Tender For Special Repair To Airmen Mess (P-459) At Air Force Station Carnicobar. 8846/E8
Tender Value
45 Lakhs
Estimated cost
Bid Submission
30 Sep 2026
17 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nicobar → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Airmen Mess (P-459) At Air Force Station Carnicobar. 8846/E8
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tilling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 2 | Material and Labour for vitrified ceramic tiles 8-10 mm thick polished area of each tiles not exceeding 0.36 sqm of any shade and any pattern (pattern consists combination of two or more tiles ) as in floor etc jointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 15mm thick screed bed in CM 1:6 and pointed in coloured cement to match coloured tiles complete complete all as specified and as directed. . Note:- (i) The colour, shade and pattern shall be approved by the GE during execution work. (ii) No extra cost shall be allowed for Removing and refixing and necesary cutting of door etc if any required during execution of work. |
| 3 | Material and labour for glazed ceramic coloured tiles in vertical surface 450x350x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10mm thick backing coat in CM 1:4 complete complete all as specified and as directed. |
| 4 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid and bedded and pointed in any mortar all as specified and as directed. |
| 5 | Material and labour for 20-25mm thick machine cut kota stone slabflooring laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and machine polishing, laid over and including 20mm thick screed in CM 1:6 in floors complete all as specified and as directed. all as specified and as directed. |
| 6 | Material and Labour for Granite 20mm thick ( of any type table rubbed and polished) work machine cut as in steps, jambs pillars,window cills, cooking platforms and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of granite and laid over and including 15mm thick cement mortar 1 :4 complete all as specified and directed. |
| 7 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 8 | Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 40 x 40 x 2mm, cross Tee of size 40 x 40 x 2mm and wall angle of size 40 x 40 x 2mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls complete all as specifed and as directed including provision of with 4mm thick Non Asbestos boards, ordinary type for fixing in 600 mm x 600mm grid, fixed in ceiling, flat or sloping, complete all as specified and directed.Note :- Rate quoted above shall be deemed to include for making holes, cutting chassis if any required and making good to existing walls in cement mortar 1: 3 to match with existing surface finish as directed at site. |
| 9 | Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (without taking off shutters from the frame) complete all as specified and directed. |
| 10 | Material and labour taking down chowkhats or frames, without taking off shutters from the frame not exceeding 1.5 Sqm in each and removing complete all as specified and directed. |
| 11 | Supply and fix Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.Note : Glass panel/particle board panel filling shall be measured and paid separately. |
| 12 | Supply and fix powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, and sliding tower bolt 150mm long anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 13 | Supply and fix for powder coated, Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. |
| 14 | Supply and fix Powder Coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum coating of grade AC 15) of DG 102 design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved aluminium standard section around the opening, all complete as per requirement complete all as specified and directed. |
| 15 | Supply and fixing aluminium alloy,anodised, sliding door bolt of length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed. |
| 16 | Supply and Fix 150mm long aluminium anodised barrel tower bolt all as specified and as directed by Eng-in-charge. |
| 17 | Supply and fix Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with Aluminium alloy wire staples complete all as specified and directed |
| 18 | S&F aluminium (Die cast body) Door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters 701 to 850mm in width and of weight between 36 ro 60 Kg complete all as specified and as directed |
| 19 | Supply and fixing floor door stopper aluminium alloy body and tongue, anodised with hard drawn steel spring, 150 mm over all length of cover plate complete all as specified and as directed. |
| 20 | Supply and Fixing 5.5mm thickordinary quality glass with film cover, ordinary quality and glazing with oil and putty in square exc 0.5 sqm in each pane complete all as specified and as directed. |
| 21 | Supply and Fixing 5.5mm thickordinary quality glass with film cover, ordinary quality and glazing with oil and putty in square not exc 0.5 sqm in each pane complete all as specified and as directed. |
| 22 | Supply and Fix Solar control film 50 micron reflective type sticked to glass panes as perinstructions of manufacturers of approved colour complete all as specified and as directed. |
| 23 | Material and Labour for pre-laminated particle board 12 mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with rubber beading and screws as in aluminium works etc complete all as specified and directed. |
| 24 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 25 | S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 26 | S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 27 | Material and labour for preparation of old decorated steel & iron surfaces of any description exceeding 10 cm width or grith not otherwise specified and applying two coat of synthentic enamel paint all as specified and as directed. |
| 28 | Demolition of brick work / stone boulder / PCC block masonary, built in cement mortar or cement lime mortar including all quoins, arches pillars, etc but excluding ashlar facing, dressed stone works, precast concrete articles and precast concrete block wallings complete all as specified and as directed. |
| 29 | M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 30 | Material and Labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 31 | M&L mild steel TMT bars 5mm dia and over up to 10mm for stirrups cut to length , bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia bars confirming to Fe-410-S or Fe-410-0 complete in all respect as specified and directed. |
| 32 | Material and labour for rendering 10mm thick in Cement Mortar 1:6 on fair faces of brick walls or on concrete surfaces, finished even and smooth,without using extra cement complete all as specified and directed. |
| 33 | Material and labour for 15 mm thick rendering on brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick, finished even and smooth without using extra cement complete all as specified and as directed. |
| 34 | Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of distemper oil-emulsion of approved shade/tint over a coat of primer, over surface of wall all as specified and as directed. |
| 35 | Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 36 | M&L for complete removal by Washing, rubbing down and stopping and preperation of distempered and painted surfaces of walls, pillars,cornices by brooming down etc including filling depressions of scrapped surfaces with wall care putty (1 mm thick) and preparation of surfaces for further treatment and applying two coats of distemper oil emulsion over a coat of primer complete all as specified & directed. |
| 37 | Material and labour for complete removal by Washing, rubbing down and stopping, preparing old external plaster surface of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 38 | Demolition of reinforced cement concrete of any description ad in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 39 | Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork, complete all as specified and as directed. |
| 40 | Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out getting out in soft/loose soil, complete all as specified and as directed. |
| 41 | Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed. |
| 42 | Removing excavated material (soil) n exc 50 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. |
| 43 | Supply and laying Reinforced cement concrete hume pipes class NP3, laid and jointed complete with one collar per length of pipe, dia 300 mm complete all as specified and as directed. |
| 44 | M&L for concrete bed to drains to drain pipes including packing under and completely sorrounding pipes with cement concrete 1:3:6 type C2, with using 40 mm graded stone aggregate after they are laid and tested in for 300 mm dia pipe complete all as specified and as directed. |
| 45 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators sockets etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc. |
| 46 | M&L point wiring complete with 1.5 Sqm sincle core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc, all as specified and as directed for the following :- |
| 47 | (a)One light point or one light/ exhaust fan/ fan point controlled by one switch |
| 48 | (b) One 3 pin socket outlet 5 Amps on same board |
| 49 | (c) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board. Please Enable Macros to View BoQ information |
| 50 | (c) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender