Tender For Repairs To Quarter No. D-6 For Officer Accommodation At Mtpf Avnl Ambernath.
Tender Value
31.69 Lakhs
Estimated cost
Bid Submission
21 Sep 2026
11 days left
EMD
63380
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thane → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Quarter No. D-6 For Officer Accommodation At Mtpf Avnl Ambernath.
BOQ
| Sl. No. | Item Description |
| 1 | Repairs to Quarter No. D-6 for Officer Accommodation at MTPF AVNL Ambernath. |
| 2 | Taking down cement or cement lime plaster any description including raking out joints, hacking for key, scrubbing down with water, complete cleaning of site & removal of all rubbish outside premises & spreading, leveling in low lying area, etc all complete as directed by the EIC. |
| 3 | Dismantling of single layer Mangalore pattern or similar tiles in roofing including proper stacking of dismantled mangalore tiles neatly at earmarked location, thorough cleaning of site & removal of all rubbish outside premises & spreading, leveling in low lying area, etc all complete as directed by the EIC. |
| 4 | Dismantling of Battens for tiles, shingles etc, of any size spaced Exc 15 cm including tilting fillets including proper stacking of dismantled battens neatly at earmarked location, thorough cleaning of site & removal of all rubbish outside premises & spreading, leveling in low lying area, etc all complete as directed by the EIC. |
| 5 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings including proper stacking of dismantled sheets neatly at earmarked location, thorough cleaning of site & removal of all rubbish outside premises & spreading, leveling in low lying area, etc all complete as directed by the EIC. |
| 6 | Taking up or down steel tubing and connections 15 mm bore dia of pipe and above, including cleaning for refixing or removal to store, etc all complete as directed by Engg in Charge. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises & spreading, leveling in low lying area, etc all complete as directed by EIC. |
| 8 | Demolition in Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) & removal of all rubbish outside premises & spreading, leveling in low lying area, etc all complete as directed by EIC |
| 9 | M & L for dismantling of brick work or stone masonry including thorough cleaning of site & removal of all rubbish outside the premises & spreading, leveling in low lying area, etc all complete as directed by the EIC. |
| 10 | Dismantling wrought iron or mild steel work of any description including neatly stacking the dismantled material in the earmarked space, etc all complete as directed by the EIC. |
| 11 | Taking down shutters exc 2 Sq.m each and removing to store etc all complete as directed by the EIC. |
| 12 | Resecuring without taking down Chowkhats or frames exc 1.5 sq.m each & n Exc 4 Sq.m each including securing fittings, etc. which have become partly loosened but which can be secured with holdfasts, plugs, etc. all complete as directed by the EIC. |
| 13 | M & L for Taking down chowkhats or frames exc 1.5 sq.m each & n Exc 4 Sq.m each including removing to store, etc all complete as directed by the EIC |
| 14 | M & L for Taking down chowkhats or frames n exc 1.5 sq.m each including removing to store, etc all complete as directed by the EIC. |
| 15 | M & L for Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed in 1st class hardwood, etc all complete as directed by the EIC.Note: sample of all material/s of 1st class hardwood shall be got approved from the EIC. |
| 16 | M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified etc including removing of old water proofing treatment, etc all complete as directed by EIC (Make: Tiki dan / Pidilite). Note: The sample of all related material/s of waterproofing membrane shall be got approved from EIC before Starting of the Work |
| 17 | S & F GI wire netting 0.9 mm dia and 12 mm mesh lathing in ceiling, columns, beams etc including all laps, cutting & wastes, all scaffolding arrangements, screws & washers for fixing the netting on ceiling or any other surface, etc all complete as directed by the Engg In Charge.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 18 | M & L for application of passivating coat over exposed steel reinforcement including following procedure:(i) Surface preparation: Surface of reinforcement shall be cleaned by wire brushing; all loose scales, dirt etc shall be removed.(ii) Application of passivating coat: Mix. OPC with the Acrylic Polymer Modifier (Make: Roff Supercrete / Dr. Fixit Pidicrete WP / any other equivalent make approved by the Engg in Charge) in a ratio of 1:2(i.e.1 Kg of chemical mixed with 2 Kg of OPC), The OPC & chemical shall be thoroughly mixed to form uniform slurry & to be applied with paint brush in two coats.The Contractor shall arrange for safe working scaffolding, ladders etc at his own risk& cost, etc all complete as directed by the Engg in Charge.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 19 | M & L for application of bonding coat between concrete & mortar for ceiling plastering including following procedure:(i) Mix OPC 1.75 Kg with 1.75 Kg of sand & 1 Litre of Acrylic Polymer Modifier (Make: Roff Supercrete / Dr. Fixit Pidicrete WP / Any other equivalent make approved by the Engg in Charge) (ii) The ceiling surface shall be properly hacked for receiving of bond coat to the entire satisfaction of the Engg. in Charge.(iii) The mixed mortar / slurry shall be applied to all ceiling surface by brush.(iv) The plaster coat shall be started when the bond coat is still tacky.(v) The plastering coat shall be completed within 45 minutes of application of bond coat.(vi) The Contractor shall follow all safety procedures, safe scaffoldings.(vii) The Contractor shall show the bond coat applied surface to SIC / EIC for verification. The entry in this regard shall be endorsed in the Works Diary by the SIC / EIC,etc all complete as directed by the Engg in Charge.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 20 | M & L for grouting 25 mm thick under stanchion bases or grillages, etc. including any temporary shuttering to edges with cement mortar 1:2, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 21 | M & L for TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 22 | M & L for rendering average 20 mm thick cement plaster which shall be applied in Two Coats on fair faces of brickwork or concrete or stone masonry surface in patch works as per requirement, matching the existing finished surface, in cement mortar 1:4 with sand faced finish plaster including addition of waterproofing compound as per manufacturer's instructions, use of safe scaffolding for working, complete cleaning of site, curing for not less than 14 days, removal of all rubbish outside factory premises, etc all complete as directed by Engg in Charge.Note: (i) Contractor shall use only clean river sand / washed snad for preparation of cement mortar in proportion 1:4 i.e. one part of cement mixed with 4 parts of clean river sand / washed sand (ii) The cement to be used shall not be more than one month old.(iii) Any one of the make of cement shall be used throughout the work from M/s Ambuja , M/s Ultratech, M/s Birla, M/s ACC(iv) The Plaster shall be applied in Two Coats of 10 mm thick each coat. Hacking shall be done over 1st coat of plastering to receive second coat (v) Sample of all materials shall be got approved from the EIC before use in work. |
| 23 | Supply of Integral Liquid waterproofing compound, etc all complete as directed. (Make: Dr. Fixit / Roff Chemicals / Sunanda Speciality Coatings).Note: The sample of all material/s of waterproofing compound shall be got approved from the EIC before use in work. |
| 24 | M & L for rendering average 15 mm thick cement plaster which shall be applied in Two Coats on fair faces of brickwork or concrete or stone masonry surface on wall in patch works as per requirement, matching the existing finished surface, in cement mortar 1:4, including neeru finish to the plastered surface, use of safe scaffolding for working, complete cleaning of site, curing for not less than 14 days, removal of all rubbish outside factory premises, etc all complete as directed by Engg in Charge.Note: (i) Contractor shall use only clean river sand / washed sand for preparation of cement mortar in proportion 1:4 i.e. one part of cement mixed with 4 parts of clean river sand / washed sand (ii) The cement to be used shall not be more than one month old.(iii) Any one of the make of cement shall be used through out the work from M/s Ambuja , M/s Ultratech, M/s Birla, M/s ACC(iv) The Plaster shall be applied in Two Coats of 10 mm thick each coat. Hacking shall be done over 1st coat of plastering to receive second coat v) The sample of all related materials shall be got approved from EIC before use in work. |
| 25 | M & L for rendering average 10 mm thick cement plaster on fair faces of brickwork or concrete surface in Ceilings in patch works as per requirement, matching the existing finished surface, in cement mortar 1:4, including neeru finish to the plastered surface, use of safe scaffolding for working, complete cleaning of site, curing for not less than 14 days, removal of all rubbish outside factory premises, etc all complete as directed by Engg in Charge.Note: (i) Contractor shall use only clean river sand / washed sand for preparation of cement mortar in proportion 1:4 i.e. one part of cement mixed with 4 parts of clean river sand / washed sand (ii) The cement to be used shall not be more than one month old.(iii) Any one of the make of cement shall be used through out the work from M/s Ambuja , M/s Ultratech, M/s Birla, M/s ACCiv) The sample of all related materials shall be got approved from EIC before use in work. |
| 26 | M &L for brickwork in sub class 'B' bricks in CM 1:6, etc all complete as directed by the EIC.Note: The sample of all related materials shall be got approved from EIC before use in work. |
| 27 | M & L Rendering 15 mm thick cement plaster in 1:4 on fair faces of brick work or concrete surfaces including making plastered surface rough for receiving tiles, removing rubbish off the premises, etc all complete as directed by EIC.Note: (i) Contractor shall use only clean river sand / washed sand for preparation of cement mortar in proportion 1:4 i.e. one part of cement mixed with 4 parts of clean river sand / washed sand (ii) The cement to be used shall not be more than one month old.(iii) Any one of the make of cement shall be used throughout the work from M/s Ambuja , M/s Ultratech, M/s Birla, M/s ACCiv) The sample of all related materials shall be got approved from EIC before use in work. |
| 28 | S&F Glazed ceramic coloured tiles (Make: HR Johnson / Kajaria / RAK Ceramics) in vertical surface 450X 300 of standard thickness as per manufacturer, set and jointed in neat cement slurry and pointed in white or colour cement to match, etc all complete as directed by EIC Note: Sample, design, pattern etc shall be got approved from EIC before execution of work |
| 29 | M&L for broken stone Hardcore of gauge n exc. 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true surface, etc all complete as directed by EIC |
| 30 | M & L for Cement concrete of Type B2 1:2:4 (40 mm graded aggregate) with roughhening of surface with brooming while the concrete is fresh where directed as in plinth protection work, etc all complete as directed by EIC. |
| 31 | M&L for Screed bed or bedding layer of mortar 40 mm average thick, CM 1:4 for laying floor finishes, etc all complete as directed by EIC |
| 32 | S&F Non - skid Ceramic coloured tiles (Make: HR Johnson / Kajaria / RAK Ceramics) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, etc all complete as directed by EIC Sample, design, pattern should be get approved by EIC before execution of work |
| 33 | M&L Granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc all complete as directed by EIC.Note: Sample shall be got approved from EIC before execution of work |
| 34 | S & F Machine cut kudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, etc all complete as directed by EIC.Note: Sample shall be got approved from EIC before execution of work |
| 35 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, etc all complete as directed by the EIC.Note: Sample work shall be got approved from EIC before execution of work |
| 36 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and provision of fittings like hings, tower bolts, handles etc for smooth operation of shutters wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.Note: Sample shall be got approved from EIC before execution of work |
| 37 | S&F 4mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, etc all complete as directed by EIC.Note: Sample shall be got approved from EIC before execution of work |
| 38 | S & F Prelaminated particle board 9mm,exterior grade, prelaminated both sides with decorative choice lamination fixed with screws, etc all complete as directed by EIC.Note: (i) Sample of all materials shall be got approved from the EIC before use in work.(ii) for Washroom doors equivalent water proof material of required thickness shall be used after prior approval from the EIC. |
| 39 | M & L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth etc all complete as directed by EIC |
| 40 | M & L for Excavating in trenches in Hard dense soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out, etc all complete as directed by the EIC |
| 41 | M & L for Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm, etc all complete as directed by the EIC |
| 42 | S & F of Tubes, 'Medium Grade', galvanised, with all fitting; laid in trenches 25 mm dia etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 43 | M & L for Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 20 mm etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 44 | S & F Unplasticised PVC pipes 20 mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., including all pipe fittings, fixtures required for connections (Make: Prince 'Easyfit\\" / Astral \\"Aquaris\\" / Finolex UPVC pipes as approved by EIC / Birla UPVC Pipes as approved by EIC) etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 45 | S & F Unplasticised PVC pipes 15 mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc, including all fittings / fixtures required for connections (Make: Prince 'Easyfit\\" / Astral \\"Aquaris\\" / Finolex UPVC pipes as approved by EIC / Birla UPVC Pipes as approved by EIC), etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 46 | Supplying and laying of CPVC pipes (of Approved Make from Prince / Astral / Supreme / Finolex) SDR 11 & plain CPVC SDR 11 fittings for 25 mm outer dia of pipe including on walls/ceiling or laying in floors complete, all as specified & directed by the Engg in Charge.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 47 | S&F Male Brass Threaded Adaptor (MTA/ MBTA) (of Approved Make from Prince / Astral / Supreme / Finolex) for CPVC pipe of 25 mm outer diameter, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 48 | S&F Female Brass Threaded Adaptor (FTA/ FBTA) (of Approved Make from Prince / Astral / Supreme / Finolex) for CPVC pipe of 25 mm outer diameter, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 49 | S&F Brass Elbow for CPVC pipe of 25 mm outer diameter (of Approved Make from Prince / Astral / Supreme / Finolex), etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 50 | S&F Brass Tee for CPVC pipe of 25 mm outer diameter (of Approved Make from Prince / Astral / Supreme / Finolex) etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 51 | S & F fancy type chromium plated bib taps (Make: Jaquar / Hindware / Plumber) for 15 mm dia pipe of cast copper alloy with crutch handle, screwed down for iron pipe or for brass ferrule and fixed (minimum weight of one fancy bib tap shall be 0.575 Kg ) etc all complete as directed by Engg in Charge.Note: Sample shall be got approved from EIC before fixing. |
| 52 | S & F stop valves, cast copper alloy, fancy type chromium plated (Make: Jaquar / Hindware / Plumber) with long shank & cup (concealed type) for 15 mm dia pipe with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed (minimum weight of one tap shall be 0.575 Kg ) etc all complete as directed by Engg in Charge.Note: Sample shall be got approved from EIC before execution of work |
| 53 | S & F of PVC connections 15 mm size 300 mm long, etc all complete as directed by the Engg in Charge.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 54 | S & F Hot water pipe duly insulated with glass wool and aluminium cladding 15 mm bore, etc all complete as directed.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 55 | S & F Brass Chromium plated shower roses 125 mm with or without swivel joints, any size, including fixing to steel pipe or union, etc all complete as directed by EIC. Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 56 | S & F PVC (SWR) multi floor trap 75 mm dia and above with grating including jointing with solvent cement, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 57 | M & L 150mm Sail-glazed stoneware drain pipes laid in trenches and jointed as specified ,etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 58 | S & F PVC (SWR)110mm pipes (Make: Prince / Supreme / Finolex) single socketed, in any length with rubber ring joints, laid in trenches or in floors including taking down old pipe etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 59 | S & F PVC (SWR) bends 110mm any radius (Make: Prince / Supreme / Finolex) including taking down old, etc all complete as directed by Engg-in-Chrage. Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 60 | M & L 150mm Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested built in 1:3:6 type C-2, etc all complete as directed by EIC. |
| 61 | S & F Vitreous China wash basin, white, flat back, size 550x400mm (or equivalant size as approved by the EIC) (Make: Hindware / Parryware / Plasto) including brackets including cutting for and pinning in ends of brackets or erecting stand, all required fittings such as waste coupling, waste pipes, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 62 | S & F of Pillar taps (Make: Jaquar / Hindware / Parryware) for 15 mm bore dia of pipe, Fancy Type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 63 | S & F of sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarfwall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 64 | S & F Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. 40 mm with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 65 | S & F High density polyethylene pipes 40 mm bore dia minimum (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors, etc all complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 66 | S & F of vitreous china premium/ 1st quality wash down water closet (Make: Hindware / Parryware / Plasto) wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc). also including PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets & flush pipe, also including Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified, etc all as specified and complete as directed by EIC.Note: Sample of all materials shall be got approved from the EIC before use in work. |
| 67 | S & F of 600mmx450mm bevelled edge mirror of selected quality glass (Make: Saint Gobain / Modi Glass / Asahi Float Glass), mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, etc all complete as directed by Engg in Charge.Note : Sample of mirrors shall be got approved from EIC before fixing. |
| 68 | S & F gun metal globe or gate valves Heavy Duty with ISI Mark for 25 mm bore dia of pipe, with iron wheel head or PVC coated lever screwed both ends for pipes of standard quality, etc all complete as directed by the Engg In Charge. Note: Sample shall be got approved from EIC before fixing. |
| 69 | S & F gun metal globe or gate valves Heavy Duty with ISI Mark for 15 mm bore dia of pipe, with iron wheel head or PVC coated lever screwed both ends for pipes of standard quality, etc all complete as directed by the Engg In Charge. Note: Sample shall be got approved from EIC before fixing. |
| 70 | S & F Tubular towel rail Brass Chromium plated, 20mm dia (or equivalent dia as per prescribed make & approved by EIC), D type, 60cm long between flanges with all accessories, etc all complete as directed by the Engg in Charge.Note: Sample of Towel rail with all accessories shall be got approved from EIC before fixing. |
| 71 | S & F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed with all accessories, etc all complete as directed by the Engg in Charge.Note: Sample of Toilet paper holder with all accessories shall be got approved from EIC before fixing. |
| 72 | S & F Soap dish stainless steel, approximate size 160x 160x90mm fixed with chromium plated Brass screws, etc all complete as directed by the Engg in Charge.Note: Sample of soap dish with all accessories shall be got approved from EIC before fixing. |
| 73 | M & L for flush door shutters with partical board core 40 mm thick with decorative face veneers on both faces with lipping frame to match including provision of double leaf door where required, etc all complete as directed by the Engg in Charge.Note: sample of all material/s door & veneer to be approved from EIC before starting of work. |
| 74 | M & L for Glazed and skeleton shutters of 1st Class Hardwood, 30 mm thick, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, etc all complete as directed by the EIC.Note: sample of all related material/s of Hardwood and design etc of the shutter shall be got approved from the EIC before starting of work. |
| 75 | S & F of Sheet glass 4 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, etc all complete as directed by the EIC. |
| 76 | S & F of Brass barrel tower bolts (cromium plated) 200 mm , with cast or sheet barrel and rolled or cast bolts and fixed, etc all complete as directed.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 77 | S & F of Brass barrel tower bolts (cromium plated) 100 mm , with cast or sheet barrel and rolled or cast bolts and fixed, etc all complete as directed.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 78 | S & F of Brass sliding door bolt (cromium plated) 300 mm with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 79 | S & F of Butt hinges, cast brass, (cromium plated) with mild steel hinge pin, bright polished and fixed, Type B-12, 125 mm size, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 80 | S & F of Parliament hinges, cast brass, (cromium plated) bright polished and fixed of size 125 mm, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 81 | S & F extruded Brass handles (chromium plated), fabricated type, polished bright of size 125 mm, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 82 | S & F of gate & shutter Hook & eyes of Size 150 mm, Brass Wire Type, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 83 | S & F of Curtain rails of anodised aluminium alloy with fixing brackets, stops, rollers, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 84 | S & F of Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including fixing of beadings, etc all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 85 | S & F rolled sections as in framing for cladding, glazing and the like, including box type protection cage for windows, other openings etc. fixed with angle cleats and connecting plates, etc. all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 86 | S & F of Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete, etc. all complete as directed by the EIC.Note: sample of all related material/s shall be got approved from the EIC before use in work. |
| 87 | S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before use in work.Note: (i) Sample of all MS sections shall be got approved from EIC before fixing.(ii) The Contractor shall make his own design for trusses which shall be well within the estimated qty & shall be solely responsible for effective performance of structure. The design made by the Contractor for truss along with the required qty shall be shown to EIC before start of work. (iii) The MS portion to be embedded in concrete or to be attached with masonry shall be applied with two coats of black Japan paint. |
| 88 | S & F Galvanized, corrugated mild steel sheeting 0.63 mm thick (Make: JSW / Tata / SAIL) with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from EIC before fixing. |
| 89 | S&F thermal insulation hybrid XLPE air bubble sheet Nominal 15 mm thick laminated on both side with pure aluminum foil , bubble size 10mm x 4mm XLPE i.e. chemically crossed linked, closed cell, polythene foam insulation having thermal conductivity of the best quality i.e. 0.0329W/m.k at 23deg C . Suitable for wide temperature range from -40degC to +115 deg C , unaffected by most mild acids and alkali, offers high resistance to ingress of moisture , enhance overall acoustic property and reducing rainwater noise in metal roofing.etc all complete as directed by EIC Sample should be approved before execution.(Make:Arolam Ultra/ Star-Pack/ Tirisystem).Note: Sample of all materials shall be got approved from EIC before fixing. |
| 90 | S & F of Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of selected colour and pattern as approved, having tensile strength of 550 Mpa (Make: Tata Bluescope \\"Durashine\\" / JSW \\"Colouron+\\") as in roof covering/cladding to wall, fixed with self tapping screws as specified with ridge matching to the profile / pattern of sheet, end sheets of required pattern with curved portion at end on all sides as desired & approved for architectural requirement including all safety precautions, complete cleaning of premises, etc all complete as directed by the Engg in Charge.Important Notes: (i) Sample of all ancillary items for roof work shall be got approved from the Engg in Charge for all materials before fixing.(ii) Contractor shall submit original invoice (GST bill) of the material. (iii) The Self tapping screws shall be of length such that it shall penetrate properly into purlin ranging from Galvalume sheet, insulation panel, supporting MS flats etc. |
| 91 | S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick (Make: Tata Bluescope \\"Durashine\\" / JSW \\"Colouron+\\") of desired colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, etc all complete as directed by the Engg in Charge.Note: (i) Sample of roof sheet shall be got approved from the Engg in Charge for all materials before fixing. (ii) Contractor shall submit original invoice (GST bill) of the material. |
| 92 | M & L for preparation of wooden surfaces of any description, not otherwise described, over 10cm width or girth, priming with suitable primer and applying two coats of synthetic enamel (Make for Primer & Paint: 1st Quality paint from M/s Asian Paints / Birla Opus / Nerolac Paints / Berger Paints) etc all complete as directed by the Engg in Charge.Note: Sample of Paint shall be got approved from the EIC. The decision of the EIC with respect to Make of paint to be used in work shall be final and binding on the Contractor. |
| 93 | M & L for preparation of steel, iron , metal surfaces of any description, not otherwise described, over 10cm width or girth, priming with suitable primer and applying two coats of synthetic enamel (Make for Primer & Paint: 1st Quality paint from M/s Asian Paints / Birla Opus / Nerolac Paints / Berger Paints) etc all complete as directed by the Engg in Charge.Note: Sample of Paint shall be got approved from the EIC. The decision of the EIC with respect to Make of paint to be used in work shall be final and binding on the Contractor. |
| 94 | M & L for application of 3 mm thick wall care putty (Make: JK / Birla / Asian Paints) over the prepared wall surface prior to painting work etc all complete as directed by the EIC.Note: Sample of material shall be got approved from the EIC before starting of work. |
| 95 | M & L for application of approved quality Distemper Oil Emulsion on Walls in Two Coats including following procedure:(i) Preparation of surfaces including complete removal of existing treatment by wire brushing, scrapping, washing down etc.(ii) Apply one coat of primer (Make: 1st quality from Asian Paints / / Birla Opus / Nerolac Paints wall primer) as required for Distemper Oil Emulsion. Sand the surface with emery paper No.320 and wipe clean. (iii) Applying two coats of approved make & colour Distemper Oil Emulsion (Make 1st Quality from : Asian Paints / Birla Opus / Nerolac Paints ) as per manufacturer's specification. The application shall be done by using brush / roller. Stir the paint well before use. A gap of 4-6 hours should be given between each coat, the painted surface shall be got approved from competent Factory authority & rectifications, improvements if any shall be carried out by the Contractor at his own risk & cost etc, all complete as directed by Engg-in-Charge.Note: Sample of all materials shall be got approved from the EIC before starting of work. |
| 96 | M & L for application of approved quality Distemper Oil Emulsion on Ceiling in Two Coats including following procedure:(i) Preparation of surfaces including complete removal of existing treatment including complete removal of existing treatment by wire brushing, scrapping, washing down etc.(ii) Apply one coat of primer (Make: 1st quality from Asian Paints / / Birla Opus / Nerolac Paints wall primer) as required for Distemper Oil emulsion. Sand the surface with emery paper No.320 and wipe clean. (iii) Applying two coats of approved make & colour Distemper Oil Emulsion (Make 1st Quality from : Asian Paints / Birla Opus / Nerolac Paints ) as per manufacturer's specification. The application shall be done by using brush / roller. Stir the paint well before use. A gap of 4-6 hours should be given between each coat, the painted surface shall be got approved from competent Factory authority & rectifications, improvements if any shall be carried out by the Contractor at his own risk & cost etc, all complete as directed by Engg-in-Charge.Note: Sample of all materials shall be got approved from the EIC before starting of work. |
| 97 | M & L for application of 3 mm thick wall care putty (Make: JK / Birla / Asian Paints) over the prepared ceiling surface prior to painting work, etc all complete as directed by the EIC.Note: Sample of material shall be got approved from the EIC before starting of work. |
| 98 | M & L for Clean Sawn Second class hard-wood timber framed and fixed in scantlings at any height or position for repairs, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before starting of work. |
| 99 | M & L for Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads of 2nd class hardwood with cross section area exc 6 & n exc 13 Sq cm, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before starting of work. |
| 100 | S & F Asbestos cement plain building boards 6 mm thick, fixed to timber framework with screws, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before starting of work |
| 101 | M & L for preparation of old surfaces, priming with alkali resistant priming paint preparatory to distempering and distempering walls with distemper oil emulsion in two coats, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before starting of work |
| 102 | M & L for External wall painting in Two Coats including following procedure:(i) Complete removal of existing treatment, it shall be ensured that the surface to be painted must be free from any loose paint, dust or grease. Any previous growth of fungus, algae or moss should be removed thoroughly by vigorous wire brushing and cleaning with water. Surface imperfection such as holes, dents fine cracks should be filled with exterior wall putty (Make: Asian / Nerolac) or mixture of white cement and fine sand in proportion 1:3. [The surface such prepared shall be shown to SIC & EIC for inspection before application of Primer](ii) Applying one coat of Exterior Wall Primer (Make: Asian / Nerolac) by thinning 1liter of primer with 1 liter of water. Allow the primer coat to dry for 4 hours. [The surface after application of Primer shall be shown to SIC & EIC before application of 1st coat of Exterior Emulsion](iii) Applying two coats of Exterior Emulsion, (Make: Apex Weather Proof Exterior Paint from Asian Paints / Excel Total Acrylic Exterior Emulsion from Nerolac Paints) by diluting 1 lit paint with 400ml of water. A gap of 4-6 hours should be given between two coats. The work to be carried out up to 18m height including necessary scaffolding ,staging and all safety equipments, including complete cleaning of site etc. all complete as directed by Engg-in-Charge. [The surface after application of 1st Coat shall be shown to SIC & EIC for inspection before application of 2nd Coat of Exterior Emulsion. Subsequently the surface after application of 2nd Coat shall be shown to SIC & EIC for final inspection]Note: Sample of all materials shall be got approved from the EIC before starting of work. |
| 103 | M & L for preparation of old surfaces and applying two coats of cement paint on walls, etc all complete as directed by the EIC.Note: Sample of all materials shall be got approved from the EIC before starting of work. |
| 104 | Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 liters per linear meter including drilling and plugging holes etc. in apron, etc all complete as directed by the EIC.Note: (i) The Contractor shall submit the Original Tax invoice of the Anti Termite solution purchased for the work.(ii) The Contractor shall submit pics, recordings of the work being carried out to the EIC.(iii) Sample of all materials shall be got approved from the EIC before starting of work |
| 105 | M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, etc all complete as directed by the EIC.Note: (i) The Contractor shall submit the Original Tax invoice of the Anti Termite solution purchased for the work.(ii) The Contractor shall submit pics, recordings of the work being carried out to the EIC.(iii) Sample of all materials shall be got approved from the EIC before starting of work. |
| 106 | M & L for Site clearance including removal of all wild vegetation, leveling of area, cleaning and removal of all rubbish from the inside and surrounding of premises, sweeping clean and washing down with water all the rooms, etc all complete as directed by the EIC. |
| 107 | M & L for walling of random ruble masonry in Cement Moratr 1:6, etc all complete as directed by the EIC. |
| 108 | S&F precast cement concrete Type B1 1;2:4 (20mm graded aggregate) set in cement mortar 1:4 Pillar for Fencing Boundry Post / pillar /columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including Steel reinforcement, chamfers, weatherings, and dismantling old concrete post throating etc. and setting in mortar complete with joints to match etc all complete as directed by Engg-in-Charge. Note: (i) Sample of Pillar (aprox size 150x150mm and 2.4m ht ) with groove for placing fencing Planks should be approved before Fixing by Engg-in-Charge.(ii) Other normal concrete pillar of Approx. Cross Section of 0.10 m X 0.10 m and height 2.10 m, without groove but arrangement for fixing barbed wire shall also be got approved from the EIC for proposed fencing of Servant Qtr |
| 109 | S&F Providing precast cement concrete Type B0 1:2:4(12.5mm graded aggregate) set in cement mortar 1:4 fencing planks/ louvres and jallies, 50mm thick (measured solid), including dismantling old concrete fencing all steel reinforcement, mouldings, grooves for fixing with precast pillar/Poles/ post/ column, etc all complete as directed by Engg-in-Charge.Note: Sample of fencing planks / Louvers (aprox size 300x1800mm and 50mm thick) with groove for placing in fencing Post/ pillar/ column should be approved before Fixing by Engg-in-Charge. |
| 110 | S & F Rotational moulded polyethylene water storage tanks 1000 Litre capacity (cylindrical vertical with closed top) (Make: Sintex / Plasto / Supreme ) hoisted and fixed in position all as specified in SSR Part I including supply & fixing of float valve, all connections, secured in position, etc all complete as directed by the EIC.Note: Sample of water tank shall be got approved from the EIC before fixing. |
| 111 | S & F Rotational moulded polyethylene water storage tanks 500 Litre capacity (cylindrical vertical with closed top) (Make: Sintex / Plasto / Supreme ) hoisted and fixed in position all as specified in SSR Part I including supply & fixing of float valve, all connections, secured in position, etc all complete as directed by the EIC.Note: Sample of water tank shall be got approved from the EIC before fixing. |
| 112 | M & L for excavating in post holes in Hard Dense Soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, etc all complete as directed by the EIC. |
| 113 | S & F of Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed in wire entanglements aprons, barriers, gates, etc. (each line wire to be measured), etc all complete as directed by the EIC.Note: Sample of GI Barbed wire shall be got approved from the EIC before starting of work. |
| 114 | M & L for Mirror polishing on marble/ granite/ Kota stone/ stone work, where ever required like mosaic tiling work to give high gloss finish, etc all complete as directed by the EIC.Note: Contractor shall make the sample polish area of not less than 1 sq.m and shall get the same approved from the EIC before execution of the work. |
| 115 | Supply & Fixing Sheet Metal Enclosure Single Pole & Neutral 12 way for 230 VAC Supply, (Make:Siemens/L&T/Havels) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 116 | Supply & Fixing of Isolator TPN MCB 63 Amps (Make: Siemens/L&T/Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 117 | Supply & Fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning. (Make:Siemens/L&T/Legrand)etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 118 | Supply & Fixing of Piano (Modular) Type switches 1 way, 5A (Make:Anchor/ Roma/GM/Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 119 | Wiring for Circuit / Submain wiring along with earth wire with 2x4 sq. mm 1x4 sq. mm earth wire of FR PVC insulated copper conductor (Make:Finolex / Polycab / Havells ) in PVC Casing & Caping Make: Precision / Pressfit, etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 120 | Wiring for Circuit / Submain wiring along with earth wire with 2 x 2.5 sq.mm + 1 x 2.5 Sq.mm earth wire of FR PVC insulated copper conductor (Make:Finolex / Polycab / Havells ) in PVC Casing N Caping Make: Precision / Pressfit, etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 121 | Wiring for Circuit / Submain wiring along with earth wire with 2 x 1.5 sq.mm + 1 x 1.5 Sq.mm earth wire of FR PVC insulated copper conductor (Make:Finolex / Polycab / Havells ) in PVC Conduit Make: Precision / Pressfit, etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 122 | Wiring for Circuit / Submain wiring along with earth wire with 2 x 1.5 sq.mm + 1 x 1.5 Sq.mm earth wire of FR PVC insulated copper conductor (Make:Finolex / Polycab / Havells ) in PVC Casing n Caping Make: Precision / Pressfit, etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 123 | One Light Point or one Fan point controlled by one switch with cables 1.5 Sq.mm copper multistrand wire, (Make: Polycab/ Finnolex/KEI/RR) Size in PVC Casing n Caping of thickness 2 mm, (Make:Pressfit/Prestige) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 124 | Supply and Fixing of MODULAR METAL/PVC FLUSH BOX 6 Module, (Make: Havells/ Pressfit/ Legrand/GM) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 125 | Supply and Fixing of MODULAR WHITE COVER PLATE WITH FRAME 6 Module (Make: Havells/ Pressfit/ Legrand/GM) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 126 | Supply and fixing LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete, etc all complete as directed by the EIC. |
| 127 | S & F of Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings/Casing Caping Wiring Angle or straight (Make:Anchor/Roma/GM/Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 128 | S & F of Switch socket Combination 6A, 3 pin, 3 module Flash type (Make:Anchor/Roma/GM/ Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 129 | S & F of Switch socket Combination 16A, 6 pin, 3 module (Make:Anchor/Roma/GM/ Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 130 | S & F of Bell push, flush type, 5 amp with suitable Box (Make:Anchor/Roma/GM/Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 131 | Fixing only Ding-Dong Bell along with suitable fixing arrangement (M.D supply) etc all complete as directed by the EIC. |
| 132 | S & F of Ceiling Rose 6A, 3 Point (Make:Anchor/Roma/GM/Legrand) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 133 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) (Make:Crompton/Bajaj/Automberg) etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. |
| 134 | Supply & Fixing 35 Watts LED street light fittings, etc all complete as directed by the EIC.Note: Sample shall be got approved from the EIC before fixing. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysSep 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender