Tender For Lac-Ads-Mla Ads 2025-26 - Vengola Gp - Completion Of Drinking Water Scheme Ward 14 - Pipe Line And Electrification-Electrification-General Electrical Work
Tender Value
2.53 Lakhs
Estimated cost
Bid Submission
18 Sep 2026
2 days left
EMD
6335
Bank guarantee accepted
Document Fee
560
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Lac-Ads-Mla Ads 2025-26 - Vengola Gp - Completion Of Drinking Water Scheme Ward 14 - Pipe Line And Electrification-Electrification-General Electrical Work
BOQ
| Sl. No. | Item Description |
| 1 | Electrification |
| 2 | 90.14.1.1:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame) |
| 3 | 90.14.2.1:Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc. |
| 4 | 90.14.3.1:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardA' section neoprene beeding suitable for 1.60/ 2.00 mm sheet |
| 5 | 90.14.3.2:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardU' section rubber beeding suitable for 1.60/ 2.00 mm sheet |
| 6 | 90.14.6:Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required. |
| 7 | 90.14.7:Supply and providing copper earth bus in the panel board |
| 8 | 90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board |
| 9 | 90.14.10.3:Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL |
| 10 | 90.14.11.1:MCCB AccessoriesSupply and fixing one number earth fault Relay up to 100A with CBCT. |
| 11 | 90.14.11.12:MCCB AccessoriesSupply and fixing shunt release for all voltage range up to 630A. |
| 12 | 90.14.11.14:MCCB AccessoriesSupply and fixing rotary handle, Direct type (including BUC handle with door interlock ) in the existing MCCB of rating up to 250 A |
| 13 | OD120340/2026-2027:Supplying and fixing 63 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole |
| 14 | 2.10.3:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Double pole |
| 15 | OD107995/2026-2027:Supply of 20A HRC Fuse Holder with 5 to 10 Amps fuse links |
| 16 | OD107986/2026-2027:Supply of Blue colour LED indicator, AC/DC, 22.5 mm cut out dia |
| 17 | OD107985/2026-2027:Supply of Red, Green, Black, Yellow, Orange colours LED indicator, AC/DC, 22.5 mm cut out dia |
| 18 | OD107998/2026-2027:Supply and install three numbers of Current Transformer (CT) 100/5 suitable for 3 phase multifunction meter L&T WL440510OOOO or equivalent. |
| 19 | OD107989/2026-2027:Supply and install V, A, F, PF, KW, KVA Multifunction meter 50 - 520 Volts, CT 1/5A, Flush mounting 96x96 mm, Accuracy Class 1.0, 0.5 L&T WL440510OOOO or equivalent. |
| 20 | OD107994/2026-2027:Supply of 1.5 sq. mm ISI marked, FRLS PVC insulated, single core copper conductor cable |
| 21 | 90.6.4.51:Supply and drawing 650/1100 V grade FRLS PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.10.00 sq.mm 1 Run |
| 22 | 90.12.7.42:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp |
| 23 | 9.1.34:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm) |
| 24 | OD108290/2026-2027:Supply, laying and clamping of 50/38 mm Double Walled Corrugated (DWC) pipes made out of HDPE for mechanical protection to underground power / communication / OFC/ Signal cables conforming to IS 14930 Part - II, secure using clamps noted along with the pipe, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 4 sq mm with factory made clamp |
| 25 | OD107983/2026-2027:Internal wiring of MV panel board using 1.5 to 10 Sqmm FRLS cable (Cables not included) using adequate cable terminals, properly dressing and using required cable protection etc, |
| 26 | 90.14.24.4:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.4 KVAr, 3 phase, 440 V, delta connected standard duty Metalised Poly Propylene Cylinderical Capacitor suitable for direct connection to motors. |
| 27 | 90.14.28.6:S & F Motor starters of the following ratingsFully automatic star delta starter for 15HP motor |
| 28 | 90.14.28.10:S & F Motor starters of the following ratingsSubmersible pump controllers with ammeter,DPMCB for single phase 0.5HP submersible motor pumps (DOL) |
| 29 | OD108016/2026-2027:Supply of 15 HP mono block surface pump set, suction/delivery 80x65 mm, 3 Phase, 415 Volts, 2880 rpm, 32 to 50 meters head, 11 to 18 lps discharge, Kirloskar Monobloc Pump KDS/KDI -1555+ or equivalent. |
| 30 | OD108017/2026-2027:Conveyance ,Installation and commissioning of 15 HP mono block motor pump set on the existing concrete foundation, after properly fixing mounting bolts onto the concrete, aligning motor base to the mounting bolts correctly, using required set of nuts and washers, including handling of the pump set, including connecting and terminating the electrical power cables, including installation of HDPE suction pipe and foot valve and test running the pump set satisfactorily, as per OEM specification, ensuring no leakage of water and adequate delivery of pump. |
| 31 | OD108184/2026-2027:Supply of wheel operated cast iron sluice valve, 65 mm flanged, IS 14846, Kartar K 501 Non rising blue. |
| 32 | OD108186/2026-2027:Supply, fabrication, conveyance and fixing 70/80 mm B class GI pipe bent to shape / cut and welded to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required including assembling valves and fittings and supported on wall with concrete as required. |
| 33 | OD108190/2026-2027:Supply and welding MS Slip on flange, 65 mm/9mm PN 16 Butt welding type, to 65 mm medium class GI pipe including finishing, painting and leak checks. |
| 34 | OD108244/2026-2027:Supply of MS Slip on flange, 80 mm/9mm PN 16 Butt welding type |
| 35 | OD108191/2026-2027:Supply of 2-1/2 Inch,65 mm Cast Iron flanged Reflux Valve IS 5312 (Non-Return Valve) with gun metal seating Kartar K 515 |
| 36 | OD108012/2026-2027:Supply of packing sheet |
| 37 | OD108011/2026-2027:Supply of Shellak and Teflon |
| 38 | OD108196/2026-2027:Supply of PVC long bend, 65 mm, PN 10 |
| 39 | OD108208/2026-2027:Supply of 65 mm (2½") PN10 PVC pipe |
| 40 | OD108210/2026-2027:Supply of 65 mm (2½") PN10 PVC tail piece |
| 41 | OD108216/2026-2027:Supply of HDPE tail piece with flange 80 mm, PN10 |
| 42 | OD108217/2026-2027:Supply of HDPE tail piece without flange 80 mm, PN10 |
| 43 | OD108219/2026-2027:Supply of 80 mm PN10 HDPE pipe |
| 44 | OD108226/2026-2027:Supply of 80 mm Cast Iron Foot Valve, Flanged, Kirloskar 80 mm Cast Iron Foot Valve |
| 45 | OD108014/2026-2027:Supply of 12 mm Nylone rope |
| 46 | OD107997/2026-2027:Supply of M16/75 GI Bolt, Nut, washers set |
| 47 | OD108267/2026-2027:Supply and bury M16 × 300 mm J type galvanised MS bolts during concreting, including supply of two each of nuts and washers per bolt. |
| 48 | 14.1:Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres. |
| 49 | 14.12:Providing 15mm thick cement plaster of mix 1:4(1 cement: 4 fine sand) at all levels |
| 50 | 14.7:Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required. |
| 51 | OD108003/2026-2027:Supply installation testing and commissioning of 0.50 HP self-priming single phase motor pump set, Kirloskar MINI JALSENA-II (Gold), 0.5 HP, Single Phase, 220 Volts or equivalent, with suitable length suction and delivery side flexible hose, 25mm foot valve, hose connectors, hose clamp and accessories for priming arrangements. |
| 52 | 90.2.1.1:Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Single Control light point with 6A, plate ceiling rose - Short point |
| 53 | 90.2.1.3:Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FRLS PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (RoHS compliant modular accessories).Single control light point without ceiling rose - Short point |
| 54 | OD108279/2026-2027:Supply, installation, testing and commissioning of prewired LED Bulkhead light fitting, IP 65, 230VAC, 10 Watts, PVC housing with polycarbonate diffuser Philips WT110W LED10S or equivalent, with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. |
| 55 | OD108009/2026-2027:Supply and providing LED bulb 9/12watts Philips/equivalent |
| 56 | 1.58:Supplying and fixing PVC batten/ angle holder including connection etc. as required. |
| 57 | 1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch |
| 58 | 1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet |
| 59 | 1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm) |
| 60 | 1.17.11:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 2.5 sq. mm |
| 61 | 90.6.10.1:Supply and fixing of following sizes of light gauge PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required20 mm |
| 62 | 90.6.10.3:Supply and fixing of following sizes of light gauge PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required32 mm |
| 63 | 5.3:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required. |
| 64 | 5.16:Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 65 | 5.9:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 66 | 90.16.1.1:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.00 mm copper conductor ( 14 SWG) |
| 67 | 90.16.1.2:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG) |
| 68 | 90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG) |
| 69 | 90.16.5.1:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.00 mm (14 SWG) |
| 70 | 90.16.5.2:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG) |
| 71 | 90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG) |
| 72 | OD108007/2026-2027:Supply and providing 25x3 mm brass nut and bolt etc. as required. |
| 73 | 2.3.2:Supplying and fixing following way, single pole and neutral, sheet steel, MCBdistribution board, 240 volts, on surface/ recess, complete with tinned copperbus bar, neutral bus bar, earth bar, din bar, interconnections, powder paintedincluding earthing etc. as required. (But without MCB/RCCB/Isolator)8 way, Double door |
| 74 | 2.12.1:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 75 | 2.10.1:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Single pole |
| 76 | 2.11:Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 77 | OD108005/2026-2027:Supply and install weatherproof, outdoor, SMC meter box with MCB 430x215x150 Sintax GSMB 4422-1 or equivalent on the existing wall bracket near the KSEB post. |
| 78 | OD108013/2026-2027:Supplying and fixing 100A, HRC Fuse Base with HRC Fuse link in the existing SMC meter box complete with connections, testing and commissioning etc. as required. |
| 79 | OD108004/2026-2027:Supplying and fixing 63 amps amps rating, 240/415 volts, neutral link of two poles in the existing Meter box complete with connections, testing and commissioning etc. as required. |
| 80 | OD107987/2026-2027:Preparation of drawings and copies, following up application procedures and liaising to obtain single phase KSEB connections, per pole. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysSep 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender