Tender For Construction Of Higher Secondary School Under Samgra Shiksha (+2 Science Stream At Chiliguda High School Under Junagarh Block In The District Of Kalahandi For The Year 2026-27 (Building)
Tender Value
2.32 Crore
Estimated cost
Bid Submission
29 Sep 2026
16 days left
EMD
2.32 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kalahandi → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Higher Secondary School Under Samgra Shiksha (+2 Science Stream At Chiliguda High School Under Junagarh Block In The District Of Kalahandi For The Year 2026-27 (Building)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches in hard soil including dressing and leveling the bed upto the required depth and depositing the excavated materials with all leads and lifts T&P shoring & Shuttering if required etc. complete as directed by the Engineer-in-charge. |
| 2 | Supplying filling in foundation and plinth with sand including watering ramming, cost, conveyance, royalties and all taxes of materials and cost of labour with T&P required for the work etc. complete (measurement will be taken on finished section only etc.complete as directed by the Engineer-in-charge. |
| 3 | Cement concrete (1:3:6 ) in foundation and plinth below the base course of terrazzo flooring using 4cm (1 1/2\\") size black hard hand broken granite stone metals of approved quality from approved quarry including lowering laying concrete watering and curing etc. complete to required levels laid in layers not exceeding 0'-6\\" thick inlcuding cost, conveyance, royalties and all taxes of all materials and cost of all labour with T & P required for the work complete. |
| 4 | Brick masonary in cement mortar (1:6) using K.B.Bricks / Cement flyash of size 10\\" x 5\\" x 3\\" having crushing strength not lessthan 75 Kg/Cm2 after immersing the bricks for six hours in water before use in Foundation and plinth in all florrs with all necessary projection, cutting mlulding, corbelling, champering, watering and curing including cost conveyance, royalties and taxes of all materials and labour T&P required for the work etc.complete as per the direction of Engineer in Charge. Ground Floor |
| 5 | R.C.C.work of M-25 having a minimum comprresive strength (in work test) 250 kg/Cm2 in 15 cm cubes at 28 days after mixing and test conducted in accordance with IS 456 and IS 516 using 12mm size black hard crusher broken granite chips including hoisting,lowering laying and compacting concrete by using vibrator with watering and curing for 28 days centering and shuttering and finishing the exposed surface smooth providing grooves or beds whereever necessay including cost conveyance,royalties and all taxes of all materials and cost of all labour with T&P required for the work etc.complete in all respect but excluding cost of M.S.Rods or Tor Steel and binding wires and labour charge for bending binding and tying the grills etc.complete in all respect as per direction of Engineer-in-charge.Column Base & Footing |
| 6 | Plinth Bend/Grade BeamGround Floor |
| 7 | Bed BlockGround Floor |
| 8 | First Floor |
| 9 | Lintel BandGround Floor |
| 10 | First Floor |
| 11 | Second Floor |
| 12 | Column in Super structureGround Floor |
| 13 | First Floor |
| 14 | Second Floor |
| 15 | Wall Beam & TBeamsGround Floor |
| 16 | First Floor |
| 17 | Second Floor |
| 18 | Stair CaseGround Floor |
| 19 | First Floor |
| 20 | Second Floor |
| 21 | Chajja & FinGround Floor |
| 22 | First Floor |
| 23 | Second Floor |
| 24 | Roof SlabGround Floor |
| 25 | First Floor |
| 26 | Second Floor |
| 27 | Providing HYSD bar reinforcement for R.C.C. work including Straightening, cutting, bending, binding, welding, tying the grills, laying and placing in proper position as per approved design and drawing including cost, conveyance of 18 to 20 gauge binding wire cost and conveyance of HYSD bars complete in all respect as per specification for road & Bridge and direction of Eng in Charge.Ground Floor |
| 28 | First Floor |
| 29 | Second Floor |
| 30 | Brick masonary in cement mortar (1:6) using K.B.Bricks/Cement flyash of size 10\\" x 5\\" x 3\\" having crushing strength not lessthan 75 Kg/Cm2 after immersing the bricks for six hours in water before use in superstructure in all florrs with all necessary projection, cutting mlulding, corbelling, champering, watering and curing including cost conveyance, royalties and taxes of all materials and labour T&P required for the work etc.complete as per the direction of Engineer in Charge. Ground Floor |
| 31 | First Floor |
| 32 | Second Floor |
| 33 | 20mm thick grading cement plaster ( 1:4 ) finished smooth over R.C.C.slab including watering curing cost conveyance royalty and labour required for the work etc.complete as per direction of Engineer-in-charge.Ground Floor |
| 34 | First Floor |
| 35 | Second Floor |
| 36 | 12mm thick cement plaster (1:4) over brick work including cement punning and Bitumen painting on top of wall etc. complete.Ground Floor |
| 37 | First Floor |
| 38 | Second Floor |
| 39 | 20mm thick cement plaster (1:6)in finished smooth to inside smooth surface of brick walls afrer racking out joints including watering and curing etc.complete with cost,conveyance royalties,all taxes and cost of all materials and cost of all labour with T&P requred for the work complete. as per the direction of Engineer in Charge.Ground Floor |
| 40 | 12mm(1/2\\") thick cement plaster (1:6) in finished smooth to outside smooth surface of brick walls afrer racking out joints including watering and curing etc.complete with cost,conveyance royalties,all taxes and cost of all materials and cost of all labour with T&P requred for the work complete. as per the direction of Engineer in Charge.Ground Floor |
| 41 | First Floor |
| 42 | Second Floor |
| 43 | 16mm(5/8\\") thick cement plaster (1:6)in finished smooth to inside smooth surface of brick walls afrer racking out joints including watering and curing etc.complete with cost,conveyance royalties,all taxes and cost of all materials and cost of all labour with T&P requred for the work complete. as per the direction of Engineer in Charge.Ground Floor |
| 44 | First Floor |
| 45 | Second Floor |
| 46 | Supplying , fitting and fixing of 32mm thick flush door shutter with approved quality of 30mm thick BWR block board pasted with 1mm thick Sunmica on both side of approved design and quality including cost of all door with frame fitting and fixture etc complete(SR 2022 misla. item no-9/page-234)Ground Floor |
| 47 | First Floor |
| 48 | Supplying , fitting and fixing of two track UPVC sliding window of approved make with 6 mm thick glass of approved quality complte with frame,shutters and all fiiting and fixtures (SR-2022 Mis. item n0-13/page no-235)Ground Floor |
| 49 | First Floor |
| 50 | Supplying,fitting and fixing of M.S. doors, windows and iron grill gate made out of (45x45x60)mm size angular frame with square bar M.S. flat for grills of approved design icluding all cost conveyance taxes etc. complete. ( Prevaling lowest local market rate and excluding labour for fixing )Ground Floor |
| 51 | First Floor |
| 52 | Second Floor |
| 53 | Labour for fitting and fixing of MS Shutters for doors, window and grill gates, Collapsible gate including filling the holes with C.C (1:3:6) etc.complete as per the direction of Engineer in Charge.Ground Floor |
| 54 | First Floor |
| 55 | First Floor |
| 56 | Fixing of vetrified tiles in floors,treads and landings on 25mm thick bed of cement mortar (1:1) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile. complete in all respect as per the direction of Engineer in Charge.Ground Floor |
| 57 | First Floor |
| 58 | Fixing of Vetrified tiles in dados,skirting and in rises of steps on 12mm thick bed of cement plaster (1:3) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile. complete in all respect as per the direction of Engineer in Charge.Ground Floor |
| 59 | First Floor |
| 60 | Fixing chequred tiles in floors,treads and landings on 25mm thick bed of cement mortar (1:1) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile. complete in all respect as per the direction of Engineer in Charge.Ground Floor |
| 61 | Supplying, fitting afixing of stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc. with cost conveyance, taxes of all materials labour, T&P etc. required for the complete in all respect. etc. complete etc.complete as per direction of Engineer-in-charge.Ground Floor |
| 62 | First Floor |
| 63 | Second Floor |
| 64 | Finishing wall surface with two coats of approved quality of weather seal coat of approved shade over a coat of primer including cost of all materials etc. complete. as per direction of Engineer In Charge.Ground Floor |
| 65 | First Floor |
| 66 | Second Floor |
| 67 | Finishing wall surface with acrylic wall putty finished smooth to exposed new plastered surface including cost of all materials etc.complete. as per direction of Engineer In Charge.Ground Floor |
| 68 | First Floor |
| 69 | Second Floor |
| 70 | Painting two coats with any approved paint including cost of paintsGround Floor |
| 71 | First Floor |
| 72 | Second Floor |
| 73 | Cement washing one coat including watering ,curing with cost,conveyance, royalities of cement etc.Complete as per direction of Engineer-in-Charge.Ground Floor |
| 74 | First Floor |
| 75 | Second Floor |
| 76 | Distempering two coat over the including cost of distemper cost conveyance and all taxes of all materials and labor with T&P required for the work etc.complete in all respect etc. complete as per direction of Engineer in charge.Ground Floor |
| 77 | First Floor |
| 78 | Second Floor |
| 79 | Cement concrete of proportion (1:2:4) with 12mm (1/2\\") size hard granite crusher broken chips including watering curing, cost, conveyance, royalties and all taxes of all materials labour with T&P required for the work etc.complete as per direction of Engineer-in-charge.Ground Floor |
| 80 | Construction of Shoulder with approaved materials like Moorum obtained from locality with all lift and leads transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300.2 with all lead and lifts as per |
| 81 | Providing PVC Pipe 100 mm dian for rain water drainage from top up siab to ground including all labour and with clamps & fitting as per direction of the Engineer in charge |
| 82 | Recessed wiring to light point with 1.5 sq.mm FR PVC insulatedsingle core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5Amp, 250 V piano type modular switch ISI marked and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size , MS box with 1 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex/ L&T / Anchor / Havels /HPL/ V Guard )Group A |
| 83 | Group B |
| 84 | Group C |
| 85 | Recessed wiring to Fan Point inGroup C |
| 86 | Recessed wiring to Call Bell Point in... Group C |
| 87 | Recessed wiring to Exhaust Fan Point in Group B |
| 88 | S/F of Angle holder replacing Ceilling Rose |
| 89 | S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board |
| 90 | S/F of extension board of 6 modular Metal box with modular base & cover in recess including providing and fixing of 2 nos of 3pin 5/6amp modular socket out let & 2 nos of 5/6 amp piano type modular switch, connection, painting etc as required. |
| 91 | S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 6 pin 15/16 amp. piano type Modular switch & Socket, connection, painting etc as required |
| 92 | S/F of Power point with 4 modular & 2 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piano type Modular switch & Socket & Mini DP MCB, connection, painting etc as required for AC |
| 93 | S/F of 1 no of 5 pin 15/16 amp. Socket , 1 no of switch & 1 no of 15/16A top with modular mini MCB, in 6 modular box with cover with connection, painting etc as required for Inverter connection |
| 94 | S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. 4 Modular box with base & cover |
| 95 | 8 Modular box with base & cover |
| 96 | 12 Modular box with base & cover |
| 97 | Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make of wire - Finolex/L&T/Anchor/Havels/V-guard) 2x1.5+1x1.5 (1.8.1) |
| 98 | 2x2.5+1x1.5 (1.8.2) |
| 99 | 2x4+1x1.5 (1.8.3) |
| 100 | 2x6+1x2.5 (1.8.4) |
| 101 | Inverter wiring (1x1.5smm) Copper wire (1.19.1) |
| 102 | S/F of 'B/C/D' series SP MCB of 5 - 32A amp rating (As per direction of engineer in charge) 240Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP) (2.6.1) |
| 103 | Supply and fixing of 63A four pole (triple pole and neutral) 410 V residual current break (RCCB) having a sensitivity current up to 300 milli ampere in the existing MCB DB ISI marked complete with connection testing and commissioning etc as required. |
| 104 | Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make-Seimens/HPL/Anchor/L&T /Havels/C&S/R. K.) S/F of MCB 12 way Double door (1.3.7) |
| 105 | Earthing with G.I. Earth pipe 3 mtr Long 40mm dia ISI marked including accessories & providing masonary enclosure with cover plate having locking arrangement & watering pipe with charcoal & salt as required (3.2) |
| 106 | Supply & laying 6 SWG G.I. wire in recess for loop earthing as required (3.17) |
| 107 | Supply, Installation, Testing & Commissioning of exhaust fan upto 300 mm sweep in the exising opening, including making the hole to suit the size of the above fan making good the damaged complete, connection, etc as required. (1.43) |
| 108 | S/F of Call bell/Buzzer(Ding dong type) ISI marked suitable for DC/AC single phase 230 volts complete as required. (1.30) |
| 109 | S/F of computer board consisting of 3 nos of 5amp modular plug and modular switch & 1 no of Mini MCB complete with wiring on 12 modular M.S. box with modular cover. |
| 110 | S/F of 18-25Watt L.E.D Tube light fitting with all accessories and connections (Make:HPL-Neptune Havells-Elite LED Pride Plus/PAC/Crompton-RetroPLL |
| 111 | Supply of 1200mm A.C. Ceiling fan with all accessories and connections with out fan regulator (Make:Usha-Striker Millenium/Crompton-Jura /Anchor-XL/Havels-Velocity/Spark/Orient-Summer pride ) |
| 112 | S/F step type fan regulator |
| 113 | S/F of 15mm dia down rod with all accessories (1.35+1.40) |
| 114 | Supply & Fixing of 60 Watt single L.E.D street light fitting with LED & Electrinic driver including all accessories and connections (Make:Crompton/Phillips/HPL/Polycab/Havells) |
| 115 | S/F of fan hook 'S' type made of 16 mm MS rod for fixing in the Existing RCC Roof. |
| 116 | S/F of 12w Watt LED Bulb |
| 117 | S/F of 1.5T ,5Star,Inverter model, Split A.C Machine including out door stand (Make- Hitachi(V518PCBISH1)/Blue star(V518PCBISH1C)/Carrier(CAI19CE5R35F0)/Daikin/LG/Mitsubishi/O-General) Including Stabilizer and all Accessories |
| 118 | S/F of 2000VA/24V Invertor machine,Make-Heavy duty V-Turbo UPS-23509 (microtek)/PRIME 2250(V-GUARD)/EVO S 2300(LUMINOUS) and 180Ah tall tubular BatteryMake-Luminous /microtek/v-guard and 16A Delux plug Top with Luminous single Trolley for Inveryor Battery,2nos |
| 119 | Supply & fixing of 100 A TPN Panel board 1. 100A MCCB (Make- Legrand/Seimens/L&T/C&S/) & 100A kitkat & bus bar2. 32 A TPN MCB (Make- Legrand/Seimens/L&T/C&S/)- 2nos 3. 32A DP MCB (Make- Legrand/Seimens/L&T/C&S/)- 5 nos 4. 100 A 4P Manual changeover (Make- Legrand/Seimens/L&T/C&S/)- 1nos5. Digital Volt meter & Ameter three phase 6. All accesories & Connection (Rating & Danger borad) |
| 120 | Supply & Installation of 30 W Semi Integrated type Solar street lights having 80 Wp or more highly efficient Monocrystalline PV module & 12.8 V 30 Ah or more ) Lithium Ferrophosphate (LiFePo4) Battery having BIS ) which shall be inside the die cast alluminium housing luminaire housing (Theft retardant type), MPPT charge controller having > 92% efficiency & PIR Sensor. The initial lumen output of AIO street light shall be >4800 lumen or more in CCT 6000K (+/-500K) , Lumen efficacy > 160 lm/w as per LM 79 report of NABL Lab. The LED chip will be of OSRAM/NISCHIA/CREE/SEOUL Semiconductor only and should be with lenses for effective lighting distribution. The complete system & BMS should be designed to provide 2 days (24Hrs) back up in dimming mode by activating PIR sensor and battery should be kept inside the luminaire and Mono Crystalline Panel (Made in India ) , Multi purpose SA bracket to mounted on the ARM in south direction. The luminaire must be having I die cast alluminium housing street light with IP 66 protection for critical component like (LED compartment, Driver compartment & Battery) & IK 08 . The solar street lighting company has to supply Solar Panel , Solar light , battery , PIR sensor , Multipurpose SA bracket & other accessories with provision to fix the solar panel towards south direction for faster charging of battery. The Solar street light and the multipurpose Arm shall be fixed in Pole. The solar street lighting company has to offer Warranty on complete lighting system for a period of 5 years. The solar lighting company must submit the warranty certificate in the department by mentioning 5 years warranty on complete lighting system I.e, Light, Charge controller, Battery, Solar Panel, Module Mounting structure, Multipurpose Single Arm bracket etc against manufacturing defects .The Necessary after sales service to against manufacturing defects to be provided Solar lighting company through their Toll free base service service set up within 100 to 150 KM from the project site. 1. LM 79 REPORT NABL lab ) , 2. IK 08 (Report of NABL lab ), 3. IP 66 Report of NABL lab (Make-Panasonic Havels/Crompton/Philips/Wipro/) |
| 121 | Supply of 7 mtr long hot dip galvanized Octagonal pole having base dia of 175 mm and top dia of 70 mm and plate thickness of 4 mm or more complete with base plate and 4 nos. Jtype En 8 grade foundation bolts M24X750mm to withstand 180 KM / HR wind speed considering the weight. Solar lights fixed on the top of the pole . AIO Integrated Solar lights . One no of AIO Solar lights at a height of 7 mtr above ground .Both the Octagonal pole, En8 grade fdn bolts and bracket must be manufactured in the Octagonal pole manufacturing company. ( Bracket & En8 grade Fdn bolts manufactured by third party pole supplier/manufacturer shall not be acceptable). Make:- Utkarsh/RR Ispat/Vakrangee . |
| 122 | Labour for drilling a perfectly vertical bore hole at specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rigs or combination rigs as required to suit the site condition as per the direction of the Engineer-in-charge including use of own rigs with its accessories, tools and plants and consumables etc for lowering of 125 mm dia P.V.C/G.I/MS pipes for housing fitted socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/P.V.C/M.S casing pipes if required to prevent collapse of over burden is to be provided by the contractor including lowering and withdrawing after completion of the tubewell) Drilling of 200 mm dia bore :-00 mtr to 40.00 mtr For Rain Water Harvesting 5 nos 10mtr Each.( 50+5x10) |
| 123 | Drilling of 150 mm dia bore :- 41 mtr to 100 Mtr |
| 124 | Lowering of the following size G.I/P.V.C pipes with or without slotted pipes as per the necessary from ground level upto 30 mtrs depth and fitted and fixed up in perfectly vertical position including cutting and threading pipes and slotted pipe and supplying and fixing all jointing materials, tools and plants complete and keeping the top of the casing pipe threaded including plugging tubewell to prevent entry of foreign materials from above. Lowering of 125 mm dia PVC pipes :- 00mtr to 30.00 mtr |
| 125 | Cost of 200 mm dia PVC pipes:-00 mtr to 30 mtr |
| 126 | Supplying and fitting & fixing of I.S.I make 1.00 H.P single phase Submersible Pump set to give discharge of 3000 ltr/hour at a head of 40 mtr etc all complete as direction of EIC. |
| 127 | Supplying and fitting & fixing of D.O.L starter for 1.0 H.P single phase Submersible Pump etc all complete as per direction of E.I.C |
| 128 | Supplying and fitting & fixing of suitable cable and connecting the pump and starter etc all complete as per direction of E.I.C |
| 129 | Supplying and fitting & fixing of Plastic rope, M.S well cover, M.S clamp, etc all complete as per direction of Engineer-in-charge. |
| 130 | Supplying and fitting & fixing of HDPE pipes and pipe fittings with C.P Nippling and lowering to bore well, making connection to pumpset & testing etc all complete as per specification and the direction of the E.I.C. 32 mm dia HDPE Pipe |
| 131 | Supplying all materials, labour, T&P and Fitting and Fixing of Rotational moulded polythene cylindrical vertical water storage tank conforming to 15701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jamnuts, including hoisting upto a height of 5 mtr above G.Land placing the tank in required position including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 2000 lits capacity on the roof of GF |
| 132 | Supplying all materials, labour, T&P and construction of masonry staging with providing 1st class K.B. Brick work in C.M.(1:6) of 0.46mtr height in staging, 12 mm cement plaster in C.M (1:6), R.C.C. Beam of 0.25mx0.30mx2.60m & roof slab of 1.40mx1.40m in C.C (1:1.5:3) using 12mm size H.G.Chips including centering, shuttering, bending and binding of rod etc watering, curring, conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 2000 lits capacity on the roof of GF |
| 133 | Supplying all materials, labour, T&P and constructing Inspection Chamber of the following sizes with cement concrete (1:3:6) using 40 mm size HG metal on bed, 1st class KB Brick work in CM (1:6) moulding and shaping the channel inside and benching with C:C (1:1.5:3) using 12 mm size H.G chips, 12 mm thick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, RCC cover slab in C.C(1:1.5:3) using 12 mm size H.G chips with RCC man hole cover, etc. all complete as per approved specification and direction of E.I.C Inside size 760mm x 760mm x 460mm |
| 134 | Supplying all materials, labour, T&P and constructing Gully Trap chamber of the following inside size with 8 cm thick precast cover slab in CC (1:2:4) mix using 12 mm size H.G chips, foundation concrete (1:4:8) using 40 mm size HG metal on bed and around trap , !st class KB Brick work in CM (1:6) in F & P and inside 12 mm thick cement plaster (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap 150mmx150mm size C.I grating etc. all completed as per approved drawing, specification and direction of E.I.C. |
| 135 | Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class KB brick work in CM (1:6) for the remaining height at top, 12mm thick Cement Plaster (1:4) inside and outside over masonry brick work, gravel packing in the rear of well steining, RCC cover slab in CC (1:1.5:3) using 12mm HG chips, fitted with iron lifting handles. etc all complete as per approved specification and direction of the E.I.C. 0.90 m diax 2.0 m deep soakway pit |
| 136 | 1.20 m diax 2.0 m deep soakway pit |
| 137 | Metal Packaing 40mm size Crusher broken insite the pit5Nos x 0.80m x (0.785*1.2^2) |
| 138 | Metal Packaing 12mm size Crusher broken insite the pit |
| 139 | Sand Packaing insite the pit |
| 140 | Supplying all materials, labour, T&P and laying in trenches U-PVC SWR/4Kg/cm2 soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and providing bed concrete in P:C:C (1:4:8) using 40 mm size metal and haunch top the pipe with refilling of trenches etc all complete as per P.H specification and direction of the E.I.C.110mm Hunch Top |
| 141 | 160mm PVc Pipe all round Hunch top |
| 142 | Earthwork in all kinds of soil in excavation of foundation trenches within 50m initial lead and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.30m in depth etc all complete as per direction of the E.I.C.Initial lift upto 1.5 mtr2Nosx 4.37 m x 3.18 m x 1.50 m |
| 143 | From 1.5 mtr to 3.0 mtr depth2 Nosx 4.37 m x 3.18 m x 0.70 m |
| 144 | Supplying all materials, labour, T&P and filling in foundation and plinth with river sand well watered and rammed including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per the direction of the E.I.C.2 Nosx 4.37 m x 3.18 m x 0.15 m |
| 145 | Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 40mm H.G metal including watering, curing and conveyance of all materials to site payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.2Nosx 4.37 m x 3.18 m x 0.10 m |
| 146 | Supplying all materials, labour, T&P and providing plain cement concrete (1:1.5:3) with 12mm size H.G chips including watering, curing and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.2 Nosx 4.37 m x 3.18 m x 0.10 m 1.389 Cum2 Nosx3.07 m x 1.88 m x 0.038 m 0.219 Cum |
| 147 | Supplying all materials,labour, T&P and providing Brick work with K.B.Brick having crushing strength not less than 75 Kg/CM2 with dimensional tolerence of +/- 8% in C.M including watering, curring, conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.In Foundation and Plinth in C:M (1:4)2Nosx 2 x ( 4.07 + 1.88 ) m x 0.50 m x 1.10 m 2Nosx 2 x ( 3.82 + 1.88 ) m x 0.375 m x 0.80 m |
| 148 | Supplying all materials, labour, T&P and providing cement plaster on brick/stone work including watering,curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.12 mm thick C.P in C:M (1:3)2Nosx 2 x ( 3.07 + 1.88 ) m x 1.90 m 2Nosx 3.07 x 1.88 m |
| 149 | Supplying all materials, labour, T&P and providing cement punning on plastered surface including watering,curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.Same as above item 20mm C.P in 1:3 |
| 150 | Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for RCC work including false work and dismantling them after casting including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge.2Nosx 2 x (3.82 + 2.63 ) m x 0.125 m 2Nosx 3.07 m x 1.88 m |
| 151 | Supplying all materials, labour, T&P and providing M.S.reinforcements for RCC work including cutting, bending, binding, straightening and tying the grills and placing in position including cost of binding wire 18 to 20 gauge conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge. |
| 152 | Supplying all materials, labour, T&P and providing Reinforced cement concrete (1:1.5:3) with 12mm size H.G chips including watering, curing and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.2Nosx 3.82 m x 2.63 m x 0.125 m |
| 153 | Supplying all materials, labour, T&P and making M.S. Step Iron in 20mm Dia M.S Steel bars and fixing into walls of Manhole/ Septic Tanks duly embeded in C.C(1:2:4) etc all complete as per P.H specification and direction of the Engineer-in-charge. |
| 154 | Supplying all materials, labour, T&P and providing 50mm thick pre-cast R.C.C. baffle wall in R.C.C(1:1.5:3) including reinforcement cage using 12mm size HG chips fitted and fixed in position, finished smooth etc. complete including cutting grooves and mending good the damages etc all complete as per P.H specification and direction of the E.I.C.2Nosx 2.20 m x 0.45 m |
| 155 | Supplying all materials, labour, T&P and providing 160mm dia P.V.C Tee inside the septic tank including cutting holes and duly embeded in P.C.C(1:1.5:3) using 12mm size HG chips fitted and fixed in position and mending good the damages etc all complete as per P.H specification and direction of the E.I.C. |
| 156 | Supplying all materials, labour,T&P and providing 12mm thick cement flush pointing in C:M (1:3) to Brick Masonry works including watering curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge.2Nosx 2 x ( 4.07 + 2.88 ) m x 1.10 m 2Nosx 2 x ( 3.82 + 2.63 ) m x 0.80 m Nosx 2 x ( 4.07 + 2.63 ) m x 0.125 m |
| 157 | Supplying all materials, labour,T&P and filling Foundation and Plinth with excavated earth including watering, ramming etc all complete as per direction of the E.I.C. |
| 158 | SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm diameter U-PVC SWR pipes |
| 159 | 110mm U-PVC SWR P-trap |
| 160 | 110mm U-PVC SWR Single junction door |
| 161 | 110mm U-PVC SWR door bend |
| 162 | 110mm U-PVC SWR Offset |
| 163 | 110mm U-PVC SWR plain bend |
| 164 | 110mm U-PVC SWR vent cowl |
| 165 | 75 mm diameter U-PVC SWR pipes |
| 166 | 75 mm U-PVC SWR plain bend |
| 167 | 125 mm dia C.P Grating |
| 168 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling or floor G.I./PVC pipes and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling,and floor, testing all complete as per specification and the direction of the E.I.C. 20mm dia C- PVC pipes Internal |
| 169 | 25mm dia C-PVC pipes External |
| 170 | supplying all materials, labour, T&P and cutting holes through existing brick/stone masonry walls for taking GI/PVC pipes and fittings including making good the damages in cement mortar (1:4) etc. all complete as per P.H. specification and direction of E.I.C. R.C.C Roof/Chaja |
| 171 | Cutting Groove in wall or floor |
| 172 | Cutting hole(250 mm wall) |
| 173 | Cutting hole(375 mm wall) |
| 174 | Supplying all materials, labour, T&P and fixing porcelain glazed tiles in floors, on 25mm thick bed of cement mortar 1:1 joined with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. all complete as per specification and direction of the E.I.C.Ground Floor2nosx7.0x2.4m=34.00 Sqm |
| 175 | Supplying all materials, labour, T&P and fixing porcelain glazed tiles in dados/skirtings on 12mm thick cement plaster (1:3) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing etc. all complete as per direction of the E.I.C. Ground Floor2nos 35.00mx2.10=147.00 Sqm2nos x 2x2=8.0 Sqm |
| 176 | Supplying all materials, labour, T&P and fixing water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x30mm footrest etc all complete as per specification and direction of the E.I.C.580mm size Orissa pan(Hindware,Parryware) |
| 177 | Flat Back lipped wall urinal |
| 178 | Supplying all materials, labour, T&P and fixing Eoropian Watter closet and seat cover with 'P' trap plain etc all complete as per specification and direction of the E.I.C. |
| 179 | Supplying all materials, labour T&P and fitting & fixing 10 Litres capacity low level cistern with a pair of cast iron of m.s. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float, c.p. brass handle, unions and couplings for connection with inlet, outlet and overflow pipe. 32 mm C.P flush bend 15mm PVC inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting inlet pipe with supply main etc. all complete as per specification and direction of E.I.C (Cerra/ Parry ware/ Hindware) |
| 180 | Supplying all materials, labour T&P and fitting and fixing of C.P Shower(Parryware,Hindware) with 15mm or 20mm inlet with C.P Shower arm including polishing etc all complete as per specification and direction of the E.I.C 15 mm x 150mm dia C.P Shower with arm |
| 181 | Supplying all materials, labour T&P and fixing wash basins(Hindware,Parryware) with C.I. or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the E.I.C. 550mmx400mm size wash hand basin |
| 182 | Pedestal For Basin |
| 183 | Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C.sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the E.I.C. |
| 184 | Supplying all materials,labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the E.I.C 20mmx450mm long CP towel rail |
| 185 | Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the E.I.C |
| 186 | Supplying all materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia CP Bib Cock SB |
| 187 | 15mm dia CP Bib Cock LB |
| 188 | 15mm dia CP Pillar Cock |
| 189 | 15mm dia 2 in 1 way Bib Cock |
| 190 | 15mm dia CP Angle Stop Cock |
| 191 | 15mm dia CP Concealed Stop Cock |
| 192 | 25mm dia Brass Full Way Valve |
| 193 | Aquaguard Hot & Cold RO + UV Wall & Table Mount 11 L Storage Water Purifier |
| 194 | Factory made FRP(alternately called GRP) door frame of size 75mmx100mm fabricated using E-glass Chopped Strand Mat (CSM) U.V stabilised Inopthalic Gelcoat and impregnated with Inopthalic resin. The thickness of the GRP skins shall not be less than 2.00mm. The door frame consist of four segments which are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw. The GRP frame shall be provided with wooden reinforcement on six locations for high screw holding capacity for for fixing metallic hold fast and shall be consolidated by filling with medium density foam/plaster of paris with fibre reinforcement, Six numbers of 260mm x 25mm x 5mm size 'S' shaped M.S flat hold fast shall be provided with the frame. The material and process for manufacturing the door frames shall conform to RV-TIFAC composites Design Centre's standards and specifications. The finish of door frame will be plain colour white/ Ivory/ Beige/ Light grey/ Golden brown/Mahogany/ Teak wood/sand stone/Champagne/Pastel blue or any other colour using high quality pigments complete in all respect as per specification and direction of the E.I.C 8x( 2.10+0.75+2.10) |
| 195 | Factory made single leaf rigid FRP(alternately called GRP) sandwich composite door shutter of 32mm thick laminated with two GRP skins with wood grain finish fabricated using UV-stabilised Isopthalic Gelcoat and one layer of 450 gsm E-glass Chopped Strand Mat (CSM) impregnated with orthopthalic palyester resin. The thickness of the skins shall not be less than 1.50mm Expanded Polystyrone(EPS) structural foam panel of 29mm thickness and a density of 20kg/cu.mtr shall be used as core material. Wooden reinforcements made of seasoned sal wood block of cross section not less than 28mmx32mm and also necessary sal wood reinforcements for fitting the metal fittings such as tower bolts, aldrops, handles etc shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material, the sal wood reiforcements and the skins. The material and process for manufacturing the door shutters shall conform to RV-TIFAC composites Design Centre's standards and specifications and the door shutters tested in conformation to IS: 4020-1998. The finish of door shutter will be plain colour white/ Ivory/ Beige/Light grey/ Mahogany/Teak wood or any other colour using high quality pigments. Three heavy whight mild steel butt hinges type-I(ISI marked) size 100mm are to be fitted on one side of shutter. 8nos x(0.70x2.0)=11.00 Sqm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysSep 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender