Tender For special repair To Radiology Deparment In 12Th Floor New Opd Block Igmc Shimla. ( Sh-: Demoltion Work, Aluminum Work, Granite Work , Ws & Si Etc.)
Tender Value
Ref. Documents
Estimated cost
Bid Submission
17 Sep 2026
1 days left
EMD
12610
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Shimla → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special repair To Radiology Deparment In 12Th Floor New Opd Block Igmc Shimla. ( Sh-: Demoltion Work, Aluminum Work, Granite Work , Ws & Si Etc.)
BOQ
| Sl. No. | Item Description |
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)including carriage of materials within all leads and lifts. |
| 2 | Demolition of brick work above G.L. upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within all leads and lifts. In cement mortar. |
| 3 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50metres lead;- For thickness of tiles 10mm to 25mm complete including carriage of materials within all leads and lifts. |
| 4 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 5 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron |
| 6 | Providing and fixing ACP sheet 3mm thick in aluminium ceiling/lining/partitions with PVC neoprens gasket fixed with self drilling screws etc. complete as per Architect drawings and by the Engineer-in-Charge including carriage of materials within all leads and lifts. (Cost of aluminium snap beading shall be paid in basic item). |
| 7 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.Pre-laminated particle board with decorative lamination on both sides |
| 8 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. (Only weight of grill to be measured for payment). |
| 9 | Providing and Fixing Wire Mesh 144 G of approved brand & quality in windows & doors including carriage of materials within all leads and lifts. |
| 10 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 250x16 mm |
| 11 | providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 250x10 mm |
| 12 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :100 mm |
| 13 | Providing and fixing 18mm thick gang saw cut, mirror polished, prem ulded and prerulished, machine cut for kitchen platforms, vity counters, ndow sills, facius and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment. epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels(i) Granite stone |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Vertical memebers |
| 15 | Providing Tor steel reinforcement for reinforced cement concrete work including bending binding and placing in position and cost of binding wire complete up to all floor levels/all heights.as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation within all leads, lifts and other incidential charges. |
| 16 | Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : Columns, pillars, posts and struts Square, rectangular or polygonal in plan. |
| 17 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) |
| 18 | 15mm (Fifteen milimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) within all leads, lifts of materials and other incidentals. |
| 19 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 20 | Providing and laying Vitrified tiles in any size (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc.600mmx600mm. |
| 21 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid |
| 22 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireWhite Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 23 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings |
| 24 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 25 | Providing and fixing PVC waste pipe for sink or washbasin including P.V.C. waste fittings complete |
| 26 | Providing and fixing 100 mm sand cast iron/ steel grating for floor trap |
| 27 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. Brass screws and complete |
| 28 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 18.49.1 15 mm nominal bore |
| 29 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 18.53.1 15mm nominal bore |
| 30 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge |
| 31 | Providing and fixing .PVC. connection pipe with brass union including carriage of materials within all leads and lifts :-300/450mm length :-15mm nominal bore. |
| 32 | Providing & fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor 15mm nominal bore |
| 33 | Providing and fixing G.I union 15mm including carriage of materials within all leads and lifts. |
| 34 | Providing and fixing high pressure PVC (finolex) Type-A spigot and socket, waste and ventilating pipes ISI marked with collar and clamps including fixing with approved adhesive etc. complete. including carriage of materials within all leads and lifts :-110mm nominal size |
| 35 | Providing and fixing PVC (finolex )110 mm dia Plain bends ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts. |
| 36 | Providing and fixing PVC (Finolex) 45 degree bend 110mm dia ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts. |
| 37 | Providing and fixing 110mm X 75mm size PVC Finolex type \\"A\\" floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials within all leads an lifts. |
| 38 | Providing and fixing 110 mm dia PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete including carriage of materials within all leads an lifts. |
| 39 | Providing and fixing 110 mm dia PVC collars ISI marked including fixing with approved adhesive etc.complete including carriage of materials within all leads an lifts. |
| 40 | Providing and fixing 19mm thick commercial board in shelves/box for cup board with butt joints and fixing with nails and screws etc. complete including carriage of materials in all leads and lifts. |
| 41 | Providing and fixing 19mm thick Commercial Board shutters for Cup boards i/c fixing with nickel plated piano hinges with screws etc complete including carriage of materials in all leads and lifts. |
| 42 | Providing and fixing 0.80 mm thick coloured or plain laminated sheet (sunmica) on boards / ply wood sheets with approved adhesive and nails complete including carriage of material in all leads and lifts. |
| 43 | Providing and fixing 1.00 mm thick coloured or plain laminated sheet (sunmica) on boards / ply wood sheets with approved adhesive and nails complete including carriage of material in all leads and lifts. |
| 44 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete including carriage of materials within all leads and lifts:- Double strip (horizontal type). |
| 45 | Providing fastener for fixing cupbord in wall including carriage of materials within all leads and lifts |
| 46 | Providing and fixing 75mm size special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete including carriage of materials in all leads and lifts. |
| 47 | Providing and fixing ISI marked steel handles conforming to with necessary screws etc. complete :(i) 150mm |
| 48 | Providing edge moulding to 20 mm thick Kota stone counters, Vanities etc including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer |
| 49 | Providing and fixing CP Brass Single lever wall mixer of quality & make as approved by Engineer in charge. ) 15 mm nominal dia |
| 50 | Providing and fixing one hole basin mixing Faucet. including carriage of materials within all leads and lifts. |
| 51 | Providing and fixing Acrylic shelf including carriage of materials within all leads and lifts. |
| 52 | Providing and fixing Towel Rail including carriage of materials within all leads and lifts. |
| 53 | Providing and fixing Towel Ring including carriage of materials within all leads and lifts. |
| 54 | Providing and fixing Soap holder with Acralic Dish including carriage of materials within all leads and lifts. |
| 55 | Providing and fixing UPVC door window shutter wuthframe including shutter made of UPVC extruded section of size approved byengineer in charge with wall thickness 2.00mm corners of door frame to be mitred cut and joints with plastic brackets and stainless steel screws etc with 6mm thick toughed glass approved width 5mm complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 daySep 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender