New work ( two or more coats applied @ 1.43 litre /10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 27 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge |
| 28 | Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shad including preparation of surface as required complete as per direction of the Engineer in charge |
| 29 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade (payment shall be made after submission of Test Certificate is issued by the Manufacturer); Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 30 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS; 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawing and the direction of Engineer- in- charge. (Glazing and panelling and dash fasteners to be paid for separately) :- (a) For fixed portion of approved quality :- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) |
| 31 | (b) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately : :- Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) |
| 32 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber/neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (cost of snap beading shall be paid in basic item):- With float glass panes of 4.0 mm thickness (weight not less than 10.0 kg/sqm) |
| 33 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300 x 16 mm |
| 34 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 150 x 10 mm |
| 35 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm |
| 36 | Cutting holes upto 30 x 30 cm in walls including making good the same : (i) With 1 st class bricks |
| 37 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion : (i) Single socketed pipe- 110 mm OD |
| 38 | Single socketed pipe -75 mm OD |
| 39 | Providing and fixing on wall face unplasticised – PVC moulded fittings / accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Coupler (i) 110 mm |
| 40 | Bend 87.5’ (i) 110 mm |
| 41 | Bend 87.5’ (i) 110 mm |
| 42 | Providing and fixing unplasticised polyvinyl Chloride (UPVC) pipes including all UPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per the direction of Engineer-in charge. (a) Internal & outer work. Exposed on wall. (a) 25mm nominal outer dia. Pipes. 20mm nominal outer dia. Pipes |
| 43 | 25 mm nominal outer dia. Pipes |
| 44 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cist3ern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 45 | Providing & fitting fixing of C.P brass hand spray (Royal made ) as per direction of the Eng. In charge |
| 46 | Providing & fitting of C.P brass Twin one stop cock (Royal made) complete as per direction of the Engg. In charge |
| 47 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931(i) 15 mm nominal bore |
| 48 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. (i) White Vitreous china Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass pillar tap |
| 49 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350mm and 340x410x365mm sizes respectively |
| 50 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622- 2017 (thickness to be specified by the manufacturer0 of approved make in all colours, shades of any size as approved by Engineer-in charge in skirting, risers of steps and dados, laid over 12mm thick bed of cement mortar 1 :3 (1 cement : 3 fine send) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in charge. 9i) 450 mm x 300 mm in all shades and design |
| 51 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 – 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20mm thick cement mortar 1:4 (1 cement :4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. (a) Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles (i) 300 mm x 300 mm in all shades and designs |
| 52 | Providing and fixing ball valve (brass0 of approved quality High or low pressure, with plastic floats complete : (i) 25 mm nominal bore Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 23 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender