Tender For Addition/Alteration And Special Repair Of Certain Md Accn At Dehradun.
Tender Value
9.27 Crore
Estimated cost
Bid Submission
14 Oct 2026
18 days left
EMD
7.89 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dehradun → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration And Special Repair Of Certain Md Accn At Dehradun.
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE A PART-I (BUILDING WORK) |
| 2 | Provision of additional rooms in the existing Md accn (Double Story) complete all as specified and as shown on drawing Note:- (i) One Block of Md Accn consist of four quarter.(ii) Provision of additional rooms in all four quarter is include in the scope of work.(iii) The Architectural and structural Drawing shows only half block consisting of two quarter whereas the other half is mirror image of it and all four quarter are included in the scope of work.(iv) Contractor shall consider extension to all four quarters including finshises (as per drgs and tender docs) while quoting rate for the item. |
| 3 | SCHEDULE A PART II-A (Internal Water Supply) for details refer Sch A in pdf folder |
| 4 | SCHEDULE A PART II-B (Internal Water Supply) |
| 5 | Supply and fixing 15 mm bore dia two way Angle valves, cast copper alloy, fancy type chromium plated (quarter turn) with capstan heads or butterfly handle screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 6 | Supply and fixing 15 mm bore dia brass chromium plated single lever 3-in-1 wall mixture with provn of bath hand shower or over head shower complete with 115 mm long band pipe on upper side conneting legs & wall flanges and fixed complete all as specified and directed. |
| 7 | SCHEDULE A PART III ( SITE CLEARANCE AND EARTH WORK) for details refer Sch A in pdf folder |
| 8 | SCHEDULE A PART IV (ROAD/PATH/CULVERT for details refer Sch A in pdf folder |
| 9 | SCHEDULE A PART V-A (SEWAGE DISPOSAL) for details refer Sch A in pdf folder |
| 10 | SCHEDULE A PART V-B (SEWAGE DISPOSAL) |
| 11 | M & L RCC Septic tank for 50 users conventional type designed to carry sewage and sludge water excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 design mix in walls, base slab, baffle walls and roof slab including beams etc with vent shaft, manhole openings with cover connection etc complete all as specified and as shown on Drgs No TD-129 sh1/3 to 3/3 complete all as specified and directed. |
| 12 | M & L Soakage well excavation, in any type of soil,foundation in PCC 1:3:6,walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in CM,RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size of 3.00 M dia × 4.50 M effective depth complete all as shown on Drg No TD -309 Sht 1/4 to 4/4 complete all as specified and directed. |
| 13 | Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed by Engineer-In- Charge. |
| 14 | Desludging/desilting of 150 mm dia sewage lines including manholes, up to 2.0 m depth by removing blockage if any by means of rodding manually or mechanically by pumping out water where required and removing residual silt/mud/peat/sludge out side of defence land complete all as directed by Engr-in-charge. |
| 15 | SCHEDULE A PART VI (MISCE.) BR WORKS |
| 16 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete as directed and specified. |
| 17 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete as directed and specified. |
| 18 | Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 19 | Demolition of concrete of any description and in any position not otherwise specifically provided for Complete all as specified and as directed. |
| 20 | Demolition of cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed |
| 21 | Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 22 | Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified. |
| 23 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed. |
| 24 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed. |
| 25 | Taking down shutter of any description exc. 1.0 Sqm but n.exc 2.0 Sqm each and removing from site complete all as specified and directed. |
| 26 | Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed. |
| 27 | Taking up or down 15 mm steel tubing and connections complete all as specified and directed. |
| 28 | Taking up or down 20 mm steel tubing and connections complete all as specified and directed. |
| 29 | Dismantling of water tanks capacity exc 250 ltrs and n.exc 500 ltrs complete all as specified and directed. |
| 30 | Dismantling of water tanks capacity exc 500 ltrs and n.exc 1000 ltrs complete all as specified and directed. |
| 31 | M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded aggregate in floor sub base complete all as specified and directed |
| 32 | M&L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed |
| 33 | M&L for Non skid coloured ceramic tiles 400 X 400 X 7 to 8 mm thick (square/ rectangular) on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick in cement mortar 1:6. Complete all as specified and directed. |
| 34 | M & L for colour vitrified double charged any shade tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm laid in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, complete all as specified and directed |
| 35 | M & L for colour vitrified double charged any shade tiles 8 to 10 mm thick (square/ rectangular) as in Skirting, riser etc (length of tiles not less than 600 mm) set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed |
| 36 | M & L for non-skid coloured ceramic joint free tiles 8 to 10 mm thick (square/ rectangular) of size 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed. |
| 37 | M & L for non-skid coloured ceramic joint free tiles 8 to 10mm thick (square/ rectangular) as in Skirting, riser etc (length of tiles not less than 600 mm) set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed, |
| 38 | M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match on vertical surfaces of wall incl 10 mm thick rendering on brick surface in CM 1:4. complete all as specified and as directed. |
| 39 | M & L for 18 to 20 mm thick prepolished machine cut kota stone slab as in flooring incl 20 mm thick cement screed base in CM 1:6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing and polishing. complete all as specified and directed. |
| 40 | M & L for 18 to 20 mm thick prepolished machine cut kota stone tile/slab as in vertical surfaces of walls, skirting or dados incl 10 mm thick cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing and polishing. complete all as specified and directed. |
| 41 | M & L 16 to 18 mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge. |
| 42 | M&L 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed. |
| 43 | M&L for fly ash brick work with old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed. |
| 44 | M&L for brick work with old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) except brick complete all as specified and directed. |
| 45 | Taking down existing un-serviceable water proofing treatment from roof slab and cleaning the roof slab by wire brush up to mother slab and removing WPT felt exc 500 mtr but not exc 1.50 Km etc complete all as specified and as directed |
| 46 | M&L for cement concrete 1:2:4 type, B0 using 12.5 mm graded stone aggregates as in copings, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed Note: Work shall be carried out upto 3 storey. Rates of necessary scaffolding deemed to be include in this item |
| 47 | M & L for water proofing treatment to non-accessible roof slab with APP based madified polymeric membrane as per manufacturers instructions with following course of description below:-(a) Applying a priming coat of bituminous primer @ 0.30 kg / sqm, till the surface is properly impregnated.(b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6 kg / sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms /sqm) centre core, laid on primed surface Fixed with hot molten bitumen of grade 85/25 @ 1.2 Kg / Sqm by forced applications as per manufacturers instructions with side over lap of 100 mm and end overlap of 150 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (c) Apply two coat of bituminous aluminium paint @ 0.20 Kg / Sqm over APP membrane.Note:- 1. The work of water proofing treatment shallbe got executed authorised applicator of the manufacturer only and 10 year company back warranty to be submitted by contrcator.2. The work is required to be carried out at non-accessible roof slab upto three storeyed. The contractor shall make arrangement of scaffolding, safety and security of workers and arrangement for approach to roof. The rates quoted shall be deemed to be included for these items. |
| 48 | M&L cement concrete 1:5:10 type E-2 using 40mm granded brick aggregates as in sunken portion etc complete all as specified and as directed |
| 49 | M&L for applying cement slurry over existing roof surafce @ 3 Kg/Sqm incl mixing with water proofing liquid @ 0.15 Ltr per 50 Kg cement bag as per manufacturer's instruction. Complete all as specified and directed. |
| 50 | M&L for rendering 10 mm thick , in cement mortar 1:4 over RCC slab, mixed using water proofing compound liquid @ 200 ml per bag of cement Complete all as specified and directed. |
| 51 | S & F factory made single extruded WPC(Wood polymer composite) Solid door frame/ chowkat of size 50 x 100 mm comprising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge,minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in position with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as specified and directed. |
| 52 | S & F factory made single extruded WPC(Wood polymer composite) Solid door frame/ chowkat of size 65 x 125 mm comprising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge,minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in position with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as specified and directed. |
| 53 | S&F factory made single extruded WPC (Wood polymer Composite) Solid moulded Flush Door Shutter of 35 mm size thick, Pre laminated on both side comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) &900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - in- Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company. |
| 54 | S & F for 30mm thick factory made solid WPC (wood plastic composite) gauged door shutter prelaminated on both side with wiremesh in three number of division with brown wood grain texture including Stainless steel grad 304 wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with (15x5) mm square tubes inside rails with screwing 8x28 heat metal zinc coated screws that can be removed or fixed again after changing of wiremesh when needed covered with moulding beading and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws.. The density of the WPC 650 Kg / cum complete all as specified and directed. |
| 55 | S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated shutter for kitchen, cupboards. The laminated shutter should be pre laminated side with different design and other side plain white of density not less than 650 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed. |
| 56 | S&F factory made single extruded WPC (Wood polymer Composite) Solid moulded Flush Door Shutter of 30 mm size prelaminated on both side comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) &900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - in- Charge, Materia test certificate and authentication should be compulsory provided by the manufacturing company. |
| 57 | S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed. |
| 58 | S & F of powder coated (thickness power coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 59 | S & F of powder coated (thickness power coating not less than 50 micron) aluminium window and ventilator shutters, fixed type without sash bar aluminium section weighing 0.55 kg/m including necesarry joining cleats glazing clips rubber neoprene packing, anodised aluminum snap beading screw lock etc complete all as specified and directed. |
| 60 | Providing and fixing factory made uPVC white colour Sliding window three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware. Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel ghrade 304 wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes 5.5mm thick plain glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) Area not exceeding 2.00 Sqmm each. |
| 61 | S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed. |
| 62 | S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed. |
| 63 | S&F stainless steel wire cloth grade 304 with 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed. |
| 64 | S&F aluminium anodised barrel tower bolt 200 mm long of extruded section etc complete all as specified and as directed |
| 65 | S&F aluminium alloy, anodised sliding door bolt of dia 16mm size 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 66 | S&F 150 mm long aluminium handles cast type, anodised complete all as specified and as directed |
| 67 | S&F 100 mm long aluminium handles cast type, anodised complete all as specified and as directed |
| 68 | S&F double legged floor door stopper 150 mm long aluminium alloy with rubber etc complete all as specified and as directed |
| 69 | S&F ball catches with 8 mm dia steel ball magnet catches for cuboard shutter including strking plate as approved etc complete all as specified and as directed |
| 70 | S&F of 300mm, mild steel ordinary plate type door springs including roller and roller plate including welding to steel frames.complete. |
| 71 | S&F aluminium extruded section body Door closer hydrau lically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed |
| 72 | S&F in repairs stainless steel decorative curtain rod of 25 mm outer dia (min weight 400 gm per RM) complete all as specified and as directed |
| 73 | S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed. |
| 74 | S & F 75mm size stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed. |
| 75 | S&F 500 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. |
| 76 | S&F 1000 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. |
| 77 | S&F in repair 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed |
| 78 | S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed complete all as specified and as directed |
| 79 | M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed |
| 80 | S&F medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 81 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 82 | S&F in repair vitreous chinaware coloured wash hand basin with pedestal of size 55X40 cm complete including CP brass waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed. |
| 83 | S&F in repair vitreous chinaware coloured corner wash hand basin, size 450x300mm as per manufacturer any design approved by GE including CP brass waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed. |
| 84 | S & F in repair Brass CP wall mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed |
| 85 | S & F in repair for brass Chromium plated sink mixer for 15 mm bore pipe complete all as directed |
| 86 | S & F in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed. |
| 87 | S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed |
| 88 | S& F for Swan neck CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed. |
| 89 | S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed |
| 90 | S&F in repairs 600x450 mm size of 5.5mm thickness looking mirror, bevelled edge of selected quality glass with aluminium frame made of channel alround,mounted on 6 mm thick commercial ply or AC building board, fitted to wooden plug with CP screws complete all as specified and directed. |
| 91 | S&F in repair Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. |
| 92 | S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed |
| 93 | S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed. |
| 94 | S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed. |
| 95 | S&F in repair Vitreous China wash down water closet pan padestral pattern with spun pipe 'P' or 'S' trap, white including PVC seat cover and connection to drain or outgoing pipe and flush pipe, anti syphonize pipe etc fixed complete all as specified and as directed. |
| 96 | S&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed |
| 97 | S&F in repair PVC low level flushing cistern valveless, syphonic double action type, ISI mark flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed. |
| 98 | S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Make : ESSCO (Jaquar) Cat No. ALE-CHR-583, Cera Cat No. F 8030108 AB, Hindware Cat No. F-160013) |
| 99 | S & F for Cromium plated two way Angle cock 15mm dia with wall flange. Make – ESSCO (Jaquar) cat No.MQT- 526, Cera cat No. F2004211, Hindware Cat No. F740006) |
| 100 | S&F Toilet paper holder with flat type stainless steel complete all as specified and directed |
| 101 | S&F in repair for 75 mm bore out let cast floor trap spun pipe (conforming to IS 3989) incl cockroach trap with gratings including including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed |
| 102 | S&F for 75 mm bore cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed |
| 103 | S&F for 100 mm bore cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or vertically cast, complete all as specified and as directed |
| 104 | S&F in repair 100 mm bore cast iron bends of (any radius), spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed |
| 105 | S&F in repair 75 mm cast iron cowls spun pipe (conforming to IS 3989) complete all as specified and as directed |
| 106 | S&F in repair stainless steel sink with drainage board 1.00mm thick for kitchen with plug/waste pipe washers including cantiliver bracket or, connecting unions etc over all size 915 x 460mm with bowel size 410mm x 330mm x 160mm complete all as specified and as directed |
| 107 | S&F kitchen plate rack stainless steel 1 mm thick of size 75 cm x 90cm of super delux model with 22 gauge steel and weight not less than 5.5 Kg complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed |
| 108 | S&F for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for cutlery basket,with perforated bottom & side of compacted /slots for holding cutlery of size 510x470x100mm or 520x485x100 mm or 144x 468 x50mm ( clear depth 500 mm) -01Nos Make:- Sleek Elnora ( Asian Paint) Code 600, size 530x505x100 mm/ Godrej product code 6134 baan code LKY2PC214/Evershine size 520x485x95mm Complete all incl fixing of necessary telescopic channels, handels etc as required complete all as specified and as directed. (Make:- Hettich, Godrej or equivalent) |
| 109 | S&F for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for Plain basket of size 510x470x200mm or 520x485x200 mm or 486x500x200 mm , Make:-Sleek Elnora(Asian paint) Code 600, size 530x505x200 mm/Godrej product code 6128, baan code LKY2PB218 /Evershine size 520x485x180 mm .Complete all incl fixing of necessary telescopic channels, handles etc as required complete all as specified and as directed. (Make:- Hettich, Godrej, or equivalent) |
| 110 | M&L cement concrete 1:4:8, Type D-2, using 40 mm graded crushed stone aggregates in foundation filling and mass concrete complete all as specified and directed. |
| 111 | M&L PCC 1:2:4 type B-2 using 20mm graded stone aggregates as in posts filling ,complete all as specified and directed by Engineer-in-Charge. |
| 112 | S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section,MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc complete all as specified and directed by Engr-in-Charge |
| 113 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge |
| 114 | S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge |
| 115 | M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed |
| 116 | M&L for 15mm thick ready mix cement plaster on brick, concrete surfacs and wall/ceiling surface finished even & fair, finishing curring scaffolding etc complete all as specified and directed. Make : ACC (Suraksha/ Ultratech (Readyplast)/ Birla (Aerocom) |
| 117 | M&L for extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work not exc 15 cm in width or girth; including cutting to edges, all mitres and stopped ends etc.complete all as specified and as directed |
| 118 | M&L for complete removal of existing treatment from wall upto plaster surface by washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper all as directed by Engr-in-charge.Note: Work shall be carried out upto 3 storey. Rates of necessary scaffolding deemed to be include in this item |
| 119 | M&L for waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 2 to 3mm mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:-Step 1: Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute.Step 2: Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3: Allow 6-8 hrs time to dry the putty surface. |
| 120 | M&L for applying two coats of Acrylic distemper using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and cetified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.Note : Sanding of surface to be done by mechanical sander with 1500 -2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. |
| 121 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. Complete all as specified and directed.Note: Work shall be carried out upto 3 storey. Rates of necessary scaffolding deemed to be include in this item. |
| 122 | M&L three coats of white wash on ceiling on new/old plastered surfaces including preparation of surfaces complete all as specified and as directed |
| 123 | M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. Note:- Reinforcement to be measured & paid under respective items. |
| 124 | M&L for form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed. |
| 125 | M & L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed. |
| 126 | M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed. |
| 127 | M&L for TMT Bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed. |
| 128 | M & L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 129 | M & L for ATT post construction Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified. |
| 130 | M & L for ATT post construction Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified |
| 131 | M & L for PCC 1: 3 : 6 type C1 using 20 mm graded aggregates in surface channels and drains including necessary use & waste of formwork and demolition of existing old cement concrete of any description complete all as specified and directed. |
| 132 | Extra for forming fair finished drain or channel 30 cm to 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi tred/stopped ends etc complete all as specified and directed. |
| 133 | Supply only liquid water proofing compound complete all as specified and directed. |
| 134 | M&L for exterior grade, heavy duty tile 10-12 mm thick dark shade (as approved by GE) Square/rectangular size 400x400mm, set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. including 15 mm thick cement screed bed in CM 1:6 etc complete all as specified and as directed complete all as specified and as directed |
| 135 | S & F in repair Brass CP WHB mixer of 15 mm bore for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed |
| 136 | M & L for rendering 10mm thick cement mortar 1:4 on roof along with WPC complete all as specified. Water proffing compound shall be measured and paid under respective item. |
| 137 | S & F in repair 75 mm dia cast iron bend spun pipe confirming to IS 3989 diminishing pices or tapper complete all as specified and directed. |
| 138 | S & F in repair branch pices 100 mm dia cast iron bend spun pipe Y/T- shaped, single (equal/unequal) ordinary or inverted (spigot or scoket type) or with parallel branches complete all as specified and directed. |
| 139 | S & F in repair branch pices 75 mm dia cast iron bend spun pipe Y/T- shaped, single (equal/unequal) ordinary or inverted (spigot or scoket type) or with parallel branches complete all as specified and directed. |
| 140 | SCHEDULE A PART VII (MISCE.) EM WORKS Please Enable Macros to View BoQ information |
| 141 | SCHEDULE A PART VII (MISCE.) EM WORKS Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender