Tender For Special Repair And Maintenance Of Veterinary Staff Residences At Dalhousie, Distt. Chamba (Hp).
Tender Value
19.44 Lakhs
Estimated cost
Bid Submission
18 Sep 2026
2 days left
EMD
39000
Bank guarantee accepted
Document Fee
600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chamba → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair And Maintenance Of Veterinary Staff Residences At Dalhousie, Distt. Chamba (Hp).
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling Galvanized Steel (G.S.) Sheet roofing including ridges, hips, valleys and gutters etc., and stacking the serviceable material separately and unserviceable material at designated locations under all leads, complete in all respects as per the directions of the Engineer-in-Charge. |
| 2 | Dismantling cement asbestos, wooden, or other hardboard ceiling or partition walls, including sorting and stacking of serviceable materials separately, and disposal of unserviceable materials at designated locations under all leads, complete in all respects as per the directions of the Engineer-in-Charge. |
| 3 | Demolishing stone rubble masonry in cement mortar manually or by mechanical means, including sorting and stacking of serviceable materials separately, and disposal of unserviceable materials at designated locations under all leads, complete in all respects as per the directions of the Engineer-in-Charge. |
| 4 | Demolishing nominal cement concrete of mix 1:4:8 or leaner (including equivalent design mix) manually or by mechanical means, including disposal of unserviceable material at designated locations under all leads, complete in all respects as per the directions of the Engineer-in-Charge. |
| 5 | Dismantling wood work in frames, trusses, purlins, and rafters up to 10 metres span and 5 metres height, including sorting and stacking of serviceable materials separately, and disposal of unserviceable materials at designated locations under all leads, complete in all respects as per the directions of the Engineer-in-Charge. (a) of sectional area 40 square centimetres and above |
| 6 | (b) Of sectional area below 40 square centimetres |
| 7 | Dismantling doors, windows, and clerestory windows (steel or wood) shutters, including chowkhats, architraves, holdfasts etc., complete, and stacking the serviceable material separately and unserviceable material at designated locations under all leads: Of area 3 square metres and below. |
| 8 | Earth work in excavation by mechanical means (Hydraulic excavator) or manual means in foundation trenches or drains , including dressing of sides and ramming of bottoms, lift up to all leads, including getting out the excavated soil and disposal of surplus excavated soil at designated locations under all leads, in all kinds of soil, complete in all respects as per the directions of the Engineer-in-Charge. |
| 9 | Providing and laying in position cement concrete of specified grade, excluding the cost of centering and shuttering – All work up to plinth level 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), including curing and carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 10 | Providing and laying brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand), including curing and carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 11 | Providing and fixing centering and shuttering including strutting, propping etc. and removal of form work after completion of work, including carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of the Engineer-in-Charge. (a) Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 12 | Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc |
| 13 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. |
| 15 | Providing and laying brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in Superstructure in cement mortar 1:6 (1 cement : 6 coarse sand), including curing and carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 16 | Providing and fixing Japani sheet steel window/ Door frame fabricated from 16-gauge (1.5 mm) mild steel sheet, pressed and bent to standard profile, including cutting to required lengths, welding, grinding, fixing in position with hold fasts or lugs, complete with MS glazing clips and necessary screws, etc., including priming coat but excluding cost of glazing and painting. The frame shall be fabricated as per standard specifications and fixed in masonry with cement mortar 1:3 (1 cement: 3 coarse sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (A) 125 X 60 X 40 MM Double Rebate |
| 17 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part-I), decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters, 35 mm thick, including ISI marked stainless steel butt hinges with necessary screws, including carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 18 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) including carriage of material with in all lead and lifts. For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 19 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 20 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)including carriage of material with in all lead and lifts |
| 21 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete including carriage of material with in all lead and lifts. |
| 22 | Providing and fixing bright finished brass hard drawn hooks and eyes 150 mm including carriage of material with in all lead and lifts. |
| 23 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material with in all lead and lifts. (a) 100 mm |
| 24 | (b) 125 mm |
| 25 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 250x16 mm including carriage of material with in all lead and lifts. |
| 26 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. Complete including carriage of material with in all lead and lifts. (a) 100x10 mm |
| 27 | (b) 150x10 mm |
| 28 | Providing French spirit polishing Two or more coats on new works including a coat of wood filler including carriage of material with in all lead and lifts. |
| 29 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, with necessary accessories and screws etc. complete including carriage of material with in all lead and lifts. |
| 30 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 31 | Providing and applying 15 mm thick cement plaster on rough side of single or half brick wall in cement mortar 1:6 (1 cement : 6 fine sand), including curing, scaffolding and carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 32 | Providing and fixing precoated galvanised iron profile sheets (TATADURASHINE) (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to required size and shape, carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of |
| 33 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete Ridges plain (500 - 600mm) including carriage of materials through all modes of transportation within all leads and lifts, complete as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 34 | Providing and fixing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, complete in all respects, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 35 | Providing and fixing M.S. B.P. sheet 1.66 mm to 2 mm thick in eaves board/fascia/soffits/ceiling, including cutting, fixing and welding to steel roof members and applying a coat of red lead primer, complete in all respects, excluding the cost of base members of steel work which shall be measured and paid separately, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 36 | Providing and fixing wooden plank ceiling with 12 mm thick 1st class deodar wood planks overlapping each other and jointed with wood screws, complete in all respects, excluding the cost of frame work which shall be measured and paid separately, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 37 | Providing and fixing plain multipurpose cement board (high pressure steam cured) in ceiling etc. with suitable screws for cement particle board, complete in all respects, excluding the cost of frame work which shall be measured and paid separately, using 6 mm thick cement fibre board conforming to IS:14862, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 38 | Providing and laying vitrified floor tiles of size 600 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg per sqm including grouting the joints with white cement and matching pigments etc., complete in all respects, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 39 | Dismantling tile work in floors and roofs laid in cement mortar, including stacking of serviceable material, for thickness of tiles 10 mm to 25 mm, complete in all respects as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 40 | Providing and laying heavy duty exterior anti-skid vitrified floor tiles of approved make, colour, shade and size 400×400 mm and thickness not less than 9 mm in floor over 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement mixed with matching pigment, cutting, polishing, finishing and curing etc. complete in all respects as directed by the Engineer-in-Charge. |
| 41 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours as approved by Engineer in charge, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete in all respects, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 42 | Providing and fixing Ist quality ceramic glazed/ digital wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete in all respects, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 43 | Providing and fixing door shutters made with 1 mm thick M.S. sheet, reinforced with 30 x 6 mm M.S. flats for diagonal braces and central cross piece, including M.S. angle iron frame of size 40 x 40 x 6 mm and 3 mm thick M.S. gusset plates at junctions and corners, welded and fixed in position with all necessary fittings and fixtures complete, including cutting, welding, grinding, applying one coat of approved steel primer, carriage of materials through all modes of transportation within all leads and lifts, complete in all respects as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 44 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc. including carriage of materials through all modes of transportation within all leads and lifts, complete in all respects as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 45 | Providing and fixing 4mm thick ACP Sheet in all coloures approved by Enginner in charge fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge including carriage of materials through all modes of transportation with in all leads and lifts. |
| 46 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of walls in cement mortar 1:4 (1 cement : 4 fine sand), including disposal of unserviceable material/debris, carriage of materials through all modes of transportation within all leads and lifts, complete in all respects as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 47 | Providing and applying two or more coats of synthetic enamel paint of approved brand and manufacture on new work to give an even shade, including preparation of surface complete, carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 48 | Removing white or colour wash by scraping and sand papering and preparing the surface smooth, including necessary repairs to scratches etc., complete in all respects, including disposal of unserviceable material/debris, carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 49 | Providing and applying white cement based putty of approved brand and manufacturer over plastered wall surface to an average thickness of 1 mm to prepare the surface even and smooth, complete in all respects, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 50 | Providing and applying oil bound washable distemper of approved brand and manufacture to give an even shade on new work, two or more coats over and including water thinnable priming coat with cement primer, complete in all respects, including preparation of surface, carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 51 | Providing and fixing interior PVC Wall Panelling of approved make and shade, consisting of hollow-core interlocking panels (minimum thickness 8mm to 10mm), fixed directly to the existing wall surface using heavy-duty adhesive or direct fasteners in perfect plumb and alignment. Item includes surface cleaning, necessary cutting, and all essential PVC accessories (starters, corners, and edge profiles) to provide a finished look. Rate includes all materials, labor, tools, and scaffolding complete in all respects as per the directions of the Engineer-in-Charge. |
| 52 | Providing and applying two or more coats of acrylic emulsion paint of approved brand and manufacture on new work to give an even shade, including preparation of surface complete, carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 53 | Providing and fixing special quality bright finished brass cupboard or wardrobe locks with four levers of approved quality, 50 mm size, including necessary screws etc., complete in all respects, including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 54 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 55 | Providing and fixing high pressure PVC spigot and socketwaste and ventilating pipes ISI marked confroming to IS : 13592 Type A, i/c fixing with approved adhesive etc. complete. 110mm diameter including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 56 | Providing and fixing on wall face PVC accessories rain water pipes including filling the joints with approved adhesive complete 110mm diameter including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. (a) plain Bend 110 mm |
| 57 | (b) Single tee without door |
| 58 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall 20 mm nominal outer dia Pipes |
| 59 | Providing and fixing PVC floor trap ISI marked of self cleaning design i/c fixing with approved adhessive cost of cutting and making good the wall and floors etc. 110mm x 90mm including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 60 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 61 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 62 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 63 | Poviding and fixng vitrous china pedestal for wash basin complete recessed at the back for reception of pipe and fittings including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 64 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 65 | Providing and fixing 100m stainless steel grating forgully,foor or Nahani trap including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 66 | Providing and fixing 600x450mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screw and washers including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 67 | Providing and fixing PTMT towel rail complete with CP brass brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 68 | Providing and fixing CP brass bib tap with capastan head 15 mm dia including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 69 | Providing and fixing CP stop cock 15mm dia including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 70 | Providing and fixing PVC connection pipe with brass unions 45 cms length 15mm nominal size including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. |
| 71 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms including carriage of materials through all modes of transportation within all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysSep 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender