Tender For Repair And Renovation Of Tourist Office At Phulbani In Kandhamala District.
Tender Value
23.54 Lakhs
Estimated cost
Bid Submission
17 Sep 2026
4 days left
EMD
23540
Bank guarantee accepted
Document Fee
6000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kandhamal → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Renovation Of Tourist Office At Phulbani In Kandhamala District.
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork in excavation in all kinds of soil upto 1.50mtr depth of foundation trenches for columns, basement, tie beams, walls and steps in following types of soil including moorum, hard stony earth, earth mixed with boulders, DI rocks etc but not requiring blasting with initial leads and lifts including dressing and leveling the bed sides up to required depth and depositing the excavated materials at places away from the work site with T&P for shoring, shuttering, dewatering if required etc. complete as per the drawing, design including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge. |
| 2 | Supplying and filling in foundation trenches and plinth, ditches with sand well-watered and rammed in layers not exceeding 23 cm. in depth with all lead and lift including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge. (Measurement will be taken on finished compacted section only). |
| 3 | Providing and lying plain cement concrete of proportion (1:3:6) in foundation and floors using Portland Slag Cement(PSC) with 4 cm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes all materials and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per specification and direction of Engineer-in-charge. |
| 4 | Providing, lifting, hoisting and laying Reinforced cement concrete of different RCC structure in foundation level of M-20 grade as per approved designs and drawings having a minimum compressive strength (in work test) 200 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. |
| 5 | a) Foundation - Column |
| 6 | b) Column & Beam |
| 7 | Providing & fixing TOR Fe-500 HYSD Reinforcement bars (SAIL /TATA /RINL) of required diameter and approved quality for Reinforced Cement Concrete work including straightening, cutting, bending, binding, welding(if approved) , joining (if necessary), tying the grills, hoisting, lowering and placing in position as per the approved design & drawings (BBS) with provision of standard fan hooks including the cost of all materials, cost of all labour, conveyance, taxes, loading, unloading, cost of binding wires of 18 to 20 gauge, T&P, etc, all complete as per the direction of Engineer-in-Charge. |
| 8 | Providing Brick work with Fly ash bricks Superstructure 25cm x 12cm x 8cm size having crushing strength not less than 75 kg/cm2 with dimensional tolerance +/ - 2 percent in cement mortar (1:6) ( 1 cement: 6 sand), with all necessary projection, splay cutting, circular moulding, corbelling, etc., including cost of all materials, labour, conveyance, loading ,and aunloadining, royalties, scaffolding, watering, curing, sundries, tools and plants, etc., as per the direction of the Engineer-in-charge. |
| 9 | Providing 12mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to smooth surface of brick masonry walls after racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge. |
| 10 | Labour for cleaning of Peripheral area |
| 11 | Scraping & cleaning of Old paints with wire brush /Blade or any other suitable equipment as per site requirement for providing surface for new painting works etc. including cost of all labours , sundries T&P etc. complete as per direction of Engineer-in-charge. |
| 12 | Painting two coats to the wall surface by using 100% premium Acrylic emulsion paint of approved make like NEROLAC ALLS CAPES 24 carrot emulsion/ BERGER luxel luxury silk emulsion / ASIAN Royal / ICI velvetouch or equivalent make of approved shade to interior wall surface over a coat of primer with water bond cement primer after preparing the surface smooth by applying putty punning with Synthetic Acrylic wall putty including finishing the surface smooth by sand papering in all heights including scaffolding charges with cost, conveyance, taxes of all materials, cost of all labours, etc. as required for the work complete in all respect. |
| 13 | Wall painting two coats with 100% Acrylic emulsion paint (1st quality) exterior grade(weather coat) of approved make & shade manufactured by reputed manufacture like NEROLAC /ASIAN /BERGER /DULOX or equivalent to make an even finished surface over a coat of primer with water bond cement primer in all heights with all scaffolding and staging charges including cost, conveyance, taxes of all materials, cost of all labour, etc. complete as per specification and direction of Engineer-in-Charge |
| 14 | Providing and painting two coats with synthetic enamel paint of approved quality and approved shade confirming to ISI on iron work to give an even shade over a coat of primer of approved quality and shade including sand papering and making the surface smooth in all floors at all height with cost, conveyance, loading, unloading and taxes of all materials, cost of all labour, sundries, T& P scaffolding and taxes of all materials, cost of all labour, sundries, T & P scaffolding etc. required for the work and complete in all respect as directed by the Engineer-in-charge |
| 15 | Supplying, fitting and fixing of M.S grills, grill gates with top and bottom rails, steel windows, steel doors, steel frames for doors and windows, staircase and parapet railing ( as per I.S. specification and as per approved drawings ) in proper position in all floors and at all height including making holes to brick walls/ R.C.C structure/wood work etc. and making good to the damaged walls/ structures with cement concrete (1:2:4) with black hard crusher broken granite stone chips of 12mm to 20mm size ( 20mm size not to exceeds 25% ) including watering and curing etc. complete in all respect as directed by the Engineer in charge ( W.I. / M.S. windows grills, grill gates, collapsible gates with top and bottom rails, steel windows, steel doors, steel frames for doors and windows, staircase and parapet railings square bar along with required nos. of nails and screws and other required materials of approved quality and approved size shall be supplied by the contractor at his own cost.) |
| 16 | Providing & fixing of wall panelling made out of Aluminium section B 9835 as Horizontal and vertical member placed @ 600mm c/c covered with 9mm thick BWR ply and 4mm thick century veneers make white(Product Sl No 231) oak & applied with cost of all materials, labours & T&P etc. complete in all respect as per the direction of the engineer-in-charge. |
| 17 | Supplying fitting and fixing in position flush door shutter of 32mm thick of Green / Mayur / Aeon or equivalent with 1mm sun mica (Royal touch) of approved quality and as per drawing & design with all necessary brass fittings, door closer (godrej, heavy duty) motrice lock (godrej heavy duty), handle, door stopper etc including cost of all materials, labour, all taxes, transportation, loading & unloading etc. complete as per specification and direction of Engineer –in-charge. |
| 18 | Providing and injecting chemical emulsion for pre - constructional antitermite treatment as per IS specification and creating a chemical barrier in bottom and sides of foundation trenches, top-surface of plinth filing junction of walls and floors along with external perimeter of the building expansion joints surrounding the pipes and cables etc. complete using approved quality of chemical emulsion of requisite quantity prescribed by the manufacturer as directed by the Engineer-in-charge including cost of all materials and labour etc. complete. |
| 19 | Surface preparation Removal of existing Felt if any & rendering the roof surface area of depressions, pot holes, abraded areas, worn out areas etc. with sand cement mortar admixed with a polymer modified SBR based emulsifier, filling of all cracks with SBR polymer(STP Make) admixed with cement & sand polymer modified putty and other necessary renderings like cutting of grooves along the parapet wall if any upto a height of 250 mm. & tucking in the membrane edges & sealing with polymer Motar , labour, equipment hire charges etc, complete at site and Providing and applying high performance torch applied APP based membrane Super Thermolay(STP Make) of 3mm thickness, APP Modified Waterproofing Membrane with Non Woven Polyester mat Reinforcement of 160 GSM Prefabricated& Self finished Five layered design super imposed with 20 micron Thermo fusible Film, by first applying Shalitex Primer (STP Make), Conforming to IS – 3384 @ 0.325 Kg per SQ.m (Oil based) & allowing it to dry & then torching of the membrane with the help of LPG/ Butane gas torch keeping overlapping of 4” at the side & 4” at the bottom & fusing of all the joints by gas torching & troweling with round shape smoll steel trowel & finally finishing with Bitumen based heat reflective/UV resistant Aluminioum paint, i.e Super Silver Shield @ 0.125 Kg/Sq.m & complete in all respect as per Manufacture specification. |
| 20 | Providing & fitting,fixing of Wall Paper on Walls (Greamz / Flow / Icon of marshall make ) including cost,conveyance,royalty,taxes of all materials,all labour,cost,sundries,T&P etc Complete as per the direction of the E.I.C. |
| 21 | Providing fixing of 1mm laminate after dismantaling of old laminate on flush door etc.complete in all respect as per direction of the E-I-C. |
| 22 | Providing and fixing in position False ceiling Calsium Silicate board and aceiling as per the pattern and design made from 12mm tk CalsiumSilicate board fixed with main G.I frame channels all along the wall shall be provided. The frame work to be suspended with G.I flats or adjustable M.S rod from intermediate channels using nuts and bolts as recommended using rawls plugs 12.5 mm dia bolts and soft cleat 27mmx 37mmx25mm. Arrangements are to be madeto accommodate light fixtures, curtain rails by forming recessed channels which shall be done with jointing compound and paper tape .Ceiling to be levelled and free from cracks . Items to be completed in all respect to the architect's approval .Openings to be made in the ceiling as per architect 's approval .to accommodate lighting fixtures.Opening in the ceiling are to be tied withperimeter channel complete with the cost of all labour and material i/c painting with acrylic emulsion painting of two coats with primer coat and hardware asper drawing and specification and direction of Engineer-in-charge or consultant. |
| 23 | Providing and fixing of 35mm thick WPC Door Shutter(Solid) with teak edge leaping to the periphery of the shutter with pilishing as per detailed drawing with including, all hardwares & fixtures, SS tower bolt(150mm),Door stopper,SS aldrop(250mm),SS handle(200mm length),ss handle (150mm length) & SS Butt hinges -125mm x 65mm x2.12mm .including cost, conveyance, loading, T&P required for the work etc. complete in all respect as directed by the Engineer-in-charge |
| 24 | Providing and fixing in position WPC door frame with appropriate length of ETA Approved carbon steel galvanized (minimum 5 microns) double threaded 6.8 grade Polyamide PA 6 grade sleeve HRD C 10 anchor suitable for fastenings both on concrete & masonary/aerated blocks including cost of all materials, labours, T & P etc required for the work. complete in all respect as directed by the Engineer-in-charge |
| 25 | PH WORK |
| 26 | Providing and installing vitreous china Half pedestal basin with all fittings Hindware FLOORA 10114 & 91115 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 27 | Supplying all materials, labour, T&P and fixing standard sized CP Soap dish holder of Jaquar Cat. No.-ACN-1131N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 28 | Supplying all materials, labour, T&P and fixing standard sized Towel ring in polished chrome of Jaquare Cat. ACN 1121BN or equivalent etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 29 | Supplying all materials, labour, T&P and fixing standard sized CP Soap dish holder of Jaquar Cat. No.-ACN-1131N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 30 | Supplying all materials, labour, T&P and fixing standard sized pillar cock of Jaquar FUS -29021N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 31 | Supplying all materials, labour, T&P and fixing of 15mm dia CP two way bib cock with wall flange Jaquar FUS -29041 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 32 | Supplying all materials, labour, T&P and fixing of 15mm dia CP Angular stop cock with wall flange. Jaquar FUS 29053 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 33 | Supplying all materials, labour, T&P and fixing of 15mm dia CP bib cock long body Jaquar FUS-29037 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 34 | Supplying all materials, labour, T&P and fixing of Glass self Make Jaquar CAN 1171N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 35 | Supplying all materials, labour, T&P and fixing of Towel Rail Jaquar ACN-1111BSM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 36 | Supplying all materials, labour, T&P and fixing of Wall Mixture Jaquar FUS29273UPR or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 37 | Supplying all materials, labour, T&P and fixing of Health faucet Jaquar ALD 573 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 38 | Providing and fixing circular type stainless steel jalli (grating) with hole for floor /nahani trap etc complete as per PH specification and direction of the engineer in charge |
| 39 | Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the Engineer in charge. |
| 40 | Supplying all materials, labour, T&P, fitting and fixing UPVC SWR pipes & fittings of approved make confirming to ISI type-A, both below and above ground level / floor and on walls including supply of bobbins, nains, screws, wooden cleats, pipe clips as per requirement, including earth work in excavation and fitting, including cuting walls and floor and making good the damages with cement concrete (1:2:4) with hard granite chips, incluidng scaffolding wherever necessary all complete as per the PH specification and direction of the Engineer-in-charge. |
| 41 | a) 160mm dia |
| 42 | b) 110mm dia |
| 43 | c) 75mm dia |
| 44 | Providing and fixing square mouth S.W gully trap class SP-1 complete with CI grating brick masonry chamber with water tight CI cover with frame of 300X300mm size (inside),the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per the standard desifn. brick masonry chamber of size 180 X 150 mm size complete as per approved specification and direction of the Engineer in charge. |
| 45 | Providing & Constructing manhole chamber of following sizes including earth work in excavation, back filling,KB Brick masonary work four sides to make chamber, Plain Cement Concrete (1:2:4) 30cm depth in bottom of chamber with 1/2\\" down graded Crusher broken hard granite chips, inside cement plaster 12mm thick in CM 1:3 & neat cement punning , Top slab in RCC ( 1:2:4) 15cm thick with necessary centering & shuttering, TMT steel reinforcement @10 cm c/c both way, cast iron manhole cover with frame, making channel in floor of chamber with necessary slope complete with all materials, labour, tools, plant, royalty, curing, etc. in all respects as per the direction of Engineer-in-charge. |
| 46 | a) Plain manhole inside 900x800and 450mm deep with cast iron manhole and frame(light duty) rectangular type 450mmx610mm internal dimension. |
| 47 | Supplying all materials, labour, T&P and fixing including conveyance of all materials etc as per direction of Engineer-in-charge. |
| 48 | a) Aldrop |
| 49 | b) Door handle |
| 50 | c) Door stopper |
| 51 | d) Tower bolt |
| 52 | e) Godrej door closer heavy duty (ULRated, 68 Kg) |
| 53 | Furniture |
| 54 | Supply of Executive Table, 392 Particle board top size -W1600XD700XH750, Geeken Make |
| 55 | Conference Table, Particle board & MDF Top (without flip - up box) Size -W4500XD1500XH750, Geeken Make |
| 56 | Midium back chair , PP Arm , Gas lift ,Nylon base , mesh back & seat leatherette Tapestry swivel tilt, Geeken make |
| 57 | Midium back chair , PU Arm , Gas lift ,Nylon base , mesh back & seat Fabric, Tapestry synchro tilt, Geeken make |
| 58 | High back chair , PP Arms , Gas lift Crome base ,leatherette Tapestry swivel tilt, Geeken make |
| 59 | Midum back chair , PP Arms , Gas lift Crome base ,leatherette Tapestry swivel tilt, Geeken make |
| 60 | Steel Rack (Single Face) Thick ness - 0.8mm , 4adjustable shelves, W925xD300XH1800 Geeken make |
| 61 | 3Seater Sofa , 3 seater with 4 arm Al. arm and leg, Metal Powder coated cross beam , metal insert pu seat black colour size - L-1625XD660XH870 Geeken make |
| 62 | 2Seater Sofa , 2 seater with 4 arm Al. arm and leg, Metal Powder coated cross beam , metal insert pu seat black colour size - L-1100XD660XH870 Geeken make |
| 63 | 1Seater Sofa , 1 seater with 2 arm Al. arm and leg, Metal Powder coated cross beam , metal insert pu seat black colour size - L-550XD660XH870 Geeken make |
| 64 | Incumbency chart size - H 4'-0\\"XW-2'-6\\" |
| 65 | Notice Board size - W 4'-0\\"XH-2'-6\\" |
| 66 | Electrical |
| 67 | Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI/V-Guard with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/ Norpak/ Anchor /Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo) /legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) ( flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. |
| 68 | GROUP-A |
| 69 | GROUP-B |
| 70 | GROUP-C |
| 71 | Supplying ,fixing of 6A Plug on the same board in existing switch board with complete fitting by 01 no of 6A switch & socket (modular type)( ( flame retradant type)) & other required accessories of ISI marked as approved as per direction of Engg. -in -Charge. Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 72 | Supplying,fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket(modular type)( ( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius ) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 73 | Supplying,fixing of 2 nos 6A Plug on the separate board with complete fitting by 02 no of 6A switch & socket(modular type)( (flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 74 | Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)(( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) (For equipement power)All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 75 | S/F of 5 step type Modular electronic Fan Regulator ISI Marked with all connection complete in all respect as per direction of Engineer in charge ( Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) |
| 76 | Supply and fixing CALL bell (Ding dong type) /Buzzer on the existing switch box/cover.Make- Havells/Anchor as required as per direction of Engg.-in-Charge.All the Components should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 77 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty conduit (LDB to LSB/LIGHT CKT)(2X1.5+1X1.5) |
| 78 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit.(BDB to LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5) |
| 79 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit .(PDB to PSB/ POWER POINT/AC POINT) (2X4+1X1.5) |
| 80 | Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series, single poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 . the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years. |
| 81 | Supplying, installation, of exhaust fan of heavy duty 300 mm sweep 1400 rpm with louvers (Make- Havells/Crompton/Usha/Orient/Bajaj ) of exhaust fan in the existing wall, including fixing & conntection as required as per direction of Engg.-in-Charge. Replacement Warranty will be 2 years. |
| 82 | Supplying, installation, testing and commssioning of 1200 mm sweep Copper wound BLDC ceiling fan with aluminium blades having wattage not more than 28W and air delivery ≥215m3/min Make-Crompton Energion Groove /Havells Efficiencia Neo/Usha Technix /Bajaj Turbo Pro 12DC5 ) including wiring the down rod of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper conductor, single core cable etc. as required as per direction of Engg.-in-Charge,Replacement Warranty will be 4 years. |
| 83 | SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 2 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years . |
| 84 | SITC of Sleek LED 10 watt light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj)The luminaire should be Replacement Warranty will be 2 years |
| 85 | SITC of 3 watt LED Ceiling Recessed mounted spot light in different Colour Aesthetically designed lens based of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 86 | Supplying and fixing of Energy efficient surface /recess mounted square /round shape 18 W LED luminaire of dimension of consists of white powder coated , die-cast Alluminium housing with high quality frosted diffuser for glare-free uniform lighting distribution with wattage not more than 18 watt and lumen output of 1800 lumens, , CRI not less than 80,CCT of 6000 degree K,THD less than 10%, with electronic driver, internal surge protection of 3 KV , L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj).The luminaire should be Replacement Warranty will be 2 years |
| 87 | Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover of reputed make,ISI marked with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. Make-POLYCAB/FINOLEX/HAVELLS/KEI/RR Kabel/Gloster |
| 88 | Supplying, Installation, Testing & Commissioning of 1.5 TR Split AC with 5 Star BEE Rating of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge.(LG-AS-Q20JWZE/ O General-ASGG18CGWA-B/ Daikin-FTKU50XV16) ( Rooom 101,102,103,106, 108 & 109 ) |
| 89 | Supplying, Installation, Testing & Commissioning of 4 Kva wall hanging Stablizer of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. (Make-V-Guard/ Microtek) |
| 90 | Supply,installation & fabrication of MS base frame for outdoor unit and other nesessary material to complete the job as required as per the direction of Engineer-in-Charge. |
| 91 | Supply,installation of hard/soft ISI marked copper refrigerant piping of size 5/8 inch and 1/4 inch for suction and liquid line with 3 corex4 sqmm FRLS Copper control cable alongwith 25 mm weather proof closed cell nitrile insulation ,complete with fitting of bends and other nesessary material to complete the job. |
| 92 | Supply,installation & fabrication of 25mm nom. Dia pipe Insulated drain water piping from indoor to nearest drain point separate to all and other nesessary material to complete the job. |
| 93 | Supply, installation, testing & commissioning of 2500 VA (2.5 KVA) Sine Wave inverter with dual-battery (24V) 200 AH Inverter System including all accessories for power backup etc complete with all materials & labour as required as per the direction of Engineer-in-Charge. (Make Luminous/ Microtek) |
| 94 | Supply, Installation, Testing & Commissioning of Indoor Dome IR Network Camera (1/2.7\\" CMOS sensor, Mini. Pixel of 2560*1920 or higher video quality, frame rate of Up To 25fps @ 2MP, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30mtr IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for noise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and out etc complete with connection as required for the work as per direction of Engineer-in-Charge. (Make- CP Plus / Dahua / Prama) |
| 95 | Supply and Installation of outdoor Bullet IR Network Camera 1/2.7\\" CMOS, ICR, 2592*1944@ 25fps, 2MP H.265/H.264/MJPEG, Triple streams, DC12V & PoE, Micro SD card slot up to 256 GB, Alarm in/out , Audio 1/1, IP67, 2.7-13.5mm Motorized Varifocal lens, IR anti-reflection window, Built-in bracket, IR range: up to 50m, Digital WDR Range, 3D-DNR for noise reduction, Audio In and Out, Alam in and Out IPv4 network supported, IP67 rated for weather proofing etc complete with connection as required for the work as per direction of Engineer-in-Charge. (Make- CP Plus / Dahua / Prama) |
| 96 | Supplying, installation, testing & commissioning of Smart LED Monitor UHD,Vibrant Viewing in Ultra High Resolution, commercial type of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. (Make- Frontech/ Zebronics/ Secureye ) |
| 97 | Supply, Installation, Testing & Commissioning of 8 CH NVR , 2TB Hard disk, 8 Port GIGA POE switch & 4u Rack etc complete with connection as required for the work as per direction of Engineer-in-Charge. ( NVR - CP Plus / Dahua / Prama , PoE - Hi-Focus / CP Plus / D Link, Hard Disc - Seagate/ WD ) |
| 98 | Supply, laying, Testing & Commissioning of Cat 6 4-pair UTP Cable etc complete with connection as required for the work as per direction of Engineer-in-Charge. ( Make - D Link/ Digisol/ Prama ) |
| 99 | Supply and Installation of HP (440G9) All In One Desktop-14th Gen, Intel Core i-5 Processor, Windows-11, Ms Office, 16GB Ram, 512 SSD, 23.8'' Display (3 Year Onsite Warranty) etc complete with all materials & labour as required as per the direction of Engineer-in Charge. |
| 100 | Supply and Installation of Luminous 600VA UPS etc complete with all materials & labour as required as per the direction of Engineer-in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysSep 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender