Tender For Providing Of Structural Steel Lifting Arrangement For Suction Pipes Provided In Drainage Water Collection Sump At Ptt Pump House At Af Stn Car Nicobar And Provisioning Of Wall Embedded Cupboard At Various Location At Af Stn Car Nicobar. 8854/E8
Tender Value
8.50 Lakhs
Estimated cost
Bid Submission
29 Sep 2026
18 days left
EMD
17000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nicobar → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Structural Steel Lifting Arrangement For Suction Pipes Provided In Drainage Water Collection Sump At Ptt Pump House At Af Stn Car Nicobar And Provisioning Of Wall Embedded Cupboard At Various Location At Af Stn Car Nicobar. 8854/E8
BOQ
| Sl. No. | Item Description |
| 1 | Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats conforming to Fe-410W(Gde E-250) quality A complete all as specified and as directed. |
| 2 | Supply and fix Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 290 (Gde-E-165) complete all as specified and directed. |
| 3 | Supply and fix Mild steel, plain, black sheet 1.6mm thick in wall cladding, steel gates, cover to valve pit and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 4 | Supply and fix in repairs mild steel bolts purpose made with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 5 cm and not exceeding 10 cm of shank 16 to 24mm etc complete all as specified and as directed. |
| 5 | M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over two coat of red oxide/Zinc chrome primer complete all as specified and as directed |
| 6 | Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out getting out in soft/loose soil, complete all as specified and as directed. |
| 7 | Removing excavated material (soil) n exc 50 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. |
| 8 | M & L for cutting the hard standing/stone floor (hard/dense soil) complete all as directed by Engr-in-charge. |
| 9 | M&L for making good of road/PCC hard standing by using cement concrete PCC 1:3:6 type C-2 using 40mm graded stone aggregate in filling foundations and mass concrete including plastering and finishing & necessary form work foundation of post complete all as specified and as directed . |
| 10 | M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 11 | Material and labour for reinforced cement concrete design mix M-30 using 20 mm graded granite stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately. |
| 12 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, and similar work, not exceeding 200 mm thick etc, fair finshed surfaces of concrete (Horizontal or sloping) complete all as specified and as directed. |
| 13 | Material and Labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 14 | Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed. |
| 15 | Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of acrylic distemper of approved shade/tint over a coat of primer, over 1mm thick wall care putty finish to achieve uniform smooth surface of wall all as specified and as directed. |
| 16 | Material and Labour for vitrified ceramic tiles 8-10 mm thick polished area of each tiles not exceeding 0.36 sqm of any shade and any pattern (pattern consists combination of two or more tiles ) as in floor etc jointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 15mm thick screed bed in CM 1:6 and pointed in coloured cement to match coloured tiles complete complete all as specified and as directed. . Note:- (i) The colour, shade and pattern shall be approved by the GE during execution work. (ii) No extra cost shall be allowed for Removing and refixing and necesary cutting of door etc if any required during execution of work. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender