Tender For special Repair To Bldg No T-326 (Offr Mess Cook House Of 5089 Coy Asc (Comp) And Provn Of Urinal Point At No. 01 Gate At Delta C Of Dharmund Mil Stn Through Dgrr Wks For The Ft 2026-27 Under Age (I) Bhalra (Nit No. 79 Of 2026-27)
Tender Value
7.43 Lakhs
Estimated cost
Bid Submission
29 Sep 2026
16 days left
EMD
14862
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nagrota → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-326 (Offr Mess Cook House Of 5089 Coy Asc (Comp) And Provn Of Urinal Point At No. 01 Gate At Delta C Of Dharmund Mil Stn Through Dgrr Wks For The Ft 2026-27 Under Age (I) Bhalra (Nit No. 79 Of 2026-27)
BOQ
| Sl. No. | Item Description |
| 1 | Dismanting CGI (corrugated or semi corrugated etc) sheets in roof covering. |
| 2 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 3 | Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles. |
| 4 | Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc all as specified. |
| 5 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame n.exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) all as specified and directed. |
| 6 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 sqm but n.exc 4 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) all as specified and directed. |
| 7 | Demolition of cement concrete (unreinforced) in ground floors and paving's n.exc 15 cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr as specified. |
| 8 | M&L for Machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completeand including 20 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed. |
| 9 | M&L for precast designer coloured Endura tiles with glossy finish (factory made rectified) of size 300mmx300mmx10mm, top layer glazed made in any type of cement and pigment, in required patterns in floor etc set & jointed in neat cement slurry & pointed in white or coloured cement mixed with pigment to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 10 | S & F in repairs MS framed work as in doors or gates of angle iron, door frame or other section with gusset plate, rails, braces and stair case etc complete, drilled for fixing of steel sheeting or other covering etc, to prepared for hanging or sliding with including either hooks and hinges also fastening grills, grating, hold fast of doors and windows chowkat etc, with ends of bars shouldered and or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanksand fixing and similar work confirming to fe 290 Gde E-165 complete all as specified and as directed. |
| 11 | Dismantling of wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets including removal of Debries outside Cantt area complete all as specified and directed by Engineer-in-Charge. |
| 12 | S&F PVC wall panelling made up of PVC hollow panels 25/30cm in width and 10mm thickness interlocking pattern of approved shade and design fixed to wall or ceiling all as specified and directed. |
| 13 | S&F 5mm thick PVC sheet corner fillet of width 35mm for opening wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 14 | M&L False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm of manufacturer M/s Saint Gobain or equivalent of Armstong/Everest including taking down existing ceiling board & grid work etc of any type/pattern complete. |
| 15 | M&L in repair for 17 mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination ,fixed with screws to timber frame work, complete all as specified and directed. |
| 16 | M&L for wrought second class hardwood in scantling, complete all as specified and directed |
| 17 | S & F for PVC cupboard shelf/ partition/ frame / shutter of 18mm thick side of panel externally impact perfact finish to the shutter and joined together with solvent cement adhesive 8mm thick (4mmx2)x12mm wide PVC sheet is used as gap insert for top & bottom rail, 18mm x 1mm PVC edge lipping is done on top & bottom side using PVC solvent cement adhesive, incl hasp and stable for locking purpose, etc complete as per direction of Engr-in-charge, manufacture's specification and drawing. |
| 18 | M&L for two coat of synthetic enamel paint tint after preparation of new surfaces of steel of any description and priming the surface with red oxide, exc 10cm in width or girth when unconnected with other painting or when painted in a different tint. |
| 19 | M&L for preparation of old painted steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint all as specified and directed. |
| 20 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. having minimum thickness of powder coating 50 micron incl taking down complete all as specified and directed. |
| 21 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl Powder Coating of minimum thickness of powder coating not less than 50 micron complete all as specified and directed. |
| 22 | Supply only Sheet glass 4.8mm thick ,ordinary quality fixed with aluminium beading and rubber gaskeet n exc 0.50 sqm each. all as specified and directed. |
| 23 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples |
| 24 | S & F Pressed steel frames for doors of size 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. incl filling and compacted PCC 1:3: 6 (20 MM aggregate) complete as specification all as specified and directed. |
| 25 | S&F for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 26 | S&F 2nd class hardwood glazed and skeleton door shutters 35mm thick , open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats |
| 27 | S&F Alluminium, anodized, barrel tower bolts 150mm extruded section. |
| 28 | Supply and fixing aluminium alloy sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia and including a minimum of 6 bolts and nuts,four on bolt type and two on staple plate 250 mm long complete all as specified and directed by Engineer-in-Charge. |
| 29 | Supply and fixing floor door stopper 150mm length of cover plate of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F 300 mm long mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed. |
| 31 | M & L for 10 mm thick rendering on fair faces or brick work or concrete surfaces in cement mortar 1:6 surface finished even and smooth (with out using extra cement) |
| 32 | Preparation of old plastered surface including filling of small holes etc. and applying two coat of cement based paint complete all as specified and directed by Engr-in-Charge. |
| 33 | M & L for preparation of old decorated plastered surfaces of walls including corrices by washing ,rubbing down and stopping of distempered surfaces of walls and applying one coat of oil bound distemper white or tinted complete all as specified and directed. |
| 34 | M&L for Cement concrete B1 1:2:4 (20mm aggregate) in foundations, filling and mass concrete |
| 35 | S & F in repair Providing precast cement concrete type B0 1:2:4 (12.5mm aggregate)louvres and jallies, 25mm thick (mea sured solid), including all mould- ings, set in cement mortar 1:4 |
| 36 | S& F in repair Rotational moulded Polyethylene water storage tank 500 liters capacity (cylidrical vertical with closed top) hoisted and fixed in position all as specified in SSR part incl dismantling water tank. |
| 37 | M&L for stain less steel plate rack for kitchen 1 mm thick of best quality with suitable hanging arrangement and fixed to wall complete all as specified and as directed by Engineer-in-Charge.Note:- Size of plate rack should not be less than 900x1000 mm. |
| 38 | Taking up or down 15 mm dia old serviceable / unserviceable steel tubing any grade and connections cleaning for re-fixing or removal to store complete all as specified and directed . |
| 39 | All as per item no 48 above but 20mm bore complete all as specified and as directed. |
| 40 | M&L Plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor or paving 75mm thick,all as specified. |
| 41 | M&L for surface excavation nexc 30cm deep and averaging 15cm deep in hard dense soil and getting out etc complete all as specified and directed. |
| 42 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation or etc, for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard dence soil, complete all as specified and directed. |
| 43 | M&L for PCC 1:4:8 type D2, using 40mm graded stone aggregate, as in foundation filing, and mass concrete , etc complete all as specified and directed |
| 44 | M & L for Brickwork with subclass `B' bricks, straight or curved on plan exc 6 m mean radius in cement mortar 1:4 |
| 45 | M&L for Plain cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregates as in copings etc. and in similar works including weathering,slightly rounded or chamfered angles and throating and necessary form works,all as specified. |
| 46 | M&L for RCC 1:2:4 type B1 using 25 mm graded stone aggregate for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. |
| 47 | M & L for formwork to flat fair finished surface for sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter finished fair complete all as specified and directed |
| 48 | M&L for RCC 1:2:4 type B1 using 25 mm graded stone aggregate for Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed. |
| 49 | M & L for formwork flat fair finished surfaces to sides and soffits of floor or roof beam, beam hauchings, bands, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc complete all as specified and directed |
| 50 | M&L for Pre-cast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cover slab fixed in position including necessary form work and set in CM 1:6 |
| 51 | M & L high strength steel deformed TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping columns,hookings ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips, etc complete all as specified and directed. |
| 52 | M&L for Mild steel bars (TMT bars) 5mm dia and over upto and including 10mm dia in strriups,spacers and binders complete all as specified and directed. |
| 53 | M & L for hardcore of guage exc 63 mm but n.exc 100 mm deposited spread and levelled in layers n.exc 15 cm thick watered and rolled/rammed to a true surface with broken bricks. |
| 54 | M&L Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor or paving 75mm thick,all as specified. |
| 55 | M&L for 40 mm thick plain cement concrete 1:2:4 type B-1 ( using 25 mm graded stone aggregate) finished even and smooth as top of floors, complete all as specified and directed. |
| 56 | M&L for Rendering 15 mm thick cement plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces of wall and to be finished even and smooth without using extra cement all as specified. |
| 57 | M&L for Rendering 15 mm thick cement plaster in cement mortar (1:4) on other than fair faces of brick work and surfaces to be finished even and smooth without using extra cement all as specified.(incl all necessary scaffolding, lifting arrangement) |
| 58 | M&L two coats of cement based paint on newly plastered surface including preparation. |
| 59 | M & L for preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant cement primer and over a coat of putty complete all as specified and directed. |
| 60 | M & L for Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed . |
| 61 | M & L for Glazed ceramic coloured tiles of size 450mmx300mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed. |
| 62 | S&F Pre -painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. |
| 63 | S&F Pre -painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. |
| 64 | S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, hollow pipe or flat sections) including distance pieces, cleats etc.complete all as specified and directed. |
| 65 | Painting to steel surfaces of any description over 10 cm in width or girth not otherwise described for two coat of synthetic enamel paint over a coat of red oxide, zine chrome. |
| 66 | M&L 75 mm thick PCC type C2 1:3:6 (40mm graded aggregate) as in Plinth protection filled with mastic filling and 10 mm wide joints between the walls and plinth protection shall be filled with mastic filling complete all as specified. |
| 67 | Supplied and fixed Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including fixing of inlet, outlet & over flow pipe etc complete all as specified and as directed. |
| 68 | Excavation in post holes (or similar holes) each n.exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth aroud in layers not exceeding 25 cm with soft/loose soil. |
| 69 | M & L for cement concrete in foundation filling, subbase and mass concrete type C2 1:3:6 (40 mm graded aggregate) |
| 70 | Supply and fixing medium grade 20mm bore galvanized tubing with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply and fixing medium grade 15mm bore galvanized tubing with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 72 | S&F 15 mm dia gun - metal globe or gate valves with iron wheel head ,screwed both ends for iron pipe and fixed |
| 73 | S&F 20 mm dia gun - metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed |
| 74 | S&F in repairs CP bib taps long body , cast copper alloy, fancy type with crutch or butterfly handles, chromium plated, screwed down to iron pipes or for brass ferrule of 15 mm bore complete all as specified and directed. |
| 75 | S&F in repair CP angle or plain stop valves, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed. |
| 76 | S&F in repairs vitreous china wash hand basin white flat back of size 550x400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified. Make- Commander / Cera / Parryware |
| 77 | Supply & fixed ,Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings, complete all as specified and directed. |
| 78 | S&F in repairs 15mm dia PVC Connection 450 mm long with brass nuts complete all as specified and as directed. |
| 79 | S & F in repairs PVC (SWR) nani trap / floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and as directed. |
| 80 | Supply and fixing of soap-dish chromium plated all as specified and directed. |
| 81 | S&F in repairs of brass CP tubular towel rail 20 mm dia 60cm long between flange with brackets etc as in repair complete all as specified and directed. |
| 82 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 83 | S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed. |
| 84 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. |
| 85 | S&F 100 mm long mild steel butt hinges, cold rolled, medium weight complete all as specified and directed. |
| 86 | S&F for 125mm long anodised aluminium barrel tower bolt of extruded section complete all as specified and directed. |
| 87 | S&F 150mm long anodised aluminium handles, cast type complete all as specified and directed. |
| 88 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed |
| 89 | S & F 75 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 90 | S&F 75mm bore PVC (SWR) bends any radius complete all as specified and as directed. |
| 91 | S & F 75mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls / floor or in trenches complete all as specified and as directed. |
| 92 | Returing, filling in trenches, incl spreading, levelling, watering and well ramming in layers not exc 25 Cm in hard/dense soil complete all as specified and directed. |
| 93 | Removing excavated material (soil) to a distance not. exc. 50 mtr and depositing where directed at a level nexc 1.5 mtr above the starting point complete all as specified and directed. |
| 94 | S&F Chequered cement concrete tiles 30cm x 30cm x 25mm thick,set, jointed with grey cement and no pigment,pointed in neat cement slurry in floor including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed . |
| 95 | M&L plain cement concrete 1:4:8, type D2( using 40mm graded stone aggregate) 75mm thick as in sub base of floor complete all as specified and directed . |
| 96 | M&L for PCC 1:2:4 type B1 using 25 mm graded stone aggregate for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. |
| 97 | Taking down old point wiring complete for light/fan/socket(5/15 Amps) bell point etc complete with all light fittings accessories, such as switch sockets 5/15 Amps ceiling rose etc including making good to the disturbed surface to match with the existing complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 98 | Taking down old point wiring complete for light/fan/socket(5/15 Amps) bell point etc complete with all light fittings accessories, such as switch sockets 5/15 Amps ceiling rose etc including making good to the disturbed surface to match with the existing complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysOct 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender