Tender For Special Repairs To Bldg No P-165 (Yos Otm Accn) At Pvkc Saw (Total 04 Rooms) Acc&S Under Ge(N) Ahilyanagr
Tender Value
35.82 Lakhs
Estimated cost
Bid Submission
30 Sep 2026
5 days left
EMD
72000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmednagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Bldg No P-165 (Yos Otm Accn) At Pvkc Saw (Total 04 Rooms) Acc&S Under Ge(N) Ahilyanagr
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or concrete surfaces on wall/ ceilling/ stone/ block etc including racking out joint, hacking for key, scrubbing down with water etc all as specified and as directed |
| 2 | Demolition of brick work or stone/ boulder masonry/PCC block, built in cement mortar or cement lime mortar including all quoins, pillars etc. |
| 3 | M&L for Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed. |
| 4 | M&L for special treatment ot sunken portion with 10mm thick plaster in CM 1:4 with WPC liquid chemical and applying one coat chemical on plastered surface rendering again 10mm thick in CM 1:4 mixed with chemical filling the sunken floor with PCC 1:5:10 using brick bat area of floor upto 5.00 Sqm including 40 mm dia 0.60 m pipe etc complete all as specified and directed by Engineer-in-Charge. |
| 5 | M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement with WPC.Note:- WPC shall be measured & paid seperately. |
| 6 | M&L for rendering 10 mm thick in CM 1:6 over brick surfaces, finished even and smooth without using extra cement all as specified and as directed. |
| 7 | M&L for rendering 5 mm thick in CM 1:3 on ceillng, finished even and smooth all as specified and as directed. |
| 8 | M&L for applying two coats of OBD over a coat of primer Chalk whiting, on plastered surfaces, preparatory to distempering on newly plastered wall surfaces / ceiling and including wall care putty all as specified and as directed. |
| 9 | M&L for preparing of new surface and applying two coat of Apex exterior paint of required colour shade on surface of walls including primer and scaffolding at any height complete all as specified and directed by Engr-in-charge. |
| 10 | M&L for preparing of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint including scaffolding at any height complete all as specified and directed by Engineer-in-charge. |
| 11 | M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) including scaffolding at any height complete all as specified and directed by Enggineer-in-charge.. |
| 12 | M&L for complete removal of existing treatment and prepartion of surfaces on surfaces of walls / ceilings and applying two coat of acrylic distemper Chalk whiting, on plastered surfaces, preparatory to distempering including wall care putty scaffolding at any height complete all as specified and directed by Enggineer-in-charge. |
| 13 | M&L for preparing old painted surfaces by washing, rubbing down and stopping of painted surfaces and applying one coat or more coat of Apex exterior paint of required colour shade on surface of walls including scaffolding at any height complete all as specified and directed by Enggineer-in-charge. |
| 14 | Material and labour for repair to crack including cutting V groove along cracks removing all dust and loosely laid particles using a blower wetting the crack using water and filling the crack using crack seal compound paste as per manufactures instructions and finishing using putty blade complete all as specified and directed at any height incuding necessary scaffolding. Make : Fosroc renderoc CS/ Sika cracksil/ Pidilite Dr fixit 217 Crack x Shrinkfree. |
| 15 | Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor finishes |
| 16 | M&L for 75mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base floor |
| 17 | Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for. |
| 18 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc |
| 19 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed . |
| 20 | M&L for RCC (1:2:4) nominal mix type B1 using 20mm graded stone agregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed . |
| 21 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 22 | S&F double chraged Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished of each tiles 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6 complete all as specified and directed by Enggineer-in-charge. |
| 23 | S&F for double chraged Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished of each tiles 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado complete all as specified and directed by Enggineer-in-charge. |
| 24 | S&F coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6 |
| 25 | M&L for Glazed ceramic coloured in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado all as specified and as directed. |
| 26 | Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors aprons etc. |
| 27 | Material and labour for machine cut cudappah stone 18-20 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed for vertical support. |
| 28 | M&L for 20 to 25 mm thick Rough dressed shahabad stone slab flooring, laid dry but jointed and pointed in cement mortar 1:3 including 15 mm thick screed bed in cement and sand mortar (1:6), etc complete all as specified and directed by Engineer-in-Charge. |
| 29 | M&L for 18 to 20mm thick granite (of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like in cement (1:4) including pointing in wihte cement (1:2) using marble dust with admixture of pigment ot match with shade of granite including moulding or rounding of edges, machine polishing to edge to give high gloss finish complete all as specified. |
| 30 | M&L for Providing and laying 60mm thick factory made glossy finished chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand (sand cushion), compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete all as specified and directed by Engineer-in-Charge. |
| 31 | Taking down of chowkat with shutter without taking off shutters from the frame exceeding 1.5sqm each but not exceeding 4 sqm all as specified and as directed. |
| 32 | Taking down of chowkat with shutter without taking off shutters from the frame, not exceeding 1.5sqm each all as specified and as directed. |
| 33 | M&L for re-fixining same opening of shutters of any description exceeding 1 sqm each and not exceeding 2 sqm each all as specified and as directed. |
| 34 | S&F for Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 35 | S&F for 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 36 | S&F Aluminium framed windows any pattern, fixed/side hung/silding (three track) using powder coated of thickness 50 micron alluminium sections, of approved make with or with out sash bars suitable for 4.80mm thick glazing including necessary jointed cleats, glazing all as specified Note-: (glazing shall be measured and paid separatly) |
| 37 | S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 38 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates, grills, etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab and wooden Frames with suitable arrangement. |
| 39 | S&F 30mm thick flush door shutter soild core construction with block board core and plywood face panels commercial type on both sides . |
| 40 | S&F second class hardwood glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass gauge etc with sash bar divided into squares edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass or gauze etc sizes of members of shutters as specified inSSR part-I section 8 clause 8.20 (a) fitted to chowkats. |
| 41 | S&F sheet glass ordinary quality 3 mm thick with oil putty not exceeding 0.5 sqm in each pane all as specified and as directed. |
| 42 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples all as specified and as directed. |
| 43 | .-Ditto- all as per ser item 42 above but fixed in repair to steel/wooden shutters |
| 44 | S&F in repair butt hinge, stainless steel 100mm long all as specified and as directed. |
| 45 | S&F in repair butt hinges stainless steel 75mm long all as specified and as directed. |
| 46 | S&F aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy 300 mm long and fixed all as specified and as directed. |
| 47 | S&F Floor door stopper of aluminium alloy body double and tongue anodised with rubber shoe and fixed of size 150 mm all as specified and as directed. |
| 48 | S&F aluminium anodised barred tower bolt of extruded section 200 mm long and fixed all as specified and as directed. |
| 49 | S&F extruded aluminium alloy handle fabricated type anodised 150 mm long |
| 50 | .-Ditto- all as per ser item No 49 above but 100mm long |
| 51 | M&L for preparing new surfaces of wood of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed. |
| 52 | .-Ditto- all as per ser item No 51 above but on steel surfaces over red oxide primer |
| 53 | S&F of Harrison/ curtain rails, stainless steel, chromium plated with fixing SS brackets, SS stops, SS rollers etc all as specifed and as directed by Engr-in-Charge. (All materials shall be stainless steel). |
| 54 | S&F in repair aluminium extruded Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed |
| 55 | S&F IInd class hard wood plain solid, straight ,chowkats and frame, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints all as specified and as directed. |
| 56 | S&F hasp and staple, safety type aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw 125 mm long all as specified and as directed. |
| 57 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water / moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, icluding Magnets and CP Handles all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges shall be paid separately) incl taking down old one. |
| 58 | S&F 25mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work all as specified. |
| 59 | S&F 1.5 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved , fixed with approved adhesive as per manufacturer's instruction |
| 60 | S&F Pressed steel frames for doors with one or more rebates of size 125 x 60mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed. |
| 61 | S&F in repair vitreous china wash basin, white back, nearest size 500 X 400 mm x 190 mm , errecting on existing CI brackets including taking down old one all as specified and as directed. Note: If the mentioned size is not available in the market, the next immediate higher size shall be provided by the contractor. Make of Cera Code : S2040121 or others equivalent in approved make. |
| 62 | S&F in repairs Vitreous Ware wash down water closet (Pedestal), white (EWC) and including seat cover with brass screws and excluding flush pipe and flushing cystren. Make of Cera or others equivalent in approved make. |
| 63 | S&F in repair 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and taking down old one complete all as specified and as directed. Make of Cera Code : B1010110 SN or others equivalent in approved make. |
| 64 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long. Make of Cera or others equivalent in approved make. |
| 65 | S&F in repair Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm.Make of Cera Code : F5013116 / F5015116CH or others equivalent in approved make. |
| 66 | S&F Towel Ring of stainless steel and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms). Make of Cera Code :F5015105CH or others equivalent in approved make. |
| 67 | S&F in repairs Towel Rail 600mm long of brass chromium plated D type with and including Chromium plated brass screws and wooden/ plastic cleats complete all as specified and as directed. |
| 68 | S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.Make of Cera Code : F5013110 or others equivalent in approved make. |
| 69 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified Make of Cera Code : F8030103 or others equivalent in approved make. |
| 70 | Taking up or down steel tubing 15mm dia and connections, including cleaning for re- fixing or removal to store. |
| 71 | Taking up or down steel tubing 20mm dia and connections, including cleaning for re- fixing or removal to store. |
| 72 | S&F 16 mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 73 | S&F 20 mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 74 | Dismantling existing PVC water tanks of capacity exc 250 litres & n.exc 500 litres all as directed and removed from site. NOTE:-Dismantled water tank shall become the contractors property as per Sch of credit. |
| 75 | S&F 1000 litres rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position including brass gate valve crutch or butterfly handle and GI suitable nipple at outlet all as specified and directed. |
| 76 | S&F in repairs PVC float valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe ferrule |
| 77 | S&F in repairs stop valves / angle cock cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe 15mm (fancy type chromium plated).Make of Cera Code : F2002201 or others equivalent in approved make. |
| 78 | S&F in repairs 15mm dia Chromium plated fancy type long body Bib tap cast copper alloy with crutch or butterfly handles screwed down screwed for iron pipe fixed in repair all as spd & directed . Make of Cera Code : F1015151 or others equivalent in approved make. |
| 79 | S&F in repairs 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed Make of Cera Code : F1015101 or others equvelent in equivalent make. |
| 80 | S&F in repair Brass chromium Brass CP wall mixer 3 in 1 system with provision of hand shower/overhead shower for mixing hot & cold water screwed down for iron pipe and fixed as all specifed and as directed. Make of Cera Code :F2002401 or others equivalent in approved make. |
| 81 | S&F for 32 / 40 mm suitable PVC flexible waste pipe for wash hand basin, kitchen sink and urinals pot |
| 82 | S&F SS grating doom 200 X 100 mm with waste hole / without hole. (Minimum weight 40gms) |
| 83 | S&F in repair Chromium plated shower roses 150 mm size with or without swevel joints and size including fixing to steel pipe or union. |
| 84 | S&F PVC connections 15mm size with PTMT nuts of length 450mm |
| 85 | S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls. |
| 86 | S&F 110 mm bore PVC (SWR) bends of any radius. |
| 87 | S&F 110 mm bore PVC (SWR) branch piece single (Single `Y') equal or unequal with access door. |
| 88 | S&F PVC (SWR) pipes single socketed, 75mm dia in any length with rubber ring joints, laid in trenches or in floors |
| 89 | S&F PVC (SWR) bends any radius 75mm bore |
| 90 | S&F PVC (SWR) multi floor trap 75mm dia with grating including jointing with solvent cement |
| 91 | S&F 5.5 mm thick Fancy type beveled edge mirror of selected quality glass and fixed to wooden plugs / aluminium brackets with chromium plated brass screws and cup washers all as specified and as directed. |
| 92 | S&F for 12mm thick Toughened glass as in hinged doors, partitions automatic doors / sliding doors and similar work including cutting to shape, drilling holes, approved film/selected film, SS handles, lock and all sliding accessories complete all as specified and directed by Engr-in-Charge. |
| 93 | M&L for Roof tiles, Mangalore pattern, interlocking at side joints, laid in cement mortar (1:4) including Demolition of Single layer Mangalore pattern or similar tiles in roofing portions bedded in cement mortar complete all as specified and as directed. |
| 94 | Taking down carefully existing unserviceable bitumen felt(any number of layers) including plaster of any thickness, wire brushing and cleaning of the surface of roof terraces / chajja including flashing and junctions of parapets kerb wall, PCC fillets, benching etc and removing of the rubbish to a distance not exceeding 500 m from the building and depositing where complete all as specified and directed |
| 95 | M&L for rendering 10 mm thick in CM (1:4) on roof slab / chajja top finished even and fair without using extra cement with WPC complete all as specified. Note:- WPC shall be measured & paid seperately. |
| 96 | Supply only integral water proofing compound |
| 97 | Demolition of plain cement concrete (unreinforced) in ground floor including concrete at junctions of parapets, chajjas and roof terraces, flashing kerbs walls, PCC fillets, benching coving of chajjah top/junctions etc complete all as specified |
| 98 | Material and labour for providing plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) for roof, chajjas,kerb, or mud stops, rounded or chamfered on edges etc complete all as specified and as directed. |
| 99 | M&L for preparation of surfaces thoroughly by cleaning, washing and removing dust, dirt, oil and loose particles and applying special grade of primer PR-71 of chokesy chemicals 1.10 Kg/Sqm or equivelent of Dr fixit, Pidilite, Asian, Sika. Note:- Application of liquid water proof material only will be carried out thorugh manufactures. |
| 100 | M&L preparation for applying two coats (with colour pigment) of high performance PU based cold applied elastomeric coating having solid content 80% shore, a hardness Min 60,tensile strength 1.50 to 2.0 N/mm2 TECH O THANE PU white @ 0.95 Kg per Sqm (0.45 Kg /Sqm /per coat) with dry film thickness of 1 to 1.20 mm on previously primed surface of chokesy chemical or equivelent of Dr.Fixit, pidilite, Asian, Sika. Note:- Application of liquid water proof material only will be carried out thorugh authorised manufactures. 05 years waranty will be submitted by manufacturer. |
| 101 | Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors, etc. all as specified and directed. |
| 102 | M&L for point wiring complete concealed type with two runs of 1.5 Sqmm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn through and including PVC rigid conduit not less than 20 mm dia with its accessories with Flush mounting modular metal boxes (upto 18 module suitble for Mylinc series of Legrand with and including white plates with frame upto 18 module of make suitable for Mylinc Series) for fixing switches/ socket/ regulators etc with and including 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, etc complete all as specified and directed by Engineer-in-Charge. Note :1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black)2. Wiring shall be done as per complaints received from user 3. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc |
| 103 | One light point /fan point/bell point controlled by one switch with cables 1.5 sq. mm size |
| 104 | One light point controlled by two, 2 way switches, with cable 1.5 Sqmm |
| 105 | One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size |
| 106 | One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size |
| 107 | .--Do-- all as per Ser item No 102 above with but 2.5 sqmm size cable for, 3 pin socket 15 Amp |
| 108 | S&F Modular switch 1 way 6A, 1 module |
| 109 | S&F Modular switch 2 way 6A, 1 module |
| 110 | S&F Modular switch 1 way 16A, 1 module |
| 111 | S&F Socket, 6A - 2/3 pin combined 2 module |
| 112 | S&F Socket 6A/16A - 2/3 pin combined 2 module |
| 113 | S&F Modular Bell push 6A, 1 module. |
| 114 | S&F Bell Multi Music type. |
| 115 | S&F Fan step regulator, 120W - 2 module |
| 116 | Supply & fix lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting complete all as specified & directed |
| 117 | S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body all as speccified and directed |
| 118 | Taking down carefully MCBs DBs etc.and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors, etc. all as specified and directed. |
| 119 | S&F double door Sheet metal enclosures factory made DBs 4 way, (TPN DB's) 415 volts protection class IP-43, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 200 Amps rated copper Busbar, With Neutral bar, Earthbar and Cable lies for Cable management, Fully shrouded, Neutral bars, Prefitted masking sheet complete all as specified and as directed. |
| 120 | S&F in replacement double door Sheet metal enclosures factory made DBs 08 way, (SPN DB's) 240 volts protection class IP-43, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 200 Amps rated copper Busbar, With Neutral bar, Earthbar and Cable lies for Cable management, Fully shrouded, Neutral bars, Prefitted masking sheet complete all as specified and as directed. |
| 121 | S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps for AC connection complete all as specified and as directed. |
| 122 | Supply & fix MCB , SP, AC, 240 volts of 06 to 40 Amps, 10 KA Capacity, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 123 | Supply & fix MCBs , TPN, AC, 415 volts of 40 Amps, 10 KA Capacity, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 124 | Supply & fix MCB, SPN, AC, 240 volts of 40 Amps, 10 KA Capacity, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 125 | Supply and fix Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 20 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge . |
| 126 | S&F E-LITE LED Pride Plus NEO decorative slim squre profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 Sqmm complete with all accessories all as specified & directed |
| 127 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. |
| 128 | S & F Lumeno LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 950 suitable for \\"B-22 type to fix on batten holder and wall light etc complete all as specified and directed by Engineer-in-Charge |
| 129 | S&F in replacement Superb LED street light fitting 25 Watt waterproof IP65, dust and waterproof LED luminaire with polycarbonate Housing suitable for (Bldg security light) fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V , 50 HZ, complete all as specified and as directed |
| 130 | S&F sub main wiring concealed with two single core PVC insulated,unsheathed, FRLS stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLS stranded copper conductor cable as earth wire drawn through and including PVC Conduit 20 mm dia ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note :1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black)2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Conduit shall be measured as one unit |
| 131 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25mtr depth and top edge of the earth plate not less than 1.5mtr below normal ground level connected to galvanised earth lead wire 4.0Sqmm dia by means of nuts,bolts & washer etc. Earth wire connected upto main earth point/DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 ( using 20 mm graded stone agregate) and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of ms bar @ 15 mm CIC with both way lifting arrangement complete including all necessary excavation & earth work all as specified and directed. |
| 132 | Taking down old electric meters, removing materials & deposit to MES store for keeping in safe custody. |
| 133 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200mm. |
| 134 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc |
| 135 | Supply & fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender