Tender for Tender for The Work Of Wall Painting, Matting, And Installing Furniture In The Library Of Government Primary School 6 Ggm (Primary Section) By Gram Panchayat Gogameri
Tender Value
8.66 Lakhs
Estimated cost
Bid Submission
15 Sep 2026
4 days left
EMD
17324
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hanumangarh → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for The Work Of Wall Painting, Matting, And Installing Furniture In The Library Of Government Primary School 6 Ggm (Primary Section) By Gram Panchayat Gogameri
BOQ
| Sl. No. | Item Description |
| 1 | Providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS 2095- Part I at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceilingsection 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel withconnecting clips made out of 2.64mm diax230mm |
| 2 | PVC WALL PANAELLING |
| 3 | FLOOR MATE WORK |
| 4 | LIGHT FITTING AND WIRE ,PANALLIGHT and other accessirios ETC (Pennal Light) |
| 5 | लाईट पॉइन्ट/फेन पॉईन्ट/ एक्जास्ट फेन पॉइन्ट/ काल बेल पॉईन्ट के लिए 1.5 वर्ग मि.मी. एफआर पीवीसी इन्सुलेटेड कॉपर कन्डक्टर सिंगल कोर केबिल से, मॉडयूलर स्विच, मॉडयूलर प्लेट, उपयुक्त जीआई बॉक्स एवं 1.5 वर्ग मि.मी. एफआर पीवीसी इन्सुलेटेड कॉपर कन्डक्टर सिंगल कोर केबिल से अर्थिग सहित आवश्यकतानुसार सतह/खाली स्थान में मध्यम दर्जे की पीवीसी कन्डूट वाईरिंग करना |
| 6 | Roof FAN AND FIXING |
| 7 | Inverter with Double batterycomplete wiring fitting |
| 8 | Provindin and fixing Wifi box |
| 9 | Enamal paint on new surface |
| 10 | window jali |
| 11 | Provinding and fixing table seat table size with ply board thick 22 mm with sunmica inner size 2.25 *2 feet height from floor 2.5 to 3 feet with all neccesary |
| 12 | Steel pipe pedded chair |
| 13 | lhesaV IykLVj nhokj ij 1%6 vuqikr es lhesaV&ctjh feykdj dj tksMksa dks dqjsnus rFkk14 fnu rd fu;fer rjkbZ lesr |
| 14 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth includingnecessary repairs to scratches by sandla/loi. (only for colour changing ). |
| 15 | Providing & applying wall putty (JK/Birla orequivalent) or POP filling complete to achieve fine finish (one or more coats) (asper PWD BSR) |
| 16 | Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect.Add extra if Apex , Royal or other equivalent exterior paint usedinstead of plastic emulsion (as per PWD BSR) |
| 17 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with requiredPVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately).Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) |
| 18 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS :12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixedin aluminium doors , windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-chargePre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 19 | Demolishing mud phuska/ Lime dhar/ Kharanja in terracing and disposal of unserviceable material within 50 meters lead. |
| 20 | Providing and Applying ACRYLIC emulsion polymer waterproofing chemical coating, on over roof on over roofslabs/terrace/balconies/parapet wall method/specification: etc.with following Paint the surface with regular paint brush so as to obtain approximately 0.3mm thickness coating. apply the 2nd coat next day at right angles to the 1st coat so that total thickness of the coating should be approximately 0.6mm coverage by using above formulation will be 40 ft2/ litre of chemical. painted surface does not require any external water curing since chemical will hold sufficient water for curing.After the primer coat Apply 2 coats of modified acrylic emulsion polymer water proofing compound having solar heat reductionproperties coating @ 0.330 KG/SQM on the surface of the interval of 3-4 hours. Undulation on the surface is repair before the waterproofing work. |
| 21 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc.with PVS / neoprene gasket etc. complete as per the architectural drawings and thedirections of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.)With glass panes of 4.0 mm thickness (weight not less than 10.0 kg/sqm) as per IS : 2835. |
| 22 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steelmembers shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Grade 304 |
| 23 | सफेद रंग के चमकीली चाईना मिट्टी की टाईलों की आपूर्ति करना तथा प्लास्तर के ऊपर सीमेंट स्लरी से लगाना तथा जोड़ों में सफेद सीमेंट लगाना ( प्लास्टर की कीमत शामिल नहीं है)। |
| 24 | LIGHT OR OTHER ACCESSORIES |
| 25 | STAFF TABLE |
| 26 | अधिरचना में प्रथम श्रेणी की ईन्टो की चिनाई सिमेन्ट बजरी 1:6 मसाले में मय बगल की झिर्री बन्द करने तथा तराई समेत। |
| 27 | Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). |
| 28 | सूचना फलक Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysSep 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender