Tender For Development Work Of Remaining Roads, Drains, Sewerlines, Waterline And Parks In Pocket C Madhuban Bapudham Scheme (Part-A)
Tender Value
23 Crore
Estimated cost
Bid Submission
05 Oct 2026
19 days left
EMD
46.02 Lakhs
Bank guarantee accepted
Document Fee
18054
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ghaziabad → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development Work Of Remaining Roads, Drains, Sewerlines, Waterline And Parks In Pocket C Madhuban Bapudham Scheme (Part-A)
BOQ
| Sl. No. | Item Description |
| 1 | Carriage of earth by mechanical transport including loading, unloading and stacking, lead up to 3 km (complete as per direction of Engineer-in-Charge) DSR-2023/1.1 |
| 2 | Earth work by mechinical / manual means in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with 'A tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and for all lift. All kinds of soil DSR-2023/2.2.1 DSR-2023/2.2 |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed All kinds of soil .DSR-2023/2.6.1 .DSR-2023/2.6 |
| 4 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc, not exceeding 80 mm dia. DSR-2023/2.10.1.1 |
| 5 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR-2023/2.10.1.2 |
| 6 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm. DSR-2023/2.10.1.3 |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. DSR-2023/2.25 |
| 8 | Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. DSR-2023/2.26 All kinds of soil. DSR-2023/2.26.1 |
| 9 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. DSR-2023/2.31 |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : DSR-2023/4.1 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR-2023/4.1.2 |
| 11 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR-2023/4.1.3 |
| 12 | 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). DSR-2023/4.1.8 |
| 13 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:DSR-2023/4.2 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)DSR-2023/4.2.3 |
| 14 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) DSR-2023/4.10 |
| 15 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.DSR-2023/4.13 |
| 16 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :DSR-2023/5.1 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) DSR-2023/5.1.2 |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for :DSR-2023/5.9 Foundations, footings, bases of columns, etc. for massconcrete DSR-2023/5.9.1 |
| 18 | Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc. DSR-2023/5.9.2 |
| 19 | Suspended floors, roofs, landings, balconies and accessplatform DSR-2023/5.9.3 |
| 20 | Columns, Pillars, Piers, Abutments, Posts and Struts DSR-2023/5.9.6 |
| 21 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars. Fe-500 D DSR-2023/5.22.6 Qty @ 1.50% of concrete qty DSR-2023/5.22 |
| 22 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:DSR- Cement mortar 1:6 (1 cement : 6 coarse sand)DSR-2023/6.1.2 |
| 23 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) DSR-2023/6.4.2 |
| 24 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.DSR-2023/10.25.2 DSR-2023/10.25 |
| 25 | 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand)DSR-2023/13.4.2 |
| 26 | 15 mm cement plaster on rough side of single or half brick wall of mix:DSR-2023/13.5 1:6 (1 cement: 6 coarse sand)DSR-2023/13.5.2 |
| 27 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.DSR-2023/13.80 |
| 28 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90litre/10 sqm) DSR-2023/13.46.1 |
| 29 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work DSR-2023/13.52.2 |
| 30 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work.DSR-2023/13.61.1 |
| 31 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re- olling the sub grade and disposal of surplus earthwith lead upto 50 metres.DSR-2023/16.1 |
| 32 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).DSR-2023/16.2 |
| 33 | Constuction of granular sub-base by providing close graded meterial (Grade-1) spreading in uniform layers with motor grader on prepared surface mixing by mix place method with rotavater at Omc and compacting with vibratory to achive the desired density complete as per MORTH clause 401 (without motor grader)-(AR) |
| 34 | Providing and laying spreading and compactive grade stone aggregate to WMM specification Incluid premixing the material with at OMC in mechanical mix plant close grade mixing in mechanical mix plant at OMC carriage of mixed material by tipper to site laying in uniform layers with paver in sub base /base course on well prepared surface and compacting with vibrating roller to achive the desired density 406 of MORT &H specification and as per direction of the engineer-in charge (A.R) |
| 35 | Providing and applying tack coat with 80/100 (VG10) bitumen on prepared surface of granular base including cleaning the road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means including supply of all materials labour T&P etc required for proper comletion of the work as per clause 503 of MORT&H specifications and as per direction of the Engineer-in-charge (A.R.) |
| 36 | Providing and applying tack coat with 80/100 (VG10) 0.30 kg per sqm on the prepared bitumeneous / granular surface cleaned with mechanical broom including supply of all materials labour T&P etc required for proper completion of the work as per clause 503 of MORT&H specification and as per dierction of the Engineer in charge (A.R.) |
| 37 | Providing and laying 50mm thk compacted bitumenous mecadam on prepared surface with 100-120 tonnes per hour batch type Hot mix plant producing an average output of 75 MT per hour using crushed agregated of specified grading-II(19mmNominal Size) premixed with 80/100 (VG10) bitumenous binder @ 3.30% by weight of total mix transporting the hot mix material to work site laying with a hydrostatic paver finisher with sensor control to the required grade level and alignment rolling with smooth wheeled grade level and alignment rolling with smooth wheeled vibratory (8-10 tonnes) roller for initial brake down rolling finish rolling by smooth wheeled tondom roller (8-10 tonnes) to achieve the desired compaction including supply of all materials labour T&P etc required for proper completion of the work as per clause 504 of MORT & H specification sand as per direction of the Engineer in charge (A.R.) |
| 38 | Providing and laying compacted semi dense bitumenous concrete with 100-120 tonnes per hour batch type Hot mix plant producing an average output of 75 MT per hour using crushed agregated of specifled grading-I premixed with 60 70 (VG30) bitumenous binder @ 4.50% by weight of total mix and filler @ 2% by weight of total mix transporting the hot mix material to work site laying with a hydrostatic paver finisher with sensor control to the required grade level and alignment rolling with smooth wheeled vibratory (8-10 tonnes) roller for initial brake down rolling finish rolling by smooth wheeled tondom roller (8-10 tonnes) to achieve the desired compaction including supply of all materials labour T&P etc required for proper completion of the work as per clause 508 Grade-l(13 mm nominal size) of MORT & H specification sand as per direction of the Engineer in charge. (AR) |
| 39 | Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/- 5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.DSR-2023/16.50 |
| 40 | Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.DSR-2023/16.62 |
| 41 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge.DSR-2023/16.63 |
| 42 | Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-charge.DSR-2023/16.65 |
| 43 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).DSR-2023/16.69 |
| 44 | Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge.80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.DSR-2023/16.91.2 |
| 45 | Providing and fixing Polyethylene- Aluminium- Polyethylene (PE-AL- PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required ) e.g. elbows, tees, reducers, couplers & connectors etc. with trenching, refilling and testing of joints complete as per direction of the engineer in charge : External work 2025 (25 mm OD ) pipe.DSR-2023/18.3.3 |
| 46 | 2532 (32 mm OD ) pipe.DSR-2023/18.3.4 |
| 47 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore DSR-2023/18.17.1 |
| 48 | 50 mm nominal bore DSR-2023/18.17.4 |
| 49 | Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :15 mm nominal bore DSR-2023/18.20.1 |
| 50 | 20 mm nominal bore DSR-2023/18.20.2 |
| 51 | 25 mm nominal bore DSR-2023/18.20.3 |
| 52 | Providing and laying D.I. Specials of Class K - 12 suitable for mechanical jointing as per IS : 9523 : Up to 600 mm dia DSR-2023/18.25.1 &18.25.2 |
| 53 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameter DSR-2023/18.31.1.2 |
| 54 | 150 mm diameter DSR-2023/18.31.3.2 |
| 55 | 200 mm diameter DSR-2023/18.31.4.2 |
| 56 | 250 mm diameter DSR-2023/18.31.5.2 |
| 57 | Constructing masonry Chamber45x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : irrigation hydrant valve Based on With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Based on DSR 2023 18.32 |
| 58 | Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.l. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 DSR-2023/18.35.1 DSR-2023/18.35 For Butter Fly valve |
| 59 | For Washout Valves |
| 60 | For Water Meters |
| 61 | Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. 20 mm diameter pipe DSR-2023/18.41.2 |
| 62 | 25 mm diameter pipe DSR-2023/18.41.3 |
| 63 | 100 mm diameter pipe DSR-2023/18.41.9 |
| 64 | 150 mm diameter pipe DSR-2023/18.41.10 |
| 65 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :50 mm dia DSR-2023/18.59.1 |
| 66 | 80 mm dia DSR-2023/18.59.2 |
| 67 | Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :100 mm dia nominal bore DSR-2023/18.60.2 |
| 68 | 150 mm dia nominal bore DSR-2023/18.60.3 |
| 69 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-7 pipes DSR-2023/18.72.1 |
| 70 | 150 mm dia Ductile Iron Class K-7 pipes DSR-2023/18.72.2 |
| 71 | 200 mm dia Ductile Iron Class K-7 pipes DSR-2023/18.72.3 |
| 72 | 250 mm dia Ductile Iron Class K-7 pipes DSR-2023/18.72.4 |
| 73 | 400 mm dia Ductile Iron Class K-7 pipes DSR-2023/18.72.7 |
| 74 | Disinfecting C.I. water mains by flushing with water containing bleaching powder @ 0.5 gms per litre of water and cleaning the same with fresh water, operation to be repeated three times including getting the sample of water from the disinfected main tested in the municipal laboratory. 100 mm diameter C.I. pipe DSR-2023/18.80.2 |
| 75 | 150 mm diameter C.I. pipe DSR-2023/18.80.4 |
| 76 | 200 mm diameter C.I. pipe DSR-2023/18.80.5 |
| 77 | 250 mm diameter C.I. pipe DSR-2023/18.80.6 |
| 78 | 400 mm diameter C.I. pipe DSR-2023/18.80.9 |
| 79 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 150 mm dia. R.C.C. pipe DSR-2023/19.2.2 |
| 80 | 250 mm dia. R.C.C. pipe DSR-2023/19.2.4 |
| 81 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 250 mm dia. R.C.C. pipe DSR-2023/19.3.4 |
| 82 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe DSR-2023/19.6.2 |
| 83 | 250 mm dia. R.C.C. pipeDSR-2023/19.6.3 |
| 84 | 300 mm dia. R.C.C. pipe DSR-2023/19.6.4 |
| 85 | 450 mm dia. R.C.C. pipe DSR-2023/19.6.5 |
| 86 | Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with S.F .R.C. cover and frame (heavy duty , HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR-2023/19.9.1.1 |
| 87 | Extra depth for circular type manhole 0.91 m internal dia (at bottom) beyond 0.91 m to 1.67 m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR-2023/19.10.1 |
| 88 | Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR-2023/19.11.1.1 |
| 89 | Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR-2023/19.12.1 |
| 90 | Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : 19.13.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-19.13.1.1) |
| 91 | Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : DSR-2023/19.14.1 |
| 92 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 1 12 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.DSR-2023/19.16 |
| 93 | Extra for Providing and fixing medium duty SFRC cover with cement concrte as per standard detail: H D - 20 Circular shape 560 mm internal diameter DSR-2023/19.19.3.1 |
| 94 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR-2023/19.27.1 |
| 95 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :DSR-2023/19.30.2 |
| 96 | Applying stamping finish to the top surface of freshly laid plain/reinforcedcement concrete of specified grade in porticos, sidewalks, driveways, pool decks and open yards as per direction of the Engineer-in-Charge. The process shall include the following:- • The concrete shall be placed and screeded to the finished grade, and floated to a uniform surface by using standard finishing techniques. The approved color hardener @ 2.7 kg/sqm shall be applied evenly to the surface of the fresh concrete by the dry shake method by sprinkling in two or more shakes, floated after each shake and trowelled only after the final floating. The approved release agent @ 0.113 kg/sqm shall be applied evenly to the trowelled surface before stamping or the said release agent can be applied to the flexible polyurethane stamp moulds of approved design and in required sizes to achieve final stamped pattern. These stampings shall be placed on the surface of concrete in three to four pieces at a time and tapped gently with rammers of sufficient size & weight to leave proper stamp marks and the process repeated for the remaining concrete surface till the whole surface to be stamped is completed within the time while concrete is in plastic stage of setting. • After stamping, the curing shall be done as per manufactures specifications. After initial curing the imprinted joints shall be grouted using cement slurry mixed with color hardener as per the requirement. The surface shall be sealed by applying acrylic based sealer not less than 0.167 litre/sqm.on finished surface. • The construction joints shall be provided by groove cutting of size 4 mm x 20 mm in panel size 3m x 3 m or lesser as per the site conditions and filling the same with 10 mm baker rod and providing and laying (PU) Polyurethane based joint sealer of approved make as per manufacturer’s specifications and finished by applying Polyurethane resin based top protective clear coat of minimum 80 micron applied with rollers on properly cured and dry clean surface. (Cost of concrete for flooring is not included in this item which shall be paid separately.) (DSR-26.83) |
| 97 | Horticulture :- Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) -Holes 45 cm dia, and 45 cm deep (For Post of MS Grill= 2xLOR/1.5+1) HOR DSR 2025 2.14.4 |
| 98 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment) -HOR DSR 2025 2.2 |
| 99 | Supplying and stacking of sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment) (Considered 20% of good earth)-HOR DSR 2025 2.3 |
| 100 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) (Considered 20% of good earth-Screened through sieve of I.S. designation 4.75 mm HOR DSR 2025 2.4.3 |
| 101 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge HOR DSR 2025 2.9 |
| 102 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). HOR DSR 2025 2.8 |
| 103 | Supply of following sizes pipes for distribution system conforming to latest/ relevant I.S. 4984/1995 Specifications with all jointing materials and specials conforming to latest/relevant I.S. specifications including F.O.R. destination and all taxes and insurance etc. with loading, unloading and Carting up to site of work, also including specials for these pipes and lowering them into the trenches and laying true to alignment and gradient and jointing etc. complete (including testing of pipe lines and cutting of pipes for making up the length but excluding the cost of trenches) all complete as per instructions of Engineer ‐in ‐ charge. 160 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 104 | 110 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 105 | 63 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 106 | 52 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 107 | 40 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 108 | 25 mm dia HDPE Pipe PN‐6: Class PE‐100 |
| 109 | Providing & Fixing of Butterfly Valves with off set design DISC in SS316 having dual shaft with SS410 material for normal Valves as well as extended shaft for underground installation as per IS :13095 Make AIP/ ADVANCE / AUDCO 150 mm diameter |
| 110 | 100 mm diameter |
| 111 | 65 mm diameter |
| 112 | 400 mm diameter |
| 113 | C.I. Washout/Scour Valve 100 mm dia valve |
| 114 | C.I. Non Return Valve downstream of scour valve conforming to IS:5312 100 mm dia valve |
| 115 | 150 mm dia valve Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender