Tender For Special Repair To Bldg No P-118 (Jco Md Accn) At Kalina Under Ge(N)Santacruz.
Tender Value
1.46 Crore
Estimated cost
Bid Submission
17 Oct 2026
0 days left
EMD
2.21 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai Suburban → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-118 (Jco Md Accn) At Kalina Under Ge(N)Santacruz.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 22-Sep-2026 | CORRIGENDUM NO.1 | BOQ | 10-Oct-2026 |
| 2 | 10-Oct-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 17-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work built in cement mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge. |
| 2 | M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 3 | M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius in 1/2 brick thick walls, built in cement morter 1:4 complete all as specified and as directed. |
| 4 | Demolition cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), incl tiles complete all as specified and directed. |
| 5 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for. |
| 6 | Dismantling of Asbestos Cement corrugated sheet in roof coverings |
| 7 | M & L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 8 | M&L preparing new steel surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 9 | S & F pre-painted galvalum aluminium zinc coated GI based colour corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 mpa as in wall cladding and roof fixed with self tapping screws as per manufacturers instruction/recommendations complete all as specified and directed by Engr-in-Charge. |
| 10 | S & F pre-painted galvalum aluminium zinc coated GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 mpa as in wall cladding and roof fixed with self tapping screws as per manufacturers instruction/recommendations complete all as specified and directed by Engr-in-Charge. |
| 11 | Taking down Chowkhats or frames not exc. 1.5sq. m each (Without taking off shutters from the frames ) including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 12 | Taking down Chowkhats or frames exc. 1.5 sqm but n exc 4 sqm. m each (Without taking off shutters from the frames) including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 13 | Taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 14 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 15 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 16 | M & L for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.Note : SS butt hinges and necessory SS screws shall be paid separately |
| 17 | S&F 35mm thick 2nd class hard Sal wood glazed & skeleton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc. complete all as specified and as directed by Engineer-in-Charge. |
| 18 | S&F PVC door frame of size 50 mm x 47 mm made of 5 mm prelam PVC sheet and edges will be painted to match with prelam sheet. |
| 19 | Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat molded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 149 of SSR Part II (pertaining to item No 08080)complete all as specified and as directed by Engineer-in-Charge. |
| 20 | M & L for mild steel work in hold fast & similar small articles conforming to Fe 290 Gd 165 complete all as specified and as directed by Engineer in Charge |
| 21 | M & L for 1:3:6 (20mm graded aggregate) , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, HOLD FAST string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed. |
| 22 | S & F in repairs for 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 23 | S&F 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor. |
| 24 | S&F 100 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, and fixed. |
| 25 | S&F 125 mm long butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, and fixed. |
| 26 | S&F aluminium anodised barrel tower bolt of extruded section size 150mm ISI marked. |
| 27 | S&F 100 mm long extruded aluminium alloy handles fabricated type anodised ISI marked. |
| 28 | S&F 150 mm long extruded aluminium alloy handles fabricated type anodised ISI marked. |
| 29 | S&F aluminium alloy, anodised, 300mm long sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet. |
| 30 | M & L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket Aluminium sections shall be smooth, rust free, straight, mitredand jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.Note : (i) Glass panes will measured & paid separately . (ii) Rubber beading will not be weighed. |
| 31 | M & L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 32 | S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge. |
| 33 | S&F 4 mm thick Sheet glass ordinary quality in square n exc 0.5 Sqm each complete all as specified and directed. |
| 34 | S&F 4 mm thick Sheet glass ordinary quality in square exc 0.5 Sqm each complete all as specified and directed. |
| 35 | S&F 4 mm thick figured glass, pin head type in square n.exc 0.5 sqm each pane |
| 36 | S&F aluminium anodised wire cloth 0.45 nominal dia of wire and average width of aperature 1.40 and fixed with stainless steel wire staple. |
| 37 | S&F in repairs aluminium anodised wire cloth 0.45 nominal dia of wire and average width of aperature 1.40 and fixed with stainless steel wire staple. |
| 38 | S&F in repairs PVC low level flushing cistern of capacity 10 ltr. white with inlet, ball valve, float and handle including breckets, flush pipe of polyethylene of low or high density or PVC 32mm dia and connection to pipes and fixing of chains and pull or lever. |
| 39 | S & F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 40 | S&F in repairs wash basins, vitreous china(flat back or angle back type) size 550 X 400mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of supply and waste pipe complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F in repairs fancy type 15mm dia pillar taps swan neck , cast copper alloy, with capstan heads, chromium plated complete all as specified and directed by Engr-in-Charge. |
| 42 | S&F in repairs, bib taps fancy type chromium plated, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed. |
| 43 | S&F in repairs, conceal stop valve fancy type cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed. |
| 44 | M & L in repairs for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and as directed by Engr-in-Charge. |
| 45 | M & L in repairs for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and as directed by Engr-in-Charge. |
| 46 | M&L for 15mm thick rendering in cement mortar (1:3) on SUNKAN floor including water proofing compound as per specified including vertical surfaces up to 450 mm hight and using and applying a coat of Raincoat soulation of Make Dr Fixit and equvaint with uniform surfaces and S & F for vitreous china squatting pan, 'Orrisa' pattern/pedestal pattern, size 580 x 440mm including 'P' trap and connector pices of CI Pipe as per required upto T /Y joint Including filling PCC 1:4:8 type D2 and over 40 mm thick PCC 1:2:4 for sub base type B 2 for uniform surfaces and GI Spout with 50 mm dia to provide that 450mm long to be extended front out surfaces of wall all as specified ad directed by Engr-in Charge . |
| 47 | S&F in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. complete all as specified and directed. |
| 48 | S & F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor |
| 49 | S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm |
| 50 | S & F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. |
| 51 | S & F in repair, brass chromium plated 125mm Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) |
| 52 | S&F Mild steel galvanized steel tubing medium grade 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floors complete including taking down old u/s pipes |
| 53 | S&F Mild steel galvanized steel tubing medium grade 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floors complete including taking down old u/s pipes |
| 54 | S&F Mild steel galvanized steel tubing medium grade 25 mm bore with all fittings and fixed complete to walls and ceiling or laid in floors complete including taking down old u/s pipes |
| 55 | S & F PVC SWR Single socketed rain water pipes/soil waste pipes with rubber ring joints 110mm dia fixed to wall including taking down old u/s pipes |
| 56 | S & F PVC SWR Single socketed rain water pipes/soil waste pipes with rubber ring joints 75mm dia fixed to wall including taking down old u/s pipes |
| 57 | S&F 110mm bore PVC (SWR) bends any radius |
| 58 | S&F 75mm bore PVC (SWR) bends any radius |
| 59 | S&F PVS(SWR) Vent cowl 110mm dia. |
| 60 | S&F PVS(SWR) Vent cowl 75mm dia. |
| 61 | M & L for PCC 1:2:4 type B0 using (12.5mm graded aggregate) with 2% by weigth of cement or as per manufacturer instruction waterproofing as in levelling course haunching, coping and similar works over RCC roof surface and RCC overhead tank top surface including rounded and chamfered on edges and formwork etc all as specified and directed |
| 62 | S & F for Rotational moulded polyethylene water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, etc including dismantlig of existing water tank and removing to store,etc all as specified and directed |
| 63 | S & F for 25mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed etc all as specified and directed |
| 64 | S & F in repairs for 25mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed etc all as specified and directed |
| 65 | S & F for 20mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed etc all as specified and directed |
| 66 | S & F in repairs for 20mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed etc all as specified and directed |
| 67 | S & F in repairs 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) |
| 68 | S & F 15mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) |
| 69 | M & L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall |
| 70 | M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors |
| 71 | M & L Broken stone or boulder Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 72 | M&L for 75mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/ hard standing path and finishing the surface even and fair without using extra cement all as specified and directed. |
| 73 | M&L for 100 mm thick (1:2:4) Type B-1, Plain cement concrete with using 20mm graded aggregate as in ground floors finished even and smooth without using extra cement, complete all as specified and directed. |
| 74 | M & L for 25mm thick as in levelling course cement concrete type B1, 1:2:4 (20mm graded aggregate) |
| 75 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles up to a lead of 5 Km and rubbish off the premises complete all as specified and directed. |
| 76 | M & L for light shade virified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 77 | M & L for virified ceramic tiles 10 mm thick (square/ rectangular) polished as in skirting, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10 mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 78 | M&L for Non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement incl 15 mm thick screed bed in CM 1:4 . |
| 79 | S&F glazed ceramic Coloured tiles over vertical surface of wall,350x250x 7mm/ 450x350x7mm thick (or nearest size), set and jointed in neat cement slurry and pointed in coloured cement to match including backing coat of 10mm thick in CM(1:4) complete all as specified and directed. |
| 80 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar. |
| 81 | M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite., incl 15 mm thick screed bed in CM 1:6 , |
| 82 | M&L for Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed |
| 83 | M&L for Green Marble work of 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement in CM (1:2) using marble dust with admixture of pigment to match with marble shade of green marble., incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge. |
| 84 | M & L for mirror polished Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey ement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed. |
| 85 | M & L for mirror polished Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including backing coat Rendering 10mm thick on fair faces in CM 1:6 of brick work or concrete surfaces complete all as specified and directed. |
| 86 | M & L for Machine cut cudappah stone slab over cooking plateform 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 87 | S&F of 18mm thick rajashri celuka ply of one sides prelam/rigidlam and other side plain white colour to make kitchen cabinet shutter/drawer front shutters complete all as per specifications and as directed by Eng-in-charge. (taking down taken in Item No 11) |
| 88 | S&F of 18mm thick rajashri celuka ply of plain colour fixed with screws, solvent cement/adhesive to make kitchen cabinet sides , top and bottom and shelves inside the cainets complete all as per specifications and as directed by eng-in-charge |
| 89 | S&F of auto closing hinges openable at 0 degree for kitchen cabinet shutters as per directed. |
| 90 | S&F of SS handles of 100mm size for kithchen cabinet shutters, etc. as per directed. |
| 91 | M&L for preparing old wood based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-Charge. |
| 92 | Demolition of reinforcement cement concrete (reinforcement cut as required to facilitate demolition) of any position (column, Beam, chajja, fins,RCC water tank and Roof slab etc) ground floor/other than ground floor complete all as specified and as directed by Engr-in-charge. |
| 93 | Providing and applying rust cleaner (Re-backler solution) to exposed corroded reinforcement @ 0.20 Litre/Sq or approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc. complete as directed by Engineer-In-Charge. Please Enable Macros to View BoQ information |
| 94 | Providing and applying rust cleaner (Re-backler solution) to exposed corroded reinforcement @ 0.20 Litre/Sq or approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc. complete as directed by Engineer-In-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 10, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 10, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Oct 17, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
CompletedOct 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender