Tender For special Repair/Replacement Of Lt Oh Conductor To Underground Cable Inside Area Of Signal Regt Under Ge Khumbathang
Tender Value
Ref. Documents
Estimated cost
Bid Submission
26 Sep 2026
15 days left
EMD
66500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kargil → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair/Replacement Of Lt Oh Conductor To Underground Cable Inside Area Of Signal Regt Under Ge Khumbathang
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of ACSR or AAC Conductor complete all as specified and directed. |
| 2 | Dismantling cross arms of MS channel or angle section etc comlete and setting aside for re-use with in 50m complete all as specified and directed. |
| 3 | Dismantling insulators any type and size complete all as specified and directed. |
| 4 | Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth and getting it out for laying of cable / pole etc in hard/dense soil |
| 5 | Returning, filling in, including spreading, leveling watering, and well ramming in layers not exc 25 cm in hard/dense soil all as directed. |
| 6 | Removing excavated material n.exc 50m and depositing where directed at a level exc. 1.5 cm above the starting point all as directed. |
| 7 | Supplying and laying double walled corrugated HDPE Pipes of size 110 mm dia as per IS 16205 Anti termite, Anti Rodency and Non flame propagation propety etc for protection of LT cables complete all as specified and directed |
| 8 | Supplying and laying double walled corrugated HDPE Pipes of size 40 mm dia as per IS 16205 Anti termite, Anti Rodency and Non flame propagation propety etc for protection of LT cables complete all as specified and directed |
| 9 | Supply laying,jointing & testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor,1100 volt grade laid in trenches,ducts,drawn through pipes across the road/path/along poles/floors/equipment etc of size 150 sq mm 3.5 core in Replacement of ACSR conductor. |
| 10 | All as per item srl item No. 9 here-in-before but of size 120 sqmm 3.5 core |
| 11 | All as per item srl item No. 9 here-in-before but of size 95 sqmm 3.5 core |
| 12 | All as per item srl item No. 9 here-in-before but of size 70 sqmm 3.5 core |
| 13 | All as per item srl item No. 9 here-in-before but of size 50 sqmm 3.5 core |
| 14 | All as per item srl item No. 9 here-in-before but of size 35 sqmm 3.5 core |
| 15 | All as per item srl item No. 9 here-in-before but of size 10 sqmm 4 core |
| 16 | Supply installing, testing and commissioning of LT Panel outdoor kiosk type of Size 1.8 x 1.5 x 0.5 Mtr factory made of angle iron 65mmx 65mmx 6mm on all side welded to 3.15 mm thick CRCA sheet steel for outer compartment and 2.0 mm thick for inner compartment with openable shutteron both sides ( front and rear) , having locking arrangement totally enclosed weather proof outdoor spray painted internally and externally with two coats of synthetic enamel paint over a coat of primer suitable for 440 volts, 3 phase, 4 wire, 50 Hz with Aluminium bas bar of capacity 800 Amps AC supply, electrically connected as per norms and fitted with following accessories all as specified and directed by the Engr-in Charge. (Note:- LT panel shall be mounted on PCC 1:2:4 type B-1 with 20 mm graded stone aggregate foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item. The panels shall be of CPRI approved Note:- Drg of panel shall got approved before execution at site. INCOMMER Incoming MCCB, 415V, 4 pole, 400 Amps, 36 KA, Ics =100% IcuIndicator Lamp-01 Set (Set of three)Voltmeter 0-500 Volt , 415V , 50 Hz ,with selector switches -01 setAmmeter 0- 500 Amps with CTs, 415V 50 Hz with selector switches -01 setOUTGOINGMCCB, 415V, 4 pole, 250 Amps, 25 KA -01 No MCCB 4 pole 200 amp, 415V, 36 KA, 4 pole , 01Nos MCCB 4 pole 63 amp, 415V, 16 KA, 4 pole , 01 Nos MCB SPN 40 Amps , 230V, 50 Hz - 01 Nos |
| 17 | Supply installing, testing and commissioning of LT Panel outdoor kiosk type of Size 1.5 x 1.2 x 0.5 factory made of angle iron 65mmx 65mmx 6mm on all side welded to 3.15 mm thick CRCA sheet steel for outer compartment and 2.0 mm thick for inner compartment with openable shutteron both sides ( front and rear) , having locking arrangement totally enclosed weather proof outdoor spray painted internally and externally with two coats of synthetic enamel paint over a coat of primer suitable for 440 volts, 3 phase, 4 wire, 50 Hz with Aluminium bas bar of capacity 600 Amps AC supply, electrically connected as per norms and fitted with following accessories all as specified and directed by the Engr-in Charge. (Note:- LT panel shall be mounted on PCC 1:2:4 type B-1 with 20 mm graded stone aggregate foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item. The panels shall be of CPRI approved Note:- Drg of panel shall got approved before execution at site. INCOMMER Incoming MCCB, 415V, 4 pole, 250 Amps, 25 KA, Ics =100% IcuIndicator Lamp-01 Set (Set of three)Voltmeter 0-500 Volt , 415V , 50 Hz ,with selector switches -01 setAmmeter 0- 500 Amps with CTs, 415V 50 Hz with selector switches -01 setOUTGOINGMCCB, 415V, 4 pole, 160 Amps, 25 KA -01 No MCCB 4 pole 125 amp, 415V, 25 KA, 4 pole , 01 Nos MCCB 4 pole 63 amp, 415V, 16 KA, 4 pole , 01 Nos MCB SPN 40 Amps , 230V, 50 Hz - 01 Nos |
| 18 | Supply installing, testing and commissioning of Bus bar junction box panel outdoor kiosk type Size 1.5 x 1.2 x 0.3 Mtr factory made of angle iron 65mmx 65mmx 6mm on all side welded to 3.15 mm thick CRCA sheet steel for outer compartment and 2.0 mm thick for inner compartment with openable shutteron both sides ( front and rear) , having locking arrangement totally enclosed weather proof outdoor spray painted internally and externally with two coats of synthetic enamel paint over a coat of primer suitable for 440 volts, 3 phase, 4 wire, 50 Hz with Aluminium bas bar of capacity 800 Amps AC supply, electrically connected as per norms and fitted with following accessories all as specified and directed by the Engr-in Charge. (Note:- Bus bar junction box shall be mounted on PCC 1:2:4 type B-1 with 20 mm graded stone aggregate foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item. Note:- Drg of bus bar junction box panel shall got approved before execution at site. INCOMMER/OUT GOINGIncoming MCCB, 415V, 4 pole, 400 Amps, 36 KA, Ics =100% Icu -01 nosIndicator Lamp-01 Set (Set of three) |
| 19 | S&F in repair Junction box made out of FRP sheet, ready made type having aluminium bus bar of capacity 100 Amps 4 Nos including bakelite connector of size 300x200x115 with necessary connector , MCB 6 Amps and entry of gland and fixing arrangement to fix the box on plinth/wall by providing MS clamp and nut bolt Complete all as specified and directed by Engineer-in-Charge. |
| 20 | Supply, fixing, connecting and testing in replacement integral LED Street light fitting, 60 watts with pressure die cast aluminium housing IP66 with mounting bracket and all accessories and connecting the same to electric source with using copper conductor 1.5 Sq mm PVC insulated flexible three core cable , including all accessories and fixing the light fitting to pole complete all as specified and directed.Make :- Havells/Philips or equivalent others make as specified. |
| 21 | S & F in replacement PVC insulated stranded aluminium conductor cable sheated 2.5 sqmm flat twin core for connection for street light fitting with over head lines /services connection complete all as specified and directed. |
| 22 | S & F in replacment GI pipe light grade bracket 40mm dia, 1.5m long bent to shape as required for fixing of street lights on poles/walls including nuts, bolts, washers , Clamps (02 sets) of suitable size complete all as specified and directed. |
| 23 | Earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised iron strip 25 X 4 mm as earthing lead by means of bolts, nuts, check nuts & washers etc made of GI and connected to earthing test point all as shown in electrical plate No. 3 of SSR Part I of 2009.00 & as specified or indicated and testing on completion including exaction/earth work in any type of strata PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm), funnel with wire mesh, I watering pipe of 20 mm bore medium grade and lugs, including galvanised iron strip 25 x 4 mm with GI protection pipe of 40 mm medium grade 7.5 meter long, etc complete all as specified. |
| 24 | Deduct Credit for Demolished/Dismantled material Rs (-) 00 (Minus) as listed in Schedule 'A' Part-II (Credit Schedule)Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender